Table of Contents
Advertisement
Quick Links
Active Control Monitor
KLEIN + HUMMEL GmbH
Zeppelinstrasse 12 • 73760 Ostfildern/Germany
Active Control Monitor
KLEIN + HUMMEL GmbH
Zeppelinstrasse 12 • 73760 Ostfildern/Germany
M 51 D
Installation
Operation
0 5 8 - E 0 0 0 8
Version 04/05
Tel.: + 49/(0)711/ 45893 - 0
Fax: + 49/(0)711/ 45893 - 35
eMail: info@klein-hummel.de
Internet: www.klein-hummel.com
M 51 D
Installation
Operation
0 5 8 - E 0 0 0 8
Version 04/05
Tel.: + 49/(0)711/ 45893 - 0
Fax: + 49/(0)711/ 45893 - 35
eMail: info@klein-hummel.de
Internet: www.klein-hummel.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Klein + Hummel M 51 D
Summary of Contents for Klein + Hummel M 51 D
- Page 1 Active Control Monitor M 51 D Installation Operation 0 5 8 - E 0 0 0 8 Version 04/05 KLEIN + HUMMEL GmbH Tel.: + 49/(0)711/ 45893 - 0 Fax: + 49/(0)711/ 45893 - 35 eMail: info@klein-hummel.de Zeppelinstrasse 12 • 73760 Ostfildern/Germany Internet: www.klein-hummel.com...
-
Page 2: Safety Instructions
1. Safety Instructions € Loudspeaker output jacks labeled with the IEC 417/5036 emblem (Fig. A, right) may be carrying dangerously high It is absolutely essential that you read these safety voltages. If your unit has this emblem, ensure that any instructions carefully before connecting and using this connections to be made between these jacks and the K+H product. - Page 3 € Always check before connecting the power cable to the Do not block or cover any heat sink, fan, or vent. mains socket that the power switch on the unit itself is set € Do not place the product where it will be in the path of to off ("O").
-
Page 4: Installation
2.2 Operating conditions as seen from the solder terminals of male XLR The K+H model M 51 D active control monitor is intended for use over a range of ambient temperatures from +10° C to +40° C (+50° F to +104° F). During transport or storage, temperatures from -25°... - Page 5 S/P-DIF or AES 3id format. The incoming digital signal line requires one 75-Ohm terminator at the very end, as the M 51 D has no internal termination. The XLR input and the BNC input are wired in parallel across a transformer.
-
Page 6: Speaker Placement
Stereo pairs should be turned to the hearing area. On the bottom there is a 3/8" threaded bushing for mounting the M 51 D on a standard microphone tripod. The LH 11 table mount bracket can be fixed to the two M6 threaded holes in the sides and so allows rotation around horizontal and verti- kal axis. -
Page 7: Warranty
The M 51 D is designed for nearfield monitoring. For best In the event warranty service is required, presentation of a performance and reliability it is recommended to avoid warranty card will not be necessary. -
Page 8: Specifications
Specifications M 51 D Analog - digital converter Free-field frequency response 110 Hz - 20 kHz ± 5 dB Self generated noise @ 10 cm 20 dB (A) Resolution, type 24 Bit DA, delta sigma Total harmonic distortion Sampling rate...
Need help?
Do you have a question about the M 51 D and is the answer not in the manual?
Questions and answers