® • Magne-Traction Table of contents Transformer operations Running your CS #2 GP-9 with a Lionel transformer Using your CS #2 GP-9’s Electrocouplers A note on Magne-Traction Your CS #2 GP-9’s Railsounds system—the basics Experiencing the range of your CS #2 GP-9’s Railsounds system Notes on Railsounds Installing the Lionel no.
Transformer operations Running your CS #2 GP-9 with a Lionel transformer Place your CS #2 GP-9 locomotive on Lionel or Lionel-compatible O gauge track. • Note the pull of Magne-Traction between your CS #2 GP-9 and the steel track. Magnetized wheels and axles increase your pulling power (more than 25 cars on straight and level track) and keep your CS #2 GP-9 on track while passing swiftly through curves.
Page 4
Lionel remote- Magnetic coupler on the rolling control track section (available separate- stock coupled to your CS #2 GP-9 ly).
CS #2 GP-9 is equipped with wheel sets and working their way Lionel Magne-Traction, magne- into the CS #2 GP-9’s motor assembly. tized wheelsets and axles that help They can damage your locomotive.
• Horn. an auto like horn sound every that’s the CS #2 GP-9 telling you its time—a Railsounds exclusive. Lionel Command reverse unit has just • Mechanical bell. Press BELL on your reset to forward operation. CAB-1 or transformer to begin the •...
(for bell) (for horn) The no. 610-5906-001 sound activation button (available separately) works with any Lionel AC transformer except no. 6-4690 Type MW. Note! Transformers made by other manufacturers may not be compatible with Railsounds.
• Make sure track power is OFF before placing your CS #2 GP-9 on the track. • Make sure your Lionel Command Base is ON and its communi- cations wire is connected to the COMMON post on your Lionel transformer or the U post on any of your installed PowerMasters.
Running your CS #2 GP-9 in the TrainMaster Command environment our Command-equipped CS #2 Example address Locomotive #1 GP-9 locomotive comes factory- programmed with an ID# of “1.” To PowerMasters set to CMD or traditional get your CS #2 GP-9 locomotive in power supplies ON FULL action, set PowerMasters to CMD or set all power supplies on full.
TrainMaster Command operations CAB-1 numeric keypad commands for your CS #2 GP-9 AUX1 like SW, ACC, RTE, TR, or ENG). hen you press AUX1 on The CAB-1 keypad overlay CAB-1, you turn the included with your CS #2 numeric keypad into 10 com- START-UP CREW GP-9 are designed to help...
To achieve your preferred Rail- Momentarily blipping the boost will sounds master volume level, use the also rev up your hot rod GP-9 volume control knob on the underside of the locomotive (see page 13 for its STALL location).
TrainMaster Command operations Assigning your locomotive a new ID# Assign a new I D# to your s your fleet of Command-equipped Example Command-equipped locomotive Lionels grows, give your CS #2 GP- Command Base ON 9 locomotive its own ID#. Choose from any between 1 and 99.
Maintaining and servicing your CS #2 GP-9 locomotive Lubricating your CS #2 GP-9 locomotive on the CS #2 GP-9’s wheels, contact elp your Lionel CS #2 GP-9 loco- rollers, or your track. motive lead a long and productive You’ll know your CS #2 GP-9...
Please avoid all physical con- screws (see illustration on page 13). tact with the R2LC. Apply a small amount of Lionel oil (two Lionel oil Reprogramming R2LC circuit boards to restore features ue to the inevitable derailments,...
Note! off, before replacing bulb Your Lionel CS#1 hot rod GP-9 is equipped with a roof mounted flashing strobe light, this small bulb (Lionel part no. 10-8205-009) is located inside the cab. During the course of normal operation it may Note! require replacement.
Website @ www.Lionel.com motors and structural components, except for If you prefer to send it back to Lionel L.L.C. for light bulbs, is warranted to the original con- factory repair, you must first call 810-949-4100 or...
Need help?
Do you have a question about the Hot Rod GP-9 and is the answer not in the manual?
Questions and answers