Table of Contents
Advertisement
Installation Manual
Quidway S5000 Series Ethernet Switches
Chapter 1 Product Overview ........................................................................................................ 1-1
1.1 Introduction ........................................................................................................................ 1-1
1.2 S5012G and S5012G-DC Switches................................................................................... 1-2
1.2.1 Front View ............................................................................................................... 1-2
1.2.2 Rear View................................................................................................................ 1-5
1.3 S5012G and S5012G-DC Switches................................................................................... 1-6
1.3.1 Front View ............................................................................................................... 1-6
1.3.2 Rear View................................................................................................................ 1-6
1.4 S5024G-24/20TP and S5024G-24/20TP-DC .................................................................... 1-7
1.4.1 Front View ............................................................................................................... 1-7
1.4.2 Rear View................................................................................................................ 1-7
1.5 Attributes of Console Port.................................................................................................. 1-7
1.6 Attributes of GBIC Ports .................................................................................................... 1-8
1.7 Attributes of GE Ports (RJ-45 connector) .......................................................................... 1-9
1.8 S5000 Series Product Specifications................................................................................. 1-9
Chapter 2 Installation Preparation............................................................................................... 2-1
2.1 Safety Requirements ......................................................................................................... 2-1
2.2 Examine Installation Location ............................................................................................ 2-1
2.2.1 Temperature/Humidity Requirements ..................................................................... 2-1
2.2.2 Cleanness Requirements........................................................................................ 2-2
2.2.3 Anti-interference Requirements .............................................................................. 2-2
2.2.4 Laser Usage Security.............................................................................................. 2-3
2.3 Installation Tools ................................................................................................................ 2-3
Chapter 3 Installation .................................................................................................................... 3-1
3.1 Installing the Switch ........................................................................................................... 3-1
3.1.1 Racking-Mounting the Switch in 19-inch Rack........................................................ 3-1
3.1.2 Free-Standing the Switch on a Tabletop................................................................. 3-2
3.2 Connection of Power Cord and Grounding wire ................................................................ 3-2
3.2.1 Connecting AC Power Cord .................................................................................... 3-2
3.2.2 Connecting DC Power Cord.................................................................................... 3-3
3.2.3 Redundant Power Input (Optional) ......................................................................... 3-4
3.2.4 Connecting Grounding Wire.................................................................................... 3-4
3.3 Connecting Console Cable ................................................................................................ 3-7
3.3.1 Console Cable......................................................................................................... 3-7
3.3.2 Connecting Console Cable ..................................................................................... 3-8
3.4 Post-installation Checklist.................................................................................................. 3-8
Table of Contents
Huawei Technologies Proprietary
i
Table of Contents
Advertisement
Table of Contents
Related Manuals for Quidway S5012G-DC
Summary of Contents for Quidway S5012G-DC
-
Page 1: Table Of Contents
Table of Contents Table of Contents Chapter 1 Product Overview ......................1-1 1.1 Introduction ........................1-1 1.2 S5012G and S5012G-DC Switches................... 1-2 1.2.1 Front View ....................... 1-2 1.2.2 Rear View........................ 1-5 1.3 S5012G and S5012G-DC Switches................... 1-6 1.3.1 Front View ....................... 1-6 1.3.2 Rear View........................ - Page 2 Installation Manual Quidway S5000 Series Ethernet Switches Table of Contents Chapter 4 Powering on Switch for the First Time ..............4-1 4.1 Establish configuration environment.................. 4-1 4.2 Connecting the Console Cable ..................4-1 4.3 Setting Terminal Parameters ..................... 4-1 4.4 Booting Switch ........................4-5 4.4.1 Check before Powering on the Switch ..............
-
Page 3: Chapter 1 Product Overview
Ethernet ports (RJ-45 connector) and 4 Combo GBIC (Gigabit Interface Converter) ports. S5012G-DC: It is powered by DC supply. Its port configuration is identical with that of the S5012G. S5012T-12/10GBC: It is powered by AC supply and provides 10 GBIC ports, 2 10/100/1000BASE-T Ethernet ports and 2 Combo RJ45 ports. -
Page 4: S5012G And S5012G-Dc Switches
1.2 S5012G and S5012G-DC Switches 1.2.1 Front View Note: S5012G and S5012G-DC have the same front panels. The following description is based on S5012G. I. Front panel You can find the system status indicators (RUN, MPS and RPS), indicator mode control... - Page 5 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 1 Product Overview System status indicators MODE Port status 12 GE interfaces Console port mode indicators 4 GBIC interfaces Figure 1-1 S5012G front panel II. Indicators on front panel The indicator meaning on the front panel of S5012G is listed in the table below.
- Page 6 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 1 Product Overview Table 1-2 Port status mode indicators of S5012G switch Status Description 10/100/1000M Description Indicator Status 1000M optical port electric port (copper (optical fiber) wire) The port is connected to the peer device and the link is normal.
-
Page 7: Rear View
Maximum voltage range: 90-264V a.c.; 50/60Hz II. Rear panel of S5012G-DC Rear panel You can find DC power socket, grounding and redundant power socket located in order on the rear panel of S5012G-DC. See the figure below. DC power Grounding Redundant power... -
Page 8: S5012G And S5012G-Dc Switches
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 1 Product Overview 1.3 S5012G and S5012G-DC Switches 1.3.1 Front View Note: S5012T-12/10GBC and S5012T-12/10GBC-DC have the same front panels. The following description is based on 5012T-12/10GBC, and S5012T stands for both S5012T-12/10GBC and S5012T-12/10GBC-DC. -
Page 9: S5024G-24/20Tp And S5024G-24/20Tp-Dc
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 1 Product Overview 1.4 S5024G-24/20TP and S5024G-24/20TP-DC 1.4.1 Front View Note: S5024G-24/20TP and S5024G-24/20TP-DC have the same front panels. The following description is based on S5024G-24/20TP, and S5024G stands for both S5012T-12/10GBC and S5012T-12/10GBC-DC. -
Page 10: Attributes Of Gbic Ports
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 1 Product Overview Table 1-3 Attributes of Console port Attribute Description Connector RJ-45 Port standard Asynchronous EIA/TIA-232 Baudrate 9600bps (default) Connecting with ASCII terminals Function Connecting with local terminals (PCs) or remote terminals (with a pair of Modems) and running terminal emulation program 1.6 Attributes of GBIC Ports... -
Page 11: Attributes Of Ge Ports (Rj-45 Connector)
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 1 Product Overview 1.7 Attributes of GE Ports (RJ-45 connector) The attributes of GE ports (RJ-45 connector) on S5000 Series are listed in the following table. Table 1-5 Attributes of GE ports (RJ-45 connector) - Page 12 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 1 Product Overview S5012 S5012T S501 S5012G T-12/1 S5024G- S5024G-24/2 Item -12/10G 0GBC- 24/20TP 0TP-DC Extended slot Rated voltag range: Rated Rated Rated Rated 100-2 voltage voltage voltage voltage range: range: range: range: a.c.;...
-
Page 13: Chapter 2 Installation Preparation
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 2 Installation Preparation Chapter 2 Installation Preparation 2.1 Safety Requirements To avoid any device impairment and bodily injury because of improper uses, please follow the precautions listed below: Before cleaning the switch, please unplug the switch connector first. Do not clean the switch with wet cloth or with liquid. -
Page 14: Cleanness Requirements
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 2 Installation Preparation Meanwhile, the electrostatic is likely to be produced in the dry environment, which will jeopardize the CMOS circuit of the switch. The higher the temperature, the greater the damage it will do to the Switch. Long-lasting high temperature will speed up the aging process of the insulating materials, greatly lower the reliability of the switch, and therefore affect its service life seriously. -
Page 15: Laser Usage Security
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 2 Installation Preparation electromagnetic wave, common impedance (including the grounding system) coupling or conducting line (power line, signaling line and transmission line etc.). To prevent the interference, you should: If AC supply system is TN system, AC power socket should be a single-phase three-line power socket with Protection Earth (PE). -
Page 16: Chapter 3 Installation
Chapter 3 Installation Caution: On a mounting screw of Quidway series switches' chassis, there is an anti-dismantle seal of Huawei Technologies. The seal must be kept intact before the sales agent performs maintenance on the switch. Users should contact local agent for permission if it is necessary to open the chassis. -
Page 17: Free-Standing The Switch On A Tabletop
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 3 Installation Note: The mounting ears are used for fixing rather than bearing. When mounted in a 19-inch standard rack, the switch is borne by slide rails (fixed on the rack). 3.1.2 Free-Standing the Switch on a Tabletop If you have no 19-inch standard rack, you may just place the switch on a clean tabletop, which is a relatively easy way to operate. -
Page 18: Connecting Dc Power Cord
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 3 Installation Caution: Before powering on the switch, connect the grounding wire first. 3.2.2 Connecting DC Power Cord NEG(-): -48V RTN(+): -48V working ground Figure 3-3 DC power socket Step 1: Connect one end of the chassis group cable, which is attached to the switch in delivery, to the grounding screw on the rear panel of the switch. -
Page 19: Redundant Power Input (Optional)
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 3 Installation 3.2.3 Redundant Power Input (Optional) Caution: The redundant power cord is not hot-swappable. I. Redundant power input To make S5000 Series more reliable, redundant power module is provided. The module has a 12V DC external port, which is connected to Huawei RPS (Redundant Power System) through DC power cord. - Page 20 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 3 Installation Caution: The correct connection of the switch grounding wire is the primary guarantee for the lightning protection and anti-interference; so users must connect the grounding wire correctly. Note: The following figures just illustrate processing method of grounding screws or grounding at power input end, but no switch type and accurate positions of power input end and grounding screws are specified.
- Page 21 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 3 Installation Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch Grounding screw Grounding screw Grounding screw Grounding screw Power input Power input Power input Power input Grounding wire Grounding wire Grounding wire...
-
Page 22: Connecting Console Cable
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 3 Installation Ethernet Switch Ethernet Switch Ethernet Switch Ethernet Switch AC/DC AC/DC AC/DC AC/DC power box power box power box power box -48V strip -48V strip -48V strip -48V strip -48V -48V... -
Page 23: Connecting Console Cable
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 3 Installation 3.3.2 Connecting Console Cable Follow these steps to connect a terminal device, a PC for example, to the switch: Step 1: Plug the DB-9 female connector of the Console cable to the serial port of the PC where the switch is to be configured. -
Page 24: Chapter 4 Powering On Switch For The First Time
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 4 Powering on Switch for the First Time Chapter 4 Powering on Switch for the First Time 4.1 Establish configuration environment Setting up the configuration environment (the following figure is as reference): The terminal (a PC in this example) is connected to the Console port of the switch through a Console cable. - Page 25 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 4 Powering on Switch for the First Time Figure 4-2 Connection description interface of HyperTerminal Key in the name of the new connection in the connection description interface and click <OK>, the following interface will pop up. Select the serial port to be used from [Connect using].
- Page 26 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 4 Powering on Switch for the First Time Click <OK> after the serial port is selected and the following interface will pop up. Set the baud rate to 9600, data bit to 8, parity to none, stop bit to 1, and flow control to none.
- Page 27 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 4 Powering on Switch for the First Time Figure 4-5 HyperTerminal Select [Properties] in the HyperTerminal dialog box to enter the properties window. Click [Settings] in the property setting window as the following figure and select VT100 as the emulation terminal.
-
Page 28: Booting Switch
The terminal display may change for different models. The display of S5012G is shown in the following example. starting ..*************************************** * Quidway S5012G BOOTROM, Version 121 *************************************** Copyright(C) 2000-2004 by HUAWEI TECHNOLOGIES CO.,LTD. Creation date : Jun 24 2005, 10:08:37... - Page 29 <Quidway> By this time, the user can start configuring the switch. Note: Quidway series switches provide diverse command modes. For introduction of the configuration commands and command line interfaces in detail, refer to Quidway S5000 Series Ethernet Switches Operation Manual.
-
Page 30: Chapter 5 Bootrom And Host Software Loading
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 5 BootROM and Host Software Loading Chapter 5 BootROM and Host Software Loading 5.1 Introduction to Loading Approaches This chapter introduces how to load BootROM and host software for a switch at the local and the remote. -
Page 31: Boot Menu
Take S5012G Switch as an example. After being powered on, the switch runs the BootROM program first and displays the following information on the screen: starting ..*************************************** * Quidway S5012G BOOTROM, Version 121 *************************************** Copyright(C) 2000-2004 by HUAWEI TECHNOLOGIES CO.,LTD. Creation date... -
Page 32: Loading Software From Console Port Using Xmodem
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 5 BootROM and Host Software Loading Input the correct BootROM password (by default, no password is set on the switch). The system enters the following Boot Menu: Caution: Please remember the BootROM password you have modified when using the switch. - Page 33 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 5 BootROM and Host Software Loading 1. Set TFTP protocol parameter 2. Set FTP protocol parameter 3. Set XMODEM protocol parameter 0. Return to boot menu Step 2: Press <3> in the loading menu, choosing to download the BootROM program using XModem.
- Page 34 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 5 BootROM and Host Software Loading Figure 5-1 “Properties” dialog box Figure 5-2 “Console Port Configuration” dialog box Huawei Technologies Proprietary...
- Page 35 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 5 BootROM and Host Software Loading Step 6: Click <Disconnect> to disconnect the HyperTerminal from the switch and then click <Connect> to re-establish the connection, thus validating the baud rate setting. Figure 5-3 <Disconnect> and <Connect>...
- Page 36 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 5 BootROM and Host Software Loading Figure 5-5 “Sending File” Interface After completing the loading, the system displays the following information: Loading ...CCCCCCCCCC done! ## Total Size = 0x00055d40 = 351552 Bytes Your baudrate should be set to 9600 bps again! Press enter key when ready.
-
Page 37: Loading Software From Ethernet Port Using Tftp
Caution: TFTP Server program is not provided with the Quidway Series Switches. Step 3: Run terminal emulation program on the PC that is connected to the Console port. Start the switch, access Boot Menu, and then enter download protocol menu. -
Page 38: Loading Software From Ethernet Port Using Ftp
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 5 BootROM and Host Software Loading Server IP address Step 5: Input the TFTP parameter values and press <Enter>. The system displays the following information: Are you sure to update your bootrom?(Y/N) Step 6: Press <Y>... - Page 39 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 5 BootROM and Host Software Loading To download the BootROM program, press <Ctrl + U> to access the menu for BootROM downloading when the system displays: ”Enter your choice (0-5):” Enter your choice(0-5): Please set bootrom download protocol parameter: 1.
-
Page 40: Remote Software Loading
<Quidway> boot boot-loader SWITCH.app <Quidway> display boot-loader The app to boot at the next time is: flash:/SWITCH.app <Quidway> reboot (Please make sure that you have saved other configurations before rebooting, otherwise, they might not survive a reboot.) Huawei Technologies Proprietary... -
Page 41: Remote Loading Using Tftp
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 5 BootROM and Host Software Loading BootROM and host software loading is completed now. Please note that you must reboot the switch to validate host software downloading. If Flash memory space is not enough, you can delete some of the program files in Flash after completing the BootROM loading. -
Page 42: Chapter 6 Maintenance And Troubleshooting
Installation Manual Quidway S5000 Series Ethernet Switches Chapter 6 Maintenance and Troubleshooting Chapter 6 Maintenance and Troubleshooting 6.1 Dealing with Load Failure If loading fails, the original version will remain in the system. In this case, check that the physical ports are correctly and well connected. If they are not, reconnect them correctly and restart loading procedures. - Page 43 Installation Manual Quidway S5000 Series Ethernet Switches Chapter 6 Maintenance and Troubleshooting has any faults, there will not be any screen display at the configuration terminal or the displayed characters will be totally illegible. I. Troubleshooting when there is no terminal display...
Need help?
Do you have a question about the S5012G-DC and is the answer not in the manual?
Questions and answers