LG L332-BN Owner's Manual

Color video camera
Hide thumbs

Advertisement

Quick Links

OWNER'S MANUAL
Color Video Camera
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
L332-BN/BP/CP

Advertisement

loading

  Also See for LG L332-BN

  Related Manuals for LG L332-BN

  Summary of Contents for LG L332-BN

  • Page 1 OWNER'S MANUAL Color Video Camera Please read this manual carefully before operating your set and retain it for future reference. MODEL L332-BN/BP/CP...
  • Page 2 FCC WARNING: This equipment may generate or use radio CAUTION frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction RISK OF ELECTRIC SHOCK manual. The user could lose the authority to operate this DO NOT OPEN equipment if an unauthorized change or modification is made.
  • Page 3 • Caution: Danger of explosion if battery is incorrectly Caution: This installation should be made by a qualified replaced. Replaced only with the same or equivalent service person and should conform to all local codes. type recommended by the manufacturer. Dispose Caution: To avoid electrical shock, do not open the of used batteries according to the manufacturer’s cabinet.
  • Page 4 LG Electronics hereby declares that this/ Disposal of your old appliance these product(s) is/are in compliance with the essential requirements and other rel- When this crossed-out wheeled bin evant provisions of Directive 2004/108/EC, symbol is attached to a product it means 2006/95/EC, and 2009/125/EC.
  • Page 5: Important Safety Instructions

    Important Safety Instructions Read these instructions. and the point where they exit from the apparatus. Keep these instructions. 11. Only use attachments/accessories specified by the manufacturer. Heed all warnings. 12. Use only with the cart, stand, tripod, bracket, or table Follow all instructions.
  • Page 6: Cautions For Safe Operation

    Cautions for Safe Operation Power Supply use a cloth dampened with a small quantity of neutral detergent then wipe dry. L332-BN / L332-BP: • Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides. This camera must always be operated by AC 24 V or DC 12 They may damage the surface finish and/or impair the V Certified/Listed, class 2 power supply only.
  • Page 7: Table Of Contents

    Contents Features ..............8 OSD Menu Overview ...........22 General Operation ............25 Part Names and Functions ........9 Camera Identification Settings ........25 Exposure Settings ............26 Connections ............12 White Balance settings ..........29 Day/Night Setting ............30 Precautions ..............12 Motion Detection Setting ..........31 Connection Overview ..........12 3D-DNR Setting .............32 Connecting Display device........13...
  • Page 8: Features

    Features This Color Video Camera is designed for installation in an video surveillance system. This manual contains instructions on how to install and manage the Color Video Camera in your video surveillance system. Should you require any technical assistance, please contact authorized service center.
  • Page 9: Part Names And Functions

    Part Names and Functions c Flange-back adjustment lever b c d d Lens iris output connector (LENS) This 4- pin connector is used to send the Iris control signal and power supply to an auto-iris type lens. e Setup menu control buttons Use these buttons to set the menu options.
  • Page 10 Part Names and Functions f Power input terminal L332-BN/ L332-BP Supplies AC 24 V or DC 12 V from an external power source. g External Device Connectors • D&N Connect the external switch to set the D&N function manually. •...
  • Page 11 Part Names and Functions f Power cable L332-CP g External Device Connectors • D&N Connect the external switch to set the D&N function manually. • ALARM (Alarm Output Terminal) Connect to the alarm input of an external device. • COM (COMMUNICATION) Connect to an external controller of RS-485 format.
  • Page 12: Connections

    Connections Precautions • Be sure to switch off the unit before installation and connection. • A qualified service person, complying with all applicable codes, should perform all required hardware installation. • Do not expose the power and connection cable to moisture, which may cause damage to the unit. Connection Overview RS-485 Unit External D&N...
  • Page 13: Connecting Display Device

    Connections Connecting Display device Connecting Power Source The video signal connection between the camera and the L332-BN/ L332-BP monitor. Connect power, using the method listed below: Remove the insulation on the power cable as illustrated. (a) Attach the terminal tips. (b) Connect to the DC 12 V / AC 24 V UL Listed, Class 2 Power Supply only on the unit.
  • Page 14: Connecting Rs-485 Device

    Connections Connecting RS-485 Device L332-CP Use these ports to connect an external device of RS-485 Insert the plug of the power cord into a wall outlet. The format. POWER indicator will light. Tx(+) RS-485 Unit Rx(-)
  • Page 15: Connecting Alarm Device

    Connections Connecting Alarm Device Contact Ratings Alarm terminals are used to connect the alarm (relay) • Maximum load current is ALARM devices such as sensors, door switches, etc. ±130 mA. Connect the alarm (relay) device to the alarm (relay) output •...
  • Page 16: Connecting Day&Night Switch

    Connections Connecting Day&Night Switch Connect the external D&N switch to the D&N terminal. Night function When you close the external switch, the D&N function is set to night mode. Day function When you open the external switch, the D&N function is set to Day mod.
  • Page 17: Mounting The Lens

    Connections Mounting the Lens era opening and turn the lens slowly to install it. Remove the lens mount cap from the camera. Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. Install the auto-iris lens. When using lenses from other makers, the plug shape 2-1.
  • Page 18 Connections lens iris output connector Rewire the lens iris plug Pin layout for the lens iris output connector. Cut off the plug of the lens cable, cut off approximately 8 mm of the insulation, and then strip approximately 2 mm of the ends of the cable sheaths.
  • Page 19: Flange-Back Adjustment

    Connections Flange-back Adjustment Note: The object may be out of focus when using a source of The adjustment is required only when a lens without near-infrared light than using the visible light. focus-adjusting mechanism is mounted, or when a lens with adjusting mechanism is mounted and focus that is more accurate is needed.
  • Page 20: Mounting The Camera

    Connections Mounting the camera The mounting bracket can be secured on either the top or bottom of the camera. Use the same set of screws to attach the mounting bracket on the camera. Note: If using a camera mounting bracket, select a location that is strong enough to bear the full weight of the camera and the mounting bracket for long periods, and install the camera and mounting bracket securely.
  • Page 21: Menu Operation

    Menu Operation OSD Menu control buttons BUTTON Description This camera utilizes an on-screen user MENU. To set items Used to move upper direction on the on the menu, use the following buttons. menu screen. Use this button to select an item or adjust the parameters. UP button Used to move lower direction on the menu screen.
  • Page 22: Osd Menu Overview

    Menu Operation OSD Menu Overview Main Menu Sub Menu Contents NATURAL/COOL/ The following table shows the list of menu items and USER MODE WARM/VIVID options. You can adapt the camera to your requirements by NATURAL/COOL/ AUTO USER MODE setting up the respective items in these menus. WARM/VIVID PUSH INDOOR,...
  • Page 23 Menu Operation Main Main Contents Contents Menu Menu Menu Menu SMART MD ON/OFF ZONE AREA1 to RED, GREEN, NUMBER AREA4 COLOR 0 to 255 BLUE ZONE STATE ON/OFF TRANSPARENCY 0 to 16 HEIGHT 2 to 6 REGIONAL WIDTH 2 to 8 MASK NUMBER AREA1 to AREA8 MOVE Y 1 to 5...
  • Page 24 Menu Operation Main Menu Sub Menu Contents Main Menu Sub Menu Contents CAMERA REBOOT ZOOM RESET FACTORY RESET D-ZOOM EXIT RET/TOP/END TILT EXIT EXIT D-EFFECT OFF/ MIRROR/ ROTATE/ V-FLIP SHARPNESS 0 to 68 SPECIAL COLOR OFF/ ON STABILIZER OFF/ ON SYNC INT / LL USER TITLE...
  • Page 25: General Operation

    Menu Operation General Operation • RET: Return to the previous. • TOP: Return to the CAMERA SETTING menu Press [SET] button. screen. • END: Exit the setup menu. The setup menu screen appears on the monitor. Camera Identification Settings You can use the camera identification (CAMERA ID) to assign a number to the camera.
  • Page 26: Exposure Settings

    Menu Operation Exposure Settings WDR/BLC setting Use WDR/BLC option to view the object clearly in backlight You can set the exposure options using the EXPOSURE conditions. menu. Select [EXPOSURE] option on the [CAMERA SETTING] menu. Use [LEFT] or [RIGHT] button to select a mode (ALC2 ELC).
  • Page 27 Menu Operation > MASK: Use [LEFT] or [RIGHT] button to > WDR LIMIT: LOW MIDDLE HIGH select [ON] or [OFF]. > ACE (Adaptive Contrast Enhancement) : This If you set the MASK to ON, the mask function function is used when you want to display is activate only when the HSBLC is automati- dark areas of WDR brightly.
  • Page 28 Menu Operation AGC (Automatic Gain Control) setting SHUTTER (Shutter Speed) setting If the images are too dark, change the maximum [AGC] Select the desired shutter speed for camera exposure. You value to make the images brighter. can change the shutter speed to higher speed to capture fast-moving subjects, though the image becomes darker.
  • Page 29: White Balance Settings

    Menu Operation the camera is change to iris control mode automatically for button to set the SENS-UP limit. the camera exposure. Anti-flicker mode is not supported in > EXIT: Select a mode and press [SET] to exit the ALC2 mode. If you want to use it, select ALC mode . the menu.
  • Page 30: Day/Night Setting

    Menu Operation Use [LEFT] or [RIGHT] button to select a mode then to select a function. press [SET]. INDOOR: The color temperature range for the proper white balance is approxi- • ATW (Auto-Tracing White Balance): The color mately 3 200 K. temperature range for the proper white balance is approximately 1 700 K to 11 000 K.
  • Page 31: Motion Detection Setting

    Menu Operation Motion Detection Setting Use [LEFT] or [RIGHT] button to select mode for day/ night function. The motion detection detects the moving objects in the • AUTO: You will be able to change the Day/Night scene by monitoring changes in brightness level. You can mode automatically.
  • Page 32: 3D-Dnr Setting

    Menu Operation 3D-DNR Setting > Use [LEFT] or [RIGHT] button to select a zone number (AREA1 to AREA4) on the [ZONE NUMBER]. > Use [LEFT] or [RIGHT] button to set up the ON or OFF on the ZONE STATE. > Use [UP] or [DOWN] to select an option then use [LEFT] or [RIGHT] button to adjust the option.
  • Page 33: Privacy Setting

    Menu Operation Privacy Setting of MASK (0 to 16) • RECTANGLE : This function is aiming at the protection of personal Use [LEFT] or [RIGHT] button to select > privacy, selecting a screen part black not to be displayed a mask (AREA1 to AREA8) on the [MASK in the screen.
  • Page 34 Menu Operation NUMBER]. > Use the [LEFT],[RIGHT],[UP],[DOWN],[S ET] button to draw the polygon on the > Use [LEFT] or [RIGHT] button to set up the [POLYGON DRAW]. ON or OFF on the CIR. DISPLAY option. > Use the [LEFT],[RIGHT],[UP],[DOWN],[SET] > Use [UP] or [DOWN] to select an option button to move the polygon on the [POLYGON then use [LEFT] or [RIGHT] button to adjust...
  • Page 35: Special Menu Settings

    Menu Operation Special Menu Settings This menu lets you adjust and set up D-ZOOM, D-EFFECT, SHARPNESS, COLOR, STABILIZER, SYNC, USER TITLE, LANGUAGE function by yourself in the SPECIAL menu. Select [D-ZOOM] option on the [SPECIAL] menu. Use [LEFT] or [RIGHT] button to select a [ON] then press [SET] the DIGITAL ZOOM menu appears.
  • Page 36 Menu Operation Setting the D-EFFECT (Digital effect) Setting the SHARPNESS effect You can select the digital effect. The degree to which the boundary of the two portions is clearly distinguished. Select [D-EFFECT] option on the [SPECIAL] menu. Select [SHARPNESS] option on the [SPECIAL] menu. Use [LEFT] or [RIGHT] button to select a digital effect.
  • Page 37 Menu Operation Setting the COLOR effect STABILIZER setting You can switch the displayed picture to gray scale or color. The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration. This function is useful for outdoor surveillance. Select [STABILIZER] option and set to ON or OFF.
  • Page 38 Menu Operation Setting the SYNC (Synchronization) The SYNC function is available only with AC power source. Select [SYNC] option on the [SPECIAL] menu. Use [LEFT] or [RIGHT] button to select [INT] or [LL] (Line Lock). • INT: Selects for using the internal synchronization. 2-1.
  • Page 39 Menu Operation Setting the USER TITLE • A (Blank): Inserts a space at the cursor position. • : Moves cursor to left or right. You can use the camera identification to assign a number and character to the camera (0 to 9, A to Z, a to z). The USER TITLE is displayed on the upper left of the screen.
  • Page 40: Reset Settings

    Menu Operation Reset Settings • CAMERA REBOOT: To reboot the camera system. • FACTORY RESET: To reset the camera setting to factory setting, select [FACTORY RESET] option. Press [SET] button to confirm your selection. Select [RESET] option. Press [SET] button and the RESET menu appears. Use [UP] or [DOWN] to select option.
  • Page 41: Reference

    Reference RS-485 Protocol (Optional) ex) In case of transmission, 0xC5, 0x5F, 0x02, 0x00, 0x0A” Data Communication Format C.S. = 0xC5 +0x5F +0x02 +0x00 +0x0A = 0x0130 • Data Length: 1 Byte (8 Bit) therefore, C.S. = 0x30 • Start/Stop Bit: 1 Bit Commands •...
  • Page 42: Specification

    Reference Specification ITEM L332-BN L332-BP L332-CP Signal System NTSC Total Pixels No./ Effective Pixels No. 1028 x 508 / 976 x 494 1028 x 596 / 976 x 582 Image Device 6 mm CCD XDI-II Lens CS Mount (C Mount using adaptor ring)
  • Page 43 Reference ITEM L332-BN L332-BP L332-CP Motion detection SMART MD/REGIONAL MD/TAMPERING MD 3D-DNR OFF / LOW / MIDDLE / HIGH Auto Gain Control OFF / LOW / MIDDLE / HIGH Electronic Shutter Speed 1/60 to 1/120 000 1/50 to 1/120 000...

This manual is also suitable for:

L332-cpL332-bp