Cup Light; Background; Bluetooth; Emptying The Circuit - DèLonghi ECAM 650.85 Instruction Manual

3. Press " " to enable-
the beep;
4. Press " " to go back to the homepage.

8.14 Cup light

This function enables or disables the cup lights. The lighting is
enabled by default.
The lights come on each time a coffee or milk-based beverage is
made and during each rinsing cycle.
To disable or enable this function, proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press < (B10) or > (B8) until " cup lighting" appears on
the display (B);
3. Press " " to enable-
cup lighting;
4. Press " " to go back to the homepage.

8.15 Background

You can choose the display background from the following 4
alternatives: "SHADED BLUE", "STAINLESS STEEL", "COFFEE
BROWN", "DARK BLUE". Proceed as follows:
1. Press " " (B2) to enter the menu;
2. Press < (B10) or > (B8) until "
on the display (B);
3. Press " ". The available backgrounds appear on the
display;
4. Select the required background by pressing the chosen
panel. The appliance goes back to the settings menu with
the new background;
5. Press " " to go back to the homepage.

8.16 Bluetooth

This function enables or disables the protection PIN to connect to
the appliance from a device.
1. Press " " (B2) to enter the menu;
2. Press < (B10) or > (B8) until " BLUETOOTH" appears on
the display (B);
3. Enable or disable the PIN protection by pressing -
or
4. Press " " to go back to the homepage.
The preset PIN is "0000". You are recommended to customise the
PIN directly from the APP.
Please note!
The serial number of the appliance enables it to be identified
unambiguously when an association is created with the APP.
or disable-
or disable-
BACKGROUND" appears
;

8.17 Emptying the circuit

If the appliance is to be left idle for a period of time, or before
taking it to customer services, we recommend emptying the
water circuit.
Proceed as follows:
1. "EMPTY GROUNDS CONTAINER AND DRIP TRAY": extract and
empty the grounds container (A10) and drip tray (A14).
Press "
2. "INSERT GROUNDS CONTAINER AND DRIP TRAY": insert
the drip tray complete with grounds container;
3. "PLACE 0.5l CONTAINER UNDER SPOUTS, PRESS OK TO
START": position a container under the coffee spouts (A8)
and hot water spout (C6). Press "
Danger of burns!
the
Do not leave the appliance unattended while hot water is being
delivered.
7. "INSERT WATER TANK, PRESS OK TO CONTINUE": insert the
water tank and press "
8. "WATER CIRC. EMPTYING UNDERWAY": wait for the appli-
ance to empty the circuit; (Important: hot water from the
spouts!);
9. "EMPTY DRIP TRAY": remove, empty and reposition the drip
tray, then press "
10. "EMPTYING COMPLETE: PRESS OK TO TURN OFF": press "
". The appliance goes off.
Please note!
When turned on again, the appliance asks for the circuit to be
filled: follow the instructions from point 3 of section "5.1 Setting
up the appliance".

8.18 Default values

This resets all menu settings and programmed quantities back
to the default values (with the exception of the language which
remains as set).
13
";
" (fig. 8);
4. "RINSING
PLEASE WAIT": the ap-
pliance performs a rinse
cycle;
5. "EMPTY WATER TANK":
extract the tank (A16)
and empty it completely,
then press "
(fig. 10);
6. (If the filter is installed)
"REMOVE WATER SOFTEN-
10
ER FILTER": remove the
filter from the tank. Press
" ";
" (fig. 6);
";
UNDERWAY,
"