System Settings - Roland DJ-505 Owner's Manual

System Settings

1
While holding down the [LOAD] button in the right side (R channel) of the browser section, and press the [POWER] switch to turn on the
power.
The DJ-505 is in system setting mode, and the [START/STOP] button of the TR-S section is blinking.
2
Press the TR-S pad or button that corresponds with the setting you want to make.
The display shows the current value.
3
Use the [VALUE] knob to change the value of the setting.
4
When you've finished making settings, press the blinking [START/STOP] button.
After a few seconds, the display shows "CONp. "
5
Turn the DJ-505's power off and then on again.
TR-S Pad Item
[1] Mic audio low cut filter setting
[2] Mic audio noise gate setting
[3] Mic input effect selection
[4] Mic input effect setting
[5] BOOTH OUT jack setting
[6] DVS input selection
[7] EQ ([HI]/[MID]/[LOW] knobs) maximum value
[8] Master output attenuator level
[9] BOOTH OUT attenuator level
[10] Cross fader curve
[11] Margin at both ends of cross fader
[12] Performance pad velocity curve
[13] TR-S section knob mode
[14] Demo mode time setting
[15] LED brightness adjustment
[16] Auto Off function (p. 10) setting
Value (Bold: default) Explanation
Adjusts the strength of the low cut filter applied to the mic audio.
1–10
OFF , 1 – 10
OFF
Specifies the strength of the noise gate applied to the mic audio.
1–10
OFF , 1 – 10
OFF
Specifies the effect that is applied to the mic audio.
Reverb
Delay
OFF , (Reverb), dLy (Delay),
Delay +
(Delay + Reverb)
Reverb
OFF
Adjusts the depth of the effect that is applied to the mic audio.
OFF , 1 – 4 – 10 1–10
OFF
Specifies whether the mic audio is output (On) or is not output (OFF) from the BOOTH OUT jacks.
On , OFF
Selects the input signal when using DVS.
Phono
PHOn (PHONO), Line (LINE),
Line
(AUX)
Aux
Specifies the maximum value of the equalizer.
When the [HI]/[MID]/[LOW] knobs of each channel are turned all the way to the right, they have the
3db , 6db
value specified here.
* This setting is effective only in stand-alone mode.
Specifies the attenuation level of the master output. The master output level decreases by the
0 , -3 , -6 , -12 , -18 (dB)
amount of this value.
Specifies the attenuation level of the booth output. The booth output level decreases by the
0 , -3 , -6 , -12 , -18 (dB)
amount of this value.
Specifies the curve of the cross fader.
Level
Line (Linear), poU - (Power)
* This setting is effective only in stand-alone mode.
Specifies the margin at both ends of the cross fader. Higher values increase the margin, providing
0 , 1 – 10
more play at each end of the cross fader.
Specifies the velocity curve of the performance pads (the way in which the level changes in
response to the strength of your strike on the pad).
LoU - (Low), Nid (Mid), Hi (Hi) Level
Specifies how the knobs in the TR-S section operate.
Picc W (Pick), JUNP (Jump) Pick
Jump
Specifies the time (minutes) from when the DJ-505 was last operated until it enters demo mode.
OFF , 1 – 10 – 30
If this is OFF, demo mode will not operate.
Adjusts the brightness when a button, pad, or indicator is lit.
0 – 3
Higher values decrease the brightness.
When no operation has been performed for a certain length of time, the power turns off
On , OFF
automatically. If you don't want the power to turn off automatically, set this "OFF. "
Higher values produce a stronger effect.
The low cut filter is not applied.
As the value increases, even higher-level sound will be cut.
The noise gate is not applied.
Reverb is applied.
Delay is applied.
Delay and reverb are applied simultaneously.
No effect is applied.
Higher values apply the effect more deeply.
No effect is applied.
The phono-level (a connected turntable without an EQ amp) input is the source.
The line-level (a connected DJ player or turntable with an EQ amp) is the source.
DVS is not used; rather, the input to the INPUT (CH 1, CH 2) jacks is used as the AUX
signal.
Linear Power
high
low
center left/right
Position of fader
Low Mid
high
low
weak strong
Strength of pad strike
If there is a discrepancy between the recalled value and the position of the knob, data
is output only after you turn the knob to the position that matches the value.
Data is always output according to the position of the knob.
Hi
21