Mini-itx motherboard with 45 nm intel atom cpu ddr2 memory (up to 2 gb), vga, dvi, lvds, hdtv dual pcie gbe, compactflash, dual sata and pcie mini (190 pages)
Mini-itx sbc with 3rd generation 22nm intel mobile cpu up to 8.0 gb ddr3, dvi, hdmi, lvds, dual gbe, usb 3.0, sata 6gb/s, pcle mini, pcle x16, intel amt, rohs (208 pages)
Mini-itx sbc with 22nm intel atom or celeron soc, dual gbe, ddr3, dvi, vga, displayport, usb 3.0, rs-232, rs-422, rs-485, sata 3g/s. and rohs (133 pages)
Mini-itx sbc supports lga1155 for intel core i7/i5/i3/pentium/celeron cpu, ddr3, a vga/dvi-d, dual pcie gbe, eight usb 2.0, four sata 3gb/s, hd audio and rohs (165 pages)
KINO-PV-D5252/D4252 Mini ITX SBC MODEL: KINO-PV-D5252/D4252 Mini ITX SBC with Intel® Atom™ Processor D425/D525, DDR3 VGA, Dual LVDS, Dual GbE LAN, USB 2.0, SATA 3Gb/s, RoHS User Manual Page i Rev. 1.11 – November 6, 2015...
Page 2
KINO-PV-D5252/D4252 Mini ITX SBC Revision Date Version Changes November 6, 2015 1.11 Changed J2 to JP4 May 29, 2015 1.10 Updated for R11 version January 17, 2012 1.02 Minor update to Figure 1.4 Data flow Block Diagram Minor update to Figure 3-1: Connector and Jumper...
Page 3
KINO-PV-D5252/D4252 Mini ITX SBC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
Page 4
KINO-PV-D5252/D4252 Mini ITX SBC Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.
KINO-PV-D5252/D4252 Mini ITX SBC Table of Contents 1 INTRODUCTION......................1 1.1 I ......................2 NTRODUCTION 1.2 C ......................3 ONNECTORS 1.3 D ....................... 4 IMENSIONS 1.4 D ........................ 5 1.5 T ..................6 ECHNICAL PECIFICATIONS 2 UNPACKING ......................... 8 2.1 A ..................
Page 6
KINO-PV-D5252/D4252 Mini ITX SBC 3.2.12 LVDS1 Backlight Inverter Connector ............27 3.2.13 LVDS2 Connector ..................28 3.2.14 LVDS2 Backlight Inverter Connector ............29 3.2.15 Parallel Port Connector ................29 3.2.16 PCIe Mini Card Slot ..................31 3.2.17 SATA Drive Connectors ................. 32 3.2.18 SATA Power Connectors ................
Page 7
KINO-PV-D5252/D4252 Mini ITX SBC 4.6.8 Serial Port Setting Jumper................59 4.7 C .................... 60 HASSIS NSTALLATION 4.7.1 Airflow......................60 4.7.2 Motherboard Installation................. 60 4.8 I ............61 NTERNAL ERIPHERAL EVICE ONNECTIONS 4.8.1 AT/ATX Power Connection ................61 4.8.2 Single RS-232 Cable with Slot Bracket............62 4.9 S...
Page 8
KINO-PV-D5252/D4252 Mini ITX SBC 5.4.2 South Bridge Configuration................90 5.4.3 Intel IGD SWSCI OpRegion................91 5.5 B ........................94 5.6 S ......................... 95 ECURITY 5.7 E ......................... 96 A REGULATORY COMPLIANCE ................98 B BIOS OPTIONS ......................100 C TERMINOLOGY ..................... 103 D DIGITAL I/O INTERFACE..................
Page 9
Figure 3-21: Serial Port (COM5 and COM6) Connector Pinout Locations ......36 Figure 3-22: Serial Port (COM2) Connector Location ...............37 Figure 3-23: SMBus Connector Locations .................38 Figure 3-24: USB Connector Pinout Locations .................39 Figure 3-25: KINO-PV-D5252/D4252 External Peripheral Interface Connector ......40 Figure 3-26: Audio Connector .....................40 Page ix...
Page 13
KINO-PV-D5252/D4252 Mini ITX SBC BIOS Menus BIOS Menu 1: Main ........................68 BIOS Menu 2: Advanced ......................69 BIOS Menu 3: ACPI Settings .......................70 BIOS Menu 4: TPM Configuration ....................71 BIOS Menu 5: CPU Configuration ....................72 BIOS Menu 6: IDE Configuration....................73 BIOS Menu 7: USB Configuration ....................74 BIOS Menu 8: Super IO Configuration..................75...
KINO-PV-D5252/D4252 Mini ITX SBC 1.1 Introduction Figure 1-1: KINO-PV-D5252/D4252 The KINO-PV-D5252/D4252 Mini ITX motherboard is an Intel® Atom™ processor D525 or D425 platform. Up to two 4.0 GB 800 MHz DDR3 SDRAM SO-DIMMs are supported by the KINO-PV-D5252/D4252. The integrated Intel® ICH8M Chipset supports two GbE LAN ports through two Realtek...
KINO-PV-D5252/D4252 Mini ITX SBC 1.2 Connectors The connectors on the KINO-PV-D5252/D4252 are shown in the figure below. Figure 1-2: Connectors Page 3...
KINO-PV-D5252/D4252 Mini ITX SBC 1.3 Dimensions The dimensions of the board are listed below: Figure 1-3: KINO-PV-D5252/D4252 Dimensions (mm) Page 4...
KINO-PV-D5252/D4252 Mini ITX SBC 1.4 Data Flow F igure 1-4 shows the data flow between the two on-board chipsets and other components installed on the motherboard and described in the following sections of this chapter. Figure 1-4: Data Flow Block Diagram...
KINO-PV-D5252/D4252 Mini ITX SBC Specification KINO-PV-D5252/D4252 Two RJ-45 GbE ports by Realtek RTL8111E with ASF 2.0 support Ethernet on LAN1 Serial Ports Three RS-232 via Rear I/O Two RS-232 via four 10-pin headers One RS-232/422/485 via 14–pin header USB 2.0/1.1 Ports...
Only handle the edges of the PCB: Don't touch the surface of the motherboard. Hold the motherboard by the edges when handling. 2.2 Unpacking Precautions When the KINO-PV-D5252/D4252 is unpacked, please do the following: Follow the anti-static guidelines above. Make sure the packing box is facing upwards when opening.
If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the KINO-PV-D5252/D4252 was purchased from or contact an IEI sales representative directly by sending an email to ales@ieiworld.com.
KINO-PV-D5252/D4252 Mini ITX SBC Quick Installation Guide 2.3.1 Optional Items The following are optional components which may be separately purchased: Item and Part Number Image LPT cable (P/N: 32200-015100-RS) KB/MS PS/2 Y-cable (P/N: 32000-0023800-RS) 4-pin (2x2) to 4-pin (1x4) DC power cable with terminal block...
KINO-PV-D5252/D4252 Mini ITX SBC 3.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 KINO-PV-D5252/D4252 Layout The figures below show all the connectors and jumpers. Figure 3-1: Connector and Jumper Locations Page 13...
KINO-PV-D5252/D4252 Mini ITX SBC 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board. Connector Type Label 12 V Power connector 4-pin connector PWR2 Battery connector 2-pin wafer BAT1 CompactFlash® slot 50-pin header Digital I/O connector...
VGA port connector 15-pin connector VGACOM1 Table 3-2: Rear Panel Connectors 3.2 Internal Peripheral Connectors The section describes all of the connectors on the KINO-PV-D5252/D4252. 3.2.1 12V Power Connector CN Label: PWR2 CN Type: 4-pin Molex power connector (1x4), p=4.2mm...
KINO-PV-D5252/D4252 Mini ITX SBC Figure 3-2: 12 V Power Connector Location Description Description +12V +12V Table 3-3: 12 V Power Connector Pinouts 3.2.2 Battery Connector CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery.
KINO-PV-D5252/D4252 Mini ITX SBC Figure 3-3: Battery Connector Location Description VCC_BAT Table 3-4: Battery Connector Pinouts 3.2.3 CompactFlash® Slot CN Label: CN Type: CompactFlash® card slot CN Location: See Figure 3-4 CN Pinouts: See Table 3-5 A CompactFlash® Type I/II card can be used in this slot.
KINO-PV-D5252/D4252 Mini ITX SBC Description VCC12 FANIN1 FANOUT1 Table 3-7: CPU Fan Connector Pinouts 3.2.6 Fan Connector CN Label: 3-pin header, p=2.54 mm CN Type: CN Location: See Figure 3-7 CN Pinouts: See Table 3-8 The fan connector attaches to a cooling fan.
KINO-PV-D5252/D4252 Mini ITX SBC 3.2.8 Front Panel Connector CN Label: F_PANEL1 8-pin header, p=2.54 mm CN Type: See Figure 3-9 CN Location: CN Pinouts: See Table 3-10 The front panel connector connects to external switches and indicators to monitor and controls the motherboard.
KINO-PV-D5252/D4252 Mini ITX SBC 3.2.9 Keyboard/Mouse Connector CN Label: KB_MS1 6-pin wafer, p=2 mm CN Type: CN Location: See Figure 3-10 CN Pinouts: See Table 3-11 The keyboard/mouse connector connects to a PS/2 Y-cable that can be connected to a PS/2 keyboard and mouse.
KINO-PV-D5252/D4252 Mini ITX SBC CN Location: See Figure 3-11 CN Pinouts: See Table 3-12 The keypad connector can be used to install a numeric keypad. Figure 3-11: Keypad Connector Location Description Red LED Green LED Menu/Enter Down Auto/Exit Power Ground Table 3-12: Keypad Connector Pinouts 3.2.11 LVDS1 Connector (For Intel®...
KINO-PV-D5252/D4252 Mini ITX SBC CN Location: See Figure 3-12 CN Pinouts: See Table 3-13 The LVDS connector is for an LCD panel connected to the board. Figure 3-12: LVDS1 Connector Location Description Description LVDS_A_TX0-P LVDS_A _TX0-N LVDS_A_TX1-P LVDS_A _TX1-N LVDS_A_TX2-P...
KINO-PV-D5252/D4252 Mini ITX SBC 3.2.13 LVDS2 Connector CN Label: LVDS2 20-pin crimp, p=1.25 mm CN Type: CN Location: See Figure 3-12 CN Pinouts: See Table 3-13 The LVDS connector is for an LCD panel connected to the board. Figure 3-14: LVDS2 Connector Location...
KINO-PV-D5252/D4252 Mini ITX SBC CN Pinouts: See Table 3-17 The parallel port connector connects to a parallel port connector interface or some other parallel port device such as a printer. Figure 3-16: Parallel Port Connector Location Description Description STROBE# AUTO FORM FEED #...
KINO-PV-D5252/D4252 Mini ITX SBC 3.2.16 PCIe Mini Card Slot CN Label: PCIe Mini card slot CN Type: CN Location: F igure 3-17 CN Pinouts: See Table 3-18 The PCIe Mini card slot is for installing PCIe Mini expansion cards. Figure 3-17: PCIe Mini Card Slot Location...
KINO-PV-D5252/D4252 Mini ITX SBC Figure 3-18: SATA Drive Connector Locations Description Table 3-19: SATA Drive Connector Pinouts 3.2.18 SATA Power Connectors CN Label: SATA_PWR1 2-pin wafer, p=2.54 mm CN Type: See Figure 3-19 CN Location: CN Pinouts: See Table 3-20 The SATA Power Connector provides power output to the SATA connectors.
KINO-PV-D5252/D4252 Mini ITX SBC Figure 3-19: SATA Power Connector Locations Description Table 3-20: SATA Power Connector Pinouts CN Label: SATA_PWR2 4-pin wafer, p=2.5 mm CN Type: CN Location: See Figure 3-20 CN Pinouts: See Table 3-21 The SATA Power Connector provides power output to the SATA connectors.
KINO-PV-D5252/D4252 Mini ITX SBC Figure 3-20: SATA Power Connector Locations Description Table 3-21: SATA Power Connector Pinouts 3.2.19 Serial Port Connectors (RS-232) CN Label: COM5, COM6 CN Type: 10-pin header, p=2 mm F igure 3-21 CN Location: T able 3-22 CN Pinouts: This connector provides RS-232 communications.
KINO-PV-D5252/D4252 Mini ITX SBC Figure 3-21: Serial Port (COM5 and COM6) Connector Pinout Locations Description Description Data Carrier Direct (DCD) Data Set Ready (DSR) Receive Data (RXD) Request To Send (RTS) Transmit Data (TXD) Clear To Send (CTS) Data Terminal Ready (DTR)
DATA- Table 3-25: USB Port Connector Pinouts 3.3 External Peripheral Interface Connector Panel F igure 3-25 shows the KINO-PV-D5252/D4252 external peripheral interface connector (EPIC) panel. The KINO-PV-D5252/D4252 EPIC panel consists of the following: 4 x USB connectors 2 x Ethernet connector...
KINO-PV-D5252/D4252 Mini ITX SBC Figure 3-25: KINO-PV-D5252/D4252 External Peripheral Interface Connector 3.3.1 Audio Connector CN Label: JAUDIO1 CN Type: Line-out, Mic CN Location: F igure 3-25 The audio jacks connect to external audio devices. Line-out port (Lime): Connects to a headphone or a speaker. With multi-channel configurations, this port can also connect to front speakers.
KINO-PV-D5252/D4252 Mini ITX SBC The KINO-PV-D5252/D4252 is equipped with two built-in RJ-45 Ethernet controllers. The controllers can connect to the LAN through the RJ-45 LAN connectors. Description Description 3.3V supply LAN signal differential pair (0+) LAN signal differential pair (0-)
KINO-PV-D5252/D4252 Mini ITX SBC Description DATA0- DATA0+ DATA1- DATA1+ Table 3-28: USB Pinouts 3.3.3 Power Connector CN Label: PWR1 CN Type: 5-pin connector CN Location: F igure 3-25 CN Pinouts: T able 3-29 The connector supports the 12V power adapter.
KINO-PV-D5252/D4252 Mini ITX SBC The serial port connects to a RS-232 serial communications device. Description DATA CARRIER DETECT (DCD) DATA SET READY (DSR) RECEIVE DATA (RXD) REQUEST TO SEND (RTS) TRANSMIT DATA (TXD) CLEAR TO SEND (CTS) DATA TERMINAL READY (DTR)
KINO-PV-D5252/D4252 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the KINO-PV-D5252/D4252. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the KINO-PV-D5252/D4252 or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
KINO-PV-D5252/D4252 Mini ITX SBC 4.2 Installation Considerations NOTE: The following installation notices and installation considerations should be read and understood before the KINO-PV-D5252/D4252 is installed. installation notices pertaining installation KINO-PV-D5252/D4252 should be strictly adhered to. Failing to adhere to these precautions may lead to severe damage of the KINO-PV-D5252/D4252 and injury to the person installing the motherboard.
Chapter 3 are indeed present. If any of the unpacking list items are not available please contact KINO-PV-D5252/D4252 vendor reseller/vendor where KINO-PV-D5252/D4252 was purchased or contact an IEI sales representative. 4.4 SO-DIMM Installation SO-DIMM is a critical component of the KINO-PV-D5252/D4252. If it is not installed the KINO-PV-D5252/D4252 cannot run. Page 48...
KINO-PV-D5252/D4252 Mini ITX SBC 4.4.1 SO-DIMM Installation To install a SO-DIMM, please follow the steps below and refer to Figure 4-1. Figure 4-1: SO-DIMM Installation Step 1: Locate the SO-DIMM socket on the board (See the figure below). Place the board on an anti-static mat.
KINO-PV-D5252/D4252 Mini ITX SBC Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the notch on the memory socket. Step 3: Insert the SO-DIMM. Push the memory in at a 20º angle. (See Figure 4-1) Step 4: Seat the SO-DIMM.
OPEN a jumper means removing the plastic clip from a jumper. Before the KINO-PV-D5252/D4252 is installed in the system, the jumpers must be set in accordance with the desired configuration. The jumpers on the KINO-PV-D5252/D4252 are listed in T able 4-1.
Jumper Location: F igure 4-5 If the KINO-PV-D5252/D4252 fails to boot due to improper BIOS settings, the clear CMOS jumper clears the CMOS data and resets the system BIOS information. To do this, use the jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to pins 1 and 2.
KINO-PV-D5252/D4252 Mini ITX SBC Clear CMOS Description Short 1 - 2 Keep CMOS Setup Default Short 2 - 3 Clear CMOS Setup Table 4-3: Clear CMOS Jumper Settings The location of the clear CMOS jumper is shown in F igure 4-5 below.
KINO-PV-D5252/D4252 Mini ITX SBC Setting Description Short 1-2 and 3-4 1024 x 768 (18 bit) Short 5-6 1280 x 1024 (18 bit) Short 1-2 and 5-6 1366 x 768 (18 bit) Short 3-4 and 5-6 1280 x 800 (18 bit)
KINO-PV-D5252/D4252 Mini ITX SBC Figure 4-10: LVDS2 Voltage Select Jumper Location 4.6.8 Serial Port Setting Jumper Jumper Label: Jumper Type: 8-pin header, p=2 mm Jumper Settings: See Table 4-9 Jumper Location: See Figure 4-11 Used for RS-232/422/485 communications. Description Short 1-2...
The KINO-PV-D5252/D4252 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface. In a system with an individual power supply unit, the cooling fan of a power supply can also help generate airflow through the board surface.
4.8 Internal Peripheral Device Connections This section outlines the installation of peripheral devices to the onboard connectors 4.8.1 AT/ATX Power Connection Follow the instructions below to connect the KINO-PV-D5252/D4252 to an AT or ATX power supply. WARNING: Disconnect the power supply power cord from its AC power source to prevent a sudden power surge to the KINO-PV-D5252/D4252.
KINO-PV-D5252/D4252 Mini ITX SBC Step 3: Connect Power Cable to Power Supply. Connect one of the 4-pin (1x4) Molex type power cable connectors to an AT/ATX power supply. See Figure 4-13. Figure 4-13: Connect Power Cable to Power Supply 4.8.2 Single RS-232 Cable with Slot Bracket...
0: 4.9 Software Installation All the drivers for the KINO-PV-D5252/D4252 are on the CD that came with the system. To install the drivers, please follow the steps below. Step 1: Insert the CD into a CD drive connected to the system.
KINO-PV-D5252/D4252 Mini ITX SBC Figure 4-15: Introduction Screen Step 3: Click KINO-PV-D5252/D4252. Step 4: A new screen with a list of available drivers appears (Figure 4-16). Figure 4-16: Available Drivers Step 5: Install all of the necessary drivers in this menu.
KINO-PV-D5252/D4252 Mini ITX SBC 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.
KINO-PV-D5252/D4252 Mini ITX SBC Function Page up Move to the next page Page down Move to the previous page Main Menu – Quit and do not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu --...
KINO-PV-D5252/D4252 Mini ITX SBC 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
KINO-PV-D5252/D4252 Mini ITX SBC System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds. 5.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices...
KINO-PV-D5252/D4252 Mini ITX SBC 5.3.1 ACPI Settings The ACPI Settings menu (BIOS Menu 3) configures the Advanced Configuration and Power Interface (ACPI) options. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced ACPI Sleep State [S1 (CPU Stop Clock)] : Select Screen ↑...
KINO-PV-D5252/D4252 Mini ITX SBC 5.3.2 Trusted Computing Use the Trusted Computing menu (BIOS Menu 4) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM). Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced...
KINO-PV-D5252/D4252 Mini ITX SBC 5.3.3 CPU Configuration Use the CPU Configuration menu (BIOS Menu 5) to view detailed CPU specifications and configure the CPU. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced CPU Configuration Processor Type Intel(R) Atom(TM) CPU CPU D425 @ 1.80GHz...
KINO-PV-D5252/D4252 Mini ITX SBC 5.3.4 IDE Configuration Use the IDE Configuration menu (BIOS Menu 6) to change and/or set the configuration of the ATA/IDE devices installed in the system. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced...
KINO-PV-D5252/D4252 Mini ITX SBC Configure SATA as [IDE] Use the Configure SATA as option to configure SATA devices as normal IDE devices. Configures SATA devices as normal IDE device. EFAULT AHCI Configures SATA devices as AHCI device. 5.3.5 USB Configuration Use the USB Configuration menu (BIOS Menu 7) to read USB configuration information and configure the USB settings.
KINO-PV-D5252/D4252 Mini ITX SBC Enabled Legacy USB support enabled EFAULT Legacy USB support disabled Disabled Auto Legacy USB support disabled if no USB devices are connected 5.3.6 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 8) to set or change the configurations for the FDD controllers, parallel ports and serial ports.
KINO-PV-D5252/D4252 Mini ITX SBC 5.3.6.1 Serial Port 0 Configuration Use the Serial Port 0 Configuration menu (BIOS Menu 9) to configure the serial port 0. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced Serial Port 0 Configuration...
Page 90
KINO-PV-D5252/D4252 Mini ITX SBC IO=2F8h; Serial Port I/O port address is 2F8h and the interrupt IRQ=3, 4 address is IRQ3 and IRQ4 5.3.6.1.1 Serial Port 1 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.
Page 91
KINO-PV-D5252/D4252 Mini ITX SBC 5.3.6.1.2 Serial Port 2 Configuration Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port. Disabled Disable the serial port Enable the serial port Enabled EFAULT Change Settings [Auto] Use the Change Settings option to change the serial port IO port address and interrupt address.
KINO-PV-D5252/D4252 Mini ITX SBC Auto The serial port IO port address and interrupt address EFAULT are automatically detected. Serial Port I/O port address is 2E8h and the interrupt IO=2E8h; address is IRQ10 IRQ=10 IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt...
Page 93
KINO-PV-D5252/D4252 Mini ITX SBC Change Settings [Auto] Use the Change Settings option to change the parallel port IO port address and interrupt address. Auto The parallel port IO port address and interrupt EFAULT address are automatically detected. Parallel Port I/O port address is 378h and the IO=378h;...
KINO-PV-D5252/D4252 Mini ITX SBC 5.3.7 H/W Monitor The H/W Monitor menu (BIOS Menu 11) shows the operating temperature, fan speeds and system voltages. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced PC Health Status CPU Temperature :+39 C...
Page 95
KINO-PV-D5252/D4252 Mini ITX SBC Voltages: VCC3V V_core Vcc12 Vcc1_5VDDR VSB3V VBAT CPU Smart Fan control [Auto Mode] Use the CPU Smart Fan control option to configure the CPU fan. Auto Mode The fan adjusts its speed using these settings: Temperature Bound 1...
KINO-PV-D5252/D4252 Mini ITX SBC 5.3.8 Secondary Super IO Configuration The Secondary Super IO Configuration (BIOS Menu 13) displays IO chip type and the submenus for configuring the external SATA ports 5 and 6. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
KINO-PV-D5252/D4252 Mini ITX SBC IO=2C0h; Serial Port I/O port address is 2C0h and the interrupt IRQ=11 address is IRQ11 Serial Port I/O port address is 2C0h and the interrupt IO=2C0h; address is IRQ10, 11 IRQ=10, 11 IO=2C8h; Serial Port I/O port address is 2C8h and the interrupt...
KINO-PV-D5252/D4252 Mini ITX SBC IO=2C8h; Serial Port I/O port address is 2C8h and the interrupt IRQ=10, 11 address is IRQ10, 11 Serial Port I/O port address is 2D0h and the interrupt IO=2D0h; address is IRQ10, 11 IRQ=10, 11 IO=2D8h; Serial Port I/O port address is 2D8h and the interrupt...
KINO-PV-D5252/D4252 Mini ITX SBC Console Redirection [Disabled] Use Console Redirection option to enable or disable the console redirection function. Disabled the console redirection function Disabled EFAULT Enabled Enabled the console redirection function 5.4 Chipset Use the Chipset menu (BIOS Menu 14) to access the Northbridge and Southbridge...
KINO-PV-D5252/D4252 Mini ITX SBC 5.4.1 Host Bridge Configuration Use the Host Bridge Configuration menu (BIOS Menu 15) to configure the Northbridge chipset. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Chipset > Memory Frequency and Timing > OnChip VGA Configuration...
KINO-PV-D5252/D4252 Mini ITX SBC Enables ION graphics controller. EFAULT Enables PCI/PEG graphics controller. PCI/PEG 5.4.1.1 Memory Frequency and Timing Use the Memory Frequency and Timing submenu (BIOS Menu 16) to configure memory frequency and timing settings. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
KINO-PV-D5252/D4252 Mini ITX SBC Enabled Enables DRAM Timing. EFAULT Disables DRAM Timing. Disabled 5.4.1.2 OnChip VGA Configuration Use the OnChip VGA Configuration submenu (BIOS Menu 16) to configure the OnChip VGA. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
KINO-PV-D5252/D4252 Mini ITX SBC Multi-Monitor Support [Enabled] Use Multi-Monitor Support option to enable or disable the multi-monitor function. Disabled the multi-monitor function Disabled Enabled Enabled the multi-monitor function EFAULT 5.4.2 South Bridge Configuration Use the South Bridge Configuration menu (BIOS Menu 18) to configure the Southbridge chipset.
KINO-PV-D5252/D4252 Mini ITX SBC HD Audio Controller [Enabled] Use the HD Audio Controller option to enable or disable the High Definition Audio controller. Enabled onboard High Definition Audio controller EFAULT automatically detected and enabled The onboard High Definition Audio controller is disabled...
KINO-PV-D5252/D4252 Mini ITX SBC Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Advanced Chipset Intel IGD SWSCI OpRegion Configuration Select DVMT Mode/Fixed Mode DVMT Mode Select [DVMT Mode] DVMT/FIXED Memory [Maximum] IGD - Boot Type [VBIOS Default] ---------------------...
Page 106
KINO-PV-D5252/D4252 Mini ITX SBC VBIOS Default EFAULT CRT + LFP LCD Panel Type [VBIOS Default] Use the LCD Panel Type option to select the type of flat panel connected to the system. Configuration options are listed below. Select by Panel ID D...
KINO-PV-D5252/D4252 Mini ITX SBC 5.5 Boot Use the Boot menu (BIOS Menu 20) to configure system boot options. Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Boot Configuration Boot NumLock State...
KINO-PV-D5252/D4252 Mini ITX SBC Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Normal POST messages displayed Disabled Enabled OEM Logo displayed instead of POST messages EFAULT Launch PXE OpROM [Disabled] Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices.
KINO-PV-D5252/D4252 Mini ITX SBC User Password Use the User Password option to set or change a user password. 5.7 Exit Use the Exit menu (BIOS Menu 22) to load default BIOS values, optimal failsafe values and to save configuration changes.
Page 110
KINO-PV-D5252/D4252 Mini ITX SBC Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults. Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options.
KINO-PV-D5252/D4252 Mini ITX SBC Appendix Regulatory Compliance Page 98...
Page 112
KINO-PV-D5252/D4252 Mini ITX SBC DECLARATION OF CONFORMITY This equipment has been tested and found to comply with specifications for CE marking. If the user modifies and/or installs other devices in the equipment, the CE conformity declaration may no longer apply.
KINO-PV-D5252/D4252 Mini ITX SBC Appendix BIOS Options Page 100...
Page 114
KINO-PV-D5252/D4252 Mini ITX SBC Below is a list of BIOS configuration options in the BIOS chapter. BIOS Information .........................68 System Date [xx/xx/xx] ......................68 System Time [xx:xx:xx] .......................69 ACPI Sleep State [S1 (CPU Stop Clock)] ................70 ...
Page 115
KINO-PV-D5252/D4252 Mini ITX SBC Share Memory Size [8 MB] ....................89 Multi-Monitor Support [Enabled] ..................90 Restore AC Power Loss [Last State] .................90 HD Audio Controller [Enabled] ...................91 USB Function [Enabled]......................91 USB 2.0 (EHCI) Support [Enabled] ..................91 ...
KINO-PV-D5252/D4252 Mini ITX SBC Appendix Terminology Page 103...
Page 117
KINO-PV-D5252/D4252 Mini ITX SBC AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface.
Page 118
KINO-PV-D5252/D4252 Mini ITX SBC Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly with the system memory. DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module.
Page 119
KINO-PV-D5252/D4252 Mini ITX SBC Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liquid crystal panel in between. LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer.
KINO-PV-D5252/D4252 Mini ITX SBC D.1 Introduction The DIO connector on the KINO-PV-D5252/D4252 is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 4-bit digital inputs and 4-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices.
KINO-PV-D5252/D4252 Mini ITX SBC D.2 Assembly Language Sample 1 AX, 6F08H ;setting the digital port as input AL low byte = value AH – 6FH Sub-function: AL – 9 :Set the digital port as OUTPUT :Digital I/O input value D.3 Assembly Language Sample 2 AX, 6F09H ;setting the digital port as output...
KINO-PV-D5252/D4252 Mini ITX SBC Appendix Watchdog Timer Page 110...
Page 124
KINO-PV-D5252/D4252 Mini ITX SBC NOTE: The following discussion applies to DOS. Contact IEI support or visit the IEI website for drivers for other operating systems. The Watchdog Timer is a hardware-based timer that attempts to restart the system when it stops working.
Page 125
KINO-PV-D5252/D4252 Mini ITX SBC NOTE: The Watchdog Timer is activated through software. The software application that activates the Watchdog Timer must also deactivate it when closed. If the Watchdog Timer is not deactivated, the system will automatically restart after the Timer has finished its countdown.
KINO-PV-D5252/D4252 Mini ITX SBC F.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
Page 128
KINO-PV-D5252/D4252 Mini ITX SBC Part Name Toxic or Hazardous Substances and Elements Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Biphenyls Diphenyl (Pb) (Hg) (Cd) Chromium (CR(VI)) (PBB) Ethers (PBDE) Housing Display Printed Circuit Board Metal Fasteners Cable Assembly Fan Assembly Power Supply...