Related Manuals for Candy PL 604
Summary of Contents for Candy PL 604
- Page 1 INSTRUCTION FOR THE INSTALLATION AND OPERATION OF THE ELECTRIC HOB PL 604...
- Page 2 CONTENTS Unpacking the appliance ................3 Recommendations ..................3 • INSTALLATION Safety instructions ..................4 Electrical connection ................5 / 6 Fitting the hob ..................7 / 8 • USING THE APPLIANCE Presentation of the hob ................9 Technical data ..................9 The hot plate ..................
-
Page 3: Unpacking The Appliance
UNPACKING THE APPLIANCE Inside the appliance you will find a plastic bag containing the fixing brackets to install the hob in the worktop. RECOMMENDATIONS PLEASE READ THE FOLLOWING CAREFULLY IN ORDER TO GET THE BEST FROM YOUR APPLIANCE. Please keep the operating and installation instructions in a safe place for future reference. Before fixing the hob, note the serial number of the appliance just in case you may require repairs from after sales service organisation. -
Page 4: Electrical Connection
• Any queries regarding the power supply cord should be referred to After Sales Service or a qualified technician. The hob "PL 604" is supplied with a terminal block which enables you to choose the correct connection for the particular power supply. - Page 5 To proceed to the new connection, you mus adhere the following instructions • Before making the connection, make sure that the installation is protected by a suitable fuse, see table on next page, and that it is fitted with wires of a large enough section to supply the appliance normally.
- Page 6 INSTALLATION: "ELECTRICAL CONNECTION" 1rst Phase 1rst Phase 1rst Phase 1rst Phase Shunt 1 - 2 2nd Phase Shunt 1 - 2 Shunt 1 - 2 2nd Phase 3rd Phase Shunt 2 - 3 Shunt 2 - 3 Shunt 3 - 4 Neutral Neutral 2nd Phase...
- Page 7 INSTALLATION: "BUILDING-IN" Both the unit into which the hob will be fitted and any adjacent kitchen furniture must be made from heat resistant material and fixed with heat resistant adhesive. If, when installing the hob, the lower part of the casing is adjacent to an area normally accessible when handling or cleaning, fit a heatproof partition 1 cm below the base of the casing, with a 10 x 10 cm opening in the rear right-hand corner, to avoid any risk of burning or damage.
- Page 8 INSTALLATION: "BUILDING-IN" The body of the hob is fitted with 4 location holes to take the fixing brackets that secure the intended to fix the hob in the unit. Place the 4 fixing brackets in such a way that the hob surface is placed perfectly in the support unit.
-
Page 9: Technical Data
Building-in dimensions (cm) - (see chapter "Installation") Width : 56 Depth : Total electrical power : 7 kW In order to improve the quality of the products, CANDY may carry out modifications linked to technical improvements. Appliance meeting with the standard CEE 89/336, and 73/23. -
Page 10: The Hot Plate
THE HOT PLATE THE RAPID SELF-PROTECTING ELECTRIC HOT PLATE This is a cast-iron hot plate, controlled by a 7 position switch. As with the previous hot plate, each position corresponds to a permanent and progressive temperature according to the marks 1, 2, 3, 4, 5 and 6. An internal thermostat cuts off of the power supply if there is any overheating. - Page 11 For information, we note below the different powers reached according to the type of the plate and the control knob setting. Cooking with the electric hot plate To gest the best results from your appliance it is important to observe the following : •...
-
Page 12: General Maintenance 1
MAINTENANCE Before all cleaning or dismantling operation, it is imperative to : . disconnect the hob to the mains supply. . let all parts of the hob cool down. Never use : . harsh abrasives, scouring pads or sharp object to clean the hob. •... - Page 13 SA DES USINES DE ROSIERES - 30, rue Y. Lacelle - Rosières - 18400 LUNERY RCS Bourges B 553 720 053 - Capital de 18 000 000 F Tél. 02.48.55.78.00 - Télex 780868F - Fax 02.48.68.01.75...