Download Print this page

Oasis SV104 Instruction Manual

Sv100 series actuated sandwich valve

Advertisement

Quick Links

SV100 Series
Actuated Sandwich Valve
Instruction Manual
Failure to follow these instructions or to properly install and maintain this equipment could result in gas leak-
age, fire or explosion causing property damage and personal injury or death.
Oasis products must be installed, operated and maintained by trained and competent personnel in
accordance with all applicable local codes, rules and regulations in addition to the Oasis Instructions.
Oasis Engineering Ltd. will not be held liable in such circumstances where installation, operation and
maintenance procedures were performed by incompetent personnel resulting in improper assembly, unsafe
operation, equipment damage or personal injury.
Oasis Engineering Ltd
129 Birch Avenue, Tauranga, New Zealand.
T: +64 7 928 3808 F: +64 7 928 3809
E: info@oasisNGV.com
W: www.OasisNGV.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the SV104 and is the answer not in the manual?

Questions and answers

Summary of Contents for Oasis SV104

  • Page 1 Oasis products must be installed, operated and maintained by trained and competent personnel in accordance with all applicable local codes, rules and regulations in addition to the Oasis Instructions. Oasis Engineering Ltd. will not be held liable in such circumstances where installation, operation and maintenance procedures were performed by incompetent personnel resulting in improper assembly, unsafe operation, equipment damage or personal injury.
  • Page 2 High pressure gas and gas equipment can cause serious harm to both infrastructure and personnel if safety precautions are not followed. Oasis recommends considering the use of the following PPE when working with high pressure along with any other site specific health and safety requirements:...
  • Page 3: Installation Instructions

    Installation Instructions Important Oasis recommends the use of class 12.9 plain black socket head cap screws with this product. Some surface corrosion is normal on plain black cap screws over time. The use of zinc plated cap screws is NOT recommended by...
  • Page 4 SV104= 26 Nm SV106= 60 Nm SV108= 70 Nm Without anti-seize: SV103= 37 Nm SV104= 37 Nm SV106= 60 Nm SV108= 70 Nm We reserve the right to modify product specifications without prior notice. SV-INS-02 3317 © Oasis Engineering Limited...
  • Page 5 8. Install actuator and bracket. 10. Tighten bracket screws. 9. Insert bracket screws. 11. Install complete, check for leaks on first use with snoop or soapy water. SV-INS-02 3317 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice.
  • Page 6 Do not operate the actuator with supply pressure greater than 8 Bar (116 psi). Doing so may damage the actuator and void the warranty. We reserve the right to modify product specifications without prior notice. SV-INS-02 3317 © Oasis Engineering Limited...
  • Page 7: Servicing Instructions

    * only used when servicing actuated ball valves. ** It is normal for the service kit to include a ball with a small hole in the bottom The Complete Oasis Seal Kit must be used Hex End Cap Sizes (A/F) Stem Nuts Sizes (A/F)
  • Page 8 Part Number: TOOL-SV106 TOOL-SV108 (Sold Separately) SV106 / SV108 SV103 / SV104 5. Discard the seat. 6. Discard the ball. Do not scratch body We reserve the right to modify product specifications without prior notice. SV-INS-02 3317 © Oasis Engineering Limited...
  • Page 9 Servicing - Disassembly SV103 SV104 - SV106 - SV108 7. Remove 2nd seat and discard. 7. Remove stem. Do not scratch body 8. Remove stem and discard. 8. Remove 2nd seat and discard. Do not scratch body 9. Clean components and inspect for damage.
  • Page 10 Servicing - Assembly SV104 - SV106 - SV108 SV103 1. Insert stem assembly first. 1. Insert seat first. Click 2. Insert seat. 2. Insert stem assembly. Click 3. Insert ball. We reserve the right to modify product specifications without prior notice.
  • Page 11 6. Tighten end cap. Allen Key Socket Adapter Part Number: Recommended TOOL-SV106 TOOL-SV108 End Cap Torques: (Sold Separately) SV103=35Nm SV104=60Nm Recommended End Cap Torques: SV106=120Nm SV108=120Nm SV-INS-02 3317 © Oasis Engineering Limited We reserve the right to modify product specifications without prior notice.
  • Page 12 12. Done! Follow installation instructions on page 3 to refit sandwich valve. (SV103 - 022 Nitrile 90) (SV104 - 025 Nitrile 90) (SV106 - 131 Nitrile 90) (SV108 - 138 Nitrile 90) We reserve the right to modify product specifications without prior notice.

This manual is also suitable for:

Sv103Sv106Sv108