Q-See QT17DVR4C User Manual page 10

LCD WITH BUILT-IN DVR USER MANUAL LCD WITH BUILT-IN DVR USER MANUAL
3.3.5 Housing setting
Moving cursor upon [Pan/Tilt setting] and pressing [ENTER] key can enter into quad channel
Pan/Tilt port setting interface
A. Channel: Denotes system's channel number.
B. Protocol: Denotes the communication protocol between system and decoder. Moving cursor
to this selection item and pressing [ENTER] key can make selection among different protocol
(Pe1co-D/P/09-15/Dscp/FastDome/PIH1016-1017/JECFastD/RM110/Neocam) Selected
protocol must match to the protocol of decoder, only can it control front equipment correctly.
C. Baud rate: Denotes communication speed between system and decoder. Moving cursor to this
item selection and pressing [ENTER] key can make selection among different baud rate
(1200/2400/4800/9600), selected baud rate must match decoder's baud rate, only can it control
front equipment correctly.
D. Pan/Tilt code: Moving cursor upon this selection item and pressing [ENTER] can make
selection among different Pan/Tilt serial number (01-63), system's 01 code number match
to decoder's first address code, that is address code "01"
E. After
setting up all item selection, move cursor to [RETURN] and press [ENTER] key will
return toprevious menu, and save Pan/Tilt parameter setting.
Attention: Pan/Tilt protocol, baud rate, Pan/Tilt serial number three items must be
accordance with outer Pan/Tilt (quick ball) setting parameter.
Pan /Tilt operation: After setting Pan/Tilt parameter correctly, press [F2] key
control under single monitoring state, the top left corner of screen will display "Pan/Tilt control"
character, temporarily, we can operate this channel's Pan/Tilt by using press
control and panel.
【 】、【 】 Key:
Lens up and down motion, display character: up and down;
【 】、【 】 Key: Lens left and right motion, display character: Pan/Tilt left and right;
【 Change times + 】、【 Change time - Key:
Change times + and change times -;
【 Aperture + 】、【 Aperture - Key:
Aperture + and aperture -;
【 】、【 】
Focus + Focus - Key:
【 Automatic Key: 】
signifies automatic control, display character: Automatic
【 】
Transfer Key: Pan/Tilt transfer control, display character: transfer 00, back key;
【 Pre-set Key: 】
Pan/Tilt preset control, display character: preset 00, back key.
【 】
Washer switch/Light Key:
Washer switch;
Pressing [F2] and [Pan/Tilt] once more will exit Pan/Tilt operation, and return to single image
monitoring state; Switch monitoring image and pressing [F2] key can enter into another channel
Pan/Tilt operation.
Warning 1:
When operating Pan/Tilt function, system can't startup manual video recording
function.
Warning 2: When operating Pan/Tilt function, once system startup video record (timing or
alarm startup), temporarily can't affect Pan/Tilt operation.
Troubleshooting: When Pan/Tilt doesn't operate normally, Please check RS-485 (see "Alarm
Port lead line definition") and Pan/Tilt parameter
PDF created with pdfFactory trial version
】 Adjust image far and near extent, display character:
】 Adjust image bright and dark extent, display character:
Adjust image clarity extent, display character: Focus + and focus -;
Washer switch and light assistant switch control, display character:
-e15-
www.pdffactory.com
LCD WITH BUILT-IN DVR USER MANUAL LCD WITH BUILT-IN DVR USER MANUAL
3. 1.2 Re mote Control Unit
Buttons
Digital Buttons Area
①
【0-9】Button：
in
【+】、【-】Button：
Menu Operating Buttons Area
②
on remote
：
： DOWN Directional button;
[F2] key on remote ：
： RIGHT Directional button;
【ENTER】button：
③ Platform control function buttons
【ZOOM+】、【ZOOM-】Button：
【APERTURE+】、【APERTURE-】Button：
【FOCUS+】、【FOCUS-】Button：
【AUTO】Button：
【RECALL】Button：
【PRESET】Button：
【SWITCH】Button：
Play function buttons
④
【PLAY】Button：
【SLOW】Button：
【PAUSE/SETP】Button：
【FWD】Button：
【REV】Button：
L O GIN/ L OCK
PL AYBA C K
QUAD
P A RAMET E R
ANAL O G
ZOOM +
FO CUS+
AU TO
REC ALL P R ESET
PLAY SLOW
F WD REV
R ECOR D ST OP
F1 F1
on Remote Control Unit and their functions:
Digital buttons，used for using digit input or video switch，when under the
built-in quad state, press 1、2、3、4 digit buttons mean to switch the picture
output to the first, second, third and forth channel video single picture；
Adjusting various parameters；
UP Directional button;
LEFT Directional button;
for confirmation，choosing the menu items, and press this button to enter
into the selected sub-menu；Pressing this button can display the real time
of the system when playing back the recording
Adjust the distance of the picture；
Adjust the brightness of the picture；
Adjust the sharpness of the picture；
Control automatically；
standby button in control of platform；
Preset control on platform, standby button；
control on some assistant switch；
Play the the recording on the hard drive
Play the images slowly，at speed of ×1/2、×1/4、×1/8 times，or press
【play】 button to return to normal playing speed；
Press one time to Pause the picture ,and then press continuously,
picture will be displayed frame by frame, press
return to normal speed of playing.
Play fast forward of the playback picture，at the speed of×2、×4 times，press
【Play】
Button to return to the normal speed of playing；
Play fast backward of the playback pictures， at speed of×2、×4 times，press
【Play】 Button to return the normal speed of playing；
-e8-
PO WE R ON
1 1 2 2 3 3
4 4 5 5 6 6
7 7 8 8 9 9
+ +
0 0
ZO OM-
FO CUS-
EXIT
SW ITC H
CF
NET
SE T UP
F 2 F3 F4
；
；
【 Play 】 button to