Table of Contents
Advertisement
LCD WITH BUILT-IN DVR USER MANUAL
3.3.2 CHANNEL SETU P
Channel setup
setting includes
channel
TV screen cover, etc
CH
Title
1
2
3
4
a).
Channel: Enter the channel number.
it indicates invalid channel.
Note:
For each channel,
it means the
channel
image under monitoring if the channel has image signal. But, the system will not prompt
the alarm message if the image signal of this TV screen has lost.
b).
Title
: Name of the
channel. Enter the title of the camera location.
and press enter and
enter the channel title.
c). Screen Display: Two choices are switch on or switch off. If
channel title
while
monitoring. If selecting
monitoring.
d). Time Insert: There are three choices for users, up, down or close. Press Enter to make your selection.
When option up is selected, the time will be displayed on top of the screen, when option Down is
selected, the time will be displayed at the bottom of the screen. If the option Closed is selected,
the time will not be displayed on the screen.
e).
Mask:
Two choices for users are switch on or switch off. You can press enter for any changes.
TV
mask used
for covering the
f).
Channel View:
Two choices for users are open or close.
and close blocks the image from viewing.
3.3.3 Alarm Setting
a).
Terminal:
1, 2, 3,
4 respectively represent 4 outer I/O alarm input ports.
Open：
b).
Two choices are open or close. Open indicates the system has received the input alarm signals
from the I/O end points. Close indicates the system has not received the input alarm signals.
C).
inputting way:
Two choices are（close/short）closed circuit and open circuit.
option to turn on /off alarm for each channel
d).
Delay alarm recording:
Under the alarm recording condition, the system receives the alarm signal
from I/O. The system recording video is according to the time length which the user has already
set up. The system will stop recording video automatically when it has reached the end of its set time
since it has not received the alarm signal from the new I/O.
PDF created with pdfFactory trial version
name, screen display, clock insert,
Channel Setup
CH Name
Time InSert
Mask
CH View
Open
Down
Close
Open
Open
Down
Close
Open
Open
Down
Close
Open
Open
Down
Close
Open
Return
If it has a X symbol in front of the channel number code,
channel
can't record video. However, you can still see the
Move the
cursor
When you have finished, press enter.
switch on is selected
switch
off, it will not show channel title
part of channel which is not to be recorded.
Open keeps the channel open for viewing
-e13-
www.pdffactory.com
LCD WITH BUILT-IN DVR USER MANUAL
3. 2 System on/off
3. 2.1 Sy stem Start
When supplying power to DVR normally, the system enters into stand-by state（the indicating
light of the power－red led is on permanently）。
When press the【on/off】button in the remote control unit，the system is started，pictures
displayed in the screen are built-in quad images，the digit showed in each picture means its video
input channel No. the real time will be displayed at the top
Note:
If time recording
and power is just connected during this period, then the machine will start and enter
into multi-pictures state directly without needing to press【on/off】button again to start
the machine.
If there
system, please press【ENTER】 button
numbers will be displayed on the screen
If the hard disc has not been installed before turning on the machine, or the hard disc is not
detected by the machine after turning it on, the monitor with hard disc will set off the alarm,
Please log in the system to turn off the alarm.
3. 2.2 Sy stem Login
to this topic
：
Note:
, it will show the
while
When the host machine is started，user can only operate the system when
no activity within 100 seconds after logging in, the system will enter into lock state!
When the machine is just started or under lock up state, press the
Remote Control Unit，the login interface in the screen will appear, type in the code of the
machine（Pre-delivery setup： 000 ），and then type in the password（password for
administrator or operator of this machine）.
⑴ If correct user's password is typed in，the monitor will show Password Correct message on
the screen, and then after [Return] for confirmation，users can operate each items within
the permitted field(the default password for user is：00000000）.
⑵ If correct administrator's password is typed in，
message on
all
the operations in the machine（The default password for administrator is：88888888）。
Users have the
Note：
has been setup in this machine(or at high peak period)，
is
no display of video input channel No in the screen and the real time for the
on
the remote control unit or panel,
P
re-delivery code for this equipment is：000，the default password for
administrator is 88888888，and it is 00000000 for user. Administrator
has all
the
operating rights. In order to make sure the safe running of the
system, administrators should change its code and default password of the
machine
immediately.
''
''
the monitor
the screen，and then after [Return] for confirmation，administrator can
There are two password management- one for administrator and another for user,
different operating range will be permitted by inputting different password.
-e10-
center
of the screen.
and the channel
logged in
.
If there is
【Login/Lock】
Button on
''
''
will show Password Correct
''
''
perform
Advertisement
Table of Contents
