Troubleshooting Guide; Specifications - Kenwood KCA-BT100 Instruction Manual

Installation
Installation the Hands-free box
• Determine the installation position after making sure that
the unit can communicate with the cell-phone.
• Please do not install the unit near the dashboard, the rear
tray, or other important components. Doing so could
lead to injury or accident should the unit come off due to
a shock and strike a person or an important component.
Tapping screws should be used for mounting.
(Attachment with velcro strips, although easy, can come
off with a shock.)
Securing to audio board
Accessory 2 (ø5 × 20 mm)
Antenna part
Securing to pile carpet
Antenna part
Accessory 3
• Do not stick the Velcro tape over the serial number.
• If the installation place is stepped, cut the Velcro tape
into two pieces and stick them at two positions as
shown.
20
|
English
Installation the Microphone Unit
1
Check the installation position of the microphone
(accessory 1).
2
Remove oil and other dirt from the installation
surface.
3
Install the microphone.
4
Wire the microphone cable up to the hands-free
box with it secured at several positions using
tape or the like.
Fix a cable with a commercial
item of tape.
Peel the release coated paper of double-face adhesive tape
to fix on the place shown in the left-hand example.
Adjust the direction of the microphone to the driver.

Troubleshooting Guide

What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
General
?
The hands-free talk volume is low.
✔ The hands-free talk volume is set at a low level.
☞ The hands-free talk volume can be adjusted
independently. Adjust it during hands-free
talk.
?
No sound is heard from the rear speakers.
✔ You are talking in the hand-free talk mode.
☞ No sound is heard from the rear speakers in
the hands-free talk mode.
?
No beep is heard at reception of an incoming
call.
✔ No beep is heard depending on the type of your
cell-phone.
☞ Selecting "Call Beep: ON" or "C-BP ON" (page
11) allows you to hear the beep.
?
Characters in a name are missing.
✔ The control unit cannot display accent characters.
☞ Set the display character conversion function
switch to "2" (page 18).

Specifications

Specifications subject to change without notice.
Bluetooth section
Technology
: Compliant with Bluetooth ver.1.2
Maximum power
: 4 dBm (Power Class 2)
Maximum link distance
: 10 m (30 ft)
Profiles
: HFP (Hands Free Profile)
: OPP (Object Push Profile)
The messages shown below display your
systems condition.
No Number/ NO-NMBER/ Incoming No Number :
• The calling party does not notify a caller ID.
• There is no phone number data.
No Data/ NO DATA :
• There is no outgoing call list.
• There is no incoming call list.
No Entry/ NO ENTRY :
The cell-phone has not been registered (pairing).
Disconnect/ DISCONCT/ Non Connection :
The unit can communicate with the cell-phone.
Connect/ CONNECT/ Disconnected:
The unit cannot communicate with the cell-phone.
HF Error 07/ HF ERR07:
The memory cannot be accessed.
\ Turn off the power and on again. If this message still
appears, press the reset button on the control unit.
HF Error 68/ HF ERR68:
The unit cannot communicate with the cell-phone.
\ Turn off the power and on again. If this message still
appears, press the reset button on the control unit.
General
Operating voltage (11 – 16V allowable)
: 14.4 V
Current consumption
: ?? A
Dimension (W x H x D)
: 140 x 70 x 29 mm
5-1/2 x 2-3/4 x 1-1/8 inch
Weight
: 0.0 lbs (0.0 kg)
|
English
21