General Safety; Maintenance - BFT MOOVI 30 Installation And User Manual

INSTALLATION MANUAL
1) GENERAL SAFETY
WARNING! An incorrect installation or improper use ofthe product can
cause damage to persons, animals or things.
The "Warnings" leaflet and "Instruction booklet" supplied with t is
product should be read carefully as they provide important information
about safety, installation, use and maintenance.
Scrap packing materials (plastic, cardboard, polystyrene etc) accerdin
to the provisions set out by current standards. Keep nylon or polystyre e
bags out of children's reach.
Keep the instructions together with the technical brochure for f, ture
reference.
This product was exclusively design.ed and manufactured forlhe u~e
specified in the present documentation. Any other use not sReclfie In
this documentation could damage the product and be ang rous.
The Com pany decli nes all responsibi lityfor any conseq uences resu Iting from
improper use of the product, or use which is differe7t rom at exp cted
and specified in the present documentation.
Do not install the product in explosive atmospher·.
Make sure the stated temperature range is compatibl with the site in
which the automated system is due to be installed.
The units making upthe machine and its installa ion must meetthe requi e-
ments of the following European Directives: 004/1 08/EEC, 2006/9S/E~C,
98/37/EEC, 99/0S/EEC (and later amendme7 s). F, r all countries outside
the EEC,it is advisable to comply with tho/above-mentioned standards,
in addition to any national standards in force, 0 achieve a good level 0lf
safety.
The Company declines all responsibility for ny consequences resultin
from failure to observe Good Techni BI Pr tice when constructing clos
ing structures (door, gates etc.), as ell s from any deformation which
might occur during use.
The installation must comply wit the rovisions set out by the following
European Directives: 2004/1 08/,EEC,2006/9S/EEC, 98/37/EEC, 99/0S/EEG MAINTENANCE
and subsequent amendment. W RNING: before opening the oor, the spring must be unloaded
Disconnect the electrical po er supply before carrying out any wo k on (ve tical boom). WARNING: Before arry: g out any maintenance to the
the installation. Also discon ect any buffer batteries, if fitted. ins ,allation, disconnect the mains pow r supp.ly. The following points need
Have the automated system's ains power supply fitted with a swi ch c./iecking and maintenance:
oromnipolarthermal-magnefccircuit breaker with a contact separation Photocell optics. Clean occasionally.
of at least 3.5mm: the d vice must be connected uplinefrom the power Electricedge.Carryouta periodical man
supply terminals. stops the bar in case of obstacles.
Check that a differential s Itch with a 0.03A threshold isfittedjust before Dismantle the gearmotor and replace the lubri ating grease every two
the power supply ,ains ••. . .,.._----;,_--....,.-..-...,....-....,_,~--_Yeafs~.
....lI
Check that earthir g is carrie out correctly: connect al metal parts for When any operational malfunction is found, and ot resolved, discon-
closure (doors, g tes etc.) and aU
5
ste compone ts p 0 'ded 't a ecrthe aTns"powersupply-and-requesuhe-assistance of a specialised
earth terminal. technician (installer). When the operator is out of order, activate the
Keep mains connections well separated from low voltage connections. emergency release (see Fig. V), if necessary, so as to release the manual
Keep mains connections well separated (at least a 2.5mm air gap) from boom opening and closing operations.
safety extra low voltage connections.
During installation, wires must be secured with additional fastening
near the terminals or electrical connections, using devices such as cable
clamps.
Use wiring with double-insulated cables (sheathed cables) right up to the
immediate vicinity of terminals if safety extra low voltage cables need to
be run together with the low voltage supply cable. Similarly, the power
cable's sheathing must only be stripped back in the immediate vicinity
of the terminal board.
Specify that the actuator must be lifted by at least two operators or using
appropriate equipment.
Fitall the safety devices (photocells, electricedgesetc.) which are needed
to protectthe area from any danger caused by squashing, conveying and
shearing, according to and in compliance with the applicable directives
and technical standards.
Position at least one luminous signal indication device (blinker) where it
can be easily seen, and fix a Warning sign to the structure.
Any fixed controls must be installed within sight of the door but away
from moving parts. Unless the control is key operated, it must be installed
at a height of at least 1.5 m and in a place where it cannot be reached by
the public
Make sure that nothing can be crushed between the guided part and
surrounding fixed parts during operation
Once installation is complete, make sure the motor has the right settings
and that the safety and release systems are working properly.
The Company declines all responsibility with respect to the automation safety
and correct operation when other manufacturer's components are used.
Only use original parts for any maintenance or repair operation.
WARNING! Important safety instructions. Carefully read and comply with
the Warnings booklet and Instruction bookletthat come with the product as
incorrect installation can cause injury to people and animals and damage to
property. They contain important information regarding safety, installation,
use and maintenance. Keep hold of instructions so that you can attach them
to the technical file and keep them handy for future reference.
Do not modify the automation components, unless explicitly authorised
by the Company.
Instruct the product user about the control systems provided and the
manual opening operation in case of emergency.
Do not allow persons or children to remain in the automation operation
area.
Keep radio control or other control devices out of children's reach, in
order to avoid unintentional automation activation.
The user must avoid anyattempttocarryoutworkorrepairon theautoma-
tion system, and always request the assistance of qualified personnel.
Anything which is not expressly provided for in the present instructions,
is not allowed.
In allation must be carried out using the safety devices and controls
pre cribed by the EN 12978 Standard.
m
Z
WA NING! For connection to the mains power supply, use a multicore "
cable witll'-a cross-section of at least 3xl.Smm 2 ofthe kind provided for
r-
by the egulations mentioned above (by way of example, if the cable is
Vi
t protecteq, it must be rated H07 RN-F or higher, while ifit is protected
:::z:::
it ust lJe rated at least HOS W-F with a cross-section of 3xl.Smm2).
Only use p~astic raceways for both safety extra low voltage (SELV) cables
and low voltage 230 V) cables.
US OF AUTO ATI N
As utomation c n be emotelycontrolled and therefore not within sight, it is
es entia I to frequ ntly heck that all safety devices are perfectly efficient.
ARNING! In caseofan malfunction in the safety devices, take imme-diate
actlon and require t e ass' stance of a specialised technician.
I, is recommended to eep children at a safe distance from the automation
field of action.
CONTROL
The automation system is u ed toobtain motorised access control. Thereare
different types of control (m nua remote, magnetic badge, mass detector
etc.) depending on the installation rtquir~ments ~nd characteristics. For the
various control systems, see th relevant instructions. Do not use the auto-
mated device or put it into oper tion ntil the boom has been balanced.
SCRAPPING
Materials must be disposed of in conformity with the current regulations.
In case of scrapping, the automation devices do not entail any particular
risks or danger. In case of recovered materials, these should be sorted out
by type (electrical components, copper, aluminium, plastic etc.).
DISMANTLING
WARNING: before opening the door, the spring must be unloaded (verti-
cal boom). When the automation system is disassembled to be reassembled
on another site, proceed as follows:
Disconnect the power supply and the entire electrical installation.
Remove the actuator from its fixing base.
Disassemble all the installation components.
In the case where some of the components cannot be removed or are
damaged, they must be replaced.
Correct controller operation isonly ensured when the data contained in
the present manual are observed. The Company isnot to be held respon-
sible for any damage resulting from failure to observe the installation
standards and the instructions contained in the present manual.
The descriptions and illustrations contained in the present manual are
not binding. The Company reserves the right to make any alterations
deemed appropriate for the technical, manufacturing and commercial
improvement of the product, while leaving the essential product fea-
tures unchanged, at any time and without undertaking to update the
present publication.
MOOV130-50 - ALPHA 80M -
1 5