Related Manuals for Axis AXIS T90D20 IR-LED
Summary of Contents for Axis AXIS T90D20 IR-LED
-
Page 1: User Manual
AXIS T90D Illuminator Series AXIS T90D20 IR-LED AXIS T90D20 PoE IR-LED AXIS T90D25 W-LED AXIS T90D25 PoE W-LED AXIS T90D30 IR-LED AXIS T90D30 PoE IR-LED AXIS T90D35 W-LED AXIS T90D35 PoE W-LED AXIS T90D40 IR-LED User Manual... -
Page 2: Table Of Contents
How to re-enable the control buttons ....... How to control the illuminator with an Axis network camera ... . -
Page 3: Eye Safety Information
AXIS T90D Illuminator Series Eye safety information Eye safety information CAUTION IR variants: IR emitted from this product, EN62471 Risk Group 2. Do not stare at the lamp. Avoid exposure or use appropriate shielding or eye protection. Risk Group 2 for cornea/lens infrared hazard. For T90D20 and T90D30 variants the hazard distance is 1500 mm. -
Page 4: About This Manual
AXIS T90D Illuminator Series About this manual About this manual This user manual describes multiple products. Some of the instructions may not be relevant for your product. -
Page 5: Product Overview
AXIS T90D Illuminator Series Product overview Product overview Product overview Note The appearance of your product may differ from the following images. Photocell Power, photocell and telemetry for AC/DC versions or network cable for PoE versions Breather gland Wire configuration (AC/DC versions only) -
Page 6: Remote Control
AXIS T90D Illuminator Series Product overview Mounting bracket (pre-mounted) Control button (left) Left Hand Side LED (LHS) Right Hand Side LED (RHS) Control button (right) The baseplate must be removed in order to access the two control buttons. Remote control Note The remote control is an optional accessory. - Page 7 Product overview To control the product with an Axis network camera, connect the telemetry wires to the camera’s I/O connector. Connect the purple telemetry wire to pin 1 (DC ground), and the orange telemetry wire to pin 4 (digital output). For more information, see How to control the illuminator with an Axis network camera on page 10.
-
Page 8: Setup
AXIS T90D Illuminator Series Setup Setup About the factory default settings When you buy the product, the telemetry wires (see Product overview on page 5 ) are soldered together. This makes the illuminator turn on automatically when the photocell detects low-light conditions. -
Page 9: About Using A Pin
AXIS T90D Illuminator Series Setup 3. Press the right control button repeatedly until the right hand side LED turns solid green. How to change from programming to operating mode With the remote control 1. Press and hold the Disable remote control setup button for 4 seconds. -
Page 10: How To Disable The Control Buttons
How to control the illuminator with an Axis network camera This use case explains how to: • connect the illuminator to the I/O connector of an Axis network camera • set up the camera to make the illuminator turn on when the camera detects motion Connect the illuminator to an Axis network camera: 1. -
Page 11: How To Adjust The Light Intensity
4. To make the illuminator turn on when the camera detects motion, select Open circuit in the drop-down list. Verify in the camera’s webpage that the AXIS Video Motion Detection application is running: 1. Go to Settings > Apps > AXIS Video Motion Detection. -
Page 12: How To Adjust The Photocell Sensitivity
AXIS T90D Illuminator Series Setup 20% of maximum 40% of maximum 60% of maximum 80% of maximum 100% of maximum With the control buttons 1. Press the left control button once so that the left hand side LED turns solid red. -
Page 13: How To Enable Or Disable The Led Indicators
AXIS T90D Illuminator Series Setup Photocell disabled 5 lux on, 15 lux off 10 lux on, 30 lux off 25 lux on, 50 lux off With the control buttons 1. Press the left control button twice so that the left hand side LED turns solid green. -
Page 14: How To Reset To Factory Default Settings
AXIS T90D Illuminator Series How to reset to factory default settings How to reset to factory default settings You can choose to make a full reset or a settings reset. The full reset restores factory default settings and removes the PIN if one has been set. -
Page 15: Troubleshooting
AXIS T90D Illuminator Series Troubleshooting Troubleshooting Ensure all tests are undertaken by a qualified, trained engineer. Ensure safe working practices are followed at all times. • Basics Check the LED indicators. See LED Indicators on page 16. Check the polarity of the illuminator connection: red = +ve, black = -ve. -
Page 16: Specifications
Specifications Specifications To find the latest version of the product’s datasheet, go to the product page on axis.com and locate Support & Documentation. LED Indicators There are two colored LED indicators on the base of the illuminator which provide operating and status information. - Page 17 User Manual Ver. M1.10 AXIS T90D Illuminator Series Date: December 2017 © Axis Communications AB, 2017 Part No. T10116700...