Table of Contents
Advertisement
Insert the injector feed and draw tubes into the main body, bottoming them out in their bores. Install the injector screen in the
regenerant body, the small hole in the end of the screen will nest around a feature in the plastic body allowing the large end to be flush
with a step in the tube bore. Confirm the placement of the o-ring on the ~2" diameter flange of the plastic body then press the
regenerant body straight onto the main body, assuring the o-rings engages the bore in the main body. Install & tighten the (4)1/4-20
screws. The lower injector o-ring engages the ID of the injector tube which may push the injector out of position when reinstalling the
regenerant body. Verify the injector is seated all the way down into its bore.
ITEM NO.
ORDER NO.
1
109530
2
109531
3
109532
4
102457
Order No.
5
109533
1
V3967
6
101375
2
V3441
3
V3968
7
102159
4
V3177-01
8
See Chart
5
V3969
6
V3176
101811
7
V3152
101812
8
V3010-15(Add Part #) WS 1 1/2 Injector
9
V3498
101813
10
V3428
101814
11
V3163
12
H4612
101815
13
JCPG-8PBLK
101816
14
JCP-P-8
V3182
TBD
15
16
H4615
9
103588
17
V3724
9b
101619
18
V3642
19
V3195-01
10
102417
11
102153
12
H4612
13
102129
14
101869
15
102421
16
101414
17
109534
18
109535
19
102322
102318
A 109532 Injector Feed Tube Assembly contains one O-ring-111 and two O-rings-112's.
An Injector Draw Tube Assembly contains one O-ring-113 and two O-rings-115's.
28
DESCRIPTION
H151 Injector Body, Welded Assy
O-Ring-226
H151 Injector Feed Tube
H151 Injector Screen
Description
H151 Injector Draw Tube
WS1.5 Injector Body, Welded Assembly
H151 Injector Cap
O-ring -226
WS1.5 Injector Feed Tube
O-Ring-135
WS1 Injector Screen
H151 1-1/2 Injector
WS1.5 Injector Draw Tube
WS1 Injector Cap
C - Red
O-ring -135
D - White
Refill Flow Control, 1/2"
E - Blue
WS 1.5 Refill Retainer Assembly (0.5 GPM)
F - Yellow
O-ring, -019
Elbow Cap, 1/2"
G - Green
Nut, Compression, 1/2" Black
H - Orange
Insert, Polytube 1/2"
Refill Flow Control (0.5 GPM)
I - TBD
Retaining Clip
Refill Flow Control, 1/2"
Washer, Flat Stainless Steel
3/4" Refill Elbow (H151-450 Only)
Bolt, BHCS Stainless Steel 1/4-20x 1 1/4
BLFC on Brine Tank
Refill Port Plug
H151 Refill Retainer Assy (0.5GPM)
O-Ring-019
Elbow Cap, 1/2" (See #9)
Nut, Compression, 1/2" Black (See #9)
Insert, Polytube 1/2" (See #9)
Refill Flow Control
Retaining Clip
Washer, Flat Stainless Steel
Bolt, Stainless Steel 1/4-20x1-1/4
Refill Plug Port
Plug - Black
REGENERANT BODY
QTY
1
1
1
1
Quantity
1
14
1
1
1
1
1
1
1
1
1
1
1
13
1
1
1
1
16
1
1
1
17
1
1
4
4
18
1
1
1
1
1
1
1
1
4
4
1
1
Proper RFC orientation
directs refill water flow
towards the washer face
with rounded edges
9
15
11
10
12
7
8
6
19
2
4
3
5
1
Advertisement
Table of Contents
