Download Print this page
Texas Instruments MSP430G2955 Manual
Texas Instruments MSP430G2955 Manual

Texas Instruments MSP430G2955 Manual

Mixed signal microcontroller

Advertisement

Quick Links

www.ti.com
FEATURES
1
Low Supply-Voltage Range: 1.8 V to 3.6 V
Ultra-Low Power Consumption
– Active Mode: 250 µA at 1 MHz, 2.2 V
– Standby Mode: 0.7 µA
– Off Mode (RAM Retention): 0.1 µA
Five Power-Saving Modes
Ultra-Fast Wake-Up From Standby Mode in
Less Than 1 µs
16-Bit RISC Architecture, 62.5-ns Instruction
Cycle Time
Basic Clock Module Configurations
– Internal Frequencies up to 16 MHz With
Four Calibrated Frequency
– Internal Very-Low-Power Low-Frequency
(LF) Oscillator
– 32-kHz Crystal
– High-Frequency (HF) Crystal up to 16 MHz
– External Digital Clock Source
– External Resistor
Two 16-Bit Timer_A With Three
Capture/Compare Registers
One 16-Bit Timer_B With Three
Capture/Compare Registers
Up to 32 Touch-Sense-Enabled I/O Pins
DESCRIPTION
The Texas Instruments MSP430 family of ultra-low-power microcontrollers consists of several devices featuring
different sets of peripherals targeted for various applications. The architecture, combined with five low-power
modes, is optimized to achieve extended battery life in portable measurement applications. The device features a
powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency.
The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 1 µs.
The MSP430G2x55 series are ultra-low-power mixed signal microcontrollers with built-in 16-bit timers, up to 32
I/O touch-sense-enabled pins, a versatile analog comparator, and built-in communication capability using the
universal serial communication interface. For configuration details, see
Typical applications include low-cost sensor systems that capture analog signals, convert them to digital values,
and then process the data for display or for transmission to a host system.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
MIXED SIGNAL MICROCONTROLLER
Check for Samples: MSP430G2955, MSP430G2855,
MSP430G2755
Universal Serial Communication Interface
(USCI)
– Enhanced UART Supporting Auto Baudrate
Detection (LIN)
– IrDA Encoder and Decoder
– Synchronous SPI
2
– I
C™
On-Chip Comparator for Analog Signal
Compare Function or Slope Analog-to-Digital
(A/D) Conversion
10-Bit 200-ksps Analog-to-Digital (A/D)
Converter With Internal Reference, Sample-
and-Hold, and Autoscan
Brownout Detector
Serial Onboard Programming,
No External Programming Voltage Needed,
Programmable Code Protection by Security
Fuse
Bootstrap Loader
On-Chip Emulation Logic
Family Members are Summarized in
Package Options
– TSSOP: 38 Pin (DA)
– QFN: 40 Pin (RHA)
For Complete Module Descriptions, See the
MSP430x2xx Family User's Guide (SLAU144)
Table
1.
Copyright © 2013, Texas Instruments Incorporated
MSP430G2955
MSP430G2855
MSP430G2755
SLAS800 – MARCH 2013
Table 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the MSP430G2955 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Texas Instruments MSP430G2955

  • Page 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date.
  • Page 2 AVSS P4.7/TB0CLK/CA7 AVCC P4.6/TB0OUTH/A15/CA6 P4.0/TB 0 0. /CA0 P4.5/TB 2/A14 /CA5 P4.1/TB 1 0. /CA1 P4.4/TB 1/A13 /CA4 P4.2/TB 2 0. /CA2 P4.3/TB 0/A12 /CA3 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 3 JTAG Brownout WDT+ 3 CC IrDA,SPI Interface Protection 3 CC 3 CC Registers, USCI_B0: 15 or 16 Bit Registers Registers Shadow SPI,I2C Register Spy-Bi-Wire RST/NMI Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 4 Timer_A, compare: OUT2 output ADC10, analog input A4 VREF+/ Positive reference voltage output VEREF+ Positive reference voltage input (1) TDO or TDI is selected via JTAG instruction. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 5 (2) If XOUT/P2.7 is used as an input, excess current flows until P2SEL.7 is cleared. This is due to the oscillator output driver connection to this pad after reset. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 6 38, 39 Digital supply voltage Analog supply voltage 1, 4 Digital ground reference Analog ground reference QFN Pad QFN package pad; connection to DV recommended. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 7 MOV @Rn+,Rm MOV @R10+,R11 R10 + 2-- --> R10 Immediate ✓ MOV #X,TONI MOV #45,TONI #45 -- --> M(TONI) (1) S = source, D = destination Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 8 Low-power mode 4 (LPM4) – CPU is disabled. – ACLK, MCLK, and SMCLK are disabled. – DCO's dc generator is disabled. – Crystal oscillator is stopped. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 9 (8) The interrupt vectors at addresses 0FFDEh to 0FFC0h are not used in this device and can be used for regular program code if necessary. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 10 UCA0RXIFG rw-1 rw-0 rw-1 rw-0 UCA0RXIFG USCI_A0 receive interrupt flag UCA0TXIFG USCI_A0 transmit interrupt flag UCB0RXIFG USCI_B0 receive interrupt flag UCB0TXIFG USCI_B0 transmit interrupt flag Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 11 Segment A contains calibration data. After reset segment A is protected against programming and erasing. It can be unlocked but care should be taken not to erase this segment if the device-specific calibration data is required. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 12 The frequency is an average equal to: DCO(RSEL,DCO) 32 × f × f DCO(RSEL,DCO+1) DCO(RSEL,DCO) average MOD × f + (32 – MOD) × f DCO(RSEL,DCO) DCO(RSEL,DCO+1) Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 13 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 14 P3.6 - 25 CAOUT CCI1B CCR1 P3.7 - 28 P3.7 - 26 TA1.2 CCI2A P3.7 - 28 P3.7 - 26 PinOsc PinOsc TA1.2 CCI2B CCR2 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 15 (DTC) for automatic conversion result handling, allowing ADC samples to be converted and stored without any CPU intervention. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 16 TA1IV 011Ch Flash Memory Flash control 3 FCTL3 012Ch Flash control 2 FCTL2 012Ah Flash control 1 FCTL1 0128h Watchdog Timer+ Watchdog/timer control WDTCTL 0120h Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 17 Port P3 resistor enable P3REN 010h Port P3 selection P3SEL 01Bh Port P3 direction P3DIR 01Ah Port P3 output P3OUT 019h Port P3 input P3IN 018h Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 18 020h Special Function SFR interrupt flag 2 IFG2 003h SFR interrupt flag 1 IFG1 002h SFR interrupt enable 2 001h SFR interrupt enable 1 000h Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 19 Minimum processor frequency is defined by system clock. Flash program or erase operations require a minimum V of 2.2 V. Figure 1. Safe Operating Area Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 20 − Supply Voltage − V − DCO Frequency − MHz Figure 2. Active Mode Current vs V = 25°C Figure 3. Active Mode Current vs DCO Frequency Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 21 20.0 40.0 60.0 80.0 100.0 120.0 − Temperature − C − Temperature − C − Temperature − °C Figure 4. LPM3 Current vs Temperature Figure 5. LPM4 Current vs Temperature Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 22 The output is connected to the center tap of the divider. (2) The output voltage reaches at least 10% and 90% V at the specified toggle frequency. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 23 = 85°C −20 −40 = 25°C = 25°C −25 −50 − High-Level Output Voltage − V − High-Level Output Voltage − V Figure 8. Figure 9. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 24 − External Capacitance − pF LOAD LOAD A. One output active at a time. A. One output active at a time. Figure 10. Figure 11. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 25 CC(min) CC(min) V CC V hys(B_IT−) V (B_IT−) CC(start) t d(BOR) Figure 12. POR and BOR vs Supply Voltage Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 26 − Pulse Width − µs − Pulse Width − µs Figure 14. V Level With a Triangle Voltage Drop to Generate a POR and BOR Signal CC(drop) Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 27 RSEL RSEL DCO(RSEL+1,DCO) DCO(RSEL,DCO) range RSEL and RSEL+1 Frequency step between 1.08 ratio DCO(RSEL,DCO+1) DCO(RSEL,DCO) tap DCO and DCO+1 Duty cycle Measured at SMCLK output Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 28 3.3 V to 3.6 V ±3 calibrated at 30°C and 3 V (1) This is the frequency change from the measured frequency at 30°C over temperature. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 29 RSELx = 0...11 1.00 RSELx = 12...15 0.10 0.10 1.00 10.00 DCO Frequency − MHz Figure 15. DCO Wake-Up Time From LPM3 vs DCO Frequency Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 30 = 1M 0.25 0.25 0.00 0.00 −50.0 −25.0 25.0 50.0 75.0 100.0 − Temperature − C − Supply Voltage − V Figure 18. Figure 19. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 31 UNIT VLO frequency -40°C to 85°C VLO frequency temperature drift -40°C to 85°C %/°C VLO frequency supply voltage drift 25°C 1.8 V to 3.6 V Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 32 (4) Frequencies below the MIN specification set the fault flag, frequencies above the MAX specification do not set the fault flag, and frequencies in between might set the flag. (5) Measured with logic-level input frequency, but also applies to operation with crystals. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 33 UNIT Timer_A or Timer_B input clock SMCLK, duty cycle = 50% ± 10% TA/B SYSTEM frequency Timer_A or Timer_B capture timing TA0, TA1, TB0 TA/B,cap Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 34 Figure 22. SPI Master Mode, CKPH = 0 UCxCLK CKPL = 0 UCLK CKPL = 1 LO/HI LO/HI HD,MI SU,MI SOMI HD,MO VALID,MO SIMO Figure 23. SPI Master Mode, CKPH = 1 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 35 CKPL = 0 UCLK CKPL = 1 LO/HI LO/HI HD,SI SU,SI SIMO HD,MO STE,ACC STE,DIS VALID,SO SOMI Figure 25. SPI Slave Mode, CKPH = 1 Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 36 (2) The input offset voltage can be cancelled by using the CAEX bit to invert the Comparator_A+ inputs on successive measurements. The two successive measurements are then summed together. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 37 = 1.8 V = 2.2 V = 3 V = 3.6 V V /V – Normalized Input Voltage – V/V Figure 29. Short Resistance vs V Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 38 . Consumption is independent of the ADC10ON control bit, unless a conversion is active. The REFON bit enables the built-in reference to settle before starting an A/D conversion. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 39 REFBURST = 1, ADC10SR = 0 (1) Calculated using the box method: (MAX(-40 to 85°C) – MIN(-40 to 85°C)) / MIN(-40 to 85°C) / (85°C – (–40°C)) Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 40 ±1 Gain error ±1.1 ±2 Total unadjusted error ±2 ±5 (1) The reference buffer's offset adds to the gain, and offset, and total unadjusted error. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 41 (2) These values are hardwired into the Flash Controller's state machine (t = 1/f Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 42 (1) Once the fuse is blown, no further access to the JTAG/Test, Spy-Bi-Wire, and emulation feature is possible, and JTAG is switched to bypass mode. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 43 PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From Module P1.0/TA0CLK/ADCCLK P1.1/TA0.0 P1.2/TA0.1 P1.3/TA0.2 TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y Interrupt PxSEL.y Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 44 Timer0_A3.CCI1A Timer0_A3.TA1 Pin Osc Capacitive sensing P1.3/ P1.x (I/O) I: 0; O: 1 TA0.2/ Timer0_A3.CCI2A Timer0_A3.TA2 Pin Osc Capacitive sensing (1) X = don't care Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 45 PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select From JTAG To JTAG * Note: MSP430G2x53 devices only. MSP430G2x13 devices have no ADC10. Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 46 Pin Osc Capacitive sensing P1.7/ P1.x (I/O) I: 0; O: 1 TA0.2/ Timer0_A3.TA2 TDO/ 7 TDO TDI/ Pin Osc Capacitive sensing (1) X = don't care Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 47 PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From Module P2.0/TA0CLK/ACLK/A0 Keeper P2.1/TA0INCLK/SMCLK/A1 P2.2/TA0.0/A2 TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 48 PxSEL2.y PxSEL.y PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From ADC10 P2.3/TA0.1/A3/VREF-/VEREF- Keeper TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 49 PxSEL2.y PxSEL.y PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From ADC10 P2.4/TA0.2/A4/VREF+/VEREF+ Keeper TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 50 PxSEL2.y PxSEL.y PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From ADC10 P2.5/TA1.0/ROSC Keeper TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 51 I: 0; O: 1 TA1.0/ Timer1_A3.CCI0A Timer1_A3.TA0 ROSC (DCOR = 1 to enable its ROSC/ function) Pin Osc Capacitive sensing (1) X = don't care Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 52 1: Output PxSEL2.y PxSEL.y PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From Module XIN/P2.6 TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y Interrupt PxSEL.y Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 53 PIN NAME (P2.x) FUNCTION P2SEL.6 P2SEL2.6 P2DIR.x P2SEL.7 P2SEL2.7 XIN/ P2.6/ 6 P2.x (I/O) I: 0; O: 1 Pin Osc Capacitive sensing (1) X = don't care Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 54 1: Output PxSEL2.y PxSEL.y PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From Module XOUT/P2.7 TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y Interrupt PxSEL.y Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 55 FUNCTION P2SEL.6 P2SEL2.6 P2DIR.x P2SEL.7 P2SEL2.7 XOUT/ XOUT P2.7/ 7 P2.x (I/O) I: 0; O: 1 Pin Osc Capacitive sensing (1) X = don't care Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 56 PxSEL2.y PxSEL.y PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From Module P3.0/UCB0STE/UCA0CLK/A5 Keeper TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 57 PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From Module P3.1/UCB0SIMO/UCB0SDA P3.2/UCB0SOMI/UCB0SCL P3.3/UCB0CLK/UCA0STE TAx.y P3.4/UCA0TXD/UCA0SIMO TAxCLK P3.5/UCA0RXD/UCA0SOMI PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 58 PxSEL.y PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From Module P3.6/TA1.1/A6 Keeper P3.7/TA1.2/A7 TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 59 Capacitive sensing P3.7/ P3.x (I/O) I: 0; O: 1 TA1.2/ Timer1_A3.CCI2A 7 Timer1_A3.TA2 1 (y = 7) Pin Osc Capacitive sensing (1) X = don't care Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 60 PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From Module P4.0/TB0.0/CA0 Keeper P4.1/TB0.1/CA1 P4.2/TB0.2/CA2 TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 61 PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From Module P4.3/TB0.0/A12/CA3 Keeper P4.4/TB0.1/A13/CA4 P4.5/TB0.2/A14/CA5 TAx.y P4.6/TBOUTH/CAOUT/A15/CA6 TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 62 PxSEL2.y PxSEL.y PxREN.y PxSEL2.y PxSEL.y DVSS DVCC PxOUT.y From Module P4.7/TB0CLK/CAOUT/CA7 Keeper TAx.y TAxCLK PxIN.y To Module PxIE.y PxIRQ.y PxIFG.y PxSEL.y Interrupt Edge PxIES.y Select Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 63 P4.7/ P4.x (I/O) I: 0; O: 1 TB0CLK/ Timer0_B3.TBCLK CAOUT/ CAOUT CA7/ 1 (y = 7) Pin Osc Capacitive sensing (1) X = don't care Submit Documentation Feedback Copyright © 2013, Texas Instruments Incorporated Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755...
  • Page 64 PACKAGE OPTION ADDENDUM www.ti.com 6-Nov-2017 PACKAGING INFORMATION Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples Drawing (4/5) MSP430G2755IDA38 ACTIVE TSSOP Green (RoHS CU NIPDAU Level-2-260C-1 YEAR -40 to 85 G2755 &...
  • Page 65 PACKAGE OPTION ADDENDUM www.ti.com 6-Nov-2017 Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. MSL, Peak Temp.
  • Page 66 PACKAGE MATERIALS INFORMATION www.ti.com 13-Dec-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Reel Reel Pin1 Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant (mm) W1 (mm) MSP430G2755IDA38R TSSOP 2000 330.0 24.4 13.0 12.0 24.0 MSP430G2755IRHA40R VQFN...
  • Page 67 PACKAGE MATERIALS INFORMATION www.ti.com 13-Dec-2017 *All dimensions are nominal Device Package Type Package Drawing Pins Length (mm) Width (mm) Height (mm) MSP430G2755IDA38R TSSOP 2000 367.0 367.0 45.0 MSP430G2755IRHA40R VQFN 2500 367.0 367.0 38.0 MSP430G2755IRHA40T VQFN 210.0 185.0 35.0 MSP430G2855IDA38R TSSOP 2000 367.0 367.0...
  • Page 73 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.

This manual is also suitable for:

Msp430g2855Msp430g2755