IEI Technology eKINO-BT User Manual
  1. Manuals
  2. Brands
  3. IEI Technology Manuals
  4. Motherboard
  5. eKINO-BT
  6. User manual

IEI Technology eKINO-BT User Manual

Mini-itx sbc supports aups sub-system, 22nm intel atom/celeron on-board soc
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
eKINO-BT Mini-ITX SBC
MODEL:
eKINO-BT
Mini-ITX SBC Supports AUPS Sub-System, 22nm Intel® Atom™
or Celeron® SoC, Wide-Range 9 V ~ 26 V DC Input, VGA, Dual
LVDS, Dual GbE, USB 3.0, PCIe Mini, CFast, HD Audio and RoHS

User Manual

Page i
Rev. 1.03 – December 14, 2015

Advertisement

Table of Contents
loading

Related Manuals for IEI Technology eKINO-BT

Summary of Contents for IEI Technology eKINO-BT

  • Page 1: User Manual

    Mini-ITX SBC MODEL: eKINO-BT Mini-ITX SBC Supports AUPS Sub-System, 22nm Intel® Atom™ or Celeron® SoC, Wide-Range 9 V ~ 26 V DC Input, VGA, Dual LVDS, Dual GbE, USB 3.0, PCIe Mini, CFast, HD Audio and RoHS User Manual Page i Rev.
  • Page 2 Mini-ITX SBC Revision Date Version Changes December 14, 2015 1.03 Added a note in Section 3.3.6: VGA Connector February 13, 2015 1.02 Changed power input voltage range to 9 V ~ 26 V January 23, 2015 1.01 Updated part number of the SATA cable September 24, 2014 1.00...
  • Page 3 Mini-ITX SBC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
  • Page 4 Mini-ITX SBC Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.
  • Page 5 Mini-ITX SBC Table of Contents 1 INTRODUCTION......................1 1.1 I ......................2 NTRODUCTION 1.2 M ....................3 ODEL ARIATIONS 1.3 F ........................3 EATURES 1.4 C ......................4 ONNECTORS 1.5 D ....................... 6 IMENSIONS 1.6 D ........................ 7 1.7 T ..................
  • Page 6 Mini-ITX SBC 3.2.11 Front Panel Connector................... 29 3.2.12 Infrared Interface Connector ................. 30 3.2.13 Keyboard and Mouse Connector ..............31 3.2.14 LAN Active LED Connector................32 3.2.15 LVDS Connectors................... 33 3.2.16 microSD Card Slot (E38XX SKU Only)............35 3.2.17 PCIe x1 Slot ....................35 3.2.18 PCIe Mini Card Slot ..................
  • Page 7 Mini-ITX SBC 4.7 S ..................66 YSTEM ONFIGURATION 4.7.1 AT/ATX Power Mode Selection................ 66 4.7.2 Battery Enable/Disable..................66 4.7.3 Clear CMOS Button..................68 4.7.4 LVDS Panel Type Selection................68 4.7.5 LVDS1 Voltage Selection.................. 70 4.7.6 LVDS2 Voltage Selection.................. 71 4.7.7 UPS/Battery Mode Selection................
  • Page 8 Mini-ITX SBC 5.3.5 Serial Port Console Redirection ..............98 5.3.6 CPU Configuration..................100 5.3.7 IDE Configuration ..................102 5.3.8 Trusted Computing..................103 5.3.9 USB Configuration..................104 5.4 C ......................... 105 HIPSET 5.4.1 North Bridge ....................106 5.4.1.1 Intel IGD Configuration................106 5.4.2 Southbridge Configuration ................
  • Page 9 Figure 1-1: eKINO-BT ........................2 Figure 1-2: Connectors (Front Side) .....................4 Figure 1-3: Connectors (Solder Side) ...................5 Figure 1-4: eKINO-BT Dimensions (mm) ..................6 Figure 1-5: Data Flow Diagram......................7 Figure 3-1: Peripheral Interface Connectors (Front Side) ............16 Figure 3-2: Peripheral Interface Connectors (Solder Side) ............17 Figure 3-3: 9 V ~ 26 V Power Connector Location ..............20...
  • Page 10 Mini-ITX SBC Figure 3-26: RS-422/485 Serial Port Connector Location............43 Figure 3-27: SMBus Connector Location ...................44 Figure 3-28: SO-DIMM Connector Locations ................45 Figure 3-29: SPI Flash Connector Location................46 Figure 3-30: EC SPI Flash Connector Location.................47 Figure 3-31: TPM Connector Location..................48 Figure 3-32: USB Connector Location..................49...
  • Page 11 Mini-ITX SBC Figure 4-22: USB Connector......................79 Figure 4-23: VGA Connector .......................80 Figure 6-1: Driver CD Main Menu ..................... 116 Figure 6-2: Available Drivers ....................116 Figure 6-3: Chipset Driver Welcome Screen................117 Figure 6-4: Chipset Driver License Agreement ..............118 Figure 6-5: Chipset Driver Read Me File .................
  • Page 12 Mini-ITX SBC List of Tables Table 1-1: Model Variations ......................3 Table 1-2: Technical Specifications....................10 Table 2-1: Packing List.........................13 Table 2-2: Optional Items......................14 Table 3-1: Peripheral Interface Connectors ................18 Table 3-2: Rear Panel Connectors ....................19 Table 3-3: 9 V ~ 26 V Power Connector Pinouts................20 Table 3-4: 12-pin Battery Connector Pinouts ................21...
  • Page 13 Mini-ITX SBC Table 3-27: USB 2.0 Port Connector Pinouts................49 Table 3-28: 9 V ~ 26 V DC In Connector Pinouts ...............50 Table 3-29: LAN Pinouts ......................51 Table 3-30: Ethernet Connector LEDs ..................51 Table 3-31: External USB 2.0 Port Pinouts ................52 Table 3-32: LAN Pinouts ......................52...
  • Page 14 Mini-ITX SBC BIOS Menus BIOS Menu 1: Main ........................84 BIOS Menu 2: Advanced ......................85 BIOS Menu 3: ACPI Settings .......................86 BIOS Menu 4: F81866 Super IO Configuration ................87 BIOS Menu 5: Serial Port n Configuration Menu...............87 BIOS Menu 6: IrDA Configuration Menu..................92 BIOS Menu 7: iWDD H/W Monitor ....................94...

  • Page 15: Introduction

    Mini-ITX SBC Chapter Introduction Page 1...

  • Page 16: I Ntroduction

    Mini-ITX SBC 1.1 Introduction Figure 1-1: eKINO-BT The eKINO-BT is a Mini-ITX SBC that supports AUPS sub-system. It has an on-board 22nm Intel® Atom™ or Celeron® SoC, and supports one or two 204-pin 1333/1066 MHz unbuffered DDR3L SDRAM SO-DIMMs.

  • Page 17: M Odel V Ariations

    Mini-ITX SBC 1.2 Model Variations The model variations for the eKINO-BT series are listed in Table 1-1. On-board SoC Model Name Clock Speed # of Cores L2 Cache Max TDP EKINO-BT-J19001 Intel® Celeron® J1900 2.0 GHz 2 MB 10 W EKINO-BT-N29301 Intel®...

  • Page 18: C Onnectors

    Mini-ITX SBC 1.4 Connectors The connectors on the eKINO-BT are shown in the figures below. Figure 1-2: Connectors (Front Side) Page 4...

  • Page 19: Figure 1-3: Connectors (Solder Side)

    Mini-ITX SBC Figure 1-3: Connectors (Solder Side) Page 5...

  • Page 20: D Imensions

    Mini-ITX SBC 1.5 Dimensions The main dimensions of the eKINO-BT are shown in the diagram below. Figure 1-4: eKINO-BT Dimensions (mm) Page 6...

  • Page 21: Data Flow

    Mini-ITX SBC 1.6 Data Flow Figure 1-5 shows the data flow between the system chipset, the CPU and other components installed on the motherboard. Figure 1-5: Data Flow Diagram Page 7...

  • Page 22: Technical Specifications

    One VGA (up to 2560x1600@60 Hz) Two 18/24-bit dual-channel LVDS* by CH7511B DP to LVDS converters Display Output (up to 1920x1200@60 Hz) * The eKINO-BT supports only one LCD when using the optional 7.4 V battery (BATKIT-2S2P3800-R10/BAT-LI-2S2P3800). AMI UEFI BIOS BIOS...
  • Page 23 Mini-ITX SBC Super I/O Controller Fintek F81866D-I ITE IT8528E Embedded Controller Watchdog Timer Software programmable, supports 1~255 sec. system reset One full-size/half-size PCIe Mini card slot (with USB 2.0 signal) One PCIe x1 slot Expansions One CFast card slot...

  • Page 24: Table 1-2: Technical Specifications

    Mini-ITX SBC Environmental and Power Specifications Input voltage range: 9 V ~ 26 V Recommended operating input voltage range: 12 V ~ 24 V Power Supply One external 4-pin DIN DC jack One internal 4-pin (2x2) power connector +12V@1.55A (Intel® Celeron® J1900 CPU with two 4 GB 1333 MHz...

  • Page 25: Packing List

    Mini-ITX SBC Chapter Packing List Page 11...

  • Page 26: Unpacking Precautions

    Only handle the edges of the PCB: Don't touch the surface of the motherboard. Hold the motherboard by the edges when handling. 2.2 Unpacking Precautions When the eKINO-BT is unpacked, please do the following: Follow the anti-static guidelines above. Make sure the packing box is facing upwards when opening.

  • Page 27: Packing List

    If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the eKINO-BT was purchased from or contact an IEI sales representative directly by sending an email to sales@ieiworld.com.

  • Page 28: Optional Items

    2S2P smart battery (7.4 V, 3800 mAh) (P/N: BAT-LI-2S2P3800) RS-422/485 cable (P/N: 32205-003800-300-RS) PS/2 keyboard and mouse Y cable (P/N: 32006-000300-100-RS) Table 2-2: Optional Items NOTE: The eKINO-BT supports only one LCD when using the optional 7.4 V battery (BATKIT-2S2P3800-R10/BAT-LI-2S2P3800). Page 14...

  • Page 29: Connectors

    Mini-ITX SBC Chapter Connectors Page 15...

  • Page 30: Peripheral Interface Connectors

    Mini-ITX SBC 3.1 Peripheral Interface Connectors This chapter details all the peripheral interface connectors. 3.1.1 Layout The figures below show all the peripheral interface connectors. Figure 3-1: Peripheral Interface Connectors (Front Side) Page 16...

  • Page 31: Peripheral Interface Connectors

    Mini-ITX SBC Figure 3-2: Peripheral Interface Connectors (Solder Side) 3.1.2 Peripheral Interface Connectors The table below shows a list of the peripheral interface connectors on the eKINO-BT. Detailed descriptions of these connectors can be found below. Connector Type Label...

  • Page 32: Table 3-1: Peripheral Interface Connectors

    Mini-ITX SBC Connector Type Label Digital I/O connector 10-pin header DIO1 Fan connector (CPU) 4-pin wafer CPU_FAN1 Fan connector (system) 3-pin wafer SYS_FAN1 Front panel connector 14-pin header F_PANEL1 Infrared connector 5-pin header Keyboard and mouse connector 6-pin wafer...

  • Page 33: External Interface Panel Connectors

    Mini-ITX SBC 3.1.3 External Interface Panel Connectors The table below lists the rear panel connectors on the eKINO-BT. Detailed descriptions of these connectors can be found in a later section. Connector Type Label 9 V ~ 26 V DC in connector...

  • Page 34: Pin Battery Connector

    The 12-pin battery connector allows connection of the AUPS battery. When the AUPS battery is installed to the system, a battery icon will be shown on the Windows notification area. NOTE: The eKINO-BT supports only one LCD when using the optional 7.4 V battery (BATKIT-2S2P3800-R10/BAT-LI-2S2P3800). Page 20...

  • Page 35: Audio Connector

    Mini-ITX SBC Figure 3-4: 12-pin Battery Connector Location Description VBAT VBAT VBAT VBAT BAT_SMBCLK BAT_SMBDATA BAT_TH BAT ID Table 3-4: 12-pin Battery Connector Pinouts 3.2.3 Audio Connector CN Label: AUDIO2 CN Type: 10-pin header CN Location: See Figure 3-5...

  • Page 36: Backlight Inverter Connectors

    Mini-ITX SBC This connector connects to speakers, a microphone and an audio input. Figure 3-5: Audio Connector Location Description Description LMIC2-L ANALOG GND LMIC2-R PRESENCE# LLINE2-R MIC2-JD FRONT-IO LLINE2-L LINE2-JD Table 3-5: Audio Connector Pinouts 3.2.4 Backlight Inverter Connectors...

  • Page 37: Battery Connector

    Mini-ITX SBC Figure 3-6: Backlight Inverter Connector Locations Description LCD_BKLTCTL GROUND +12V GROUND BACKLIGHT ENABLE Table 3-6: Backlight Inverter Connector Pinouts 3.2.5 Battery Connector CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery.

  • Page 38: Battery Led Connector

    Mini-ITX SBC CN Label: BAT1 CN Type: 2-pin wafer CN Location: See Figure 3-7 CN Pinouts: See Table 3-7 This is connected to the system battery. The battery provides power to the system clock to retain the time when power is turned off.

  • Page 39: Cfast Card Slot

    Mini-ITX SBC Figure 3-8: Battery LED Connector Location Description VCC5 DISCHARGING LED VCC5 CHARGING LED VCC5 DC IN LED Table 3-8: Battery LED Connector Pinouts 3.2.7 CFast Card Slot CN Label: CFAST1 CN Type: CFast card slot CN Location: See Figure 3-9 The CFast card slot is for installing a CFast card to the system.

  • Page 40: Digital I/O Connector

    Mini-ITX SBC Figure 3-9: CFast Card Slot Location 3.2.8 Digital I/O Connector CN Label: DIO1 10-pin header CN Type: CN Location: See Figure 3-10 CN Pinouts: See Table 3-9 The digital I/O connector provides programmable input and output for external devices.

  • Page 41: Fan Connector (Cpu)

    Mini-ITX SBC Figure 3-10: Digital I/O Connector Location Description Description +V5S Output 3 Output 2 Output 1 Output 0 Input 3 Input 2 Input 1 Input 0 Table 3-9: Digital I/O Connector Pinouts 3.2.9 Fan Connector (CPU) CN Label:...

  • Page 42: Fan Connector (System)

    Mini-ITX SBC Figure 3-11: CPU Fan Connector Location Description +V12S Rotation Signal PWM Control Signal Table 3-10: CPU Fan Connector Pinouts 3.2.10 Fan Connector (System) CN Label: SYS_FAN1 3-pin wafer CN Type: CN Location: See Figure 3-12 CN Pinouts: See Table 3-11 The fan connector attaches to a system cooling fan.

  • Page 43: Front Panel Connector

    Mini-ITX SBC Figure 3-12: System Fan Connector Location Description Rotation Signal +12V Table 3-11: System Fan Connector Pinouts 3.2.11 Front Panel Connector CN Label: F_PANEL1 14-pin header CN Type: CN Location: See Figure 3-13 CN Pinouts: See Table 3-12 The front panel connector connects to the indicator LEDs and buttons on the computer's front panel.

  • Page 44: Infrared Interface Connector

    Mini-ITX SBC Figure 3-13: Front Panel Connector Location Function Description Function Description LED_PWR BEEP_PWR Power LED Buzzer PWR_BTN PC_BEEP# Power Button HDD_LED+ Reset RESET HDD LED HDD_LED- Table 3-12: Front Panel Connector Pinouts 3.2.12 Infrared Interface Connector CN Label:...

  • Page 45: Keyboard And Mouse Connector

    Mini-ITX SBC Figure 3-14: Infrared Connector Location Description +V5X IR-RX IR-TX Table 3-13: Infrared Connector Pinouts 3.2.13 Keyboard and Mouse Connector CN Label: KB_MS1 CN Type: 6-pin wafer CN Location: See Figure 3-15 See Table 3-14 CN Pinouts: The keyboard and mouse connector connects to a PS/2 Y-cable that can be connected to a PS/2 keyboard and mouse.

  • Page 46: Lan Active Led Connector

    Mini-ITX SBC Figure 3-15: Keyboard and Mouse Connector Location Description VCC5_KBMS Mouse Data Mouse Clock Keyboard Data Keyboard Clock Table 3-14: Keyboard and Mouse Connector Pinouts 3.2.14 LAN Active LED Connector CN Label: LAN_ LED1 4-pin header CN Type:...

  • Page 47: Lvds Connectors

    30-pin crimp CN Location: See Figure 3-17 CN Pinouts: See Table 3-16 The LVDS connectors are for LCD panels connected to the board. NOTE: The eKINO-BT supports only one LCD when using the optional 7.4 V battery (BATKIT-2S2P3800-R10/BAT-LI-2S2P3800) Page 33...

  • Page 48: Figure 3-17: Lvds Connector Locations

    Mini-ITX SBC Figure 3-17: LVDS Connector Locations Description Description LVDS_A_TX0-P LVDS_A _TX0-N LVDS_A_TX1-P LVDS_A _TX1-N LVDS_A_TX2-P LVDS_A _TX2-N LVDS_A_TXCLK-P LVDS_A _TXCLK-N LVDS_A_TX3-P LVDS_A _TX3-N LVDS_B _TX0-P LVDS_B _TX0-N LVDS_B _TX1-P LVDS_B _TX1-N LVDS_B _TX2-P LVDS_B _TX2-N LVDS_B _TXCLK-P LVDS_B _TXCLK-N...

  • Page 49: Microsd Card Slot (E38Xx Sku Only)

    Mini-ITX SBC 3.2.16 microSD Card Slot (E38XX SKU Only) CN Label: MICROSD1 microSD card slot CN Type: CN Location: See Figure 3-18 The microSD card slot is for installing a microSD card to the system. Figure 3-18: microSD Card Slot Location 3.2.17 PCIe x1 Slot...

  • Page 50: Pcie Mini Card Slot

    Mini-ITX SBC Figure 3-19: PCIe x1 Slot Location 3.2.18 PCIe Mini Card Slot CN Label: M_PCIE1 CN Type: PCIe Mini card slot CN Location: See Figure 3-20 CN Pinouts: See Table 3-17 The PCIe Mini card slot enables a full-size/half-size PCIe Mini card expansion module to be connected to the board.

  • Page 51: Table 3-17: Pcie Mini Card Slot Pinouts

    Mini-ITX SBC Description Description PCIE_WAKE# VCC3 1.5V CLK- CLK+ PCIRST# VCC3 PCIRST# PERN2 3VDual PERP2 1.5V SMBCLK PETN2 SMBDATA PETP2 USBD- USBD+ 1.5V VCC3 Table 3-17: PCIe Mini Card Slot Pinouts Page 37...

  • Page 52: Power Button (On-Board)

    3.2.19 Power Button (On-board) CN Label: PWR_SW1 Push button CN Type: CN Location: See Figure 3-21 Push the on-board power button to power on the eKINO-BT. Figure 3-21: On-board Power Button Location 3.2.20 Reset Button (On-board) CN Label: RST_SW1 CN Type: Push button...

  • Page 53: Sata 3Gb/S Drive Connectors

    Mini-ITX SBC Figure 3-22: On-board Reset Button Location 3.2.21 SATA 3Gb/s Drive Connectors CN Label: SATA1, SATA2 CN Type: 7-pin SATA connector CN Location: See Figure 3-23 CN Pinouts: See Table 3-18 The SATA drive connectors can be connected to SATA drives and support up to 3Gb/s data transfer rate.

  • Page 54: Figure 3-23: Sata 3Gb/S Drive Connector Locations

    Mini-ITX SBC Figure 3-23: SATA 3Gb/s Drive Connector Locations Description Table 3-18: SATA 3Gb/s Drive Connector Pinouts Page 40...

  • Page 55: Sata Power Connectors (5 V)

    Mini-ITX SBC 3.2.22 SATA Power Connectors (5 V) CN Label: SATA_PWR1, SATA_PWR2 2-pin wafer CN Type: CN Location: See Figure 3-24 CN Pinouts: See Table 3-19 Use the SATA power connector to connect to SATA device power connections. Figure 3-24: 5 V SATA Power Connector Locations...

  • Page 56: Serial Port Connector, Rs-422/485

    Mini-ITX SBC Figure 3-25: RS-232 Serial Port Connector Location Description Description -NDCD2 -NDSRs NSIN2 -NRTS2 NSOUT2 -NCTS2 -NDTR2 -XRI2 Table 3-20: RS-232 Serial Port Connector Pinouts 3.2.24 Serial Port Connector, RS-422/485 CN Label: COM5 CN Type: 4-pin wafer CN Location:...

  • Page 57: Figure 3-26: Rs-422/485 Serial Port Connector Location

    Mini-ITX SBC Figure 3-26: RS-422/485 Serial Port Connector Location Description RXD422- RXD422+ TXD422+/TXD485+ TXD422-/TXD485- Table 3-21: RS-422/485 Serial Port Connector Pinouts Use the optional RS-422/485 cable to connect to a serial device. The pinouts of the DB-9 connector are listed below.

  • Page 58: Smbus Connector

    Mini-ITX SBC 3.2.25 SMBus Connector CN Label: SMBUS1 4-pin wafer CN Type: CN Location: See Figure 3-27 CN Pinouts: See Table 3-23 The SMBus (System Management Bus) connector provides low-speed system management communications. Figure 3-27: SMBus Connector Location Description...

  • Page 59: Spi Flash Connector

    Mini-ITX SBC The SO-DIMM connectors are for installing SO-DIMMs on the system. NOTE: Use DIMM1 slot when installing one SO-DIMM. Figure 3-28: SO-DIMM Connector Locations 3.2.27 SPI Flash Connector CN Label: JSPI1 CN Type: 6-pin wafer See Figure 3-29...

  • Page 60: Spi Flash Connector (Ec)

    Mini-ITX SBC Figure 3-29: SPI Flash Connector Location Description +V3.3M_SPI_CON SPI_CS SPI_SO_SW SPI_CLK_SW SPI_SI_SW Table 3-24: SPI Flash Connector Pinouts 3.2.28 SPI Flash Connector (EC) CN Label: JSPI2 6-pin wafer CN Type: CN Location: See Figure 3-30 CN Pinouts: See Table 3-25 The SPI flash connector is used to flash the EC ROM.

  • Page 61: Tpm Connector

    Mini-ITX SBC Figure 3-30: EC SPI Flash Connector Location Description +V3.3M_SPI_CON_EC SPI_CS_EC SPI_SO_SW_EC SPI_CLK_SW_EC SPI_SI_SW_EC Table 3-25: EC SPI Flash Connector Pinouts 3.2.29 TPM Connector CN Label: TPM1 20-pin header CN Type: CN Location: See Figure 3-31 CN Pinouts: See Table 3-26 The TPM connector connects to a TPM module.

  • Page 62: Usb 2.0 Connector

    Mini-ITX SBC Figure 3-31: TPM Connector Location Description Description LCLK LFRAME# LRERST# LAD3 LAD2 LAD1 LAD0 SB3V SERIRQ GLKRUN# LPCPD# LDRQ# Table 3-26: TPM Connector Pinouts 3.2.30 USB 2.0 Connector CN Label: USB1 CN Type: 8-pin header CN Location:...

  • Page 63: E Xternal I Nterface C Onnectors

    Mini-ITX SBC Figure 3-32: USB Connector Location Description Description DATA- DATA+ DATA+ DATA- Table 3-27: USB 2.0 Port Connector Pinouts 3.3 External Interface Connectors The figure below shows the external peripheral interface connector (EPIC) panel. The EPIC panel consists of the following:...

  • Page 64: Audio Jacks

    Mini-ITX SBC 3.3.1 9 V ~ 26 V DC In Connector CN Label: SPWR_IN1 4-pin mini-DIN CN Type: CN Location: See Figure 3-33 CN Pinouts: See Table 3-36 The power connector connects to the 9 V ~ 26 V DC power adapter.

  • Page 65: Ethernet And Usb 2.0 Connectors

    Table 3-29: LAN Pinouts Figure 3-36: Ethernet Connector Description Description on: linked off: 10 Mb/s blinking: data is being sent/received green: 100 Mb/s orange: 1000 Mb/s Table 3-30: Ethernet Connector LEDs The eKINO-BT has two external USB 2.0 ports. Page 51...

  • Page 66: Ethernet And Usb 3.0 Connectors

    Mini-ITX SBC Description VBUS Table 3-31: External USB 2.0 Port Pinouts 3.3.4 Ethernet and USB 3.0 Connectors CN Label: LAN_USB1 RJ-45 and USB 3.0 connector CN Type: CN Location: See Figure 3-33 CN Pinouts: See Table 3-32 and Table 3-34 The LAN connector connects to a local network.

  • Page 67: Serial Port Connectors

    Mini-ITX SBC Description Description on: linked off: 10 Mb/s blinking: data is being sent/received green: 100 Mb/s orange: 1000 Mb/s Table 3-33: Ethernet Connector LEDs The eKINO-BT has two external USB 3.0 ports. Description VBUS GND1 STDA_SSRX1_N STDA_SSRX1_P GND_DRAIN STDA_SSTX1_N STDA_SSTX1_P Table 3-34: External USB 3.0 Port Pinouts...

  • Page 68: Vga Connector

    Mini-ITX SBC Description Description DATA TERMINAL READY (DTR1) RING INDICATOR (RI1) Table 3-35: Serial Port Pinouts Figure 3-38: Serial Port Pinouts 3.3.6 VGA Connector CN Label: VGA1 CN Type: 15-pin female CN Location: See Figure 3-33 CN Pinouts: See Table 3-36 and Figure 3-39 The VGA connector connects to a monitor that accepts a standard VGA input.

  • Page 69: Figure 3-39: Vga Connector

    After installing Intel® graphics driver, the two LVDS ports will be set to the primary display output ports and the VGA port will be disabled. The reason for this is the eKINO-BT uses two CH7511B chips to convert DP to LVDS and Intel® graphics driver recognizes the chips and the two LVDS ports as two devices.

  • Page 70: Installation

    Mini-ITX SBC Chapter Installation Page 56...

  • Page 71: Installation Considerations

    Electrostatic discharge (ESD) can cause serious damage to electronic components, including the eKINO-BT. Dry climates are especially susceptible to ESD. It is therefore critical to strictly adhere to the following anti-static precautions whenever the eKINO-BT, or any other electrical component, is handled.
  • Page 72 Mini-ITX SBC WARNING: The installation instructions described in this manual should be carefully followed in order to prevent damage to the eKINO-BT, eKINO-BT components and injury to the user. Before and during the installation please DO the following: Read the user manual: The user manual provides a complete description of the installation instructions and configuration options.

  • Page 73: So-Dimm I Nstallation

    Figure 3-28. Figure 4-1: SO-DIMM Installation Step 1: Locate the SO-DIMM socket on the solder side of the eKINO-BT. Place the board on an anti-static mat. Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the notch on the memory socket.

  • Page 74: Figure 4-2: Removing The Retention Screws

    Mini-ITX SBC Step 2: Remove the retention screws. Remove the two retention screws as shown in Figure 4-2. Figure 4-2: Removing the Retention Screws Step 3: Insert into the socket at an angle. Line up the notch on the card with the notch on the slot.

  • Page 75: Half-Size Pcie Mini Card Installation

    Mini-ITX SBC Step 4: Secure the full-size PCIe Mini card. Secure the full-size PCIe Mini card with the retention screws previously removed (Figure 4-4). Figure 4-4: Securing the Full-size PCIe Mini Card 4.5 Half-size PCIe Mini Card Installation The PCIe Mini card slot allows installation of either a full-size or half-size PCIe Mini card.

  • Page 76: Figure 4-5: Removing The Retention Screw

    Mini-ITX SBC Figure 4-5: Removing the Retention Screw Step 3: Remove the standoff. Unscrew and remove the standoff secured on the motherboard as shown in Figure 4-6. Figure 4-6: Removing the Standoff Page 62...

  • Page 77: Figure 4-7: Installing The Standoff

    Mini-ITX SBC Step 4: Install the standoff to the screw hole for the half-size PCIe Mini card. Install the previously removed standoff to the screw hole for the half-size PCIe Mini card (Figure 4-7). Figure 4-7: Installing the Standoff Step 5: Insert into the socket at an angle.

  • Page 78: Figure 4-8: Inserting The Half-Size Pcie Mini Card Into The Slot At An Angle

    Mini-ITX SBC Figure 4-8: Inserting the Half-size PCIe Mini Card into the Slot at an Angle Step 6: Secure the half-size PCIe Mini card. Secure the half-size PCIe Mini card with the retention screw previously removed (Figure 4-9). Step 0:...

  • Page 79: Ups I Nstallation

    Mini-ITX SBC 4.6 UPS Installation To install the UPS, connect the AUPS battery to the motherboard and connect the motherboard to the 9 V ~ 26 V power supply. NOTE: A battery icon will be shown on the Windows notification area when the AUPS battery is installed to the system.

  • Page 80: System Configuration

    Mini-ITX SBC 4.7 System Configuration The system configuration is controlled by buttons/jumpers/switches, and should be performed before installation. 4.7.1 AT/ATX Power Mode Selection The AT and ATX power mode selection is made through the AT/ATX power mode switch which is shown in Figure 4-11.

  • Page 81: Figure 4-12: Battery Enable/Disable Jumper Location

    Mini-ITX SBC When this jumper is closed, the system will use the battery when needed; when open, the system will not use the battery. Setting Description Closed Enable battery (Default) Open Disable battery Table 4-2: Battery Enable/Disable Jumper Settings...

  • Page 82: Clear Cmos Button

    Mini-ITX SBC 4.7.3 Clear CMOS Button To reset the BIOS, remove the on-board battery and press the clear CMOS button for three seconds or more. The clear CMOS button location is shown in Figure 4-13. Figure 4-13: Clear CMOS Button Location 4.7.4 LVDS Panel Type Selection...

  • Page 83: Figure 4-14: Lvds Panel Type Selection Switch Locations

    Mini-ITX SBC * ON=0, OFF=1; Single=S, Dual=D SW1 (4-3-2-1) Description 0000 800x600 18-bit S (default) 0001 1024x768 18-bit S 0010 1024x768 24-bit S 0011 1280x768 18-bit S 0100 1280x800 18-bit S 0101 1280x960 18-bit S 0110 1280x1024 24-bit D...

  • Page 84: Lvds1 Voltage Selection

    Mini-ITX SBC 4.7.5 LVDS1 Voltage Selection WARNING: Permanent damage to the screen and eKINO-BT may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that came with the monitor to select the correct voltage.

  • Page 85: Lvds2 Voltage Selection

    Mini-ITX SBC 4.7.6 LVDS2 Voltage Selection WARNING: Permanent damage to the screen and eKINO-BT may occur if the wrong voltage is selected with this jumper. Please refer to the user guide that came with the monitor to select the correct voltage.

  • Page 86: Ups/Battery Mode Selection

    Mini-ITX SBC 4.7.7 UPS/Battery Mode Selection Jumper Label: J_UPS1 3-pin header Jumper Type: Jumper Settings: See Table 4-6 Jumper Location: See Figure 4-17 This jumper sets the system to run off the battery exclusively, or to use the battery as a UPS.

  • Page 87: Table 4-7: In At Power Mode

    Mini-ITX SBC The power behavior of the UPS and battery modes might be different in the AT and ATX power modes. Refer to Table 4-7 and Table 4-8 for differences. Power Supply UPS Mode Battery Mode The system can’t be...

  • Page 88: C Hassis I Nstallation

    This section outlines the installation of peripheral devices to the onboard connectors. 4.9.1 SATA Drive Connection The eKINO-BT is shipped with two SATA drive cables. To connect the SATA drive to the connector, please follow the steps below. Step 1: Locate the SATA connector and the SATA power connector.

  • Page 89: E Xternal P Eripheral I Nterface C Onnection

    Devices can be connected to the external connectors. To install external devices, follow the directions in the subsections below. 4.10.1 Audio Connector The audio jacks on the external audio connector enable the eKINO-BT to be connected to a stereo sound setup. To install the audio devices, follow the steps below. Step 1: Identify the audio plugs.

  • Page 90: Lan Connection

    Locate the RJ-45 connectors. The locations of the RJ-45 connectors are shown in Chapter 3. Step 2: Align the connectors. Align the RJ-45 connector on the LAN cable with one of the RJ-45 connectors on the eKINO-BT. See Figure 4-20. Page 76...

  • Page 91: Serial Device Connection

    RJ-45 connector into the on-board RJ-45 connector. Step 0: 4.10.3 Serial Device Connection The eKINO-BT has three male DB-9 connectors on the external peripheral interface panel for three serial devices. Follow the steps below to connect a serial device to the eKINO-BT.

  • Page 92: Usb Connection

    4.10.4 USB Connection The external USB 2.0/3.0 connectors provide easier and quicker access to external USB devices. Follow the steps below to connect USB devices to the eKINO-BT. Step 1: Locate the USB 2.0/3.0 connectors. The locations of the USB 2.0/3.0 connectors are shown in Chapter 3.

  • Page 93: Vga Monitor Connection

    Figure 4-22: USB Connector 4.10.5 VGA Monitor Connection The eKINO-BT has a single female DB-15 connector on the external peripheral interface panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor to the eKINO-BT, please follow the instructions below.

  • Page 94: Figure 4-23: Vga Connector

    Mini-ITX SBC Figure 4-23: VGA Connector Step 4: Secure the connector. Secure the DB-15 VGA connector from the VGA monitor to the external interface by tightening the two retention screws on either side of the connector. Step 0: Page 80...
  • Page 95 Mini-ITX SBC Chapter BIOS Page 81...

  • Page 96: I Ntroduction

    Mini-ITX SBC 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.

  • Page 97: Getting Help

    Mini-ITX SBC Function Page Up key Move to the next page Page Dn key Move to the previous page Esc key Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu --...

  • Page 98: Main

    Mini-ITX SBC The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above. 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.

  • Page 99: A Dvanced

    Mini-ITX SBC System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus:...

  • Page 100: Acpi Settings

    Mini-ITX SBC 5.3.1 ACPI Settings The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and Power Interface (ACPI) options. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced ACPI Settings Select the highest ACPI sleep state the system...

  • Page 101: F81866 Super Io Configuration

    Mini-ITX SBC 5.3.2 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu (BIOS Menu 4) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced F81866 Super IO Configuration...
  • Page 102 Mini-ITX SBC 5.3.2.1.1 Serial Port 1 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disabled Disable the serial port Enable the serial port Enabled EFAULT Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
  • Page 103 Mini-ITX SBC Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address. Auto The serial port IO port address and interrupt address EFAULT are automatically detected. Serial Port I/O port address is 2F8h and the interrupt IO=2F8h;...
  • Page 104 Mini-ITX SBC IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=10 address is IRQ10 Serial Port I/O port address is 3F8h and the interrupt IO=3F8h; address is IRQ10, 11 IRQ=10, 11 IO=2F8h; Serial Port I/O port address is 2F8h and the interrupt...
  • Page 105 Mini-ITX SBC IO=2F8h; Serial Port I/O port address is 2F8h and the interrupt IRQ=10, 11 address is IRQ10, 11 Serial Port I/O port address is 3E8h and the interrupt IO=3E8h; address is IRQ10, 11 IRQ=10, 11 IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt...

  • Page 106: Irda Configuration

    Mini-ITX SBC IO=2E8h; Serial Port I/O port address is 2E8h and the interrupt IRQ=10, 11 address is IRQ10, 11 Serial Port I/O port address is 2D0h and the interrupt IO=2D0h; address is IRQ10, 11 IRQ=10, 11 IO=2E0h; Serial Port I/O port address is 2E0h and the interrupt...
  • Page 107 Mini-ITX SBC Auto The serial port IO port address and interrupt address EFAULT are automatically detected. Serial Port I/O port address is 2E0h and the interrupt IO=2E0h; address is IRQ11 IRQ=11 IO=3F8h; Serial Port I/O port address is 3F8h and the interrupt...

  • Page 108: Iwdd H/W Monitor

    Mini-ITX SBC 5.3.3 iWDD H/W Monitor The iWDD H/W Monitor menu (BIOS Menu 7) displays the system temperatures and voltages. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced PC Health Status Smart Fan Mode Select CPU temperature...

  • Page 109: Smart Fan Mode Configuration

    Mini-ITX SBC +DDR +5VSB +3.3V +3.3VSB 5.3.3.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 8) to configure smart fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc.

  • Page 110: Rtc Wake Settings

    Mini-ITX SBC Manual Mode The fan spins at the speed set in Manual Mode settings. The fan adjusts its speed using Auto Mode Auto Mode EFAULT settings. Auto mode fan start/off temperature Use the + or – key to change the Auto mode fan start/off temperature value. Enter a decimal number between 1 and 100.

  • Page 111: Bios Menu 9: Rtc Wake Settings

    Mini-ITX SBC Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the date::hr::min::sec specified ---------------------- : Select Screen ↑...

  • Page 112: Serial Port Console Redirection

    Mini-ITX SBC 5.3.5 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 10) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port.
  • Page 113 Mini-ITX SBC Terminal Type [ANSI] Use the Terminal Type option to specify the remote terminal type. The target terminal type is VT100 VT100 VT100+ The target terminal type is VT100+ VT-UTF8 The target terminal type is VT-UTF8 ANSI The target terminal type is ANSI...

  • Page 114: Cpu Configuration

    Mini-ITX SBC The parity bit is 0 if the number of ones in the data bits is odd. The parity bit is always 1. This option does not Mark provide error detection. Space The parity bit is always 0. This option does not provide error detection.
  • Page 115 Mini-ITX SBC The CPU Configuration menu (BIOS Menu 11) lists the following CPU details: CPU Signature: Lists the CPU signature value. Microcode Patch: Lists the microcode patch being used. Max CPU Speed: Lists the maximum CPU processing speed. Min CPU Speed: Lists the minimum CPU processing speed.

  • Page 116: Ide Configuration

    Mini-ITX SBC 5.3.7 IDE Configuration Use the IDE Configuration menu (BIOS Menu 12) to view the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced IDE Configuration Enable/Disable Serial Serial-ATA (SATA)

  • Page 117: Trusted Computing

    Mini-ITX SBC 5.3.8 Trusted Computing Use the Trusted Computing menu (BIOS Menu 13) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM). Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced Configuration...

  • Page 118: Usb Configuration

    Mini-ITX SBC 5.3.9 USB Configuration Use the USB Configuration menu (BIOS Menu 14) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Advanced USB Configuration Enables Legacy USB support.

  • Page 119: C Hipset

    Mini-ITX SBC Enabled Legacy USB support enabled EFAULT Legacy USB support disabled Disabled Auto Legacy USB support disabled if no USB devices are connected 5.4 Chipset Use the Chipset menu (BIOS Menu 15) to access the Northbridge and Southbridge configuration menus.

  • Page 120: North Bridge

    Mini-ITX SBC 5.4.1 North Bridge Use the North Bridge menu (BIOS Menu 16) to configure the north bridge parameters. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Chipset > Intel IGD Configuration Configure Intel IGD Settings. Memory Information...
  • Page 121 Mini-ITX SBC Primary Display [Auto] Use the Primary Display option to select the display device used by the system when it boots. Configuration options are listed below. Auto EFAULT DVMT Pre-Allocated [256M] Use the DVMT Pre-Allocated option to specify the amount of system memory that can be used by the internal graphics device.

  • Page 122: Southbridge Configuration

    Mini-ITX SBC VBIOS Default EFAULT LVDS LVDS2 5.4.2 Southbridge Configuration Use the South Bridge menu (BIOS Menu 18) to configure the Southbridge parameters. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Chipset Auto Power Button Status [Disable (ATX)]...

  • Page 123: Pci Express Configuration

    Mini-ITX SBC Audio Controller [Enabled] Use the Audio Controller BIOS option to enable or disable the High Definition Audio controller. Disabled The High Definition Audio controller is disabled. Enabled The High Definition Audio controller is enabled. EFAULT 5.4.2.1 PCI Express Configuration Use the PCI Express Configuration menu (BIOS Menu 19) to configure the PCI Express slots.

  • Page 124: S Ecurity

    Mini-ITX SBC 5.5 Security Use the Security menu (BIOS Menu 20) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Password Description Set Administrator Password If ONLY the Administrator’s password is set,...

  • Page 125: Boot

    Mini-ITX SBC 5.6 Boot Use the Boot menu (BIOS Menu 21) to configure system boot options. Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Boot Configuration Select the keyboard...
  • Page 126 Mini-ITX SBC Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Normal POST messages displayed Disabled Enabled OEM Logo displayed instead of POST messages EFAULT UEFI Boot [Disabled] Use the UEFI Boot BIOS option to allow the system to boot from the UEFI devices.

  • Page 127: Bios Menu 22: Save & Exit

    Mini-ITX SBC Aptio Setup Utility – Copyright (C) 2013 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Save Changes and Reset Reset the system after Discard Changes and Reset saving the changes. Restore Defaults Save as User Defaults...

  • Page 128: Software Drivers

    Mini-ITX SBC Chapter Software Drivers Page 114...

  • Page 129: Software Installation

    Audio Installation instructions are given below. 6.2 Software Installation All the drivers for the eKINO-BT are on the CD that came with the system. To install the drivers, please follow the steps below. Step 1: Insert the CD into a CD drive connected to the system.

  • Page 130: Figure 6-1: Driver Cd Main Menu

    Mini-ITX SBC Figure 6-1: Driver CD Main Menu Step 4: A new screen with a list of available drivers appears (Figure 6-2). Figure 6-2: Available Drivers Step 5: Install all of the necessary drivers in the menu. Page 116...

  • Page 131: Chipset Driver Installation

    Mini-ITX SBC 6.3 Chipset Driver Installation To install the chipset driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “1-Bay Trail SOC” and select the folder which corresponds to the operating system.

  • Page 132: Figure 6-4: Chipset Driver License Agreement

    Mini-ITX SBC Step 6: Click Yes to accept the agreement and continue. Figure 6-4: Chipset Driver License Agreement Step 7: The Read Me file in Figure 6-5 appears. Step 8: Click Next to continue. Figure 6-5: Chipset Driver Read Me File...

  • Page 133: Figure 6-6: Chipset Driver Setup Operations

    Mini-ITX SBC Step 9: Setup Operations are performed as shown in Figure 6-6. Step 10: Once the Setup Operations are complete, click Next to continue. Figure 6-6: Chipset Driver Setup Operations Step 11: The Finish screen in Figure 6-7 appears.

  • Page 134: Graphics Driver Installation

    Mini-ITX SBC Figure 6-7: Chipset Driver Installation Finish Screen 6.4 Graphics Driver Installation To install the Graphics driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click “1-Bay Trail SOC” and select the folder which corresponds to the operating system.

  • Page 135: Figure 6-8: Graphics Driver Welcome Screen

    Mini-ITX SBC NOTE: To install graphics driver on a 32-bit Windows 8 system, unzip 15.33.7.3366. To install graphics driver on a 64-bit Windows 8 system, unzip 15.33.7.64.336. Step 4: The Welcome Screen in Figure 6-8 appears. Step 5: Click Next to continue.

  • Page 136: Figure 6-9: Graphics Driver License Agreement

    Mini-ITX SBC Figure 6-9: Graphics Driver License Agreement Step 8: The Read Me file in Figure 6-10 appears. Click Next to continue. Figure 6-10: Graphics Driver Read Me File Step 9: Setup Operations are performed as shown in Figure 6-11.

  • Page 137: Figure 6-11: Graphics Driver Setup Operations

    Mini-ITX SBC Figure 6-11: Graphics Driver Setup Operations Step 11: The system starts installing the graphics driver. Step 12: The Finish screen in Figure 6-12 appears. Step 13: Select “Yes, I want to restart this computer now” and click Finish.

  • Page 138: Lan Driver Installation

    Mini-ITX SBC 6.5 LAN Driver Installation To install the LAN driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click 2-LAN. Step 3: Select the Realtek folder. Step 4: Select the folder which corresponds to the operating system.

  • Page 139: Figure 6-14: Lan Driver Installation

    Mini-ITX SBC Figure 6-14: LAN Driver Installation Step 10: The program begins to install. Step 11: When the driver installation is complete, the screen in Figure 6-15 appears. Step 12: Click Finish to exit. Step 0: Figure 6-15: LAN Driver Installation Complete...

  • Page 140: Audio Driver Installation

    Mini-ITX SBC 6.6 Audio Driver Installation To install the Audio driver, please do the following. Step 1: Access the driver list. (See Section 6.2) Step 2: Click 3-AUDIO. Step 3: Double click the setup file. Step 4: The InstallShield Wizard is prepared to guide the user through the rest of the process.

  • Page 141: Figure 6-17: Audio Driver Installation

    Mini-ITX SBC Figure 6-17: Audio Driver Installation Step 8: When the driver installation is complete, the screen in Figure 6-18 appears. Figure 6-18: Audio Driver Installation Complete Step 9: Select “Yes, I want to restart my computer now” and click OK.

  • Page 142: Regulatory Compliance

    Mini-ITX SBC Appendix Regulatory Compliance Page 128...
  • Page 143 Mini-ITX SBC DECLARATION OF CONFORMITY This equipment has been tested and found to comply with specifications for CE marking. If the user modifies and/or installs other devices in the equipment, the CE conformity declaration may no longer apply. FCC WARNING This equipment complies with Part 15 of the FCC Rules.

  • Page 144: Bios Options

    Mini-ITX SBC Appendix BIOS Options Page 130...
  • Page 145 Mini-ITX SBC Below is a list of BIOS configuration options in the BIOS chapter. 　 System Date [xx/xx/xx] ......................84 　 System Time [xx:xx:xx] .......................85 　 ACPI Sleep State [S3 (Suspend to RAM)]................86 　 Serial Port [Enabled]......................88 　 Change Settings [Auto] .......................88 　...
  • Page 146 Mini-ITX SBC 　 Security Device Support [Disable] .................. 103 　 USB Devices ........................104 　 Legacy USB Support [Enabled]..................104 　 Primary Display [Auto] ..................... 107 　 DVMT Pre-Allocated [256M] ..................... 107 　 DVMT Total Gfx Mem [Max]....................107 　...

  • Page 147: C Terminology

    Mini-ITX SBC Appendix Terminology Page 133...
  • Page 148 Mini-ITX SBC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface.
  • Page 149 Mini-ITX SBC Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module.
  • Page 150 Mini-ITX SBC Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer.

  • Page 151: D Digital I/O Interface

    Mini-ITX SBC Appendix Digital I/O Interface Page 137...
  • Page 152 Mini-ITX SBC D.1 Introduction The DIO connector on the eKINO-BT is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices.
  • Page 153 Mini-ITX SBC D.2 Assembly Language Sample 1 AX, 6F08H ;setting the digital port as input AL low byte = value AH – 6FH Sub-function: AL – 9 :Set the digital port as OUTPUT :Digital I/O input value D.3 Assembly Language Sample 2 AX, 6F09H ;setting the digital port as output...

  • Page 154: E Hazardous Materials Disclosure

    Mini-ITX SBC Appendix Hazardous Materials Disclosure Page 140...

  • Page 155: U Nder 2002/95/Ec W Ithout M Ercury

    Mini-ITX SBC E.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
  • Page 156 Mini-ITX SBC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Biphenyls Diphenyl (Pb) (Hg) (Cd) Chromium (CR(VI)) (PBB) Ethers (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply...
  • Page 157 Mini-ITX SBC 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元 件将会单独标示出来。 部件名称 有毒有害物质或元素 铅 汞 镉 六价铬 多溴联苯 多溴二苯 醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体 显示 印刷电路板 金属螺帽 电缆组装 风扇组装 电力供应组装 电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。 X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。...

Table of Contents