Related Manuals for NEC MultiSync EX341R
Summary of Contents for NEC MultiSync EX341R
- Page 1 Desktop Monitor MultiSync EX341R User’s Manual Please fi nd your model name in the label on the backside of monitor.
-
Page 2: Table Of Contents
Index Warning, Caution ..........................English-1 Registration Information .......................English-2 Recommended use ........................English-3 Safety Precautions and Maintenance ..................English-3 Ergonomics ..........................English-4 Cleaning the LCD Panel .......................English-4 Cleaning the Cabinet ......................English-4 Contents ............................English-5 Quick Start ............................English-5 ControlSync ..........................English-10 Multiple monitors connection using DisplayPort ................English-12 Controls ............................English-13 Specifi... -
Page 3: Warning, Caution
This product can only be serviced in the country where it was purchased. Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K. -
Page 4: Registration Information
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. U.S. Responsible Party: NEC Display Solutions of America, Inc. Address: 500 Park Boulevard, Suite 1100 Itasca, Illinois 60143 Tel. -
Page 5: Recommended Use
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. -
Page 6: Ergonomics
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance of the monitor, allow 20 minutes for warming up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen. -
Page 7: Contents
Contents For contents, please refer to the contents sheet. Quick Start To connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” (page 3) before installation. The accessories included will depend on the where the LCD monitor is to be shipped. Do not hold Tilt cover. - Page 8 4. Connect all cables to the appropriate connectors (Figure C.1). When using the USB cable, connect the B type connector to the USB upstream port on the right back side of the monitor and the A type connector to the downstream port on the computer (Figure C.1a).
-
Page 9: Raise And Lower Monitor Screen
8. Turn on the computer and the monitor by touching the power button on the front bezel (Figure E.1). NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual. Power key Figure E.1 Raise and Lower Monitor Screen The monitor may be raised or lowered in landscape mode. -
Page 10: Flexible Arm Installation
Flexible Arm Installation This LCD monitor is designed for use with a fl exible arm. To prepare the monitor for alternate mounting purposes: • Follow the instructions provided by the manufacturer of the display mount. • To meet the safety requirements, the mounting stand must be able to support the weight of the monitor and be UL-certifi ed. * Contact your dealer for more information. - Page 11 Mount Flexible Arm This LCD monitor is designed for use with a fl exible arm. 1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand. 2. Use the 4 screws removed from the stand or the specifi ed screws to attach the arm to the monitor (Figure F.1). Caution: Use ONLY the screws (4 pcs) that were removed from the stand or the specifi...
-
Page 12: Controlsync
ControlSync ControlSync works controlling all connected sub monitors from master monitor simultaneously but also controlling a target monitor from master monitor by setting INDIVIDUAL ADJUST function (see page 21). Controlling all connected sub monitor (Synchronized control): 1. Connect the master monitor with a sub monitor via a ControlSync cable (ø 2.5) into ControlSync IN/OUT. 2. - Page 13 The following settings can be controlled by ControlSync: Synchronized control Individual adjust ECO TOOLS BRIGHTNESS* CONTRAST ECO MODE AUTO BRIGHTNESS BLACK LEVEL OFF MODE SETTING OFF MODE SENSOR SETTING OFF MODE START TIME HUMAN SENSING HUMAN SENSOR SETTING HUMAN SENSOR START TIME DV MODE SCREEN LEFT/RIGHT...
-
Page 14: Multiple Monitors Connection Using Displayport
Multiple monitors connection using DisplayPort You can connect multiple monitors by using DisplayPort daisy-chain connection. For using as multiple monitors in MST (multi-stream transport) mode, setting should be DP OUT MULTISTREAM “AUTO” at each connected monitor. Please change the monitor setting which is connected to a computer last in the connected monitors. If monitors have no image, turn off the monitor who is connected to a computer then turn it on. -
Page 15: Controls
Controls OSD (On-Screen Display) control keys on the front of the monitor function are as follows: To access OSD menu, touch any of the control keys. To change signal input, touch the INPUT/SELECT key. NOTE: Exit OSD in order to change signal input. 1 Ambient Light Sensor Detects the level of ambient lighting and the presence of a user, allowing the monitor to Human Sensor... -
Page 16: Eco Mode
ECO TOOLS BRIGHTNESS Adjusts the overall image and background screen brightness. If ECO MODE is set to 1 or 2, a bar for CARBON FOOTPRINT will appear. CONTRAST Adjusts the overall image and background screen brightness by input signal level. NOTE: CONTRAST and DV MODE can be adjusted when other than L/B is selected for COLOR CONTROL. - Page 17 HUMAN SENSING The sensor detects the movement of a person by using the HUMAN SENSING function. The HUMAN SENSING has three settings: OFF: No human sensing. 1 (LIGHT): After it is detected that there is no person after a period of time, the monitor shifts to low brightness mode automatically to reduce the power consumption.
- Page 18 OVER SCAN (HDMI input only) Some video formats may require different scanning modes in order to best display the image. 1: Image size is larger than what can be displayed. The image edge will appear cropped. Approximately 95% of the image will be shown on the screen.
-
Page 19: Picture Size
VIDEO DETECT Selects the method of video detection when more than one video inputs are connected. FIRST: When current video input signal is not present, then the monitor searches for a video signal from the other video input ports. If the video signal is present in another port, then the monitor switches the video source input port to the new found video source automatically. -
Page 20: Picture Position
PICTURE POSITION Determines where the sub screen appears on the screen. Press SELECT key for entering PICTURE POSITION mode (Figure 1). Using LEFT, RIGHT, UP and DOWN keys, controls the horizontal and vertical position of the sub screen within a half of the monitor that the sub screen is (Figure 2). -
Page 21: Menu Tools
MENU Tools LANGUAGE Selects the language used by the OSD. OSD TURN OFF The OSD menu will stay on as long as it is in use. You can select how long the monitor waits after the last touch of a key to shut off the OSD menu. -
Page 22: Multi Display
MULTI DISPLAY H MONITOR Selects the number of horizontal displays. V MONITOR Selects the number of vertical displays. MONITOR NO. This function is for image expansion with multi screen but also used for INDIVIDUAL ADJUST. Image expansion with multi screen: To set monitor number to each monitors, please refer to Example of installation and monitor number. -
Page 23: Eco Information
TILE MATRIX ENABLE Allows one image to be displayed over multiple screens. This feature can be used with up to 25 monitors (5 vertical and 5 horizontal). Using TILE MATRIX ENABLE requires the PC output signal be sent through a distribution amplifi er to each individual monitor. -
Page 24: Specifi Cations
@ 60 Hz 2560 x 1080* @ 60 Hz 2560 x 1440* @ 60 Hz 3440 x 1440 @ 30 Hz to 60 Hz......NEC DISPLAY SOLUTIONS cites recommended. Active Display Area Landscape: Horiz.: 797.22 mm/31.4 inches Vert.: 333.72 mm/13.1 inches Portrait: Horiz.:... -
Page 25: Features
- conversion factor is based on OECD publication of global CO2 emissions 2008 Edition). This monitor has a manufacturing carbon footprint of approximately 72.5 kg. Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors. -
Page 26: Troubleshooting
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. - Page 27 Display image is not sized properly • Use the OSD Image Adjust controls to increase or decrease the Coarse adjustment. • Check to make sure that a supported mode has been selected on the display card or system being used. (Please consult display card or system manual to change graphics mode.) •...
-
Page 28: Using The Multi Picture Function
Using the MULTI PICTURE function This monitor can display split screens from two sources by using any one of the input combinations shown on page 17. NOTE: Please see MULTI PICTURE (page 17) and PICTURE PATTERN (page 17). BRIGHTNESS and SOUND INPUT settings are set to be the same for both screens. SETUP 1. -
Page 29: Using The Zoom Function
Using the Zoom Function Allows you to use the entire screen area, signifi cantly expanding the size. Allows the picture displayed in the center to expand. NOTE: When LEFT or RIGHT is set at MULTI PICTURE, the other picture is expanded or reduced automatically. SETUP 1. - Page 30 B. The left image is set to be the main one. In this case, the priority image is set to be on the left side. The size of the image on the right side with black area is reduced. To enlarge the split images: use the following procedures to reduce the black area and enlarge the split images. 1.
-
Page 31: Human Sensing Function
Human sensing function Human sensing function reduces power consumption by detecting the movement of a person. The HUMAN SENSING has following two settings: MODE HUMAN SENSING SETTING No person in front of the monitor LIGHT BRIGHTNESS 0% DEEP Power saving mode Image of human sensing operation A. -
Page 32: Multi Display Setting
Multi Display setting You can display a image by using multiple monitors with any input signals. [Example of V MONITOR 5, H MONITOR 5 (See page 20)] 1. Touch the MENU/EXIT key to display OSD menu. 2. Move the LEFT/RIGHT key left or right to select MULTI DISPLAY. 3. - Page 33 Using ControlSync function with multi screen confi guration To control sub monitor from master monitor, control buttons of the master monitor is used. Please install master monitor at accessible place. Mounting multi screen confi guration When monitors are used in a multi screen confi guration for a longer time, slight expansion of the displays may happen due to temperature changes.
-
Page 34: Using The Auto Brightness Function
Using the Auto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient lighting within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions. -
Page 35: Manufacturer's Recycling And Energy Information
Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.