Cisco ASR 900 Series Configuration Manual page 60

Managing and Monitoring SONET Line
layer alarms counter
LOP = 0
LOM = 0
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
on the path.
Alarm reporting enabled for: PLOP LOM B3-TCA
TCA threshold:
Rx: C2 = 00
Tx: C2 = 02
PATH TRACE BUFFER : UNSTABLE
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
the path
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SONET Path Tables
INTERVAL
05:58-05:58
PATH 2:
Clock Source is internal
AIS = 0
LOP = 0
LOM = 0
Active Defects: None
Detected Alarms: None
Asserted/Active Alarms: None
Alarm reporting enabled for: PLOP LOM B3-TCA
TCA threshold:
Rx: C2 = 00
Tx: C2 = 00
PATH TRACE BUFFER : UNSTABLE
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SONET/SDH Path Tables
INTERVAL
05:58-05:58
OC3.STS1 0/3/3.1 is up.
Hardware is asr 900
Applique type is VT1.5
STS-1 1, VTG 1, T1 1 (VT1.5 1/1/1) is down
VT Receiver has no alarm.
Receiver is getting AIS.
Framing is unframed, Clock Source is Internal
t1
Data in current interval (0 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs
0 Unavail Secs, 0 Stuffed Secs
STS-1 1, VTG 1, T1 2 (VT1.5 1/1/2) is down
VT Receiver has no alarm.
Receiver is getting AIS.
1-Port OC-192 or 8-Port Low Rate CEM Interface Module Configuration Guide, Cisco IOS XE Everest 16.7.x
(Cisco ASR 900 Series)
46
PSE = 0 NSE = 0
PLM = 0 UNEQ = 0
B3 = 10e-6
CV ES SES UAS
0 0 0 0
RDI = 0 REI = 0
PSE = 0 NSE = 0
PLM = 0 UNEQ = 0
B3 = 10e-6
CV ES SES UAS
0 0 0 0
======> present status of the path
=====> mode of the path
NEWPTR = 0
======> present alarms
=====> rx and tx C2 byte..
................
................
................
................
BIP(B3) = 0
NEWPTR = 0
................
................
................
................
====> status of the SPE (t1)
===> alarm of the SPE (t1)
=====> framing of the T1, clock of the
Configuring SONET
====> path trace of