Error Displays; Specifications - Clarion M606 Owner's Manual & Installation Manual

Bluetooth
Problem Cause
The device does not support the
Cannot pair the
profiles required for the system.
Bluetooth enabled
device with the boat
The Bluetooth function of the
audio system.
device is not enabled.
The audio quality is
poor after connection The internal microphone gain is
with a Bluetooth- not set correctly.
enabled device.

7. ERROR DISPLAYS

If an error occurs, one of the following errors is displayed.
Take the measures described below to solve the problem.
Display Cause
ERROR 2 Do not support iPod, iPhone & iPad.
If an error display other than the ones described above appears, press the [RESET] button. If
the problem persists, turn off the power and consult your store of purchase.
* When the [RESET] button is pressed, frequencies of radio stations, titles, etc. are stored in
memory are cleared.
16
M606
Measure
Use another device to connect.
Refer to the user manual of the device for how to
enable the function.
Adjust the gain of the internal microphone in
System Setup.
Measure
Change another device.
* The head unit will return to RADIO mode.

8. SPECIFICATIONS

FM Tuner
Frequency Range:
North America: 87.9-107.9MHz
Europe: 87.5-108MHz
Asia & Australia: 87.5-108MHz
Usable Sensitivity: 8 dBμV
Alternate Channel Selectivity: 60 dB
Stereo Separation (1 kHz): 30 dB
Frequency Response (±3 dB):
30 Hz to 15 kHz
AM Tuner
Frequency Range:
North America: 530 kHz to 1710 kHz
Europe: 531 kHz to 1602 kHz
Asia & Australia: 531 kHz to 1629 kHz
Usable Sensitivity: 28 dBμV
WB Tuner
Frequency Range: 162.400 to 162.550 MHz
Step length: 25 kHz
MP3/WMA mode
MP3 sampling rate: 8 kHz to 48 kHz
MP3 bit rate: 8 kbps to 320 kbps / VBR
WMA bit rate: 8 kbps to 320 kbps
Logical format: ISO9660 level 1,2
Joliet file system
USB
Specification: USB 1.1
Playable audio format:
MP3(.mp3): MPEG 1/2/Audio Layer-3
WMA(.wma): Ver 7/8/9.1/9.2
Bluetooth
Specification: Bluetooth Ver. 2.1+EDR
Profile:
A2DP (Advanced Audio Distribution Profile)
AVRCP (AV Remote Control Profile)
Send/Receive Sensitivity: Class 2
Audio Amplifier
Maximum Power Output: 180 W (45 W × 4 ch)
Bass Control Action (100 Hz): +6 dB, –6 dB
Treble Control Action (10 kHz): +6 dB, –6 dB
Line Output Level (USB 1 kHz): 4 V
Input
Audio input sensitivity:
High: 320mV (at 1V output)
Mid: 650mV (at 1V output)
Low: 1.3V (at 1V output)
(input impedance 10 k or greater)
Aux-in level: ≤2V
General
Power supply voltage:
14.4VDC (10.8 to 15.6V allowable),
negative ground
Pre-Amp output voltage:
4.0V (USB play mode: 1kHz, 0dB, 10k load)
Fuse: 15A
Dimensions of the Main Unit:
196mm Width × 88.8mm Height × 235.6mm Depth
7-23/32(width) × 3-16/32(Height) ×
9-9/32(Depth)
Weight of the Main Unit: 1.94 lb. (0.88 kg)
Dimensions of the Remote Control unit:
43mm Width × 11mm Height × 113mm Depth
1-2/3(Width) × 2/5(Height) × 4-2/5(Depth)
Weight of the Remote Control Unit:
1.16oz. (36g) (including battery)
Note:
• Specifications and design are subject to
change without notice for further improvement.
Power Output:
18W RMS x 4 Channels at 4
and 1% THD+N
Signal to Noise Ratio:
94dBA (reference: 1W into 4 )