Table of Contents
Advertisement
SPECIFICATIONS
Voltage
Power input
No-load speed
Drill chuck capacity
Capacity
Weight (without cord)
STANDARD ACCESSORIES
(1) Side handle ................................................................. 1
(2) Stopper ........................................................................ 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
(1) Hook
(2) Plastic case
Optional accessories are subject to change without notice.
APPLICATIONS
Boring holes in metal, wood and plastic.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, inviting serious accident.
3. Extension cord
When the work area is removed from the power
source. Use an extension cord of sufficient thickness
and rated capacity. The extension cord should be kept
as short as practicable.
4. Selecting the appropriate drill bit:
When boring metal or plastic
Use ordinary metalworking drill bits.
When boring wood
Use ordinary woodworking drill bits.
However, when drilling 6.5 mm or smaller holes, use
a metalworking drill bit.
5. Mounting and dismounting of the bit (Fig. 1)
(1) Open the chuck jaws, and insert the bit into the chuck.
To open the chuck jaws, hold the ring while turning
the sleeve in the counterclockwise direction (viewed
from the front side).
(2) Firmly grasp the ring and turn the sleeve in the
clockwise direction. Tighten securely.
(3) To remove the bit, firmly grasp the ring and turn the
sleeve in the counterclockwise direction.
4
Steel
Wood
110V
500 W
1700/min
10 mm
10 mm
25 mm
1.6 kg
6. Side handle attachment (Fig. 2)
Attach the side handle to the mounting part.
Rotate the side handle grip in a clockwise direction to
secure it.
Set the side handle to a position that is suited to the
operation and then securely tighten the side handle
grip.
7. Check the rotational direction (Fig. 3)
The bit rotates clockwise (viewed from the rear side)
by pushing the R-side of the push button.
The L-side of the push button is pushed to turn the bit
counterclockwise.
(The
and
marks are provided on the body.)
8. Install the stopper (Fig. 4)
(1) Loosen the side handle and insert the straight portion
of the stopper into the handle bolt hole.
(2) Move the stopper to the specified position and rotate
the grip of the side handle clockwise to fix the stopper.
9. Installing the hook (optional accessory) (Fig. 5)
(1) Insert the hook into the hole of Section A on the main
body and turn it clockwise.
When the nut reaches the washer surface of the handle
cover, tighten it with a wrench.
(2) It is also possible to install the hook on the opposite
side. To do so, follow the same procedures mentioned
above.
(3) It is possible to hang the hook on a waist belt or a
pipe up to maximum 28 mm in diameter, and so on.
CAUTION:
When the power tool is used with a hook fixed to it, pay
attention to the following points:
Before hanging the main unit from the waist belt,
make sure that the drill has come to a complete stop.
While it is suspended from the waist belt, the power
plug must be disconnected from the power source.
Do not walk about with the power tool hanging from
the waist belt.
In the case of operation in a high place, it is
dangerous to drop the tool accidentally. If the hook
is deformed or hung from the wrong position, there
is danger that the hook will slip off and the tool will
fall.
Be careful to avoid danger.
In making a through hole, the power tool sometimes
shakes violently when the workpiece is pierced, from
example. Be careful you are not hurt by the hook
even if such situation happens.
50/60 Hz
Advertisement
Table of Contents
