Page 1 Cellular Shades Installation Instructions • Accu-Rise™ • Angles and Specialty Shapes • Arches, Circles and Quarter Circles • Assure™ • Auto-Lift® • Continuum™ • Cord Lock • Glissade™ • Sidelights • SkyFrame™ • SkyLite™ Manual • SkyLite w/ Auto-Lift • SlideArch™...
Page 2 Installation Instructions Parasol Cellular Shades Accu-Rise ™ Operating System Parasol Installation Instructions 2 BACK...
Page 3 Product View Installation Brackets Headrail Standard Bottom-Up Shade Day/Night Shade Handle Middle Rail Not Shown: Bottom-Up/Top-Down Shade Bottom Rail Parasol Installation Instructions 3 BACK...
Page 4 Longer #6 Hex Head Screw #6 Flat Head Screw and Screw #6 x 1 " Hex Head Screw for Use with Spacer Blocks for Use with Common (Provided with Each (Provided) (Not Provided) Headrail End Mounts Extension Bracket) (Provided) Parasol Installation Instructions 4 BACK...
Page 5 To prepare for this important first step, review the mounting types and basic window terminology illustrated below. Molding Head Jamb Jamb Jamb Collectively, the sill and jambs are called the Inside Mount Outside Mount “window casement.” Shade mounts outside Shade ﬁts within window opening. window opening. Sill Parasol Installation Instructions 5 BACK...
Page 6 ■ CAUTION: Use drywall anchors when mounting into drywall. Use a level to check that the mounting surface is level. Shim the brackets if necessary. ■ Attach the installation brackets using the screws provided. ■ Parasol Installation Instructions 6 BACK...
Page 7 CAUTION: The rear of the brackets must be flush against a flat mounting surface. Do not mount brackets on curved molding. Drill the screw holes using a " drill bit. ■ CAUTION: Use drywall anchors when mounting into drywall. Parasol Installation Instructions 7 BACK...
Page 8 IMPORTANT: Use drywall anchors when mounting into drywall. If using extension brackets, attach an installation ■ bracket to the underside of each extension bracket using the provided screws and speed nuts. Parasol Installation Instructions 8 BACK...
Page 9 Attach the end mount installation brackets using the flat head ■ screws provided. CAUTION: Drywall mounting is not recommended. IMPORTANT: For instructions on installing an arch over a rectangular shade, see the installation, instructions that came with your arch shade. Parasol Installation Instructions 9 BACK...
Page 10 On the mounting surface, mark the screw holes. ■ Drill the screw holes using a " drill bit. ■ Check that the brackets are level and aligned. ➤ Attach the hold-down brackets to the mounting surface using the screws provided. ■ Parasol Installation Instructions 10 BACK...
Page 11 Do not pull down on the bottom rail while turning the key. Lower Adjust the end pockets first. Then adjust any additional ■ Allen Wrench pockets as necessary to maintain equal tension across the bottom rail. Parasol Installation Instructions 11 BACK...
Page 12 With the middle rail fully raised, slowly and steadily push ■ up or pull down on the bottom rail handle. NOTE: The middle rail must be in the fully raised position to operate the bottom rail. Parasol Installation Instructions 12 BACK...
Page 13 Be sure the heads of the screws are flush against the installation bracket. Check that the headrail is completely inserted into the installation brackets. See “Install the Shade” on page 102. Parasol Installation Instructions 13 BACK...
Page 14 CAUTION: Do not vacuum XXX fabrics. For deeper cleaning, vacuum gently with a brush attachment. ■ Other cleaning methods described in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning 18-67IN-18 Parasol Installation Instructions 14 BACK 3/14...
Page 15 Installation Instructions Parasol Cellular Shades Angles and Specialty Shapes Parasol Installation Instructions 15 BACK...
Page 16 Installation Brackets Continuous Cord Loop Angle Sharing the Headrail with Continuous Cord Loop, Cordess, and Battery- Powered Shades Headrail Stand-Alone Angle Not Shown: Angle Bottom Angle Top Hexagon Octagon Trapezoid Bottom Rail Trapezoid Top-Down shades Parasol Installation Instructions 16 BACK...
Page 17 Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall. Speed Nut and Screw #6 x 1 " Longer #6 Hex Head Screw Hex Head Screw for Use with Spacer Blocks (Provided with Each (Provided) (Not Provided) Extension Bracket) Parasol Installation Instructions 17 BACK...
Page 18 Molding Head Jamb Jamb Jamb Collectively, the sill and jambs are called the Inside Mount Outside Mount “window casement.” Shade ﬁts within Shade mounts outside window opening. window opening. Sill Parasol Installation Instructions 18 BACK...
Page 19 Angle Top Shade Jamb Specialty Shape Shade (Bottom-Up Operation) Jamb 3" Space Evenly Space Evenly 3" Jamb Jamb Installation Brackets Specialty Shape Shade (Top-Down Operation) Installation Brackets 3" 3" Jamb Jamb location. Mount into wood whenever possible. Parasol Installation Instructions 19 BACK...
Page 20 See Chart For Depth mounting surface For Depth is level and the installation brackets are aligned. If mounting to a heavily textured surface, shim the brackets, if needed. IMPORTANT: Use drywall anchors when mounting into drywall. Parasol Installation Instructions 20 BACK...
Page 21 The solid side of the spacer blocks face the mounting surface. Spacer Blocks ■ Each spacer block projects the installation bracket " from mounting surface. Use a maximum of three spacer blocks per installation bracket. Parasol Installation Instructions 21 BACK...
Page 22 Lower the shade and place the pins from the hold-down brackets into the bottom Push rail end caps. ■ On the mounting surface, mark the screw holes. ■ Check that the brackets are level and aligned, and attach them using two screws. Parasol Installation Instructions 22 BACK...
Page 23 To install the mounting brackets for an inside mount see “Mount the Installation Brackets — Non-Operable Shade Inside Mount” ■ Install the top rail of the non-operable angle, see “Install the Stand-Alone Angle” ■ Fan out the angle towards the headrail of the rectangular shade. Parasol Installation Instructions 23 BACK...
Page 24 A magnet is attached to the ﬁller strip, ending 3" short of the right edge, ■ Place the fabric stack on top to accommodate the installation brackets. of the rail onto the magnet. Adjust the placement of the fabric as necessary. Parasol Installation Instructions 24 BACK...
Page 25 Bracket Type Minimum Fully Recessed " Standard 1" " " Standard* " " " " 3" Standard* " Swivel " " " Swivel* " 2" *Double cell fabrics use ” brackets. Parasol Installation Instructions 25 BACK...
Page 26 ■ If additional installation brackets came with your 3" order, space the additional bracket for each rail evenly between the two end brackets and mark their 3" location. Mount into wood whenever possible. Parasol Installation Instructions 26 BACK...
Page 27 Drill the screw holes using a " drill bit. IMPORTANT: Use drywall anchors when mounting into drywall. ■ Attach the installation brackets using the screws provided. ■ See mounting instructions for using spacer blocks or extension brackets. Parasol Installation Instructions 27 BACK...
Page 28 Locking Tab Screw Holes the brackets. ■ Rotate the moveable tabs against the rails to lock into place. Make sure the shade is tightly secured. Parasol Installation Instructions 28 BACK...
Page 29 One quarter turn of the key equals approximately ". Raise IMPORTANT: The Allen wrench key must be fully inserted Lower to avoid stripping the mechanism. Do not pull down on the Allen bottom rail while turning the key. Wrench Parasol Installation Instructions 29 BACK...
Page 30 The shade will not stay in the raised position. Solution To lock the shade in the raised position (or anywhere along the path to the fully raised position), engage the cordlock by pulling the cord toward the outside of the shade. Parasol Installation Instructions 30 BACK...
Page 31 Slide the tassel up the cord Tassel revealing the knot. ■ Make a new knot below the tassel at the desired location. ■ Trim the excess cord below the knot. ■ Slide the tassel back down over the knot. Parasol Installation Instructions 31 BACK...
Page 32 Back of Headrail Shade ■ After releasing the bottom edge, roll the back of the headrail down and out from the bracket. Bottom Parasol Installation Instructions 32 BACK...
Page 33 ■ Regular light dusting with a feather duster is all the cleaning that is needed in most circumstances. Vacuuming CAUTION: Do not vacuum XXX fabrics. ■ For deeper cleaning, vacuum gently with a brush attachment. Parasol Installation Instructions 33 BACK...
Page 34 Be sure the cleats are firmly secured. Once the cleats are attached, wrap excess cord around them after each use of the shade. 18-67IN-11 Parasol Installation Instructions 34 3/14 BACK...
Page 35 Installation Instructions Parasol Cellular Shades Arches, Circles, and Quarter Circles Parasol Installation Instructions 35 BACK...
Page 36 End Cap Magnet Fabric Headrail for Continuous Cord Loop, Cordless, or Battery-Powered Shades Disc Cover Quarter Circle Filler Strip Fabric End Cap Filler Strip Rail End Cap Quarter Circle Arch Cover Rail Specialty End Mount Bracket Parasol Installation Instructions 36 BACK...
Page 37 ■ Drywall Anchor (Not Provided). Use drywall anchors when mounting into drywall. Longer #6 Hex Head Screw #6 Flat Head Screw #6 x 1 " Hex Head Screw for Use with Spacer Blocks for Use with Common (Provi Headrail End Mounts (Provided) (Not Provided) Exten (Provided) Parasol Installation Instructions 37 BACK...
Page 38 Cord Pull Shade (Outside Mount Only) Spacer Blocks For Stand-Alone Arches, Arches, and Quarter Circles Sharing a Headrail with a Cord Pull Shade (Outside Mount Only) Extension Brackets For Stand-Alone Arches, Arches, and Quarter Circles (Outside Mount Only) Parasol Installation Instructions 38 BACK...
Page 39 Minimize Light Gap (Inside Mount Only) Arch Support Clip For Mounting Circles and to Help Support Fabric on Quarter Circles and Arches (Inside and Outside Mount) End Caps For Rail Ends IMPORTANT: For illustration purposes, the installation brackets for 3/4" are shown throughout the following instructions. The installation brackets for 3/8" and 11/4" pleat sizes follow the same installation procedures. Parasol Installation Instructions 39 BACK...
Page 40 If you have a tension support cord, pull the cord taut as you fan out and slide the fabric onto the rail. See photo. Top Cell Parasol Installation Instructions 40 BACK...
Page 41 Mark the rear hole only if the mounting depth is between " and 1". (There is only one mounting hole on " brackets.) CAUTION: Do not attach a screw through the swivel eyelet on the bracket. Parasol Installation Instructions 41 BACK...
Page 42 IMPORTANT: Be sure the bracket locations allow for the arch to completely cover the window opening. If more than two installation brackets came with your order, space additional bracket ➤ marks evenly between the two end marks. Mount into wood whenever possible. Parasol Installation Instructions 42 BACK...
Page 43 Long Insert the short end of the specialty end ■ mount brackets under each of the end caps and into the small fabric channels on the bottom of the rail. End Mount Bracket Rail Parasol Installation Instructions 43 BACK...
Page 44 Locking the back of the brackets. Locking Tab Screw Holes Rotate the moveable tabs against the rail ■ to lock into place. Make sure the shade is tightly secured. Parasol Installation Instructions 44 BACK...
Page 45 Center the arch on the rail. ■ Insert the end cap or cordlock back ■ into the rail. Top Cell Parasol Installation Instructions 45 BACK...
Page 46 For Outside Mounting Installations: Refer to the “Mount the Installation Brackets — Outside Mount” section in the Installation, Operation, and Care instructions that came with your rectangular shade. Use wall mount brackets in place of installation brackets. Parasol Installation Instructions 46 BACK...
Page 47 Also, the front edge of each bracket must be in the groove of the headrail. If any brackets are NOT installed correctly, release the shade and reinstall. If necessary, see “Removing Shade with a Headrail” Good Parasol Installation Instructions 47 BACK...
Page 48 Center the arch on ■ the rail. If necessary, adjust the filler strip in the top and bottom cells of the fabric stack. Proceed to “Attach Support Clips or Hooks” on page 20 Parasol Installation Instructions 48 BACK...
Page 49 3" location. Mount into wood whenever possible. IMPORTANT: The front edges of the installation brackets should be level and aligned. Installation Brackets 3" 3" 3" Parasol Installation Instructions 49 BACK...
Page 50 Center the brackets on your marks and ■ attach them using the screws provided. Check that the mounting surface is level and the brackets ➤ are aligned. If mounting to a heavily textured surface, shim the brackets, if needed. Parasol Installation Instructions 50 BACK...
Page 51 The solid side of the spacer blocks face the ➤ mounting surface. Each spacer block projects the installation bracket ➤ " from the mounting surface. Use a maximum of three spacer blocks per installation bracket. Parasol Installation Instructions 51 BACK...
Page 52 Rotate the moveable tabs against the rails to lock into place. Make sure the shade is ➤ tightly secured. If using arch support clips or hooks, proceed to “Attach Support Clips or Hooks” Parasol Installation Instructions 52 BACK...
Page 53 Position the outer edge of the clips where you want the outer edge of the circle. Install the clips with a screw through the slot at the back of the clip. ■ Do not tighten the screws yet. Parasol Installation Instructions 53 BACK...
Page 54 Repeat the process for the vertical cords with the top and bottom arch support clips. ■ Attach the disc cover, if desired. ■ Install the Circle Shade Into the Support Hooks or Clips If using additional support clips or hooks, proceed to “Attach Support Clips or Hooks” ■ Parasol Installation Instructions 54 BACK...
Page 55 45º from the bottom of the arch. Even Number of Hooks: Position the first two hooks ➤ No Hooks Below 45º at a 45º angle from the bottom center of the arch. Space the remaining hooks evenly. Parasol Installation Instructions 55 BACK...
Page 56 If arch support clips are used: ■ Arch Carefully tuck the shade into the clips. ➤ Support If necessary, bend or reconfigure to shape the arch to the ■ Clip best possible appearance. Front of Arch Parasol Installation Instructions 56 BACK...
Page 57 Removing the Shade with a Cord Pull Headrail Refer to the “Removing the Shade” section in the Installation, Operation, and Care ■ instructions that came with your rectangular shade. Parasol Installation Instructions 57 BACK...
Page 58 CAUTION: Do not vacuum XXX fabrics. For deeper cleaning, vacuum gently with a brush attachment. ■ Other cleaning methods described in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning 18-67IN-10 Parasol Installation Instructions 58 BACK 3/14...
Page 59 Installation Instructions Parasol Cellular Shades Assure ™ Operating System Parasol Installation Instructions 59 BACK...
Page 60 Product View Installation Brackets Headrail Bottom Rail Parasol Installation Instructions 60 BACK...
Page 61 Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall. ■ Speed Nut #6 x 1 " Longer #6 Hex Head Screw and Screw Hex Head Screw for Use with Spacer Blocks (Provided with Each Extension Bracket) (Provided) (Not Provided) Parasol Installation Instructions 61 BACK...
Page 62 To prepare for this important first step, review the mounting types and basic window terminology illustrated below. Molding Head Jamb Jamb Jamb Collectively, the sill and jambs are called the Inside Mount Outside Mount “window casement.” Shade ﬁts within Shade mounts outside window opening. window opening. Sill Parasol Installation Instructions 62 BACK...
Page 63 Attach the installation brackets using the screws provided. ■ Check that the mounting surface is level and the brackets are aligned. If mounting to a ➤ heavily textured surface, shim the brackets, if needed. Proceed to “Install the Shade” Parasol Installation Instructions 63 BACK...
Page 64 The top of the installation brackets or extension brackets should be at the desired shade ➤ height. IMPORTANT: The brackets must be level and aligned to each other. CAUTION: The rear of the brackets must be flush against a flat mounting surface. Do not mount brackets on curved molding. Installation Bracket Parasol Installation Instructions 64 BACK...
Page 65 The solid side of the spacer blocks faces the mounting surface. ➤ Extension If using extension brackets, attach an installation bracket to ■ Bracket the underside of each extension bracket using the provided Installation screws and speed nuts. Bracket Proceed to “Install the Shade” Parasol Installation Instructions 65 BACK...
Page 66 Remove the shade with the attached end mount brackets from the window. ■ Drill the screw holes using a " drill bit. ■ Attach the end mount brackets using the screws provided. ■ Proceed to “Operate the Shade” Parasol Installation Instructions 66 BACK...
Page 67 Bracket Rotate the swivel arm to snap the locking tab ■ in Open Position under the headrail. The shade is locked when the push tab is ■ against the headrail. Bracket in Locked Position Push Parasol Installation Instructions 67 BACK...
Page 68 1" 1" Pull the rail down Pull the rail down Lift the rail and Lift the rail and 1" beyond the sill. place on the sill. 1" beyond the sill. place on the sill. Parasol Installation Instructions 68 BACK...
Page 69 Problem When lowering the shade, it springs back above the desired length. Solution Be sure to lower and raise the shade several times to allow the fabric to relax. Parasol Installation Instructions 69 BACK...
Page 70 Pull the cord loop over the top of the entire ➤ Pull paper clip Tight Pull the cord tightly to form a slip knot. ➤ Slip Knot (Continued on following page) Parasol Installation Instructions 70 BACK...
Page 71 While holding the headrail, pull the push tab to rotate ■ the swivel arm to the open position to release the headrail. End Mount Brackets Reverse the installation procedures. See “Mount the Installation Brackets — End Mount” ■ Parasol Installation Instructions 71 BACK...
Page 72 CAUTION: Do not vacuum XXX fabrics. For deeper cleaning, vacuum gently with a brush attachment. ■ Other cleaning methods described in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning 18-67IN-34 Parasol Installation Instructions 72 BACK 3/14...
Page 73 Installation Instructions Parasol Cellular Shades Auto-Lift ™ Operating System Parasol Installation Instructions 73 BACK...
Page 74 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ■ Consult the dealer or an experienced radio/TV technician for help. ■ Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Parasol Installation Instructions 74 BACK...
Page 75 Battery Pack Mounting Bracket Options 18V Battery (Rear View) Wand with Battery Wand Clip Low Mount Battery Wand Bracket (Optional) High Mount Battery Wand Bracket (Standard) DC Power Supply Satellite Battery Pack or DC Power Supply (Optional) Parasol Installation Instructions 75 BACK...
Page 76 Longer #6 Hex Head Screw #6 Flat Head Screw and Screw Hex Head Screw for Use with Spacer Blocks for Use with Common (Provided with Each (Provided) (Not Provided) Headrail End Mounts Extension Bracket) (Provided) Parasol Installation Instructions 76 BACK...
Page 77 Should the spacer block become detached, reattach it. ■ Insert the legs of the installation bracket into the tabs ➤ on the spacer block. Rotate the installation bracket back, as shown. ➤ Parasol Installation Instructions 77 BACK...
Page 78 Jamb Minimum of 15" for Battery Wand 2" 2" Space Evenly Space Evenly Motor Shades with Optional Satellite Battery Pack or DC Power Supply (Top View) Jamb Jamb 2" Space Evenly 2" Space Evenly Motor Parasol Installation Instructions 78 BACK...
Page 79 Depth: End Mount Minimum Mounting " " " " " 3" Depth: Flush Mount (B) Minimum Flat Vertical " " " " " " Surface: Outside Mount See Depth Use Center Hole Chart When Depth Permits Parasol Installation Instructions 79 BACK...
Page 80 If more than two installation brackets came with your order, space them evenly between ➤ the two end brackets and mark their location. Mount into wood whenever possible. Headrail End Marks Minimum of 15" for Battery Wand 2" 2" Space Evenly Space Evenly Window Opening Parasol Installation Instructions 80 BACK...
Page 81 ■ CAUTION: Use drywall anchors when mounting into drywall. Attach the installation or extension brackets using the screws provided. ■ IMPORTANT: The front edges of the brackets must be level and aligned to each other. Parasol Installation Instructions 81 BACK...
Page 82 If using extension brackets, attach an installation bracket ■ to the underside of each extension bracket using the provided screws and speed nuts. Proceed to “STEP 2 — Install the Shade” Parasol Installation Instructions 82 BACK...
Page 83 CAUTION: Drywall mounting is not recommended. IMPORTANT: For instructions on installing an arch over a rectangular shade, see the installation, instructions that came with your arch shade. Proceed to “STEP 2 — Install the Shade” Parasol Installation Instructions 83 BACK...
Page 84 CAUTION: Be sure the power cable or satellite eye cable does not become pinched by the brackets or headrail during installation; damage or overheating of components could result. CAUTION: Do not connect the battery wand to the power cable prior to installing the shade. Parasol Installation Instructions 84 BACK...
Page 85 The satellite eye should face down, as shown in the illustration. After mounting the hinged flange, swivel the satellite eye ■ upward to the correct angle for receiving an infrared signal from the remote control. Parasol Installation Instructions 85 BACK...
Page 86 Check to make sure the battery wand is secure. CAUTION: Be sure the cable does not become pinched by the battery wand clip during installation. Damage or overheating of components could result. Parasol Installation Instructions 86 BACK...
Page 87 Slot Secure the power supply cable using wire retainers Battery Wand Cover ■ Socket (not supplied). If hiding the cable behind the shade, make sure it does not impede the operation of the shade. Parasol Installation Instructions 87 BACK...
Page 88 Plug an extension cable into the connector and the DC power supply. Two extension cables ■ and two connectors are used for three shades. Connector Power Cable Power Cable Extension Parasol Installation Instructions 88 BACK from Shade from Shade Cable...
Page 89 Connection Interface Installation Guide. Note: The wireless wall switch will not be available until 3Q 2014, but we left it in these instructions. If you wish, remove it from this page and the troubleshooting section. Parasol Installation Instructions 89 BACK...
Page 90 If more than two pockets exist, adjust the outer pockets first. Then adjust inner pockets ■ as necessary, to maintain equal tension across the bottom rail. As pocket adjustments are made, it is recommended that the shade be raised and lowered to check that it is level. Parasol Installation Instructions 90 BACK...
Page 91 Remote Control Guide or the Wireless Wall Switch Guide for further information or see “Resetting the Shade” on page 221. See the Remote Control Guide or the Wireless Wall Switch Guide for operation or programming troubleshooting solutions. Parasol Installation Instructions 91 BACK...
Page 92 Lower the shade completely to allow it to “self-correct” skewing. Check that the headrail and installation brackets are level and aligned. Shim the installation brackets to level the headrail, if necessary. Adjust the bottom rail. See “Level the Bottom Rail (If Necessary)” on page 18. Parasol Installation Instructions 92 BACK...
Page 93 CAUTION: Do not vacuum XXX fabrics. For deeper cleaning, vacuum gently with a brush attachment. ■ Other cleaning methods described in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning 18-67IN-23 Parasol Installation Instructions 93 BACK 3/14...
Page 94 Installation Instructions Parasol Cellular Shades Continuum ™ Operating System Parasol Installation Instructions 94 BACK...
Page 95 Product View Installation Brackets Standard Bottom-Up Shade Cord Tensioner and Bracket Hold-Down Brackets (Optional) Bottom Rail Headrail Bottom-Up/Top-Down Shade Middle Rail Not Shown: Day/Night Shade Two-On-One Headrail Shade Parasol Installation Instructions 95 BACK...
Page 96 Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall. ■ Speed Nut and Screw Longer #6 Hex Head Screw #6 x 1 " Hex Head Screw for Use with Spacer Blocks (Provided with Each Extension Bracket) (Provided) (Not Provided) Parasol Installation Instructions 96 BACK...
Page 97 To prepare for this important first step, review the mounting types and basic window terminology illustrated below. Molding Head Jamb Jamb Jamb Collectively, the sill and jambs are called the Inside Mount Outside Mount “window casement.” Shade mounts outside Shade ﬁts within window opening. window opening. Sill Parasol Installation Instructions 97 BACK...
Page 98 IMPORTANT: Use drywall anchors when mounting into drywall. Use a level to check that the mounting surface is level. Shim the brackets if necessary. ■ Attach the installation brackets using the screws provided. ■ Proceed to “Install the Shade” Parasol Installation Instructions 98 BACK...
Page 99 CAUTION: The rear of the brackets must be flush against a flat mounting surface. Do not mount brackets on curved molding. Drill the screw holes using a " drill bit. ■ IMPORTANT: Use drywall anchors when mounting into drywall. Parasol Installation Instructions 99 BACK...
Page 100 IMPORTANT: Use drywall anchors when mounting into drywall. If using extension brackets, attach an installation ■ bracket to the underside of each extension bracket using the provided screws and speed nuts. Proceed to “Install the Shade” Parasol Installation Instructions 100 BACK...
Page 101 Attach the end mount installation brackets using the flat head ■ screws provided. IMPORTANT: Drywall mounting is not recommended. IMPORTANT: For instructions on installing an arch over a rectangular shade, see the installation, instructions that came with your arch shade. Proceed to “Install the Shade” Parasol Installation Instructions 101 BACK...
Page 102 On the mounting surface, mark the screw holes. ■ " drill bit. Drill the screw holes using a ■ Check that the brackets are level and aligned. ➤ Attach the hold-down brackets to the mounting surface using the screws provided. ■ Parasol Installation Instructions 102 BACK...
Page 103 Do not pull down on the bottom rail while turning the key. Adjust the end pockets first. Then adjust any additonal pockets as necessary to maintain ■ equal tension across the bottom rail. Parasol Installation Instructions 103 BACK...
Page 104 (unless reverse controls were specified on the order). IMPORTANT: You must first lower the bottom rail before lowering the middle rail. Likewise, you must first raise the middle rail before raising the bottom rail. Parasol Installation Instructions 104 BACK...
Page 105 For Bottom-Up/Top-Down shades: Both the middle rail and the bottom rail may skew if the cord loop is pulled too quickly. Lower each rail completely to allow them to “self-correct”. Adjust the bottom rail. “Level the Bottom Rail (If Necessary)” Parasol Installation Instructions 105 BACK...
Page 106 Universal Cord Tensioner Installation Kit. Problem The universal cord tensioner grabs onto the cord upon operation. Solution Check that the universal cord tensioner is mounted properly. Reinstall, if necessary. See the instructions included with your Universal Cord Tensioner Installation Kit. Parasol Installation Instructions 106 BACK...
Page 107 CAUTION: Do not vacuum XXX fabrics. For deeper cleaning, vacuum gently with a brush attachment. ■ Other cleaning methods described in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning Parasol Installation Instructions 107 BACK...
Page 108 Fasteners provided in this kit may not be appropriate for all mounting surfaces. ■ Use appropriate anchors for the mounting surface conditions. Only the supplied cord tensioners and hardware should ■ be used. Replacement parts may be obtained by contacting your window coverings dealer. 18-67IN-05 Parasol Installation Instructions 108 BACK 3/14...
Page 109 Installation Instructions Parasol Cellular Shades Standard Cord-Lock Operating System Parasol Installation Instructions 109 BACK...
Page 110 Product View Cordlock Installation Brackets Equalizer Standard Bottom-Up Shade Tassel Cord Tassel Top-Down Shade Breakaway Cord Stop Not Shown: Bottom-Up/Top-Down Shade Day/Night Shade Two-On-One Headrail Shade Parasol Installation Instructions 110 BACK...
Page 111 Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall. ■ Speed Nut Longer #6 Hex Head Screw and Screw #6 x 1 " Hex Head Screw for Use with Spacer Blocks (Provided with Each (Provided) (Not Provided) Extension Bracket) Parasol Installation Instructions 111 BACK...
Page 112 To prepare for this important first step, review the mounting types and basic window terminology illustrated below. Molding Head Jamb Jamb Jamb Collectively, the sill and jambs are called the Inside Mount Outside Mount “window casement.” Shade ﬁts within Shade mounts outside window opening. window opening. Sill Parasol Installation Instructions 112 BACK...
Page 113 Attach the installation brackets using the screws provided. ■ Check that the mounting surface is level and the brackets are aligned. If mounting to a ➤ heavily textured surface, shim the brackets, if needed. Proceed to “Install the Shade” Parasol Installation Instructions 113 BACK...
Page 114 The top of the installation brackets or extension brackets should be at the desired shade ➤ height. IMPORTANT: The brackets must be level and aligned to each other. CAUTION: The rear of the brackets must be flush against a flat mounting surface. Do not mount brackets on curved molding. Parasol Installation Instructions 114 BACK...
Page 115 The solid side of the spacer blocks faces the mounting surface. ➤ Speed If using extension brackets, attach an installation bracket to ■ Extension the underside of each extension bracket using the Bracket provided screws and speed nuts. Installation Bracket Proceed to “Install the Shade” Parasol Installation Instructions 115 BACK...
Page 116 Remove the shade with the attached end mount brackets from the window. ■ Drill the screw holes using a " drill bit. ■ Attach the end mount brackets using the screws provided. ■ Proceed to “Operate the Shade” Parasol Installation Instructions 116 BACK...
Page 117 Lower the shade and place the pins from the hold-down ■ brackets into the bottom rail end caps. On the mounting surface, mark the screw holes. ■ Check that the brackets are level and aligned, and ■ attach them using two screws. Parasol Installation Instructions 117 BACK...
Page 118 IMPORTANT: You must first lower the bottom rail before lowering the center rail. Middle Rail Likewise, you must first raise the center Disengaged rail before raising the bottom rail. Cordlock Bottom Rail Parasol Installation Instructions 118 BACK...
Page 119 The shade will not stay in the raised position. Solution To lock the shade in the raised position (or anywhere along the path to the fully raised position), engage the cordlock by pulling the cord toward the outside of the shade. Parasol Installation Instructions 119 BACK...
Page 120 Loop the cord around the ferrule and back loop ﬁts into the ferrule through the tapered end. Make sure the loop fits into groove. the groove on the side of the ferrule. Cord Loop Parasol Installation Instructions 120 BACK...
Page 121 Slide the tassel up the cord revealing the knot. ■ Make a new knot below the tassel at the desired ■ Tassel location. Trim the excess cord below the knot. ■ Slide the tassel back down over the knot. ■ Parasol Installation Instructions 121 BACK...
Page 122 CAUTION: Do not vacuum XXX fabrics. For deeper cleaning, vacuum gently with a brush attachment. ■ Other cleaning methods described in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning Parasol Installation Instructions 122 BACK...
Page 123 IMPORTANT: Should the breakaway cord stop break apart, be sure to untangle the cords prior to reassembling. Fit the bottom Swing the top Breakaway edges together edges together. Cord Stop and snap closed. 18-67IN-12 Parasol Installation Instructions 123 BACK 3/14...
Page 124 Installation Instructions Parasol Cellular Shades Left Stack Right Stack Split Stack (Center Opening) and Day/Night Traveling Center Stack Glissade ™ Parasol Installation Instructions 124 BACK...
Page 125 Rail Carrier End Plate Screw Fabric Carrier Snap Pin Stationary Rail Bracket Stationary Handle Rail Left Stack Design Stationary Rail Bottom Bracket Not Shown: Inside Mount Right Stack Adaptor Split Stack Traveling Center Stack Day/Night Designs Parasol Installation Instructions 125 BACK...
Page 126 Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall. ■ Speed Nut #6 x 1 " Longer #6 Hex Head Screw and Screw Hex Head Screw For Use With Spacer Blocks (Provided With Each (Provided) (Not Provided) Extension Bracket) Parasol Installation Instructions 126 BACK...
Page 127 Left Stack Right Stack Split Stack (Center Opening) and Day/Night Traveling Center Stack Right Stack Traveling Traveling Right Stack Center Stack Center Stack Split Stack (Center Opening) Split Stack and Day/Night (Center Opening) and Day/Night Parasol Installation Instructions 127 BACK...
Page 128 Shims are Shade Brackets Width Required Installation Shim 12" – 31" Bracket " – 66" " – 96" " – 139" provided with brackets for inside mounted shades. " – 168" Parasol Installation Instructions 128 BACK...
Page 129 Center the brackets on your marks and mark the screw holes. ■ When using extension brackets, mark two screw holes per bracket. ➤ Drill the screw holes using a " drill bit. ■ IMPORTANT: Use drywall anchors when mounting into drywall. " Parasol Installation Instructions 129 BACK...
Page 130 Do not mount installation brackets on curved molding. Spacer Blocks If using extension brackets, attach an installation ■ bracket to the underside of each extension bracket using the provided screws and speed nuts. Proceed to “Prepare the Rails” Parasol Installation Instructions 130 BACK...
Page 131 Drill the screw holes using a " drill ■ bit. Attach the installation brackets using the ■ screws provided. IMPORTANT: Be sure the front edges of the installation brackets are level and aligned to each other. Proceed to “Prepare the Rails” Parasol Installation Instructions 131 BACK...
Page 132 NOTE: Do not insert the bracket completely. Leave at least " of the bracket showing below the stationary rail. Window Side (Left Stack Illustrated) Front of Shade " Stationary Rail Base Extends Stationary Rail Toward Bottom Bracket the Window Parasol Installation Instructions 132 BACK Base...
Page 133 Slide the moving rail bracket into the ➤ moving rail. Align the hole in the bracket with the ➤ hole in the moving rail. Push the snap pin through both ➤ the moving rail and the moving rail bracket. Parasol Installation Instructions 133 BACK...
Page 134 Position the center pull plate on the underside ■ of the headrail as shown. Align the plate to the center mark. ■ Attach the center pull plate with a screw into the ■ cord tensioner channel. Parasol Installation Instructions 134 BACK...
Page 135 Center Stack design: Slide the second moving rail bracket into the rear track. ➤ Insert the moving rail bracket(s) into the rear track. Front of Headrail Insert the fabric carrier bearings into the front track. Parasol Installation Instructions 135 BACK...
Page 136 Only attach the left end plate (the end plate without the cord tensioner attached). IMPORTANT: The stationary rail bracket must butt up against the end plate. If necessary, gently tap the bracket toward the end plate. Parasol Installation Instructions 136 BACK...
Page 137 Use the screw to attach the end plate ■ End Plate Cord with the holes toward the front of Tensioner the headrail. Traveling Center Stack Traveling Center Stack Only Attach the other end plate to the headrail. ■ Parasol Installation Instructions 137 BACK...
Page 138 Also, the front edge of each bracket must be in the groove of the headrail. If any brackets are not installed correctly, release the shade and reinstall. See “Removing the Shade (If Necessary)” Good Parasol Installation Instructions 138 BACK...
Page 139 Rail Stationary Rail bracket to mount the stationary Bottom Bracket rail away from the wall. An Extension extension bracket may be Bracket necessary if you used spacer blocks or extension brackets with the installation brackets. Parasol Installation Instructions 139 BACK (Side View)
Page 140 Align the Adapter screw hole of the adaptor to face the side jamb Stationary Rail (or side wall). Bottom Bracket Secure with a screw (provided) through the ■ inside mount adaptor and into the side jamb. Parasol Installation Instructions 140 BACK...
Page 141 If the moving rail does not move smoothly, slide the cord tensioner toward the end plate ➤ until you feel the tension lessen. Check if the moving rail holds the shade in place, at any position, by moving the rail back ➤ and forth several times. Parasol Installation Instructions 141 BACK...
Page 142 To Adjust the Bottom of the Moving Rail to the Left Loosen the right screw turn, then tighten ■ the left screw turn. Repeat until the shade is properly aligned. After adjustment, tighten both screws ■ completely. Parasol Installation Instructions 142 BACK...
Page 143 NOTE: It is normal for the prongs on the lock to separate when the screwdriver is inserted. Once the valance corner end cap is attached to the valance ■ return, repeat the steps to attach the valance corner end cap to the valance. Parasol Installation Instructions 143 BACK...
Page 144 The curve of the handle should face out, away from the fabric. Attach the handle to its moving rail using the ■ provided screws. Split Stack and Day/Night designs: Repeat ■ the above steps for the second moving rail. Parasol Installation Instructions 144 BACK...
Page 145 Solution Add a shim to each installation bracket to provide additional space to attach the headrail and/or valance. Shims are provided for inside and ceiling mounts. See “Inside/Ceiling Mount — Mount the Installation Brackets” Parasol Installation Instructions 145 BACK...
Page 146 Problem The fabric billows out when moving the shade to the stacked (fully open) position. Solution Increase the cord tension. Slide the cord tensioner toward the fabric stack slightly to increase the tension. See “Adjust the Cord Tension” Parasol Installation Instructions 146 BACK...
Page 147 Cellular shades are made of anti-static, dust-resistant fabric which repels dirt and dust. For most fabrics, the following cleaning options are available. Dusting Regular light dusting with a feather duster is all the cleaning that is needed in most ■ circumstances. Parasol Installation Instructions 147 BACK...
Page 148 CAUTION: Do not vacuum XXX fabrics. For deeper cleaning, vacuum gently with a brush attachment. ■ Other cleaning methods desrcibed in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning 18-67IN-07 Parasol Installation Instructions 148 BACK 3/14...
Page 149 Installation Instructions Parasol Cellular Shades Cordless Operable Sidelights Parasol Installation Instructions 149 BACK...
Page 150 Product View Installation Brackets Headrail Middle Rail Bottom Rail Not Shown: Standard Bottom Up Bottom-Up/Top-Down Non-Operable Installation Brackets Note: The installation procedures for non-operable sidelights Parasol Installation Instructions 150 BACK are the same as those for operable ones.
Page 151 Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall. Speed Nut Longer #6 Hex Head Screw #6 x 1 " and Screw Hex Head Screw for Use with Spacer Blocks (Provided with Each (Provided) (Not Provided) Extension Bracket) Parasol Installation Instructions 151 BACK...
Page 152 Head Jamb Jamb Sill Collectively, the sill and Inside Mount Outside Mount jambs are called the Shade ﬁts within Shade mounts outside “window casement.” window opening. window opening. Parasol Installation Instructions 152 BACK...
Page 153 Attach the installation brackets at the top and bottom of the window opening using the screws provided. ■ Check that the mounting surface is level and the brackets are aligned. If mounting to a heavily textured surface, shim the brackets, if needed. Proceed to “Install the Shade” Parasol Installation Instructions 153 BACK...
Page 154 CAUTION: The rear of the brackets must be flush against a flat mounting surface. Do not mount brackets on curved molding. Installation Bracket ■ Drill the screw holes using a " drill bit. IMPORTANT: Use drywall anchors when mounting into drywall. Parasol Installation Instructions 154 BACK...
Page 155 If using extension brackets, attach an installation bracket to the underside of each extension bracket using the Speed provided screws and speed nuts. Extension ■ Repeat these steps for the bottom rail. Bracket Installation Bracket Proceed to “Install the Shade” Parasol Installation Instructions 155 BACK...
Page 156 Gently push the fabric away from the end mount bracket to allow access to the screw holes. ■ Secure the brackets using two screws provided. ■ Install the bottom rail using its installation brackets. Proceed to “Operate the Shade” Parasol Installation Instructions 156 BACK...
Page 157 The bottom rail should be approximately 1" above the bottom mounted brackets. ■ Pull down on the bottom rail (to engage the spring in the headrail) and install it into the bottom brackets, as described above. Parasol Installation Instructions 157 BACK...
Page 158 To completely raise the shade (fabric stack at the top), first raise the top moving rail fully, then raise the bottom moving rail. ■ To completely lower the shade (fabric stack at the bottom), first lower the bottom moving rail fully, then lower the top moving rail. Parasol Installation Instructions 158 BACK...
Page 159 Check the installation brackets. Make sure the shade fabric is not caught between the bracket tab and the headrail. Problem The shade length is either too short or too long. Too short: the shade won’t snap into the bottom bracket. Too long: the fabric buckles. Parasol Installation Instructions 159 BACK...
Page 160 Once you are certain of the final ferrule down adjustments, tape the extra cord length to lengthen the cord. to the bottom rail or place into the groove on the bottom rail for future adjustments. Parasol Installation Instructions 160 BACK...
Page 161 Loop the cord around the ferrule and back through the tapered end. Make sure the loop fits into the groove on the side of Be sure the cord loop ﬁts into the ferrule. the ferrule groove. Cord Loop Parasol Installation Instructions 161 BACK...
Page 162 CAUTION: Do not vacuum XXX fabrics. ■ For deeper cleaning, vacuum gently with a brush attachment. Other cleaning methods described in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning 18-67IN-17 Parasol Installation Instructions 162 BACK 3/14...
Page 163 Installation Instructions Parasol Cellular Shades SkyFrame Application ™ Parasol Installation Instructions 163 BACK...
Page 164 Product View Headrail Side Track Fabric Handle Moving Rail Support Cord (For Sloped Tension Cord Shades More Than 36" Wide) Side Track Anchor Rail Parasol Installation Instructions 164 BACK...
Page 165 Drywall Anchors (Not Provided). Use drywall anchors when mounting into drywall. ■ Speed Nut #6 x 1 " Longer #6 Hex Head Screw and Screw Hex Head Screw for Use with Spacer Blocks (Provided with Each (Provided) (Not Provided) Extension Bracket) Parasol Installation Instructions 165 BACK...
Page 166 To prepare for this important first step, review the mounting types and basic window terminology illustrated below. Molding Head Jamb Jamb Jamb Collectively, the sill and jambs are called the Inside Mount Outside Mount “window casement.” Shade ﬁts within Shade mounts outside window opening. window opening. Sill Parasol Installation Instructions 166 BACK...
Page 167 Attach the installation brackets using the ■ screws provided. Check that the mounting surface is ➤ level and the brackets are aligned. If mounting to a heavily textured surface, shim the brackets, if needed. Proceed to “Install the Shade” Parasol Installation Instructions 167 BACK...
Page 168 IMPORTANT: The brackets must be level and aligned to each other. CAUTION: The rear of the brackets must be flush against a flat mounting surface. Do not mount brackets on curved molding. Installation Bracket Extension Bracket Parasol Installation Instructions 168 BACK...
Page 169 The solid side of the spacer blocks faces the mounting surface. ➤ Speed If using extension brackets, attach an installation bracket to ■ Extension the underside of each extension bracket using the provided Bracket screws and speed nuts. Installation Bracket Proceed to “Install the Shade” Parasol Installation Instructions 169 BACK...
Page 170 Make sure the side tracks are parallel by measuring the distance between them at the top ■ and bottom of the window. If the side tracks are more than " off of parallel, use shims under the mounting screw ■ locations, starting at the ends of the side tracks. Parasol Installation Instructions 170 BACK...
Page 171 Inside mounts: Attach the anchor rail directly to the ■ sill by using the additional 2 screws provided. NOTE: The screw holes are pre-drilled in the anchor rail. Center the rail within the side tracks before mounting. ■ Anchor Rail Inside Mount Parasol Installation Instructions 171 BACK...
Page 172 ■ Pull the cord through the two washers to the desired tension. ■ Tighten the screw. ■ Support Cord Make sure the cord is held taut between the washers. ■ Clamping Screw Support Cord Washers Parasol Installation Instructions 172 BACK...
Page 173 Extension Pole Place the hook on the extension pole ■ around the moving rail handle. Slowly and steadily push up or pull down ■ on the moving rail handle to raise or lower. Parasol Installation Instructions 173 BACK...
Page 174 This may cause the shade to be angled or tilted when fully raised. Try lowering the shade completely, then raising it to allow it to self-correct. Adjust the cord tension. See “Adjust the Shade” Parasol Installation Instructions 174 BACK...
Page 175 CAUTION: Do not vacuum XXX fabrics. For deeper cleaning, vacuum gently with a brush attachment. ■ Other cleaning methods described in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning 18-67IN-16 Parasol Installation Instructions 175 BACK 3/14...
Page 176: Manual Operation
Installation Instructions Parasol Cellular Shades SkyLite with ™ Manual Operation Parasol Installation Instructions 176 BACK...
Page 177 (Right) Rail End Cap Moving Rail Tension Cable Side Rail (Left) Bottom Tension Plate and Screw Bottom Corner Bracket Control Knob Spacer Blocks Bottom Rail Outside Mount Installation Bracket Crank Handle (Optional) Extension Pole (Optional) Parasol Installation Instructions 177 BACK...
Page 178 Level (laser level is recommended) ■ Measuring tape and pencil ■ Needle-nose pliers ■ Phillips screwdriver (magnetized screwdriver is recommended) ■ Power drill, " drill bit, and " hex driver ■ Sharp scissors ■ Tape Parasol Installation Instructions 178 BACK...
Page 179 ■ Slide the moving rail end caps close to the top corner brackets. “L” “R” Top Corner Bracket Moving Rail End Cap Moving Rail End Cap - Left - Right White Grey Bottom Corner Bracket Parasol Installation Instructions 179 BACK...
Page 180 ", ". If necessary, break off the outer tabs to adjust the spacer block to the appropriate size, so the shade fits evenly into the casement. NOTE: The spacer blocks are packaged with the corner covers. Parasol Installation Instructions 180 BACK...
Page 181 ■ Repeat the above steps on the right side. If there are more than two tension cables: ■ Make sure all the top tension screw(s) and the top tension plate(s) are in place. Parasol Installation Instructions 181 BACK...
Page 182 Align the left end of the shaft in the bottom rail with Leveling Sockets the drive gear shaft. ■ Slide the leveling socket onto the shaft and tighten the locking Locking Collar collar using the provided " Allen wrench. Parasol Installation Instructions 182 BACK...
Page 183 Align the right end of shaft in the bottom rail with the drive gear shaft. Locking Collar ■ Slide the leveling socket onto the shaft and tighten the locking collar using the provided " Allen wrench. Parasol Installation Instructions 183 BACK...
Page 184 Pull the bead chain taut and secure the other end of bead chain in the slot in the bottom right corner bracket. IMPORTANT: Make sure the bead chain is under the tension cable brackets and taut in order to hold the side rails together. Parasol Installation Instructions 184 BACK...
Page 185 Make sure all the tension cables are in the center of the holes in the rail cover. ■ Move the tension bracket(s) if necessary. IMPORTANT: Be sure the cover is centered on the bottom rail. Parasol Installation Instructions 185 BACK...
Page 186 Attach the Crank Handle (Optional) ■ Unscrew and remove the control knob. ■ Attach the handle using the screw provided. ■ Align the handle so the set screw is tightened against the flat part of the protruding shaft. Parasol Installation Instructions 186 BACK...
Page 187 After the moving rail is level, slide the leveling socket onto the drive gear shaft and tighten the locking collar. ■ Operate the shade to verify that the shade is level. Repeat the above steps, if necessary. ■ Reinstall the bottom rail cover. Parasol Installation Instructions 187 BACK...
Page 188 Roll the bracket so that the holes touch the Roll ■ side jamb. Sill ■ Mark and drill the screw holes using a " 1" Installation drill bit. Brackets Jamb ■ Attach the installation brackets using the screws provided. Sill Parasol Installation Instructions 188 BACK...
Page 189 Corner Cover ■ Remove the adhesive backing from the corner covers. ■ Press a cover onto each shade corner, extending them to the window frame to cover the light gap. Proceed to “Operate the Shade” Parasol Installation Instructions 189 BACK...
Page 190 IMPORTANT: You may need another person to assist you with this installation. Attach the Installation Brackets to the Shade ■ Attach the installation brackets to the shade through pre-drilled holes on the side rails using the " screws provided. Parasol Installation Instructions 190 BACK...
Page 191 Mark the screw holes and drill them using a " drill bit. IMPORTANT: Use drywall anchors when mounting into drywall. ■ Attach the installation brackets to the mounting surface using the 1 " screws provided. Parasol Installation Instructions 191 BACK...
Page 192 If you have an extension pole: Set the extension pole to the correct length, if necessary. ■ Locate the pole lock and press the lock in firmly. ■ Slide the pole extension until it locks in place at the correct length. Parasol Installation Instructions 192 BACK...
Page 193 To Lower the Shade ■ Rotate the crank handle or the extension pole counterclockwise to lower the shade. To Raise the Shade ■ Rotate the crank handle or the extension pole clockwise to raise the shade. Parasol Installation Instructions 193 BACK...
Page 194 Adjust the tension brackets so that the tension cables are parallel to side rails. There is some slack in the drive belt. The drive belt should have some allowable slack when the shade is stacked. Tightening the tension screws will not remove the slack. Parasol Installation Instructions 194 BACK...
Page 195 CAUTION: Do not vacuum XXX fabrics. ■ For deeper cleaning, vacuum gently with a brush attachment. Other cleaning methods described in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning Parasol Installation Instructions 195 BACK...
Page 196 18-67IN-35 Parasol Installation Instructions 196 BACK 3/14...
Page 197 Installation Instructions Parasol Cellular Shades SkyLite w/ Auto-Lift ™ ™ Parasol Installation Instructions 197 BACK...
Page 198 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ■ Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment. Parasol Installation Instructions 198 BACK...
Page 199 Battery Power Cable Battery Wands (For 28 " and Wider Shades) Battery Wands Holder DC Power Supply (Optional) Battery Wand Cover Satellite Battery Pack Battery Wand (For Shades Narrower than 28 ") Battery Power Cable Parasol Installation Instructions 199 BACK...
Page 200 Level (laser level is recommended) ■ Measuring tape and pencil ■ Needle-nose pliers ■ Phillips screwdriver (magnetized screwdriver is recommended) ■ Power drill, " drill bit, and " hex driver ■ Sharp scissors ■ Tape Parasol Installation Instructions 200 BACK...
Page 201 ") Sensor Eye/ or Eye/ Manual nual Satellite Eye Satellite Eye Control Button Button (Optional) (Optional) (In Bottom Rail) om Rail) DC Power DC Power DC Power ower Supply (Optional) Supply (Optional) Supply (Optional) Optional) Parasol Installation Instructions 201 BACK...
Page 202 ■ Slide the moving rail end caps close to the top corner brackets. “L” “R” Top Corner Bracket Moving Rail End Moving Rail End - Left - Right White Grey Bottom Corner Bracket Parasol Installation Instructions 202 BACK...
Page 203 6-Pin Connector 6-pin port on the motor cartridge, located in the Motor Assembly bottom rail on the side of motor assembly. Be sure the plug is oriented correctly. Do not force the connection. 6-Pin Port Parasol Installation Instructions 203 BACK...
Page 204 ■ Repeat the above steps on the right side. ■ If there are more than two tension cables: Make sure all the top tension screw(s) and the top tension plate(s) are in place. Parasol Installation Instructions 204 BACK...
Page 205 Align the left end of the shaft in the bottom rail with the drive gear shaft. ■ Slide the leveling socket onto the shaft and tighten the locking Leveling Sockets collar using the provided " Allen wrench. Locking Collar Parasol Installation Instructions 205 BACK...
Page 206 Align the right end of shaft in the bottom rail with the drive gear shaft. ■ Slide the leveling socket onto the shaft and tighten the locking collar using the provided " Allen wrench. Leveling Sockets Locking Collar Parasol Installation Instructions 206 BACK...
Page 207 Pull the bead chain taut and secure the other end of bead chain in the slot in the bottom right corner bracket. IMPORTANT: Make sure the bead chain is under the tension cable brackets and taut in order to hold the side rails together. Parasol Installation Instructions 207 BACK...
Page 208 Make sure all the tension cables are in the center of the holes in the rail cover. ■ Move the tension cable bracket(s) if necessary. IMPORTANT: Be sure the cover is centered on the bottom rail. Parasol Installation Instructions 208 BACK...
Page 209 Adjust the Tension ■ Remove the tape and tighten all the top tension screws in the top rail until the tension plates line up with the mark. Parasol Installation Instructions 209 BACK...
Page 210 Plug the Power Cable into the Battery Wand ■ Connect the power cable into the both sockets on the battery wands. ■ Make sure the cable is not wrapped around the shaft. ■ Reinstall the bottom rail cover. Proceed to “Test the Shade” Parasol Installation Instructions 210 BACK...
Page 211 Position the battery wand so the power cable is easily connected to the socket. ■ Snap the battery wand into the bracket. Socket ■ Install the battery wand cover with the slot aligned Slot to the socket in the battery wand. Battery Wand Cover Socket Parasol Installation Instructions 211 BACK...
Page 212 If mounted on the wall/ceiling: Secure the power supply cable using wire retainers (not supplied). If hiding the cable behind the shade, make sure it does not impede the operation of the shade. Proceed to “Test the Shade” Parasol Installation Instructions 212 BACK...
Page 213 They can also put small parts in their Supply mouths and CHOKE. WARNING: Electric shock and/or a fire hazard may occur if the DC power supply and cables are not properly installed. Proceed to “Test the Shade” on page 16. Parasol Installation Instructions 213 BACK...
Page 214 After the moving rail is level, slide the leveling socket onto the drive gear shaft and tighten the locking collar. ■ Operate the shade to verify that the shade is level. Repeat the above steps, if necessary. ■ Reinstall the bottom rail cover. Parasol Installation Instructions 214 BACK...
Page 215 Roll the bracket so that the holes touch the side Sill jamb. 1" Installation Brackets ■ Mark and drill the screw holes using a " Jamb drill bit. ■ Attach the installation brackets using the screws provided. Sill Parasol Installation Instructions 215 BACK...
Page 216 Press a cover onto each shade corner, extending them to the window frame to cover the light gap. If you ordered an optional Satellite Eye, proceed to “Mount the Satellite Eye (Optional)” Otherwise proceed to “Operate the Shade” Parasol Installation Instructions 216 BACK...
Page 217 IMPORTANT: You may need another person to assist you with this installation. Attach the Installation Brackets to the Shade ■ Attach the installation brackets to the shade through pre-drilled holes on the side rails using the " screws provided. Parasol Installation Instructions 217 BACK...
Page 218 ■ Attach the installation brackets to the mounting surface using the 1 " screws provided. If you ordered an optional Satellite Eye, proceed to “Mount the Satellite Eye (Optional)” Otherwise proceed to “Operate the Shade” Parasol Installation Instructions 218 BACK...
Page 219 The satellite eye should face down, as shown in the illustration. Hinged Flange ■ After mounting the hinged flange, swivel the satellite eye upward to the correct angle for receiving the signal from the remote control. Parasol Installation Instructions 219 BACK...
Page 220 The shade will move slightly to indicate it has been removed from that group. Note: The wireless wall switch will not be available until 3Q 2014, but we left it in these instructions. If you wish, remove it from this page and the troubleshooting section. Parasol Installation Instructions 220 BACK...
Page 221 This sets the upper motor limit. NOTE: Both upper and lower motor limits have been reset. However, the intermediate stop and all RF programming has been erased and will need to be set up again. Parasol Installation Instructions 221 BACK...
Page 222 Open the battery wand and replace the batteries according to the label on the wand. ■ Use 12 AA Energizer Ultimate Lithium batteries. ■ Reinstall the battery wand into the cover and plug in the power cable. Parasol Installation Instructions 222 BACK...
Page 223 The shade stops before hitting the bottom rail. Problem Solution Adjust the tension brackets so that the tension cables are parallel to side rails. Verify that the side rails are installed in the correct orientation. Parasol Installation Instructions 223 BACK...
Page 224 There is some slack in the drive belt. Problem Solution The drive belt should have some allowable slack when the shade is stacked. Tightening the tension screws will not remove the slack. Parasol Installation Instructions 224 BACK...
Page 225 CAUTION: Do not vacuum XXX fabrics. ■ For deeper cleaning, vacuum gently with a brush attachment. Other cleaning methods described in the branded IOCs include: Compressed Air/Hair Dryer (Cool Setting) Spot-Cleaning Bathtub Cleaning/Water Immersion Ultrasonic Cleaning Injection/Extraction Cleaning Parasol Installation Instructions 225 BACK...
Page 226 18-67IN-36 Parasol Installation Instructions 226 BACK 3/14...
Page 227 Installation Instructions Parasol Cellular Shades SlideArch ™ Parasol Installation Instructions 227 BACK...
Page 228 Product View Arch Trim Top Cord Guide Arch Handle Bottom Rail Installation Brackets Parasol Installation Instructions 228 BACK...
Page 229 Longer #6 Hex Head Screw #6 Flat Head Screw and Screw Hex Head Screw for Use with Spacer Blocks for Use with Common (Provided with Each (Provided) (Not Provided) Headrail End Mounts Extension Bracket) (Provided) Parasol Installation Instructions 229 BACK...
Page 230 If the installation brackets are mounted correctly, the rest of the installation process follows very easily. The Operable Arch can be inside mounted or end mounted. Molding Inside Mount Shade ﬁts within Jamb Jamb window opening. Sill End Mount Shade ﬁts within top of window opening. Parasol Installation Instructions 230 BACK...
Page 231 IMPORTANT: The front edges of the installation brackets must be level and aligned. See Chart See Chart for Depth for Depth Center Center Point Point Standard Bracket Swivel Bracket Parasol Installation Instructions 231 BACK...
Page 232 End Mount ■ Push the end cap back in once the end mount bracket is inserted Bracket all the way into the fabric channels. Rail Parasol Installation Instructions 232 BACK...
Page 233 Rotate the swivel arm to snap the locking tab under the rail. Bracket Lockin In Open ■ The shade is locked when the push tab is against the rail. Position In O Bracket In Locked Position Parasol Installation Instructions 233 BACK...
Page 234 The guide should reach the top casement with the cords taut. Top Cord Guide CAUTION: Do not twist the lift lines going to the top cord guide or the shade will not be able to close all the way. Parasol Installation Instructions 234 BACK...
Page 235 If necessary, adjust the location of the top center cord guide and raise the shade again to check alignment. ■ When the shade operates correctly, drill and fasten the front of the top cord guide with the other screw. Front Screw Parasol Installation Instructions 235 BACK...
Page 236 Shade Operation ■ To close the shade, slide the arch handle to the right. Close ■ To open the shade, slide the arch handle to the left. Open Parasol Installation Instructions 236 BACK...
Page 237 Test the shade operation. After routing the cord into the hole next to the pocket, trim the extra cord under the handle. CAUTION: Do not trim the cord until you are satisfied with the operation of the shade. Parasol Installation Instructions 237 BACK...
Page 238 Test the shade operation. After routing the cord into the hole next to the pocket, trim the extra cord under the handle. CAUTION: Do not trim the cord until you are satisfied with the operation of the shade. Parasol Installation Instructions 238 BACK...
Page 239 Gently push the fabric back into place. Open and close the shade, checking to see if the fabric still rubs. Check the fit after each cut. If needed, repeat the trimming process until the fabric raises and lowers without rubbing. Parasol Installation Instructions 239 BACK...
Page 240 While holding the bottom rail, pull the locking tab to rotate the swivel arm to the open position to release the bottom rail. End Mount Brackets. Screw Holes Locking ■ Reverse the installation procedures. See “Mount Installation Brackets — End Mount” Parasol Installation Instructions 240 BACK...
Page 241 ■ Regular light dusting with a feather duster is all the cleaning that is needed in most circumstances. Vacuuming CAUTION: Do not vacuum XXX fabrics. ■ For deeper cleaning, vacuum gently with a brush attachment. Parasol Installation Instructions 241 BACK...
Page 242 STRANGLE. Always keep cords out of the reach of children. ■ Move cribs, playpens and other furniture away from cords. Children can ■ climb furniture to get to cords. 18-18-67IN-15 Parasol Installation Instructions 242 BACK 3/14...

Lafayette parasol Installation Instructions Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Lafayette parasol

Summary of Contents for Lafayette parasol

Page 176: Manual Operation