Troubleshooting; Error Displays - Clarion M335 Service Manual

AREA CHANGE
Use this function when you are using the boat stereo anywhere outside the U.S.
Switchable frequency spacing Switchable frequency spacing
Switchable frequency spacing Switchable frequency spacing Switchable frequency spacing
This boat stereo is initially set to tune in frequency intervals of 10 kHz for AM and 200 kHz for FM, the standard
calibrations in the U.S. When using the unit outside the U.S., use the following procedure to switch the frequency
range. The table below lists the frequency specifications for the U.S. and other countries.
Frequecy spacing
A M A M A M A M A M
Frequecy range
Frequecy spacing
F M F M F M F M F M
Frequecy range
Switch the area change Switch the area change Switch the area change Switch the area change Switch the area change
Australia standard (New Setting) Australia standard (New Setting)
Australia standard (New Setting) Australia standard (New Setting) Australia standard (New Setting)
While pressing the [A-M] [A-M] [A-M] [A-M] button, press the [RPT} [A-M]
Inside U.S. standard (Initial Setting) Inside U.S. standard (Initial Setting)
Inside U.S. standard (Initial Setting) Inside U.S. standard (Initial Setting) Inside U.S. standard (Initial Setting)
While pressing the [A-M] [A-M] button, press the [SCN} [A-M] [A-M] [A-M]
Europe standard (New Setting) Europe standard (New Setting)
Europe standard (New Setting) Europe standard (New Setting) Europe standard (New Setting)
While pressing the [A-M] [A-M] [A-M] [A-M] [A-M] button, press the [RDM}

TROUBLESHOOTING

Problem Problem Problem
Problem Problem
Power does not turn on (or no
sound is produced).
Compact disc cannot be
loaded.
Sound skips or is noisy.
Sound is bad directly after
power is turned on.

ERROR DISPLAYS

To protect the system, this unit has been equipped with self diagnostic functions. If a fault arises, a warning is
issued by various error displays. Follow the corrective measures and remove the fault.
Error Display
ER2
ER3
ER6
Initial Setting Initial Setting Initial Setting Initial Setting Initial Setting
(U.S. standards)
10 kHz
530 to 1,710 kHz
200 kHz
87.9 to 107.9 kHz
[RPT} [RPT} [RPT} buton, then "Australia standard" will be selected. [RPT}
[SCN} [SCN} [SCN} buton, then "U.S. standard" will be selected. [SCN}
[RDM} [RDM} [RDM} [RDM} buton, then "Europe standard" will be selected.
Cause Cause Cause
Cause Cause
Fuse is blown.
Another compact disc is already
loaded.
Compact disc is dirty.
Compact disc is heavily scratched
or warped.
Water droplets may form on the
internal lens when the car is
parked in a humid place.
This error display indicates that a fault has arisen in the mechanism of the
source unit (for example, the disc cannot be ejected).
-Check the source unit
This error display indicates that the pickup focus is off because of a scratched
disc or some other factor during source unit play.
-Check the compact unit
This indicates that the CD's TOC (table of contents) cannot be read, because
the selected disc is upside-down.
- 3 - - 3 - - 3 - - 3 - - 3 -
New Setting New Setting New Setting
New Setting New Setting
(Australia standard)
9 kHz
531 to 1,602 kHz
50 kHz
87.0 to 108 kHz
Replace with a fuse of the same amperage as the
old fuse.
Eject the compact disc before loading the new
one.
Clean the compact disc with a soft cloth.
Replace with a compact disc with no scratches.
Let dry for about 1 hour with the power on.
Corrective Measure
New Setting New Setting New Setting
New Setting New Setting
(Europe standards)
9 kHz
531 to 1,602 kHz
50 kHz
87.5 to 108 kHz
Measure Measure Measure
Measure Measure
M335/M235 M335/M235 M335/M235 M335/M235 M335/M235