Related Manuals for Elan VHTO100
Summary of Contents for Elan VHTO100
- Page 1 VHTO100 HOME THEATER OVERRIDE MODULE VHTO100 INSTALLATION & APPLICATIONS MANUAL S Y S T E M S T M H O M E...
-
Page 3: Table Of Contents
Specifications ................2 VHTO100 to PZ6 Connections ..........3 VHTO100 to PZ600 Connections ........... 3 VHTO100 to Z•600 Connections (no PZ6 or PZ600) .... 4 Using the Z•600’s Internal Power Supply ......4 Using an External Power Supply w/PZ6 or PHD12 .... 5 Using an External Power Supply (no PZ6 or PZ600)..... -
Page 4: Introduction
Series MCU or a MAC24/AV-L2 whenever a Page or Door Chime is initiated-triggers AMP OR SPEAKERS a pair of relays on the VHTO100, switching the audio path from the local system amplifier to the ELAN system amplifer. VHTO100 In a Home Theater, ELAN Page and Door Chime audio can be routed to the rear channel speakers. -
Page 5: Vhto100 To Pz6 Connections
VHTO100 and connect the rear channel speaker outputs from the local amplifier to the SSP terminals on the VHTO100 as shown below. Connect the OR leads from any of the PZ6’s VC+ and VC- terminals to VC+ and VC- on the VHTO100. -
Page 6: Vhto100 To Z•600 Connections (No Pz6 Or Pz600)
Connect speaker cables from the ELAN system amp to the AMP terminals on the VHTO100 and connect the rear channel speaker outputs from the local amplifier to the SSP terminals on the VHTO100 as shown below. Tie together the Wh/Orange and Wh/Brown conductors from the Z•600’s Control Output Jack as shown. Connect the Control Output Jack’s Green conductor to VC- of the VHTO100 and connect Brown to... -
Page 7: Using An External Power Supply W/Pz6 Or Phd12
Tie the Z•600 Control Output Jack’s Blue conductor together with Wh/Blue. This will go to VC+ of the VHTO100. Tie Wh/Green to Brown and connect to the + on the power supply. Connect the - of the power supply to VC- on the VHTO100. -
Page 8: Vhto100 To Phd12 Connections
Speaker Outputs System Amplifier Rear Surround Speakers Local Amplifier (SSP) RELAY OUTPUTS AC/DC Relay N.O. 5A MAX Relay COM SENSE INPUTS +12VDC Power Supply HDC2042 SERIAL PORT Automation Card Page 6 © ELAN Home Systems 2005 • All rights reserved. -
Page 9: Vhto100 To Mac24 Connections
Connect speaker cables from the MAC24 to the AMP terminals on the VHTO100 and connect the rear channel speaker outputs from the local amplifier to the SSP terminals on the VHTO100 as shown below. Connect the OR leads from the MAC24’s O+ and O- terminals to VC+ and VC- on the VHTO100. -
Page 10: Override Jumper Settings
VHTO100 and pulling up the PC board/transformer assembly. There are no wires that need to be disconnected. The volume of ELAN Page and Door Chime audio can be adjusted by repositioning the Override Volume Jumpers (2). There are ten settings to choose from: 1 is the lowest, 10 is the highest (Factory Default: 5). -
Page 11: Creating A Pg/Db "Wide Coverage" Zone
In areas of a home where ELAN Page and Doorchime audio needs to be heard, but music is not necessary, the VHTO100 makes it easy to creat a "wide coverage" zone - as well as drastically reducing the cost of such a zone by eliminating the need for mul- tiple impedance matching volume controls with Override. -
Page 12: Limited Warranty
ELAN authorized installer, (c) to installed equipment which is not installed to ELAN's specifications, (d) to equipment which shall have been repaired or altered by others than ELAN, (e) to equipment which shall have been subjected to negligence, accident, or...