Subscribe to Our Youtube Channel
Related Manuals for Wheatstone E-Series
Summary of Contents for Wheatstone E-Series
- Page 1 V M I erieS irTual ixer nTerface echnical ocumenTaTion 600 Industrial Drive, New Bern, N.C. 28562 (tel 252-638-7000 / fax 252-637-1285 / email@wheatstone.com )
- Page 2 V M I erieS irTual ixer nTerface echnical ocumenTaTion Wheatstone Corporation August 2010...
- Page 3 E-Series Virtual Mixer Interface Revised ©2016 Wheatstone Corporation 600 Industrial Drive New Bern, North Carolina 28562 tel 252-638-7000 / fax 252-637-1285...
-
Page 4: Table Of Contents
V I R T U A L M I X E R I N T E R F A C E Virtual Mixer Interface Contents Introduction ..................2 Host Controller (HC-3) ..............2 HC-3 BIOS Settings/Format ..................2 Installation and Rack Mounting .............3 Power Supply ...................3 I/O Connections ................4 Audio Network Wiring.................... -
Page 5: Introduction
(TDM-based), a Wheatstone Wheatnet system (also TDM-based), or a Wheatstone WheatNet ‑ IPsystem(IP‑based).TheVMIunitispre‑configuredatthefactoryforthetype of system it will be used with, and in particular E-Series Model that it will emulates. The total number of faders emulated is also set at the factory. -
Page 6: Installation And Rack Mounting
V I R T U A L M I X E R I N T E R F A C E Installation and Rack Mounting TheVMIisdesignedtofitintoanindustrystandard19”equipmentracks,and r equires onerackunit(1.75inches)ofverticalspace.Verticalslotspositionedinthesidepanels allowairflowtoandfromtheVMI.Additionallyaninternalfandirectstheairtocool componentsasrequired.Wheninstallingitisimportanttoavoidrestrictingairflowin andaroundthevents. The VMI may be mounted between other devices in an equipment rack, and in ... -
Page 7: I/O Connections
TheENETRJ‑45connectstheVMItoyourEthernetLANviastraight(pintopin) CAT5/6 cable. The LAN (Local Area Network) connection is for communicating with computersrunningWheatstonesoftwaresuchasXPoint,PC‑XYC,andEventComputer. In the case of a WheatNet-IP system, this link also carries the settings and commands normally carried on the AT LINK connection in TDM systems. If you are connecting directly between a PC and the VMI using this link, with no network switch or hub in between,... -
Page 8: Typical Cat5/6 Cabling
V I R T U A L M I X E R I N T E R F A C E eTH C PIN D oNNeCTor eTAIL 1 – TXD + 2 – TXD - 3 – RXD + 4 – n/C 5 –... -
Page 9: Rj-45 Connections
V I R T U A L M I X E R I N T E R F A C E RJ-45 Connections Ethernet Connector Mixer (AT) Link CAT5 (RJ-45) Connector (RJ-45) TXD + TXD + TXD - TXD - RXD + RXD + (crossover) -
Page 10: Using The Vmi
E-Series console surface. Refer to E-Series Surface manual that matches your VMI versionformoredetailsonoperationalinformation. GLASS E Software YoucanconfiguretheVMItoacceptGLASSEconnectionsonaspecifiedport.Oncesetup, youcanconfigureGLASSEsoftwaretoconnecttotheVMIasifitwereanE‑SeriesSurface. Refer to the E-Series Surface manual that you are emulating in your VMI for operational details. page 7 VMI / Nov 2016...
Need help?
Do you have a question about the E-Series and is the answer not in the manual?
Questions and answers