System Setup; Audio Setup - Clarion CMD8 Owner's Manual & Installation Manual

System Setup

To change adjustment setting
1. Press the [ADJUST] button to switch to
the adjustment selection display.
2. Press the [ ] button to select the
] or [
"item name".
CLOCK, DX/LO, SCRN SVR, SCROLL,
R E A R / S - W , S W P H A S E , P a n d o r a ,
DIMMER, CONTRAST, BEEP, 12/24H,
RESET
3. Rotate the [UP/DOWN] knob to select the
"desired setting value".
* In the case of display blinking "ENT", you
can press the [ENTER] button to adjust
the setting value.
4. After completing settings, press the
[ADJUST] or [RETURN] button to return to
the previous mode.
CLOCK
1. Press the [ENTER] button.
2. Press the [ ] button to select the
] or [
hour or the minute.
3. Rotate the [UP/DOWN] knob to set the
correct time.
* The clock is displayed in 12-hour format
by default.
4. Press the [ENTER] button to store the time
into memory.
Note:
• Y ou cannot set the clock when it is
displayed with only the ignition on. If you
drain or remove the boat's battery or take
out this unit, the clock is reset. While
setting the clock, if another button or
operation is selected, the clock set mode
is canceled.
DX/LO (RADIO mode)
Rotate the [UP/DOWN] knob to choose radio
local or distant at RADIO mode.
• LO: Only stations with strong signal can
be received.
• DX: Stations with strong and weak signals
can be received.
8 CMD8
SCRN SVR: ON/OFF
Rotate the [UP/DOWN] knob to choose
SCRN SVR (screen saver) ON or OFF.
SCROLL: ON/OFF
For track information that is longer than the
display panel:
When SCOLL is ON, the LCD will scroll the
ID3 TAG information across the display, e.g.:
TRACK->FOLDER->FILE->ALBUM->TITLE-
>ARTIST->TRACK->...
When SCROLL is OFF, the LCD will display
one of the ID3 TAG information, the default
is TRACK, but user can adjust it to other
ID3 TAG information by pressing [DISPLAY]
button.
REAR/S-W
Rotate the [UP/DOWN] knob to choose
REAR or S-WOOFER (SUB-WOOFER).
SW PHASE
Rotate the [UP/DOWN] knob to choose
S U B W O O F E R p h a s e R E V E R S E o r
NORMAL.
Pandora: ON/OFF
Select OFF if the Pandora application has
not been installed on your iPod touch or
iPhone.
DIMMER: ON/OFF
Rotate the [UP/DOWN] knob to choose
DIMMER ON or OFF.
• ON: LCD dimmer is active when small
light of vehicle is turned ON.
• OFF: LCD always maximum brightness
regardless of the vehicle small light.
CONTRAST
You can adjust the display contrast to match
the angle of installation of the unit.
* The factory default setting is "9".
(Adjustment level: 1 to 10)
Rotate the [UP/DOWN] knob to adjust the
contrast.
System Setup
BEEP: ON/OFF
Rotate the [UP/DOWN] knob to choose button
beep sound ON or OFF.
12/24H
Rotate the [UP/DOWN] knob to choose time
format: 12 HOURS or 24 HOURS.

Audio Setup

Press the [AUDIO] button to enter sound effect
setting mode. First press shows current BEAT
EQ setting. Rotate the [UP/DOWN] knob to
changes BEAT EQ in this order:
OFF -> B-BOOST -> IMPACT -> EXCITE ->
CUSTOM
Rotate the [UP/DOWN] knob to changes
CUSTOM, and press the [ENTER] button, the
press [ ] button to select it including:
] or [
BASS-G -> BASS-F -> BASS-Q -> MID-G ->
MID-F -> MID-Q -> TREBLE-G -> TREBLE-F
-> TREBLE-Q, rotate the [UP/DOWN] knob to
select a value.
BASS-G / MID-G / TREBLE-G: (-7)- (+7)
BASS-F: 50 / 100 / 200
BASS-Q: 0.7 / 1.0 / 1.4 / 2.0
MID-F: 500 /1K / 2K
MID-Q: 0.7 / 1.0 / 1.4 / 2.0
TREBLE-F: 5k / 10k / 15k
TREBLE-Q: 0.7 / 1.0 / 1.4 / 2.0
RESET
Long press [ ENTER ] button. Settings will
be set to the default value.
Press the [AUDIO] button, then press [
] or
] button to select USER preset including:
[
BALANCE -> FADER -> M-B EX -> HPF
(high pass filter) -> LPF (low pass filter) ->
SUBW VOL (Subwoofer Volume), rotate the
[UP/DOWN] knob to select a value.
BALANCE: LEFT 1-7 -> CENTER -> RIGHT
1-7
FADER: FRONT 1-7 -> CENTER -> REAR
1-7
M-BEX: ON / OFF
HPF: THROUGH / 60 / 90 / 120
LPF: THROUGH / 60 / 90 / 120
SUBW VOL: (-6) - (+6)