Related Manuals for SHOWTEC Pixel Bar 12 Q6
Summary of Contents for SHOWTEC Pixel Bar 12 Q6
- Page 1 MANUAL ENGLISH Pixel Bar 12 Q6 Ordercode: 41303 Highlite International B.V. – Vestastraat 2 – 6468 EX – Kerkrade – the Netherlands...
-
Page 2: Table Of Contents
Pixel Bar 12 Q6 Table of contents Warning ....................................2 Safety Instructions ................................. 2 Operating Determinations ............................4 Rigging .................................... 4 Connection with the mains ............................5 Return Procedure ................................5 Claims ....................................5 Description of the device ..............................6 Overview .................................. -
Page 3: Warning
Save the carton and all packing materials. In the event that the fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing. Your shipment includes: Showtec Pixel Bar 12 Q6 • 3 brackets and screws • IEC powercable 1,5m •... - Page 4 For replacement, use fuses of same type and rating only. The user is responsible for correct positioning and operating of the Pixel Bar 12 Q6. The manufacturer will not accept liability for damages caused by the misuse or incorrect installation of this device.
-
Page 5: Operating Determinations
When rigging, derigging or servicing the Pixel Bar 12 Q6, always make sure, that the area below the installation place is blocked and staying in the area is forbidden. The Pixel Bar 12 Q6 can be placed on a flat stage floor or mounted to any kind of truss by a clamp. Ordercode: 41303... -
Page 6: Connection With The Mains
Pixel Bar 12 Q6 Connection with the mains Connect the device to the mains with the power plug. Always check if the right color cable is connected to the right place. International EU Cable UK Cable US Cable BROWN YELLOW/COPPER... -
Page 7: Description Of The Device
Features The Showtec Pixel Bar 12 Q6 is a LED bar with 12 x 6-in-1 RGBWA-UV LEDs. It offers full pixel control in 72 channel mode to create beautiful color flows but can also be controlled in 3, 8, 11 or 13 channel mode. -
Page 8: Backside
DMX signal connector (OUT) 3-pin Installation Remove all packing materials from the Pixel Bar 12 Q6. Check that all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. -
Page 9: One Pixel Bar (Sound-Control)
Pixel Bar 12 Q6 One Pixel Bar (Sound-control) 01) Fasten the effect light onto firm trussing or place it on the floor. Leave at least 0,5 meter on all sides for air circulation. 02) When the Pixel Bar is not connected by a DMX-cable, it functions as a stand-alone device. -
Page 10: Multiple Pixel Bars (Dmx512 Mode)
Pixel Bar 12 Q6 Multiple Pixel Bars (DMX512 Mode) 01) Fasten the effect light onto firm trussing or place it on the floor. Leave at least 0,5 meter on all sides for air circulation. 02) Plug the end of the electric mains power cord into a proper electric power supply socket. -
Page 11: Fixture Linking
The Pixel Bar 12 Q6 uses up to 72 channels. Important: Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485 standard no more than 30 devices should be connected on one data link. -
Page 12: Control Panel
Pixel Bar 12 Q6 Control Panel A. LCD Display B. Mode button C. Setup Button D. Up Button E. Down Button Fig. 05 DMX Control Mode The fixtures are individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address the next time.) -
Page 13: Menu Overview
Pixel Bar 12 Q6 Menu overview Ordercode: 41303... -
Page 14: Main Menu Options
Pixel Bar 12 Q6 Main Menu Options DMX Address / DMX Configuration Slave mode Static color control Sound control mode Built-in programs Auto run mode DMX Mode With this menu you can set the DMX address and choose a DMX configuration. -
Page 15: Static Color Mode
Pixel Bar 12 Q6 Static Color Mode With this menu you can create a static color. 01) Press the Mode button until the display shows 02) Press the Setup button to make a color. 03) With this sub menu you can set 6 static colors of the Pixel Bar. -
Page 16: Built-In Programs
Pixel Bar 12 Q6 Built-in Programs With this menu you can choose a built-in program. 01) Press the Mode button on the device until the display shows 02) You can choose between 19 built-in programs , by using the Up and Down buttons. -
Page 17: Reset Factory Settings
Switch the power off and hold at the same time the Mode and Up button. Switch the power on and release the Mode and Up button. The Pixel Bar 12 Q6 will reset to the factory settings. The fixture will start up in the Auto Run mode. DMX Channels 3 DMX Channels Channel 1 –... -
Page 18: Dmx Channels
Pixel Bar 12 Q6 8 DMX Channels Channel 1 – Red Dimmer intensity (CH7 must be set between 0-255 0-255 Gradual adjustment Red from 0 – 100% Channel 2 – Green Dimmer intensity (CH7 must be set between 0-255 0-255 Gradual adjustment Green from 0 –... - Page 19 Pixel Bar 12 Q6 Channel 8 – Built-in Programs (CH1 must be set between 001-255 No function 2-11 Program 1 12-23 Program 2 24-35 Program 3 36-47 Program 4 48-59 Program 5 60-71 Program 6 72-83 Program 7 84-95 Program 8...
-
Page 20: 13 Dmx Channels
Pixel Bar 12 Q6 Channel 10 – Sound mode (CH1 and CH8 must be set between 228-255 0-84 Sound mode 1 85-169 Sound mode 2 170-255 Sound mode 3 Channel 11 – Fade (CH1 And CH2,CH3, CH4, CH5, CH6 or CH7 must be set between 001-255, CH8 between 12-227 or CH9... - Page 21 Pixel Bar 12 Q6 Channel 9 – Linear Strobe (CH1 and CH2, CH3, CH4, CH5, CH6, CH7 or CH10 must be set between 0-255 and CH8 between 12-255 0-255 Strobe intensity, from slow to fast (0-20 Hz) Channel 10 –Dimmer intensity Sections...
-
Page 22: 72 Dmx Channels
Pixel Bar 12 Q6 72 DMX Channels Channel 1 – Red Pixel LED 1 0-255 Gradual adjustment Red from 0 – 100% Channel 2 – Green Pixel LED 1 0-255 Gradual adjustment Green from 0 – 100% Channel 3 – Blue Pixel LED 1 0-255 Gradual adjustment Blue from 0 –... -
Page 23: Maintenance
04) The electric power supply cables must not show any damages or material fatigue. The Pixel Bar 12 Q6 requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply and then wipe the cover with a damp cloth. -
Page 24: Troubleshooting
Q6, as this may damage the unit and the warranty will become void. 06) Return the device to your Showtec dealer. No Response to DMX Response: Suspect the DMX cable or connectors, a controller malfunction, a light effect DMX card malfunction. - Page 25 Pixel Bar 12 Q6 Problem Probable cause(s) Solution No power to the fixture • Check if power is switched on and One or more cables are plugged in. fixtures do not function at all Primary fuse blown • Replace fuse Fixtures reset The controller is not connected.
-
Page 26: Product Specifications
Pixel Bar 12 Q6 Product Specifications Model: Showtec Pixel Bar 12 Q6 Input Voltage: 100-240V AC, 50/60Hz Consumption Power 72 Watt Power linking 110V: 7pcs Power linking 240V: 14pcs DMX linking: 30pcs Fuse: 3A / 250V Dimensions: 1085 x 80 x 135 mm (LxWxH) (incl. brackets) -
Page 27: Dimensions
Pixel Bar 12 Q6 Dimensions Ordercode: 41303... - Page 28 ©2016 Showtec...