Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MINN KOTA 1355975
Summary of Contents for MINN KOTA 1355975
- Page 1 PONTOON HAND CONTROL BOW-MOUNT TROLLING MOTOR USER MANUAL...
- Page 2 FEATURES Tilt-Twist Handle Controls: On/Off, Speed, Forward/ Reverse and Direction Adjustable Depth Collar Steering Tension Knob Mounting Bracket Lifetime Warranty Flexible Composite Shaft Cool Quiet Power Motor Propeller Specifications subject to change without notice. *This diagram is for reference only and may differ from your actual motor.
-
Page 3: Mount Installation
9/32 drill bit. NOTE: The four front mounting holes uses the same bolt pattern as used on Minn Kota quick release plates MKA-21, RTA- 17, MKA-16-02 and MKA-32. The pontoon mount may be attached to any of these for your mounting convenience. Deploy the motor and remove the motor assembly from the mount by loosening the Steering Tension Knob and opening the door. -
Page 4: Battery Wiring & Installation
CAUTION: These guidelines apply to general rigging to support your Minn Kota motor. Powering multiple motors or additional electrical devices from the same power circuit may impact the recommended conductor gauge and circuit breaker size. If you are using wire longer than that provided with your unit, follow the conductor gauge and circuit breaker sizing table below. -
Page 5: Selecting The Correct Batteries
• It is highly recommended that a circuit breaker or fuse be used with this trolling motor. Refer to “Conductor Gauge and Circuit Breaker Sizing Table” in the previous section to fi nd the appropriate circuit breaker or fuse for your motor. For motors requiring a 60-amp breaker, the Minn Kota MKR-19 60-amp circuit breaker is recommended. CONNECTING THE BATTERIES 12 VOLT SYSTEMS: 1. -
Page 6: Motor Wiring Diagram
MOTOR WIRING DIAGRAM NOTE: This is a universal, multi-voltage diagram. Double-check your motor's voltage for proper connections. Over-Current Protection Devices not shown in this illustration. FIVE SPEED SWITCH BLACK MOTOR BATTERY 1 BATTERY 1 BATTERY 2... -
Page 7: Using & Adjusting The Motor
USING & ADJUSTING THE MOTOR ADJUSTING THE DEPTH OF THE MOTOR Adjustable Depth Collar Knob When setting the depth be sure the top of the motor is submerged at least Steering Tension Knob 12” to avoid churning or agitation of surface water. The propeller must be completely submerged. - Page 8 USING & ADJUSTING THE MOTOR ADJUSTING THE TILT TWIST TILLER™ The twist grip tiller handle is shipped in the down position. Firmly pull the handle up to the horizontal position. The handle has fi ve available positions: 45˚ down, horizontal, 15˚, 30˚, and 45˚ tilted up. The handle locks in the horizontal position but can be tilted down by pushing the release button Handle Controls: Off/On, Steering,...
-
Page 9: Service And Maintenance
SERVICE & MAINTENANCE PROPELLER REPLACEMENT TOOLS AND RESOURCES REQUIRED: Propeller • Box End Wrench Slot End - 1/2” for motors with 70 lbs thrust or lower. - 9/16” for motors with 80 lbs thrust or higher. Prop Nut Washer • Screwdriver (optional) CAUTION: Disconnect the motor from the battery before beginning any prop work or... -
Page 10: Troubleshooting And Repair
TROUBLESHOOTING & REPAIR 1. Motor fails to run or lacks power: • Check battery connections for proper polarity. • Make sure terminals are clean and corrosion free. Use fi ne sandpaper or emery cloth to clean terminals. • Check battery water level. Add water if needed. 2. -
Page 11: Parts Diagram
70 LBS THRU - 24 VOLT - 52” SHA This page provides Minn Kota® WEEE compliance disassembly instructions. For more information about where you should dispose of your waste equipment for recycling and recovery and/or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased. -
Page 12: Parts List
PARTS LIST PONTOON HC 70 70 LBS THRU - 24 VOLT - 52” SHA PART PART ITEM DESCRIPTION ITEM DESCRIPTION NUMBER NUMBER 2-100-119 ARMATURE SEMBLY 12 V 3.625 2303412 SCREW — 6-20 X 5/8 SELF TAP 140-010 BALL BEARING 2033400 SCREW —... -
Page 13: Environmental Compliance Statement
Minn Kota motors are not subject to the disposal regulations EAG-VO (electric devices directive) that implements the WEEE directive. Nevertheless never dispose of your Minn Kota motor in a garbage bin but at the proper place of collection of your local town council. -
Page 14: Recommended Accessories
Stop buying new batteries and start taking care of the ones you’ve got. Many chargers can actually damage your battery over time – creating shorter run times and shorter overall life. Digitally controlled Minn Kota chargers are designed to provide the fastest charge that protect and extend battery life.
Need help?
Do you have a question about the 1355975 and is the answer not in the manual?
Questions and answers