Table of Contents
Advertisement
10. Relay Mode
NOTE: The 40-IP does not have a built-In relay. If relay control is required, an optional RC-4A relay controller can be used with the
40-IP.
Doorstrike Mode: When programmed for Doorstrike Mode the relay is intended for door strike, maglock or gate control.
Ring Mode: When programmed for Ring Mode the relay will continuously activate while the ringing extension is called. This mode
is useful for activating a Viking model SL-2 strobe light, etc.
Ring Flash Mode: When programmed for Ring Flash Mode the relay will momentarily turn on and off in a 400ms on/off cadence
while the ringing extension is called. This mode is useful for activating a Viking LPL-1 Remote Visual Indicator, etc.
Paging Mode: When programmed for Paging Mode the relay will activate continuously for the duration of any inbound or outbound
call to or from the Speaker phone. This mode is useful for turning on IR flood lights, for VoIP phones with cameras, etc. It also
activates on a Multicast page.
11. Relay Activation Command
The one or two digit code stored in the Relay Activation Command is the touch tone command that the person being called must
enter on their phone in order to momentarily activate the RC-4A relay to control a doorstrike, mag-lock, gate controller, or other
device. The code can contain the characters 0 - 9, # or Q. The code cannot match a relay latching or toggle command (Q1, Q0). The
code must be entered (after the access code is enabled) while the remote phone is communicating with the Speaker phone. The
factory setting is QQ. NOTE: If the access code is programmed it must be entered before controlling relays. If this security is not
needed, leave the access code blank.
12. Relay Activation Time
The value stored in the Relay Activation Time is the amount of time the RC-4A relay will be energized after a correct momentary
touch tone command is entered. This number can range from 0.5 to 99 seconds. The factory setting is 5 seconds. This also affects
timing in Doorbell Mode.
13. Relay Buzz Volume
The relay activation tone is a buzzing sound that is heard from the speaker when the door strike relay is activated.
After the called party enters the correct relay activation command, the called party will hear 2 short confirmation beeps
and the entry phone will output a buzzing sound (relay activation tone) while the door strike relay is activated. The tone
(buzz) length will match the relay activation time up to a maximum of 5 seconds. The tone (buzz) can be programmed
to three different volume settings 1 = Low, 2 = Medium, 3 = High or it can be disabled.
14. Relay Latch Commands
When set to "Enabled" (factory default) the Remote Access Operation Commands (Q0 to Q1) to Un-Latch or Latch the relay are
enabled. These can be entered on a Inbound call after the access code is dialed (if programmed).
When set to "Disabled" the Remote Access Operation Commands (Q0 to Q1) to Un-Latch or Latch the relay are disabled. Disabling
the Latch commands can be useful in applications where you want to eliminate the possibility of inadvertently entering a latch
command leaving a gate open/closed, etc. Momentary relay activation commands are still allowed.
15. SIP Paging Volume
The SIP Paging Volume can be set from 0-9, factory set to 1. 0 = lowest volume setting, 9= highest volume setting.
Adjusting this will set the volume level for SIP Paging.
16. Ring Volume
When set to Ring the 40-IP will output a loud ring when it is called. The level can be adjusted from 0-9. Factory set to 5.
17. SIP Page Length Time Out
This feature selects the maximum length of time that SIP Page calls can be connected. Programmable in increments
of 1 minute up to a maximum of 9 minutes or disabled. With the call length disabled, the 40-IP phone must rely on a call
ended signal or touch tone # to hang-up.
Note: The factory default is 3 minutes.
13
Advertisement
Table of Contents
