Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HDTV Supply HDTV88CAT
Summary of Contents for HDTV Supply HDTV88CAT
- Page 1 8x8 HDMI Matrix with Simultaneous CAT and HDMI Outputs Operation Manual VER:1.2...
-
Page 2: Package Contents
User Manual 1. Introduction The 8x8 HDMI Matrix with simultaneous CAT and HDMI outputs connects eight HDMI sources to ten displays. The matrix features eight CAT -Cable outputs and output 7&8 are mirrored to provide a HDMI output which runs simultaneously . Connect a SINGEL UTP Receiver to each of the CAT -Cable outputs to extend the HDMI signal up to 164ft/50m for multi-room connectivity. -
Page 3: Specifications
User Manual Wideband IR Tx cable 8pcs Wideband IR Rx cable 9pcs HDMI Matrix IR Remote 1pcs Mounting ears(Matrix) 2pcs Mounting ears(Receiver) 16pc RS232 cable 1pcs 4. Specifications Video Bandwidth 165 MHz Support Video Resolution 480i,576i,480p,576p,720p,1080i, 1080p24/30/50/60. Input Ports 8×HDMI, 8×IR Extender, 1×RS -232, 1×RJ-45(Control) , 1xMatrix IR Extender Output Ports 8×CAT, 8×IR Extender, 2×HDMI , 8×Audio... -
Page 4: Panel Functions
User Manual 5. PANELFUNCTIONS 5.1 Front Panel OUTPUT EDID A LL M EN U O U T P U T : A B C D E F G H MATRIX 8X8 I N P U T : 1 2 3 4 56 7 8 EN TER D O W N INPUT... - Page 5 User Manual ※ Note:The EDID mode table EDID Mode EDID Description 1080 i, 2CH AUDIO 1080 i, DOLBY/DTS 5.1 1080 i, HD AUDIO 1080 p, 2CH AUDIO 1080 p, DOLBY/DTS 5.1 1080 p, HD AUDIO 3D,1080p, 2CH AUDIO 3D, 1080p,DOLBY/DTS 5.1 3D,1080p, HD AUDIO 4k x 2k , 2CH AUDIO 4k x 2k , DOLBY/DTS 5.1...
- Page 6 User Manual Why is EDID so important with theHDMI Matrix? The Matrix is complex piece of technology that replicates and switches between multiple inputs and outputs. Each connected source device will require one EDID to read. EDID management is carefully handled by HDMI Matrix to provide a single EDID for each source to read.
-
Page 7: Hdmi Input
User Manual 2. Audio out 1) Analog audio output, Audio Extraction from HDMI input signal and support PCM 44.1K,48K,96K 3. IR Channel IR EXT: if the panel sensor is obstructed or the unit is installed in a closed area out of infrared line of sight, the IR RX receiver included can be inserted into the IR EXT port at the rear to extend the IR sensor range and enable local control of the matrix. - Page 8 User Manual 2. How to select Output and Input Port? Q. OUTPUT-X select INPUT-Y: A. Press OUTPUT-X (X means 1 to 8 of outputs, including ALL)Press INPUT-Y (Y means 1 to 8 of inputs) 7. Super IR Control system (IR Call-back of Matrix and Source Devices) The matrix is not only a switcher and extender of multiple HDMI signals to multiple HDMI receivers located...
- Page 9 User Manual 1. At Matrix end: Insert the 3.5mm jacks of the IR TX Emitters included with the unit into the IR TX Emitter ports at the rear of the matrix according to input. The IR signal is added to the HDMI of the input device so, for example, if the user is watching Blu-ray on input 1, the IR signal will be directed through the IR TX1 socket to control the device.
- Page 10 User Manual receivers fully powered and the matrix set to IR call-back enabled and IR TX Swicth mode activated, two -way IR will now be possible. Note: Misplaced or poorly secured IR Emitters and Receivers may result in intermittent IR control signals passed to and from the matrix. Check your placement and adjust if necessary.
-
Page 11: Audio Return Channel (Arc)
User Manual 1. HDMI OUT: This slot is where you connect the HDTV or monitor with HDMI cable for input source display. 2. LOCK LED: This blue LED illuminate when the signal locked. 3. POWER LED: This blue LED illuminate when the device is connected with power supply. -
Page 12: Installation
User Manual IR RECEIVER IR RLASTER 9. PC controller user guide Installation Matrix controller is a green software. Just copy MatrixController.exe to PC which is used to control the Matrix by RS232 COM port or TCP/IP to complete installation. Preparation Connect PC and Matrix by RS232 cable (headers of both sides of cable should be FEMALE) or TCP/IP(local area network) Power-up Matrix... - Page 13 User Manual How to control Matrix “General” page 1. Select RS232 COM or TCP mode 2. Select RS232 COM port 3. Click to connect or disconnect PC and Matrix 4. Select Matrix IP 5. Connect to Matrix IP 6. Search Matrix IP 7.
- Page 14 User Manual 10. Click to refresh device status: include device information displayed in 9 area and Input/Output Settings on “Matrix” page 11. Click to clear device information 12. Enable or disable Beep Configure TCP After action of 7, edit form will pop-up as below: 1.
- Page 15 User Manual The controller have 3 methods to set the EDID mode. Manual mode, Copy mode and open EDID file mode. 1. Select the needed EDID to input port and click set button the EDID will write to the selected HDMI input ports. 2.
- Page 16 User Manual “FW upgrade” page 1. Click to open FW file(file extension is “.fw”) 2. Display the FW file path 3. Displaying the progress of the software upgrade 4. Click to upgrade the Matrix software 5. Display the message of the software upgrade 6.
- Page 17 User Manual 1. Connect up to 8 sources such as a Blu-Ray Player, game console, A/V Receiver, Cable or Satellite Receiver, etc. to the HDMI inputs on the unit. Do not hotplug! Insert and extract cables carefully with the power SWITCHED OFF.