Ruckus Wireless ZoneFlex 7372-E Quick Setup Manual page 2

S 3: L I AP
TEP OG NTO THE
As specified earlier, the AP should be directly connected to your
computer (through the Ethernet port) and powered on, ready for
setup.
1 On your computer, open a Web browser window.
2
In the browser, type this URL to connect to the AP:
https://192.168.0.1
3
Press <Enter> to initiate the connection. When a security
OK/Yes
alert dialog box appears, click
4 When the Ruckus Wireless Admin login page appears, enter
the following:
Username
• : super
Password
• : sp-admin
5 Login
Click .
Default AP Settings (For Your Reference)
Network Names Wireless1—Wireless8 (2.4GHz radio)
(SSIDs) Wireless9—Wireless16 (5GHz radio)
Security (Encryption Disabled for each wireless interface
method)
Default Management 192.168.0.1
IP Address
S 4: C W
TEP USTOMIZE THE IRELESS
1 Configuration
On the Web interface menu, click
less
(Configuration > Radio 2.4G or Configuration > Radio
5G). The Configure :: Wireless :: Common options appear.
2 Verify that the following options are active:
Channel
• : SmartSelect
Country Code
• : If you are not located in the United
States, select your current country.
External Antenna
• : Enable the check box and enter
the external antenna gain in the field provided.
3 Click Update Settings if you made any changes.
4 Click any of the eight "Wireless #" tabs at the top of the
page.
Enabled
5 In Wireless Availability, click
6 SSID
Delete the text in the field, and then type a name for
your network that will help your users identify the AP in their
wireless network connection application.
Update Settings
7 Click to save your changes.
8
Repeat Steps 4-7 for each Wireless # interface that you want
to enable.
9 Logout
Click to exit the Web interface.
Copyright © 2013 Ruckus Wireless, Inc.
Published June 2013, Part Number 800-70494-001 Rev B
10 Disconnect the AP from the computer and from the current
power source, and then restore your computer to its original
network connection configuration.
S 5: P
TEP
1
Move the AP to its permanent location (accessible to both
AC power and network connection).
2
Use an Ethernet cable to connect the 10/100/1000 port of
the AP to your network.
to proceed.
NOTE:
If you will be using PoE, you will need a Cat5e (or better)
Ethernet cable to connect the AP to the PoE injector or switch.
3 Connect the AC power adapter (or PoE power supply) to the
AP, then to a convenient power source.
4
Verify that the 10/100/1000 port LED is lit.
5
Connect external antennas to the RP-SMA connectors on
the 7372-E enclosure. Note that each connector is a dual-
band (2.4 GHz & 5 GHz) spatial stream.
• Ruckus Wireless offers two different antenna kits as sep-
arately orderable accessories, certified for use with the
7372-E:
•
•
After a short pause to re-establish the Internet connection, you
can test the AP.
S
ETTINGS
S 6: V
TEP
Wire-
>
1
Using any wireless-enabled computer or mobile device,
search for and select the wireless network you previously
configured.
2
If you can connect, open a browser and link to any public
Web site.
Congratulations! Your wireless network is active and ready for
use.
.
AP Y S
LACE THE IN OUR ITE
911-0303-VP02 (articulating direct-mount antenna
pair)
911-0505-DP01 (2-stream sector antenna panel)
I
ERIFY THE NSTALLATION
Page 2 of 4