Table of Contents
Advertisement
ASSEMBLY
ASSEMBLY (FIGURE 1)
Preparation
1. Remove the following from the bottom of the bed:
A
A. Four locking (4) casters in a plastic bag.
S
B. Pendant in a plastic bag.
S
E
C. Banding that secures the power cord, pendant cord
M
(economy model beds only), mattress retainer bar
B
and foot end of bed to bed base.
L
NOTE: Deluxe Model Beds - If a head board is not being
Y
used, remove the adjustable head board brackets. Refer to
REMOVING ADJUSTABLE HEAD BOARD BRACKET
in this section of the manual.
NOTE: Deluxe Model Beds - If two (2) twin beds are being
used together with a king size head board, only the two (2)
OUTSIDE adjustable head board brackets will be used.
The two (2) INSIDE adjustable head board brackets should
be removed. Refer to REMOVING ADJUSTABLE
HEAD BOARD BRACKET in this section of the manual.
NOTE: Deluxe Model Beds - If two (2) twin beds are being
used together as a king size bed, the frequency channels
of the pendants can be set so the two (2) twin beds will
operate with one (1) pendant.Refer to CHANGING FRE-
QUENCY CHANNEL in the FREQUENCY CHANNEL/
BATTERY section of this manual.
Installing Locking Casters
1. Position the stem of one (1) locking caster with the one
(1) of the caster sockets at the head or foot end of bed.
Make sure the locking casters are se-
cured to the bed frame, otherwise injury
or damage may occur.
2. Install the stem of the locking caster into the caster socket
until an audible "click" is heard. Make sure the caster
retaining ring enters the caster socket squarely and the
caster is secured to the bed frame.
3. Repeat STEPS 1-2 for the remaining casters.
Removing bed from carton requires two
(2) people, otherwise injury or damage
may occur.
4. Remove bed from the bottom half of the shipping carton.
5. Set the bed onto all four (4) locking casters.
Installing Mattress Retainer Bar
1. Remove plastic sleeve from the mattress retainer bar.
2. Install mattress retainer bar onto the four (4) studs on the
underside of the bed as shown in FIGURE 1.
ASSEMBLY
WARNING
WARNING
3. Install the four (4) washers and wing nuts onto the four
(4) threaded studs and tighten securely.
Connecting Pendant
NOTE: This procedure is for economy model beds only.
1. Remove the back plate of the pendant.
2. Plug the pendant cord from the electrical control box
into the plug in the pendant.
3. While holding the pendant cord in the slot on the pen-
dant, reinstall the back plate.
Installing Mattress
CAUTION
Protective covers MUST be removed to
ensure proper ventilation and avoid the
possibility of mildew and musty odors.
1. Remove protective cover from base and mattress.
2. Place the mattress on the base.
NOTE: The mattress may be placed onto the bed either
side up and may be turned and rotated head to foot.
Installing a Head Board
NOTE: Head boards can be assembled onto deluxe
model beds only.
NOTE: Deluxe Leisure Beds are designed to be used
with your head board.
CAUTION
The head board MUST rest on the floor.
Adjustable head board brackets are not
designed to support the full weight of the
head board.
1. Swing the two (2) adjustable head board brackets
(attached to the bed) to the open position as shown in
FIGURE 1.
2. Remove the two (2) wing nuts and mounting screws
that secure the two pieces of the adjustable head board
bracket together.
3. Adjust length of the adjustable head board bracket
until the end of bracket clears the end of the mattress.
4. Reinstall the two (2) mounting screws that secure the
two pieces of adjustable head board bracket together.
5. Reinstall the two (2) wing nuts and tighten securely.
6. Attach a metal plate to the head board using the exist-
ing head board hardware.
7. Line up the mounting holes in the metal plate with the
mounting holes in the adjustable head board bracket
and insert a steel pin through all four (4) holes.
8. Repeat STEPS 2-7 for opposite head board bracket.
6
Advertisement
Table of Contents
