GE D30 Instruction Manual page 383

CHAPTER 5: SETTINGS
Operand type Operand syntax
ELEMENT: TELEPRO CH1 FAIL
Teleprotection TELEPRO CH2 FAIL
channel tests TELEPRO CH1 ID FAIL
TELEPRO CH2 ID FAIL
TELEPRO CH1 CRC FAIL
TELEPRO CH2 CRC FAIL
TELEPRO CH1 PKT LOST
TELEPRO CH2 PKT LOST
ELEMENT: TELEPRO INPUT 1-1 On
Teleprotection ↓
inputs/outputs TELEPRO INPUT 1-16 On
TELEPRO INPUT 2-1 On
↓
TELEPRO INPUT 2-16 On
ELEMENT: THERMAL PROT 1 PKP
Thermal overload THERMAL PROT 1 OP
protection
THERMAL PROT 2
ELEMENT: TRIP BUS 1 PKP
Trip bus TRIP BUS 1 OP
TRIP BUS 2 to 6
ELEMENT: UNDERFREQ 1 PKP
Underfrequency UNDERFREQ 1 OP
UNDERFREQ 1 DPO
UNDERFREQ 2 to 6
ELEMENT: WATTMETRIC 1 PKP
Wattmetric zero- WATTMETRIC 1 OP
sequence directional
WATTMETRIC 2
FIXED OPERANDS Off
On
INPUTS/OUTPUTS: Cont Ip 1 On
Contact inputs Cont Ip 2 On
↓
Cont Ip 1 Off
Cont Ip 2 Off
↓
Cont Ip 120 On
Cont Ip 120 Off
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2
current ↓
(from detector on Cont Op 72
form-A output only)
INPUTS/OUTPUTS: Cont Op 1 VOn
Contact outputs, Cont Op 2
voltage ↓
(from detector on Cont Op 72
form-A output only)
Cont Op 1
Cont Op 2
↓
Cont Op 72
INPUTS/OUTPUTS: DIRECT INPUT 1 On
↓
Direct inputs
DIRECT INPUT 32 On
INPUTS/OUTPUTS: RxG DPS 1 BAD
RxGOOSE DPS RxG DPS 1 INTERM
RxG DPS 1 OFF
RxG DPS 1 ON
D30 LINE DISTANCE PROTECTION SYSTEM – INSTRUCTION MANUAL
Operand description
Channel 1 failed
Channel 2 failed
The ID check for a peer relay on channel 1 has failed
The ID check for a peer relay on channel 2 has failed
CRC detected packet corruption on channel 1
CRC detected packet corruption on channel 2
CRC detected lost packet on channel 1
CRC detected lost packet on channel 2
Flag is set, Logic =1
↓
Flag is set, Logic =1
Flag is set, Logic =1
↓
Flag is set, Logic =1
Thermal overload protection 1 picked up
Thermal overload protection 1 operated
Same set of operands as shown for THERMAL PROT 1
Asserted when the trip bus 1 element picks up
Asserted when the trip bus 1 element operates
Same set of operands as shown for TRIP BUS 1
Underfrequency 1 has picked up
Underfrequency 1 has operated
Underfrequency 1 has dropped out
Same set of operands as shown for UNDERFREQ 1
Wattmetric directional element 1 has picked up
Wattmetric directional element 1 has operated
Same set of operands as per WATTMETRIC 1
Logic = 0. Does nothing and can be used as a delimiter in an equation list;
used as 'Disable' by other features.
Logic = 1. Can be used as a test setting.
(does not appear unless ordered)
(does not appear unless ordered)
↓
(does not appear unless ordered)
(does not appear unless ordered)
↓
(does not appear unless ordered)
(does not appear unless ordered)
IOn (does not appear unless ordered)
IOn (does not appear unless ordered)
↓
IOn (does not appear unless ordered)
(does not appear unless ordered)
VOn (does not appear unless ordered)
↓
VOn (does not appear unless ordered)
VOff (does not appear unless ordered)
VOff (does not appear unless ordered)
↓
VOff (does not appear unless ordered)
Flag is set, logic=1
↓
Flag is set, logic=1
Asserted while the RxGOOSE double-point status input is in the bad state
Asserted while the RxGOOSE double-point status input is in the intermediate
state
Asserted while the RxGOOSE double-point status input is off
Asserted while the RxGOOSE double-point status input is on
FLEXLOGIC
5
5-173