Audio Setup - Clarion M606 Owner's Manual & Installation Manual

System Setup
DISCON (BT mode)
Disconnect currently connected mobile phone.
1. Press the [ENT] button, mobile phone dis-
plays are currently connected.
2. Press the [ENT] button to disconnect.
PIN CODE
1. Press the [ENT] button.
2. Rotate the [UP/DOWN] knob and press
[ ] or [ ] button to choose a 4-digit
password.
3. Press the [ENT] button.to confirm.
The PIN CODE default setting is " 0000 ".
SCREEN SAVE: ON/OFF
Rotate the [UP/DOWN] knob to choose screen
saver ON or OFF.
ON: The screen saver will appear on the LCD
screen after 30 seconds of non-use.
SCROLL: ON/OFF
For track information that is longer than the
display panel:
When SCOLL is ON, the LCD will scroll the
ID3 TAG information across the display, e.g.:
TRACK->FOLDER->FILE->ALBUM->TITLE-
>ARTIST->TRACK->...
When SCROLL is OFF, the LCD will display
one of the ID3 TAG information, the default
is TRACK, but user can adjust it to other ID3
TAG information by pressing [DISP] button.
PANDORA: ON/OFF
Select OFF if the Pandora application has not
been installed on your iPod touch or iPhone.
DIMMER: ON/OFF
Rotate the [UP/DOWN] knob to choose
DIMMER ON or OFF.
• ON: LCD dimmer is active when small
light of boat is turned ON.
• OFF: LCD always maximum brightness
regardless of the boat small light.
BEEP: ON/OFF
Rotate the [UP/DOWN] knob to choose
button beep sound ON or OFF.
12/24H
Rotate the [UP/DOWN] knob to choose time
format: 12 HOURS or 24 HOURS.
REGION
Rotate the [UP/DOWN] knob to choose a
Radio Region from N.America/Europe/Asia/
Australia.
FACTORY RST
1. Rotate the [UP/DOWN] knob to choose
YES or NO.
2. YES: Press the [ENT] button to show
"CONFIRM".
3. Rotate the [UP/DOWN] knob to choose
YES or NO.
4. YES: Pressing the [ENT] button will reset
the unit.

Audio Setup

STANDARD
1. Press the [ ] button to enter sound effect
setting mode. First press shows current
BEAT EQ setting. Rotate the [VOLUME]
knob to change BEAT EQ in this order:
EQ OFF ->POP -> CLASSIC -> JAZZ ->
CUSTOM.
On CUSTOM setting mode, press the [ENT]
button. Then rotate the [UP/DOWN] knob
to select BAS, MID, or TRE Gain, rotate the
[VOLUME] knob to select a value:(-6)- (+6),
press [ENT] button to confirm.
2. After pressing the [ ] button, press [ ]
or [ ] button to select USER preset
including:
LOUDNESS -> BALANCE -> FADER ->
HPF (high pass filter) -> LPF (low pass
filter) -> THROUGH(HPF/LPF), rotate the
[VOLUME] knob to select a value.
3. After pressing the [ ] button, rotate the
[UP/DOWN] knob to show NON FADE, and
press [ENT] button to enter. Rotate the [UP/
DOWN] knob to select LPF, PHASE or SUB
VOL, rotate the [VOLUME] knob to select
the value.
MULTI ZONE
1. Press the [ ] button to enter sound effect
setting mode.
2. Rotate the [VOLUME] knob to select the
value of BALANCE (LEFT 1-7 -> CENTER
-> RIGHT 1-7). Rotate the [UP/DOWN]
knob to select ZONE 1, 2, 3 or 4.
3. After selecting a ZONE number, rotate the
[VOLUME] knob to change BEAT EQ.
On CUSTOM setting mode, press the [ENT]
button. Then rotate the [UP/DOWN] knob
to select BAS, MID, or TRE Gain, rotate the
[VOLUME] knob to select a value:(-6)- (+6),
press [ENT] button to confirm.
4. After selecting a ZONE number, press
[ ] or [ ] button to select THOUGH,
HPF or LPF. Rotate the [VOLUME] knob to
select a value.
9
M606