Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for BK Precision 9110
Summary of Contents for BK Precision 9110
- Page 1 Model: 9110, 9111 Multi Range DC Power Supply USER MANUAL...
-
Page 2: Safety Summary
Safety Summary The following safety precautions apply to both operating and maintenance personnel and must be followed during all phases of operation, service, and repair of this instrument. Before applying power to this instrument: • Read and understand the safety and operational information in this manual. •... - Page 3 to the primary power entering a building or other outdoor wiring. Do not use this instrument in an electrical environment with a higher category rating than what is specified in this manual for this instrument. You must ensure that each accessory you use with this instrument has a category rating equal to or higher than the instrument's category rating to maintain the instrument's category rating.
- Page 4 Do not operate the instrument in the presence of flammable gases or vapors, fumes, or finely-divided particulates. The instrument is designed to be used in office-type indoor environments. Do not operate the instrument • In the presence of noxious, corrosive, or flammable fumes, gases, vapors, chemicals, or finely-divided particulates.
- Page 5 Do not clean the instrument, its switches, or its terminals with contact cleaners, abrasives, lubricants, solvents, acids/bases, or other such chemicals. Clean the instrument only with a clean dry lint-free cloth or as instructed in this manual. Not for critical applications This instrument is not authorized for use in contact with the human body or for use as a component in a life-support device or system.
- Page 6 ratings, and current ratings specified in this manual or on the back of the instrument. Failure to do so may damage the instrument, lead to a safety hazard, or cause a fire. Failure to use the specified fuses will void the warranty. Servicing Do not substitute parts that are not approved by B&K Precision or modify this instrument.
-
Page 7: Compliance Statements
Compliance Statements Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This product is subject to Directive 2002/96/EC of the European Parliament and the Council of the European Union on waste electrical and electronic equipment (WEEE) , and in jurisdictions adopting that Directive, is marked as being put on the market after August 13, 2005, and should not be... -
Page 8: Ce Declaration Of Conformity
CE Declaration of Conformity The instrument meets the requirements of 2006/95/EC Low Voltage Directive and 2004/108/EC Electromagnetic Compatibility Directive with the following standards. Low Voltage Directive EN61010-1: 2001 EMC Directive EN 61000-3-2: 2006 EN 61000-3-3: 1995+A1: 2001+A2: 2005 EN 61000-4-2 / -3 / -4 / -5 / -6 / -11 EN 61326-1: 2006... -
Page 9: Safety Symbols
Safety Symbols CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Chassis (earth ground) symbol. On (Power) Off (Power) DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. -
Page 10: Front Panel Layout
Front Panel layout Set Voltage indicator CC mode indicator Voltage value CV mode indicator OCP indicator Cursor position B or preset B is active OVP indicator Cursor position A or preset A is active Cursor position C or preset C is active Preset mode indicator Cursor position D or preset D is active Keys locked indicator... - Page 11 Introduction The 9110 and 9111 are unlike conventional power supplies with fixed output ratings. They automatically recalculate voltage/current limits for each setting, forming a constant power, hyperbolic shaped boundary, as illustrated in the diagram below. Any Volt/Amp combination that doesn’t exceed 100W, 60V or 5A (or 180W, 60V or 8A for 9111) can be set.
- Page 12 Features Digitally controlled, mixed linear/switching mode DC p ower supply 10mV/1mA resolution over the full range Bright, easy to read display Low ripple and noise Very compact size and light weight Output ON/OFF Control High reliability due to OVP, OCP and OTP (over voltage, over current, over temperature) protection CV (Constant Voltage) and CC (Constant Current) operation Store/Recall 100 groups with 4 sets of Volt/Amp memories each...
-
Page 13: Installation
Report any damage to the shipping agent immediately. Save the original packing carton for possible future reshipment. Every instrument is shipped with the following contents: • 1x 9110/9111 DC Power Supply • 1x User Manual • 1x AC Power Cord Verify that all items above are included in the shipping container. -
Page 14: Fuse Replacement
Fuse Replacement Follow the steps below to replace or check the fuse. 1. Locate the fuse box next to the AC input connector in the rear panel. 2. With a small flat blade screwdriver, insert into the fuse box slit to pull and slide out the fuse box as indicated below. -
Page 15: Quick Start
Quick Start Set Voltage Set Voltage 9110 Press the key to turn the “V” D V/A 100W Multi Range 60V/5A DC Power Supply indicator on. Now you can set the voltage value. Use the cursor keys to highlight the desired digit then adjust... -
Page 16: Key Lock Function
Now the keys and the knob are locked and the Lock LED is lit. Press the Shift key followed by the Lock key again to disable the Lock function. OVP Function 9110 Press then press and hold the Shift 100W Multi Range 60V/5A DC Power Supply (Setup) key for 3 seconds. -
Page 17: Key Sound
Key sound 9110 9110 100W Multi Range 60V/5A DC Power Supply 100W Multi Range 60V/5A DC Power Supply Once the OCP value is set, press to enter the BEEP mode. Use the knob to turn the key sound ON or OFF. -
Page 18: Troubleshooting Hints
Storing Voltage/Current sets Store up to four sets of voltage/current values to the group number assigned in the previous paragraph. Press Shift followed by the (Save) key. All 4 cursor LEDs A B C D will blink simultaneously. Press one of the D V/A keys to assign one of the 4 available memory location within this group. -
Page 19: Specification
Specification 9110 9111 Output Rating Voltage 0 – 60 V 0 – 60 V Current 0 – 5 A 0 – 8 A Power 100 W 180 W Load Regulation Voltage < 0.01% + 3 mV < 0.01% + 5 mV Current <... -
Page 20: Service Information
SERVICE INFORMATION Warranty Service: Please go to the support and service section on our website at www.bkprecision.com to obtain a RMA #. Return the product in the original packaging with proof of purchase to the address below. Clearly state on the RMA the performance problem and return any leads, probes, connectors and accessories that you are using with the device. -
Page 21: Limited One-Year Warranty
LIMITED ONE-YEAR WARRANTY B&K Precision Corp. warrants to the original purchaser that its products and the component parts thereof, will be free from defects in workmanship and materials for a period of one year from date of purchase. B&K Precision Corp. will, without charge, repair or replace, at its option, defective product or component parts. Returned product must be accompanied by proof of the purchase date in the form of a sales receipt. - Page 22 22820 Savi Ranch Parkway Yorba Linda, CA 92887 www.bkprecision.com © 2007 - 2014 B&K Precision Corp. Printed in China v062514...
Need help?
Do you have a question about the 9110 and is the answer not in the manual?
Questions and answers