Download
Share
Print this page
  1. Manuals
  2. Brands
  3. 3Com Manuals
  4. Control Unit
  5. WL-463
  6. Installation manual

3Com WL-463 Installation Manual

802.11g mini-pci radio module
Hide thumbs Also See for WL-463:
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual See also: User Manual
802.11g mini-PCI Radio Module
MODEL WL-463
The 3Com 802.11g mini-PCI Radio Module kit contains everything you need to install an additional radio and
antenna into your 3Com Access Point.
Kit Contents
The upgrade kit contains these items:
one antenna module
•
one 802.11g mini-PCI Radio Module
•
two cables
•
two antennas
•
1
Detach and disconnect the access point.
If the access point is mounted on the wall, turn the unit counterclockwise to disengage it from the mounting
plate. Disconnect the Ethernet cable. Place the access point face down on a static-free surface.
Installation Guide

Advertisement

loading

Related Manuals for 3Com WL-463

Summary of Contents for 3Com WL-463

  • Page 1 Installation Guide 802.11g mini-PCI Radio Module MODEL WL-463 The 3Com 802.11g mini-PCI Radio Module kit contains everything you need to install an additional radio and antenna into your 3Com Access Point. Kit Contents The upgrade kit contains these items: one antenna module •...

  • Page 2: Remove The Back Cover

    Remove the back cover. Using a cross-tip screwdriver, remove the four screws from the back cover. Remove the cover from the unit. Set the cover and screws aside.
  • Page 3 Remove the antenna housing. Grasp the inside edge of the antenna housing and pull up to disengage the housing from the unit, as shown below. This part is no longer needed. Install the radio board. Holding the radio board at an angle, align the contact edge with the mini PCI connector on the unit. Make sure the keying notch on the contact edge lines up with the key on the connector, as shown in the detail below.
  • Page 4 Attach the cables to the antenna module. With the notched side of the square connector facing up (button side facing down), insert one cable connector into the B1 connection on the antenna module and push gently until it snaps into place. Attach the other cable connector to the B2 connection in the same manner.

  • Page 5: Attach The Antennas

    Replace the back cover. Make sure that the cables are tucked away inside the housing so that they do not obstruct the cover. Align the back cover with the unit and settle the cover into place. Tighten the four screws. Attach the antennas.
  • Page 6 SELECTING AND CONNECTING A DIFFERENT ANTENNA MODEL The standard detachable antennas supplied with the WL-463 11g mimi-PCI radio module and are suitable for a broad variety of environments. If you require a different type of antenna several options are available by model number from the 3Com Web site (www.3Com.com).
  • Page 7 POWER SETTINGS ON THE ACCESS POINT FOR EXTERNAL ANTENNAS USA/CANADA 2.5dBi 4dBi 8dBi (3CWE492) (3CWE490, (3CWE491, 3CWE497) 3CWE498) 6 ft (3CWE480) 20ft (3CWE481) 50 ft (3CWE482)

  • Page 8: Regulatory Compliance Information

    20 centimeters. This product does not contain any user serviceable components. Any unauthorized product changes or modifications will invalidate 3Com’s warranty and all applicable regulatory certifications and approvals. This product must be installed by a professional technician/installer.
  • Page 9 • Copyright © 2004 3Com Corporation. All rights reserved. 3Com, and the 3Com Logo are registered trademarks of 3Com Corporation. All other company and product names may be trademarks of the respective companies with which they are associated. 09-2330-000 Rev AA...