Related Manuals for Emerson M11S-S
Summary of Contents for Emerson M11S-S
- Page 1 Installation, Operation and Maintenance Manual 121960, Rev. C June 2012 M11S-S Hydraulic Control System For "G" Series Spring Return Actuators...
-
Page 3: Table Of Contents
Section 7: Document Revision ����������������������������������������������8 Appendix A: List of Drawings ������������������������������������������������9 Part No. 121107, Assembly Dwg M11S-S G4/G8, Sheet 1 of 2 ....... 9 Part No. 121107, Assembly Dwg M11S-S G4/G8, Sheet 2 of 2 ..... 10 Table of Contents... -
Page 4: Section 1: Introduction
1�1 System Description M11S-S Hydraulic Control System is a compact, modular system designed for use with Bettis spring return actuators. The system incorporates a piston type hand pump and a make-up oil reservoir necessitated by the differential volume of the hydraulic cylinder (the differential volume is due to the inboard piston rod displacement). -
Page 5: Section 2: General Information
June 2012 Section 2: General Information CAUTION: FOLLOW PROPER MOUNTING PROCEDURES The M11S-S package must be mounted with the pump and reservoir upright and vertical. The reservoir fill plug must be removed and replaced, with the breather supplied, before operation. -
Page 6: Section 3: Actuator Power Operation
Fully open the M11S-S by-pass control valve (30). NOTE: The valve is located on the right hand side of the M11S-S control module. CAUTION: DO NOT EXCEED OPERATING PRESSURE Do not exceed the maximum operating pressure rating of the actuator. -
Page 7: Section 4: Actuator M11S-S Manual Operation
Continued operation of the pump simply circulates fluid through a high pressure relief. Fully open the M11S-S by-pass control valve (30) to reverse the actuator rotation or to return to normal power operation. Actuator M11S-S Manual Operation... -
Page 8: Section 5: Sytem Refilling
5.2.1 Shut off and exhaust the operating media from the actuators power cylinder. 5.2.2 Allow the actuator to fully stroke to its fail position by opening the M11S-S by-pass control (30) valve. 5.2.3 Remove the breather (150) from the reservoir end cap (25). - Page 9 5.3.10 and proceed as follows: 5.3.12 Close the M11S-S block (10) by-pass control valve (30). 5.3.13 Operate the M11S-S hand pump as described in section 4.0 to cycle actuator. 5.3.14 Replace the hydraulic cylinder inboard top o-ring plug when fluid appears. Stop operation of pump.
-
Page 10: Section 6: Maintenance
Bettis does not recommend periodic field maintenance for the M11S-S module and pump. The only time the M11S-S module or pump should be disassembled is when either the pump or the M11S-S module fails to perform its override function. If maintenance is required and when possible the M11S-S package should be returned to the factory for maintenance. -
Page 11: Section 7: Document Revision
Installation, Operation and Maintenance Manual Section 7: Document Revision 121960 Rev. C June 2012 Section 7: Document Revision Table 1� Revision Overview DATE BY * DATE Released September, 1997 A COMPILED COLBY 22 JUNE 06 19110 July, 2006 CHECKED JOHN R 6/22/06 APPROVED DAVID MCGEE... -
Page 12: Appendix A: List Of Drawings
Installation, Operation and Maintenance Manual Appendix June 2012 121960 Rev. C Appendix: A List of Drawings A�1 Part No� 121107, Remote Mount Assembly Dwg M11S-S G4/G8 For Fire Safe, Sheet 1 of 2 Apppendix... -
Page 13: Part No. 121107, Assembly Dwg M11S-S G4/G8, Sheet 2 Of 2
Installation, Operation and Maintenance Manual Appendix 121960 Rev. C June 2012 A�2 Part No� 121107, Remote Mount Assembly Dwg M11S-S G4/G8 For Fire Safe, Sheet 2 of 2 Appendix... - Page 15 ©2017 Emerson. All rights reserved. No. 1 Lai Yuan Road EUROPE Wuqing Development Area The Emerson logo is a trademark and service mark of Emerson Electric Co. Tianjin 301700 Berenyi u. 72- 100 Bettis is a mark of one of the Emerson family of companies.