Elan IRD10 Manual

Limited Warranty

ELAN HOME SYSTEMS, L.L.C (ELAN) warrants this product to be free from defects
in materials and workmanship for five (5) years from date of purchase. If within the
warranty period purchaser discovers such item was not as warranted above and
promptly notifies ELAN in writing, ELAN shall repair or replace the items at the com-
pany's option. This warranty shall not apply (a) to equipment not manufactured by
ELAN, (b) to equipment which shall have been installed by other than an authorized
ELAN installer, (c) to installed equipment which is not installed to ELAN's specifica-
tions, (d) to equipment which shall have been repaired or altered by others than
ELAN, (e) to equipment which shall have been subjected to negligence, accident,
or damage by circumstances beyond ELAN's control, including, but not limited to,
lightning, flood, ,electrical surge, tornado, earthquake, or any other catastrophic
events beyond ELAN's control, or to improper operation, maintenance or storage,
or to other than normal use of service. With respect to equipment sold by, but not
manufactured by ELAN, the warranty obligations of ELAN shall in all respects con-
form and be limited to the warranty actually extended to ELAN by its supplier. The
foregoing warranties do not cover reimbursement for labor, transportation, removal,
installation, or other expenses which may be incurred in connection with repair or
replacement.
Except as may be expressly provided and authorized in writing by ELAN, ELAN
shall not be subject to any other obligations or liabilities whatsoever with respect to
equipment manufactured by ELAN or services rendered by ELAN.
THE FORGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER
EXPRESSED AND IMPLIED WARRANTIES EXCEPT WARRANTIES OF TITLE,
INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE.
2428 Palumbo Dr.
Lexington, KY 40509
(859) 269-7760
www.elanhomesystems.com
©2005 ELAN Home Systems P/N 224390 X2
4
Introduction
The IRD10 provides a quick and low cost means of expanding the num-
ber of emitters that can be driven from an ELAN multi-room controller or
IRD4 Amplified Connection Block. It is a passive expander that includes
current sharing resistors at each emitter jack allowing any combination
of single or dual emitters to be used. A HIGH IR LOOP OUT is provided
for daisy-chaining additional IRD10s so that even more emitters can be
driven (up to a maximum of 50 emitters).
IRD10
10 Port
IR Emitter
Expansion
Block
Top
EMITTER OUTPUTS
View
HIGH
IR IN
3-1/2"
(89mm)
Side
View
Peel-off Adhesive
Protective Cover
Features
• HIGH IR IN: 3.5mm jack accepts IR signals from High Power (HP ON
setting) port on the IRD4 Amplified Connection Block or other high
output source.
• EMITTER OUTPUTS: Ten 3.5mm jacks drive any selection of single or
dual emitters with current sharing resistors at medium power.
• HIGH IR LOOP OUT: 3.5mm jack allows High Power IR signals to be
looped to additional IRD10s for increased emitter expansion (up to 5
IRD10s, 50 emitters maximum).
• Adhesive Bottom Cover: Protects the bottom of the PCB and also
allows attachment of the IRD10 to any flat, dry, clean surface. Simply
peel-off the protective cover to expose the adhesive.
• 3.5mm Mono Extension Cable: 1 foot cable connects the IRD10 to the
IRD4 Amplified Connection Block and for looping to additional IRD10s.
IRD10
10 Port
IR Emitter
Expansion
Block
Fig. 1
HIGH IR
1-9/16"
(40mm)
LOOP
OUT
11/16"
1 Foot (305mm)
3.5mm Mono
(18mm)
Extension
Cable (included)
1