Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Jet IBG-8VSB
Summary of Contents for Jet IBG-8VSB
- Page 1 This .pdf document is bookmarked Operating Instructions and Parts Manual 8-inch Variable Speed Buffing Machine Model IBG-8VSB 427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-578218 Ph.: 800-274-6848 Edition 2 04/2017 www.jettools.com Copyright © 2017 JET...
-
Page 2: Important Safety Instructions
Do not use this buffer for other than its intended its operation. A guard or other part that is damaged use. If used for other purposes, JET disclaims any should be properly repaired or replaced. real or implied warranty and holds itself harmless from any injury that may result from that use. - Page 3 31. Don’t use in dangerous environment. Don’t use 35. Maintain tools with care. Keep tools sharp and power tools in damp or wet location, or expose clean for best and safest performance. Follow them to rain. Don’t use this buffer in a flammable instructions lubricating changing...
-
Page 4: Table Of Contents
10.2 Digital readout error codes ........................12 11.0 Optional accessories ..........................13 12.0 Replacement Parts ............................. 13 12.1.1 IBG-8VSB Buffer – Exploded View ..................... 14 12.1.2 IBG-8VSB Buffer – Parts List ......................15 12.2.1 IBG-Stand Assembly (OPTIONAL) – Exploded View ................16 12.2.2 IBG-Stand Assembly (OPTIONAL) –... -
Page 5: About This Manual
If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Specifications
= not applicable The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Setup And Assembly
24mm (or adjustable) wrench with all relevant codes. This tool must be properly grounded. The IBG-8VSB requires only the installing of buffing The IBG-8VSB Buffer is prewired for 115V single wheels. Additional fasteners and tools may be phase power, and is supplied with a plug designed... -
Page 8: Extension Cords
D, Figure angle). 7-1. A grounding plug may be installed, that looks The JET Buffer is provided with two buffing wheels: like the plug illustrated in D; or the grinder may be a full spiral-sewn wheel for general polishing of “hard-wired”... -
Page 9: General Procedure
Always use approved safety glasses or face shield while operating buffer. Also use appropriate respiratory protection. 8.1 General procedure Turn on buffer and apply compound to lower part of spinning wheel (not the workpiece). Do apply excessive compound; press compound stick lightly against wheel for only a few seconds. -
Page 10: Buffer Maintenance
9.2.2 Correcting side-to-side wobble 9.3 Buffer maintenance Periodically use a wheel rake (not provided) to clean The IBG-8VSB Buffer has large, machined flanges, and shape the buffing wheels. making wobble unlikely if a good quality buffing wheel is used. Should a wheel exhibit need for 9.4 Additional servicing... -
Page 11: Troubleshooting Ibg-8Vsb Buffer
10.0 Troubleshooting IBG-8VSB Buffer 10.1 General electrical and mechanical problems Table 3 Symptom Possible Cause Correction * Motor will not start. Not connected to power source. Verify that plug is properly inserted into receptacle. Motor cord cut or abraded. Replace with new cord. -
Page 12: Digital Readout Error Codes
Symptom Possible Cause Correction * Motor slows. Motor overloaded. Reduce load to motor; do not press so hard. Low line voltage. Check power line for proper voltage. Loose electrical connections. Inspect connections. Frequent fuse or circuit Motor overload. Reduce load to motor; do not press so breaker failure. -
Page 13: Optional Accessories
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET. Some parts are shown for reference only, and may not be available individually. -
Page 14: Ibg-8Vsb Buffer - Exploded View
12.1.1 IBG-8VSB Buffer – Exploded View... -
Page 15: Ibg-8Vsb Buffer - Parts List
34 ....IBG8-47 ..... Strain Relief ....................1 35 ....IBG8-46 ..... Power Cord with 15A Plug ........16AWG x 3C SJT ..1 ....LM000285 ....ID/Warning Label, IBG-8VSB (not shown) ............ 1 ....JET-92 ....... JET Logo (not shown) ..........92x38mm ...... 1... -
Page 16: Ibg-Stand Assembly (Optional) - Exploded View
12.2.1 IBG-Stand Assembly (OPTIONAL) – Exploded View 12.2.2 IBG-Stand Assembly (OPTIONAL) – Parts List Index No. Part No. Description Size ....578172 ...... IBG-Stand for Bench Grinders (#1 thru 13) ........... 1 1 ....IBGS-01 ....Base....................... 1 2 .... -
Page 17: Dbg-Stand Assembly (Optional) - Exploded View
12.3.1 DBG-Stand Assembly (OPTIONAL) – Exploded View 12.3.2 DBG-Stand Assembly (OPTIONAL) – Parts List Index No. Part No. Description Size ....578173 ...... DBG-Stand for Bench Grinders (#1 thru 14)..........1 1 ....DBGS-01 ....Platform ......................1 2 .... -
Page 18: Electrical Connections For Ibg-8Vsb
13.0 Electrical Connections for IBG-8VSB... -
Page 19: Warranty And Service
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason ®... - Page 20 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com...
Need help?
Do you have a question about the IBG-8VSB and is the answer not in the manual?
Questions and answers