Related Manuals for Nilfisk-Advance Whirlamatic 17UHS
Summary of Contents for Nilfisk-Advance Whirlamatic 17UHS
- Page 1 ™ Whirlamatic 17/20UHS OPERATOR MANUAL Advance MODELS 56183100, 56183105(OBS) 56183700, 56183701(OBS), 56183705 revised 4/01 FORM NO. 56041233...
-
Page 2: Table Of Contents
TABLE OF CONTENTS PAGE INTRODUCTION ..............2 IMPORTANT SAFETY INSTRUCTIONS ......... 3 IMPORTANT SAFETY INSTRUCTIONS ......... 4 GROUNDING INSTRUCTIONS ..........5 PREPARING THE FLOOR ............6 PREPARING THE MACHINE FOR USE........6 OPERATING CONTROLS ............7 OPERATING THE MACHINE........... 8 AFTER USING MACHINE ............ -
Page 3: Introduction
INTRODUCTION This manual will help you get the most from your Advance Whirlamatic. Read it thoroughly before operating the machine. References to “right” and “left” in this manual mean right or left as seen from the operator’s position. This product is intended for commercial use only. PARTS AND SERVICE Repairs, when required, should be performed by your Authorized Advance Service Center, who employs factory trained service personnel, and maintains an inventory of Advance original replacement parts and accessories. -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: Read all instructions before using. WARNING! To reduce risk of fire, electric shock, or injury: Do not leave the appliance when it is plugged in. Unplug the unit from the outlet when not in use and before servicing. To avoid electric shock, do not expose to rain. -
Page 5: Important Safety Instructions
IMPORTANTES MESURES DE SÉCURITÉ L’utilisation d’un appareil électrique demande certaines précautions: LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE FONCTIONNER (CET APPAREIL) AVERTISSEMENT: Pour réduire les risques d’incendie, de choc électrique ou de blessure: Ne pas laisser l’appareil sans surveillance lorsqu’il est branché. Débrancher lorsque l’appareil n’est pas utilisé et avant l’entretien. -
Page 6: Grounding Instructions
GROUNDING INSTRUCTIONS WARNING! This machine must be properly grounded to protect the operator from electrical shock. Read the safety instructions below before operating this machine. GROUNDED OUTLET BOX 120 volt machines have this kind of three-prong plug at the end of a three-wire electrical cord. The grounding pin on this plug grounds the machine when it is plugged into a three-prong 120 VOLT PLUG... -
Page 7: Preparing The Floor
PREPARING THE FLOOR Before each use of this machine, the floor must be clean and completely dry. Clean the floor with an automatic floor scrubber or a damp mop, using a solution of water and neutral cleaner. CAUTION! This machine should be used only on floors that are coated with a floor finish suitable for burnishing. Contact your local Advance Distributor for further information on floor finishing products. -
Page 8: Operating Controls
OPERATING CONTROLS Handle Twist Grip Lock Button Twist Grips Power Cord Handle Release Lever Whirlamatic Operator Manual - 7... -
Page 9: Operating The Machine
OPERATING THE MACHINE Plug the Power Cord (4) into a properly grounded electrical outlet. Pull the Handle Release Lever (5) UP and lower the Handle (1) to a comfortable operating position. It is normal for the base of the machine to lift off of the floor slightly when the handle is lowered. It will pull itself down against the floor as soon as the motor is started. -
Page 10: Maintenance
MAINTENANCE AIR FILTER The air filter on top of the motor must be cleaned once a month. To clean the filter, remove the 3 screws from the motor cover, lift the cover off and remove the filter from its holder. Wash the filter with warm water and allow it to dry completely before putting it back on the machine. -
Page 11: Troubleshooting
TROUBLESHOOTING MACHINE VIBRATES Pad not centered. Remove the pad, center and reinstall. Pad defective - Replace. SWIRL MARKS Pad or brush too aggressive for the floor finish. Dirty pad or brush. Check, clean or replace. RED LIGHT GLOWS Worn motor brushes. Have motor brushes replaced by local Advance Distributor. 10 - Whirlamatic Operator Manual... - Page 12 Nilfisk-Advance, Inc. 14600 21st Avenue North Plymouth, MN, 55447-3408 www.nilfisk-advance.com Phone: 800-989-2235 Fax: 800-989-6566 ©2000 Nilfisk-Advance, Inc., Plymouth, MN 55447-3408 Printed in the U.S.A.