Delta Tau Power PMAC Reference Manual
Delta Tau Power PMAC Reference Manual

Delta Tau Power PMAC Reference Manual

Software reference manual
Hide thumbs Also See for Power PMAC:

Advertisement

5" Side View Complete Camera System
Thank you for purchasing a Vision Works camera system. We have taken great care to provide you with a top quality
product. Vision Works comes with a one year warranty that covers defective materials or workmanship, as long as no
wiring or parts are modified in any manner. If our product is found to be modified the warranty will be nullified.
Please read and follow the owner's manual for installation and operation of your camera system.
No merchandise should be returned to Vision Works for credit unless accompanied by a return authorization number from
our company. You will receive credit for the full amount of the return, if the merchandise is returned within 30 days of the
invoice date. Any merchandise that is not returned within 30 days of the invoice date is subject to a restocking fee of 15%.
Contact your Vision Works dealer for return information.
Merchandise that has been special ordered cannot be returned for credit. Non-stock items returned for credit will be
subject to vendor's return policy.
1.
To prevent short circuit, make sure that the system is not plugged in or receiving power while making system
connections. In the event of a system short circuit, replacement of the 3A fuse will be required. Fuses are
located under the threaded tip of the cigarette lighter, and inside the threaded barrel section of the RED 12volt
supply wire. Replacement fuses are not included with this kit.
2.
To ensure that you do not drain your battery, it may be necessary to disconnect the cigarette adaptor when not
in use.
3.
The camera is completely weatherproof but the monitor is NOT and should NOT be exposed to water. Please
ask about weatherproof monitors if you have no cab.
Owner's manual
(VWIC500-SV)

Warranty Information

Return Policy:
Important!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Power PMAC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Delta Tau Power PMAC

  • Page 1 5” Side View Complete Camera System Owner’s manual (VWIC500-SV) Warranty Information Thank you for purchasing a Vision Works camera system. We have taken great care to provide you with a top quality product. Vision Works comes with a one year warranty that covers defective materials or workmanship, as long as no wiring or parts are modified in any manner.
  • Page 2 1.0 Specifications Monitor Specifications Camera Specifications Model 5” Model Sony Screen Size 5 inch Resolution 700 TVL Aspect Ratio 16:9 Lens 3.6 mm Luminance 350cd/m2 No. of Pins Weatherproof Resolution 400*R.G.B*272 Rating IP68 2 video/2 audio input (dual Audio & channel, single image Low Temp -20 C...
  • Page 3 Video Extension Quantity 1 Cable (30ft) Cigarette Lighter Quantity 1 Adapter AV Accessory Cable Quantity 1 Self-Adhesive Quantity 1 Bracket Suction Cup Quantity 1 Bracket...
  • Page 4 3.0 Assembly Instructions Option 1: Self Adhesive Base Installation – Camera can be mounted using magnet and install monitor onto monitor base that contains attaching hardware. These are the steps 3M self-adhesive tape backing. Ensure the four required to attach the magnet to the camera. plastic tabs on base are locked into position on rear of monitor.
  • Page 5 Connect VIDEO EXTENSION CABLE harness to C1 input on MAIN HARNESS. Ensure arrows are aligned on outer jacket of cable ends. Turn silver cable connector nut clockwise to secure the connection of the cables. Do not over tighten. Pull rubber sleeve membrane over cable connection.
  • Page 6 4.2 Power Cable Connection Installation: Cigarette Lighter Adapter - system can be powered by connecting the MAIN HARNESS CIGARETTE LIGHTER INPUT to the mating connector of the CIGARETTE LIGHTER ADAPTER. The cigarette lighter adapter can now be installed into a 12VDC power source. To verify that the system is receiving power, cup your hands over the camera lens, and the LED lights will have a red glow.

Table of Contents