Page 1 2 0 1 8 P R O M A S T E R O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name features and equipment that are either standard or op- FCA US LLC shall be deemed to be deleted and the name tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Table Of Contents
INTRODUCTION CONTENTS INTRODUCTION ......4 WARNINGS AND CAUTIONS ....6 HOW TO USE THIS MANUAL .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION versions are not expressly indicated in the text. Therefore, you should only consider the information which is related Dear Customer, to the trim level, engine, and version that you have Congratulations on selecting your new vehicle. Be assured purchased.
Page 7: Symbols
INTRODUCTION 5 Symbols Since the specification of your vehicle depends on the items of equipment ordered, certain descriptions and illustra- Consult the following table for a description of the symbols tions may differ from your vehicle’s equipment. that may be used on your vehicle or throughout this The detailed index at the back of this Owner’s Manual Owner’s Manual: contains a complete listing of all subjects.
Page 8: Warnings And Cautions
6 INTRODUCTION WARNINGS AND CAUTIONS Operating instructions for the special equipment installed by the conversion/camper manufacturer should also be This Owner’s Manual contains WARNINGS against oper- supplied with your vehicle. If these instructions are miss- ating procedures that could result in a collision, bodily ing, please contact your authorized dealer for assistance in injury and/or death.
Page 9 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......8 INTERIOR ......11 REAR VIEW .
Page 10 8 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Hood/Engine Compartment 4 — Wheels/Tires 2 — Windshield 5 — Exterior Mirrors 3 — Headlights 6 — Doors...
Page 11 GRAPHICAL TABLE OF CONTENTS 9 REAR VIEW Rear View 1 — Rear Lights 2 — Cargo Area Doors...
Page 12 10 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 4 — Windshield Wiper Lever 2 — Multifunction Lever 5 — Radio 3 — Instrument Cluster 6 — Steering Wheel...
Page 13 GRAPHICAL TABLE OF CONTENTS 11 INTERIOR Interior 1 — Door Locks/Window Switches 4 — Switch Panel 2 — Seats 5 — Climate Controls 3 — Gear Selector 6 — Glove Compartment...
Page 15 GETTING TO KNOW YOUR VEHICLE CONTENTS KEYS ....... . .16 ▫...
Page 16 14 GETTING TO KNOW YOUR VEHICLE ▫ Inside Day/Night Mirror — If Equipped ..34 INTERIOR LIGHTS ..... . .41 ▫...
Page 17 GETTING TO KNOW YOUR VEHICLE 15 INTERNAL EQUIPMENT ....58 ▫ Power Outlets ......61 ▫...
Page 18: Keys
16 GETTING TO KNOW YOUR VEHICLE KEYS Key Fob Your vehicle uses a key start ignition system. The ignition system consists of a key fob with a Remote Keyless Entry (RKE) and an ignition switch. The key fob contains an integrated mechanical key. To use the mechanical key, simply push the mechanical key re- lease button.
Page 19 GETTING TO KNOW YOUR VEHICLE 17 If a door is open, the turn signal lights will flash at an increased rate, and there will be no horn chirp. This is to indicate that a door is still open. Locking Doors With A Key 1.
Page 20: Ignition Switch
18 GETTING TO KNOW YOUR VEHICLE General Information The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1.
Page 21 GETTING TO KNOW YOUR VEHICLE 19 WARNING! (Continued) from vehicle, and lock all doors. and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Leaving children in a vehicle unattended is dangerous for a number of reasons.
Page 22: Key-In-Ignition Reminder
20 GETTING TO KNOW YOUR VEHICLE If the vehicle security light is on after the key is turned to CAUTION! the ON/RUN position, it indicates that there is a problem with the electronics. An unlocked vehicle is an invitation. Always remove the key from the ignition and lock all the doors when CAUTION! leaving the vehicle unattended.
Page 23: General Information
GETTING TO KNOW YOUR VEHICLE 21 General Information To Arm The System The following regulatory statement applies to all radio To arm the system, the vehicle security alarm will set when frequency (RF) devices equipped in this vehicle: you use the key fob to lock the doors. If a door or the hood is not properly shut, the alarm system will not be armed.
Page 24: Security System Manual Override
22 GETTING TO KNOW YOUR VEHICLE alarm is still present, the system will ignore that condition The load compartment power door lock switch is located and monitor the remaining doors and ignition. on the driver door trim panel. Use this switch to lock or unlock the load compartment doors.
Page 25: Auto Unlock Doors
GETTING TO KNOW YOUR VEHICLE 23 WARNING! (Continued) CAUTION! • For personal security and safety in the event of a An unlocked vehicle is an invitation. Always remove collision, lock the vehicle doors as you drive as well the key from the ignition and lock all of the doors as when you park and leave the vehicle.
Page 26: Manual Adjustments
24 GETTING TO KNOW YOUR VEHICLE Forward And Rearward Adjustment WARNING! The adjusting bar is at the front of the seat, near the floor. • It is dangerous to ride in a cargo area, inside or outside Pull the bar upward to move the seat forward or rearward. of a vehicle.
Page 27 GETTING TO KNOW YOUR VEHICLE 25 Height Adjustment Without Swivel Seat The height adjusting levers are located on the center outboard side of the seat. Lift up on the front lever to adjust the front of the seat, or lift up on the rear lever to adjust the rear of the seat.
Page 28 26 GETTING TO KNOW YOUR VEHICLE With Swivel Seat Recliner Adjustment Without Swivel Seat The height adjusting knobs are located on the center outboard side of the seat. Rotate the front knob to adjust The recliner knob is on the rear outboard side of the seat. To the front of the seat up or down.
Page 29 GETTING TO KNOW YOUR VEHICLE 27 With Swivel Seat WARNING! The recliner lever is located at the lower front outboard • Adjusting a seat while the vehicle is moving is side of the seat. To recline the seatback, lean forward dangerous.
Page 30 28 GETTING TO KNOW YOUR VEHICLE Damper Weight Adjustment position or at the 180° position. To swivel the seat, pull the swivel seat inboard lever outward, turn the seat to the Use the weight adjustment knob to set the required setting desired position and release the lever.
Page 31: Heated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 29 Heated Seats — If Equipped the right position and the first vehicle movement after the cranking is attempted, a chime and a text message will On some models, the front driver and passenger seats may appear in instrument cluster display.
Page 32: Fold Down Tray - If Equipped
30 GETTING TO KNOW YOUR VEHICLE Fold Down Tray — If Equipped WARNING! If your vehicle is equipped with a bench seat, the seat is • Persons who are unable to feel pain to the skin equipped with a fold-down tray that can be used as a because of advanced age, chronic illness, diabetes, document support surface.
Page 33: Adjustable Armrests - If Equipped
GETTING TO KNOW YOUR VEHICLE 31 Adjustable Armrests — If Equipped The fold-down tray is equipped with two cup holders and a support surface with a paper holder clip. The seat adjustable armrest can be raised and adjusted for height. Underneath the front of the armrest is the adjuster wheel which will adjust the height of the armrest up or down.
Page 34: Head Restraints
32 GETTING TO KNOW YOUR VEHICLE Turn the adjuster wheel to the right or left to adjust the WARNING! height of the armrest up or down. • All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of a crash.
Page 35: Front Head Restraint Removal
GETTING TO KNOW YOUR VEHICLE 33 reinstall the head restraint, put the head restraint posts into the holes. Then, adjust it to the appropriate height. NOTE: Do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head.
Page 36: Mirrors
34 GETTING TO KNOW YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death.
Page 37: Outside Mirrors
GETTING TO KNOW YOUR VEHICLE 35 WARNING! Vehicles and other objects seen in an outside convex mirror will look smaller and farther away than they really are. Relying too much on side convex mirrors could cause you to collide with another vehicle or other object.
Page 38: Power Folding Mirrors - If Equipped
36 GETTING TO KNOW YOUR VEHICLE Power Folding Mirrors — If Equipped The switch for the power folding mirrors is located on the driver’s door panel below the power mirror controls. Power Mirror Controls To adjust a mirror, turn the control knob toward the left upper, left lower, right upper or right lower mirror posi- tions indicated by one of the four arrow’s on the switch.
Page 39 GETTING TO KNOW YOUR VEHICLE 37 The power folding mirrors are designed to be folded and unfolded using the power folding switch. If the mirrors are manually folded, the mirror head may appear loose. If the mirror head or pivot exhibits a slight amount of play, the mirror should be power folded closed, then power folded open (this may require multiple button pushes).
Page 40: Heated Mirrors - If Equipped
38 GETTING TO KNOW YOUR VEHICLE Forward Folding CAUTION! Mirrors can be folded forward manually or by accidental Leaving the mirror in a non powered position, acciden- impact. In this case it is possible to restore to position both tal impact or manual fold, may cause permanent dam- ways, manually and electrically (as described above).
Page 41: Headlights
GETTING TO KNOW YOUR VEHICLE 39 Daytime Running Lights — If Equipped NOTE: When the headlights are turned on, the Daytime Running Lights will be deactivated. To activate the Daytime Running Lights (DRL), rotate the end of the multifunction lever to the O (Off) position. NOTE: The low beams and side/taillights will not be on with DRL.
Page 42: Flash-To-Pass
40 GETTING TO KNOW YOUR VEHICLE Flash-To-Pass pulled, the activation of the lights will be extended by 30 seconds. The activation of the lights can be extended to a You can signal another vehicle with your headlights by maximum of 210 seconds. partially pulling the multifunction lever toward the steer- ing wheel.
Page 43: Turn Signals
GETTING TO KNOW YOUR VEHICLE 41 Turn Signals INTERIOR LIGHTS Move the multifunction lever up or down and the arrows Courtesy Lights on each side of the instrument cluster flash to show proper These lights are mounted between the sun visors on the operation of the front and rear turn signal lights.
Page 44 42 GETTING TO KNOW YOUR VEHICLE Dome Lights Rear Lights The interior lights can be set to three different positions The Rear Cargo Lamp is located at the upper rear cargo (Off/Left Position, Center Position, On/Right Position). area above the rear doors. Using the switch on the bottom of the overhead console: •...
Page 45 GETTING TO KNOW YOUR VEHICLE 43 Dimmer Controls The dimmer controls are located on the left side of the instrument panel below the instrument cluster display. Side Cargo Lamp The Cargo Lamps can be set to three different positions (Off/Right Position, Center Position, On/Left Position). •...
Page 46: Illuminated Entry
44 GETTING TO KNOW YOUR VEHICLE Illuminated Entry NOTE: The windshield wipers/washers will only operate with the ignition in the ON/RUN position. The courtesy lights will turn on when you use the key fob or manually from the driver door cylinder to unlock the doors or open any door.
Page 47: Climate Controls
GETTING TO KNOW YOUR VEHICLE 45 High Speed Mist Feature Use the Mist feature when weather conditions make occa- Push the lever downward to the third detent. The wipers sional usage of the wipers necessary. Push the lever up- will operate at high speed. ward to the MIST position and release for a single wiping Windshield Washer Operation cycle.
Page 48: Manual Climate Control Overview
46 GETTING TO KNOW YOUR VEHICLE Manual Climate Control Overview The Manual Temperature Controls consist of a series of three outer rotary dials (blower speed, temperature and mode) and three inner push buttons (Recirculation, A/C, Rear Window Defroster). Manual Temperature Controls Manual Climate Control Descriptions Icon Description...
Page 49 GETTING TO KNOW YOUR VEHICLE 47 Icon Description Recirculation Button Press and release this button to change the system between recirculation mode and outside air mode. Recirculation can be used when outside conditions such as smoke, odors, dust, or high humidity are present.
Page 50 48 GETTING TO KNOW YOUR VEHICLE Icon Description Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. Rotat- ing the knob counterclockwise, from top center into the blue area of the scale, indicates cooler temperatures.
Page 51 GETTING TO KNOW YOUR VEHICLE 49 Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets.
Page 52: Climate Control Functions
50 GETTING TO KNOW YOUR VEHICLE Climate Control Functions Additional Rear Climate Control — If Equipped This switch, mounted on the instrument panel to the left of A/C (Air Conditioning) the steering column, activates the additional rear heating/ The Air Conditioning (A/C) button allows the operator to air conditioning system vent.
Page 53: Operating Tips
GETTING TO KNOW YOUR VEHICLE 51 interior air by pressing the Recirculation control button. MS.90032 and 50% water is recommended. Refer to “Dealer The recirculation indicator will illuminate when this button Service” in “Servicing And Maintenance” for proper cool- is selected. Press the button a second time to turn off the ant selection.
Page 54 52 GETTING TO KNOW YOUR VEHICLE NOTE: Recirculate without A/C should not be used for A/C Air Filter long periods, as fogging may occur. The climate control system filters outside air containing dust, pollen and some odors. Strong odors cannot be totally Outside Air Intake filtered out.
Page 55 GETTING TO KNOW YOUR VEHICLE 53 Control Setting Suggestions For Various Weather Conditions Control Settings Suggestions For Various Weather Conditions Chart...
Page 56: Windows
54 GETTING TO KNOW YOUR VEHICLE WINDOWS WARNING! Power Windows • Never leave children alone in a vehicle, or with The control on the left front door panel has up-down access to an unlocked vehicle. Allowing children to switches that give you fingertip control of all power be in a vehicle unattended is dangerous for a number windows.
Page 57: Window Bar Grates - If Equipped
GETTING TO KNOW YOUR VEHICLE 55 NOTE: The power window switches remain active for up WARNING! to three minutes (depending on the accessory delay set- ting) after the ignition switch has been turned OFF. Open- The metal grates over the sliding door windows are ing either of the vehicle’s front doors will cancel this designed to protect you in the event of an accident.
Page 58: Hood
56 GETTING TO KNOW YOUR VEHICLE HOOD 2. Move to the outside of the vehicle, reach into the opening beneath the center of the hood and push the Opening safety latch lever to the right to release it, before raising To open the hood, two latches must be released.
Page 59: Closing
GETTING TO KNOW YOUR VEHICLE 57 3. Raise the hood and place the hood prop rod in hood slot CAUTION! to secure the hood in the open position. To prevent possible damage: • Before closing hood, make sure the hood prop rod is fully seated into its storage retaining clips.
Page 60: Internal Equipment
58 GETTING TO KNOW YOUR VEHICLE INTERNAL EQUIPMENT Front Door Storage — If Equipped Storage areas and bottle holders are located in both the Storage front door trim panels. Glove Compartments The glove compartment is located on the passenger side of the instrument panel and features both an upper and lower storage area.
Page 61 GETTING TO KNOW YOUR VEHICLE 59 Dash Storage Dashboard Clipboard The dash storage is located on the right side of the Located on top of the dashboard is a clipboard and two instrument panel. storage bins on each side of the clipboard. Dash Storage Clipboard And Storage Bins...
Page 62: Cupholders
60 GETTING TO KNOW YOUR VEHICLE Cupholders Underseat Storage Tray (Driver Side Only) — If Equipped The cupholders for the driver’s and passenger’s area are A storage tray is located under the driver’s seat that can be located near the floor just under the center stack storage easily removed by withdrawing the hooks on the support compartment.
Page 63: Power Outlets
GETTING TO KNOW YOUR VEHICLE 61 Power Outlets Passenger Compartment Power Outlet The cigar lighter and the power outlet are located in the center console. It only operates with the ignition key at MAR/ON. Load Compartment Power Outlet NOTE: Do not connect devices with power higher than 180 W to the socket.
Page 64 62 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 65: Auxiliary Switches - If Equipped
GETTING TO KNOW YOUR VEHICLE 63 Auxiliary Switches — If Equipped Auxiliary Switch 1 is configured to constant battery feed, while Auxiliary Switch 2 is configured to ignition feed. Your vehicle may be equipped with two auxiliary switches located on the instrument panel to the left of the steering For further information on using the auxiliary switches, column which can be used to power various electronic please refer to the Ram Body Builders Guide by accessing...
Page 67 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT CLUSTER ....66 WARNING LIGHTS AND MESSAGES ..74 ▫...
Page 68: Instrument Cluster
66 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Instrument Cluster...
Page 69: Instrument Cluster Descriptions
GETTING TO KNOW YOUR INSTRUMENT PANEL 67 Instrument Cluster Descriptions • Gear Selector Status (PRND) The gear selector status “P,R,N,D,1,2,3,4,5,6” are dis- 1. Speedometer played indicating the gear selector position. Telltales • Indicates vehicle speed. “1,2,3,4,5,6” indicate the manual mode has been en- 2.
Page 70: Instrument Cluster Display
68 GETTING TO KNOW YOUR INSTRUMENT PANEL 5. Fuel Gauge WARNING! • The pointer shows the level of fuel in the fuel tank A hot engine cooling system is dangerous. You or when the ignition switch is in the ON/RUN position. others could be badly burned by steam or boiling •...
Page 71: Location And Controls
GETTING TO KNOW YOUR INSTRUMENT PANEL 69 Location And Controls • Service (Diesel Only) The instrument cluster display features a driver-interactive • Exit Menu display that is located in the instrument cluster. If equipped with a Uconnect system, some customer pro- grammable features will display in the radio.
Page 72: Change Engine Oil
70 GETTING TO KNOW YOUR INSTRUMENT PANEL • MODE Button change indicator system is duty cycle based, which means the engine oil change interval may fluctuate, dependent Push and hold the MODE button for a time longer than upon your personal driving style. one second to access/select the information screens or Unless reset, this message will continue to display each submenu screens of a main menu item.
Page 73 GETTING TO KNOW YOUR INSTRUMENT PANEL 71 The setup menu can be activated by pushing the MODE 2. Push and release the up or down arrow button (by button. Single pushes on the up or down arrow button will single pushes) to select the new setting. scroll through the setup menu options.
Page 74: Values Displayed
72 GETTING TO KNOW YOUR INSTRUMENT PANEL Values Displayed Current Fuel Consumption This indicates the fuel consumption. The value is con- Range stantly updated. The message “----” will appear on the This indicates the distance which may be traveled with the display if the vehicle is parked with the engine running.
Page 75: Trip Computer
GETTING TO KNOW YOUR INSTRUMENT PANEL 73 NOTE: New Trip • If equipped, some customer programmable features To reset: will display in the Uconnect system. Refer to • Push and hold the TRIP button to reset the system “Uconnect Settings” in “Multimedia” for further infor- manually.
Page 76: Trip Functions
74 GETTING TO KNOW YOUR INSTRUMENT PANEL WARNING LIGHTS AND MESSAGES 2. Briefly push and release the MENU button to go back to the menu screen or push and hold the MENU (approxi- Red Warning Lights mately one second) to go back to the main screen without storing settings.
Page 77 GETTING TO KNOW YOUR INSTRUMENT PANEL 75 — Electric Power Steering Fail Warning Light ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position. The This light will turn on when there’s a fault with the EPS light should turn off.
Page 78 76 GETTING TO KNOW YOUR INSTRUMENT PANEL — Engine Temperature Warning Light In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake This light warns of an overheated engine condition. If the booster, the ABS pump will run when applying the brake, engine coolant temperature is too high, this indicator will and a brake pedal pulsation may be felt during each stop.
Page 79: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 77 Vehicles equipped with the Anti-Lock Brake System (ABS) Do not operate the vehicle until the cause is corrected. This are also equipped with Electronic Brake Force Distribution light does not indicate how much oil is in the engine. The (EBD).
Page 80 78 GETTING TO KNOW YOUR INSTRUMENT PANEL can lead to tire failure. Under-inflation also reduces fuel CAUTION! efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Do not continue driving with one or more flat tires as handling may be compromised.
Page 81 GETTING TO KNOW YOUR INSTRUMENT PANEL 79 ensure that the replacement or alternate tires and wheels system. If this light remains on after several ignition cycles, allow the TPMS to continue to function properly. and the vehicle has been driven several miles (kilometers) at speeds greater than 30 mph (48 km/h), see your autho- CAUTION! rized dealer as soon as possible to have the problem...
Page 82 80 GETTING TO KNOW YOUR INSTRUMENT PANEL — Engine Check/Malfunction Indicator Warning WARNING! (Continued) Light (MIL) operating conditions. This can cause a fire if you drive The Engine Check/Malfunction Indicator Light (MIL) is a slowly or park over flammable substances such as dry part of an Onboard Diagnostic System called OBD II that plants, wood, cardboard, etc.
Page 83: Yellow Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 81 Yellow Indicator Lights If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not function- — Stop Light Failure Indicator Light ing and service is required. However, the conventional This light will illuminate if one or more of the stop light brake system will continue to operate normally if the brake bulb fails.
Page 84: Green Indicator Lights
82 GETTING TO KNOW YOUR INSTRUMENT PANEL The failure relating to these lights could be: — Park/Headlight On Indicator Light • One or more blown bulbs This indicator will illuminate when the park lights or headlights are turned on. • A blown protection fuse —...
Page 85: Onboard Diagnostic System (Obd Ii) Cybersecurity
GETTING TO KNOW YOUR INSTRUMENT PANEL 83 control systems. When these systems are operating prop- information related to the performance of your emissions erly, your vehicle will provide excellent performance and controls. Authorized service technicians may need to ac- fuel economy, as well as engine emissions well within cess this information to assist with the diagnosis and current government regulations.
Page 86: Emissions Inspection And Maintenance Programs
84 GETTING TO KNOW YOUR INSTRUMENT PANEL EMISSIONS INSPECTION AND MAINTENANCE NOTE: If you crank or start the engine, you will have to PROGRAMS start this test over. In some localities, it may be a legal requirement to pass an 2.
Page 87 GETTING TO KNOW YOUR INSTRUMENT PANEL 85 If your OBD II system is not ready, you should see your authorized dealer or repair facility. If your vehicle was recently serviced or had a battery failure or replacement, you may need to do nothing more than drive your vehicle as you normally would in order for your OBD II system to update.
Page 89 SAFETY CONTENTS SAFETY FEATURES ..... . .88 ▫ Child Restraints ..... . .123 ▫...
Page 90: Safety Features
88 SAFETY SAFETY FEATURES WARNING! (Continued) Four-Wheel Anti-Lock Brake System (ABS) by improperly installed or high output radio trans- mitting equipment. This interference can cause pos- The Four-Wheel ABS is designed to aid the driver in sible loss of anti-lock braking capability. Installation maintaining vehicle control under adverse braking condi- of such equipment should be performed by qualified tions.
Page 91: Electronic Brake Control System
SAFETY When you are in a severe braking condition involving the slip differential and controls the wheel spin across a driven use of the ABS, you will experience some pedal drop as the axle. If one wheel on a driven axle is spinning faster than vehicle comes to a stop.
Page 92 90 SAFETY WARNING! (Continued) WARNING! • The capabilities of a TCS-equipped vehicle must The Brake Assist System (BAS) cannot prevent the never be exploited in a reckless or dangerous man- natural laws of physics from acting on the vehicle, nor ner, which could jeopardize the user’s safety or the can it increase the traction afforded by prevailing road safety of others.
Page 93 SAFETY the intended path, ESC applies the brake of the appropriate WARNING! (Continued) wheel to assist in counteracting the oversteer or understeer • Vehicle modifications, or failure to properly main- condition. tain your vehicle, may change the handling charac- • Oversteer - when the vehicle is turning more than teristics of your vehicle, and may negatively affect appropriate for the steering wheel position.
Page 94 92 SAFETY will be in this mode. This mode should be used for most WARNING! (Continued) driving situations. ESC should only be turned off for “Partial Off” mode, the engine power reduction specific reasons as noted below. feature of TCS is disabled, and the enhanced vehicle ESC Partial Off stability offered by the ESC system is reduced.
Page 95 SAFETY detected in the ESC system. If this light remains on after • The ESC system will make buzzing or clicking sounds several ignition cycles, and the vehicle has been driven when it is active. This is normal; the sounds will stop several miles (kilometers) at speeds greater than 30 mph when ESC becomes inactive following the maneuver (48 km/h), see your authorized dealer as soon as possible...
Page 96 94 SAFETY to individual wheels to attempt to stop the trailer from WARNING! swaying. TSC is disabled when the ESC system is in the “Partial Off” mode. • If you use a trailer brake controller with your trailer, the trailer brakes may be activated and deactivated WARNING! with the brake switch.
Page 97: Auxiliary Driving Systems
SAFETY • Gear selection matches vehicle uphill direction (i.e., outside temperature decreases, the tire pressure will de- vehicle facing uphill is in forward gear; vehicle backing crease. Tire pressure should always be set based on cold uphill is in REVERSE gear). inflation tire pressure.
Page 98 96 SAFETY receives the updated tire pressures. The vehicle may need CAUTION! to be driven for up to 20 minutes above 15 mph (24 km/h) in order for the TPMS to receive this information. • The TPMS has been optimized for the original equipment tires and wheels.
Page 99 SAFETY NOTE: The TPMS uses wireless technology with wheel rim mounted electronic sensors to monitor tire pressure levels. • The TPMS is not intended to replace normal tire care and Sensors, mounted to each wheel as part of the valve stem, maintenance or to provide warning of a tire failure or transmit tire pressure readings to the Receiver Module.
Page 100 98 SAFETY been received. The vehicle may need to be driven for up to NOTE: Your vehicle is equipped with a regular size spare 20 minutes above 15 mph (24 km/h) to receive this wheel. information. 1. The spare tire has a tire pressure monitoring sensor, but Check TPMS Warnings it is not monitored until it is mounted in place of any of the existing four road tires.
Page 101: Occupant Restraint Systems
SAFETY General Information Some of the safety features described in this section may be standard equipment on some models, or may be optional This device complies with Part 15 of the FCC rules and RSS equipment on others. If you are not sure, ask your autho- 210 of Industry Canada.
Page 102: Seat Belt Systems
100 SAFETY restraints or belt-positioning booster seats should ride WARNING! properly buckled up in a vehicle with a rear seat. • Never place a rear-facing child restraint in front of an 4. Never allow children to slide the shoulder belt behind air bag.
Page 103 SAFETY Enhanced Seat Belt Use Reminder System (BeltAlert) BeltAlert) (the outboard front passenger seat BeltAlert is not active when the outboard front passenger seat is Driver and Passenger BeltAlert (if equipped) unoccupied). The BeltAlert warning sequence starts by BeltAlert is a feature intended to remind the driver blinking the Seat Belt Reminder Light and sounding an and outboard front seat passenger (if equipped with intermittent chime.
Page 104 102 SAFETY pets be restrained in the rear seat (if equipped) in pet WARNING! harnesses or pet carriers that are secured by seat belts, and cargo is properly stowed. • Relying on the air bags alone could lead to more severe injuries in a collision.
Page 105 SAFETY WARNING! (Continued) WARNING! (Continued) position to minimize the risk of severe injury or belt is flat against your body, without twists. If you death in the event of a crash. can’t straighten a seat belt in your vehicle, take it to •...
Page 106 104 SAFETY WARNING! (Continued) likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together. • A frayed or torn seat belt could rip apart in a collision and leave you with no protection.
Page 107 SAFETY Inserting Latch Plate Into Buckle Positioning The Lap Belt 4. Position the lap belt so that it is snug and lies low across 5. Position the shoulder belt across the shoulder and chest your hips, below your abdomen. To remove slack in the with minimal, if any slack so that it is comfortable and lap belt portion, pull up on the shoulder belt.
Page 108 106 SAFETY Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 109 SAFETY WARNING! • Wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of the seat belt. Follow these instructions to wear your seat belt safely and to keep your passengers safe, too. •...
Page 110 108 SAFETY Seat Belts And Pregnant Women Seat Belt Pretensioner The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision.
Page 111 SAFETY Switchable Automatic Locking Retractor (ALR) The seat belt in the passenger seating position is equipped with a Switchable Automatic Locking Retractor (ALR) which is used to secure a child restraint system. For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt”...
Page 112 110 SAFETY In Automatic Locking Mode, the shoulder belt is automati- 3. Allow the seat belt to retract. As the seat belt retracts, cally pre-locked. The seat belt will still retract to remove you will hear a clicking sound. This indicates the seat any slack in the shoulder belt.
Page 113: Supplemental Restraint Systems (Srs)
SAFETY Supplemental Restraint Systems (SRS) • Seat Belt Pretensioners Some of the safety features described in this section may be Air Bag Warning Light standard equipment on some models, or may be optional The ORC monitors the readiness of the electronic parts of equipment on others.
Page 114 112 SAFETY detected that could affect the air bag system. The diagnos- WARNING! tics also record the nature of the malfunction. While the air bag system is designed to be maintenance free, if any of the Ignoring the Air Bag Warning Light in your instrument following occurs, have an authorized dealer service the air panel could mean you won’t have the air bag system to bag system immediately.
Page 115 SAFETY WARNING! (Continued) • Never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.
Page 116 114 SAFETY On the other hand, depending on the type and location of WARNING! (Continued) impact, front air bags may deploy in crashes with little • Do not put anything on or around the air bag covers vehicle front-end damage but that produce a severe initial or attempt to open them manually.
Page 117 SAFETY Supplemental Side Air Bags Supplemental Seat-Mounted Side Air Bags (SABs) This vehicle is equipped with Supplemental Seat-Mounted Side Air Bags (SABs). Supplemental Seat-Mounted Side Air Bags (SABs) are located in the outboard side of the front seats. The SABs are marked with a “SRS AIRBAG”...
Page 118 116 SAFETY WARNING! Do not use accessory seat covers or place objects between you and the Side Air Bags; the performance could be adversely affected and/or objects could be pushed into you, causing serious injury. Supplemental Side Air Bag Inflatable Curtains (SABICs) This vehicle is equipped with Supplemental Side Air Bag Inflatable Curtains (SABICs).
Page 119 SAFETY positioned in the area where the SABICs inflate. Children Side Impacts are at an even greater risk of injury from a deploying air The Side Air Bags are designed to activate in certain side bag. impacts. The Occupant Restraint Controller (ORC) deter- The SABICs may help reduce the risk of partial or complete mines whether the deployment of the Side Air Bags in a ejection of vehicle occupants through side windows in...
Page 120 118 SAFETY Side Air Bags are a supplement to the seat belt restraint WARNING! system. Side Air Bags deploy in less time than it takes to blink your eyes. • Side Air Bags need room to inflate. Do not lean against the door or window.
Page 121 SAFETY The Side Air Bags will not deploy in all rollover events. The • Front and Side Impact Sensors rollover sensing system determines if a rollover event may • Seat Belt Pretensioners be in progress and whether deployment is appropriate. In If A Deployment Occurs the event the vehicle experiences a rollover or near rollover event, and deployment of the Side Air Bags is appropriate,...
Page 122 120 SAFETY inflation. These airborne particles may irritate the skin, NOTE: eyes, nose, or throat. If you have skin or eye irritation, • Air bag covers may not be obvious in the interior trim, rinse the area with cool water. For nose or throat but they will open during air bag deployment.
Page 123 SAFETY NOTE: After an accident, remember to cycle the ignition to the STOP (OFF/LOCK) position and remove the key from the ignition switch to avoid draining the battery. Carefully check the vehicle for fuel leaks in the engine compartment and on the ground near the engine compartment and fuel tank before resetting the system and starting the engine.
Page 124 122 SAFETY Maintaining Your Air Bag System WARNING! (Continued) dealer. Only manufacturer approved seat accessories WARNING! may be used. If it is necessary to modify the air bag • Modifications to any part of the air bag system could system for persons with disabilities, contact your cause it to fail when you need it.
Page 125: Child Restraints
SAFETY Child Restraints These data can help provide a better understanding of the circumstances in which crashes and injuries occur. Everyone in your vehicle needs to be buckled up at all times, including babies and children. Every state in the NOTE: EDR data are recorded by your vehicle only if a United States, and every Canadian province, requires that non-trivial crash situation occurs;...
Page 126 124 SAFETY There are different sizes and types of restraints for children NOTE: from newborn size to the child almost large enough for an • For additional information, refer to www.safercar.gov/ adult safety belt. Always check the child seat Owner’s parents/index.htm or call: 1–888–327–4236 Manual to make sure you have the correct seat for your •...
Page 127 SAFETY Recommended Type Of Child Re- Child Size, Height, Weight Or Age straint Larger Children Children who have outgrown their Belt Positioning Booster Seat and the forward-facing child restraint, but vehicle seat belt, seated in the rear are too small to properly fit the vehi- seat of the vehicle cle’s seat belt Children Too Large for Child Re-...
Page 128 126 SAFETY Older Children And Child Restraints WARNING! Children who are two years old or who have outgrown • Improper installation can lead to failure of an infant their rear-facing convertible child seat can ride forward- or child restraint. It could come loose in a collision. facing in the vehicle.
Page 129 SAFETY should use the seat belt in a rear seat. Use this simple 5-step WARNING! test to decide whether the child can use the vehicle’s seat belt alone: Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt 1.
Page 130 128 SAFETY necessary to use a locking clip. The ALR retractor can be WARNING! “switched” into a locked mode by pulling all of the webbing out of the retractor and then letting the webbing Rear-facing infant restraints must never be secured in retract back into the retractor.
Page 131 SAFETY WARNING! • Improper installation or failure to properly secure a child restraint can lead to failure of the restraint. The child could be badly injured or killed. • Follow the child restraint manufacturer’s directions exactly when installing an infant or child restraint. 1.
Page 132: Transporting Pets
130 SAFETY SAFETY TIPS 6. Try to pull the webbing out of the retractor. If it is locked, you should not be able to pull out any webbing. Transporting Passengers If the retractor is not locked, repeat step 5. NEVER TRANSPORT PASSENGERS IN THE CARGO 7.
Page 133: Exhaust Gas
SAFETY Exhaust Gas vehicle, or when the underside or rear of the vehicle is damaged, have a competent mechanic inspect the complete WARNING! exhaust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or Exhaust gases can injure or kill.
Page 134: Windshield
132 SAFETY have the system inspected at your authorized dealer as WARNING! soon as possible. After the bulb check, this light will illuminate with a single chime when a fault with the Air An improperly attached, damaged, folded, or stacked Bag System has been detected.
Page 135: Periodic Safety Checks You Should Make Outside
SAFETY WARNING! (Continued) WARNING! (Continued) vehicle properly parked with the engine off, fully interference with the accelerator, brake, or clutch depress the accelerator, the brake, and the clutch pedals then re-install the floor mats. • It is recommended to only use mild soap and water pedal (if present) to check for interference.
Page 136 134 SAFETY Door Latches Check for proper closing, latching, and locking. Fluid Leaks Check area under the vehicle after overnight parking for fuel, coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, or brake fluid leaks are suspected.
Page 137 STARTING AND OPERATING CONTENTS STARTING THE ENGINE ....137 POWER STEERING ..... .149 ▫...
Page 138 136 STARTING AND OPERATING ▫ Cleaning The ParkSense System... . .156 TRAILER TOWING ..... .163 ▫...
Page 139: Starting The Engine
STARTING AND OPERATING 137 STARTING THE ENGINE Normal Starting Before starting your vehicle, adjust your seat, adjust both NOTE: Normal starting of either a cold or a warm engine inside and outside mirrors, and fasten your seat belts. is obtained without pumping or pressing the accelerator pedal.
Page 140: After Starting
138 STARTING AND OPERATING The engine block heater must be plugged in at least one WARNING! (Continued) hour to have an adequate warming effect on the engine. • Do not attempt to push or tow your vehicle to get it started.
Page 141: Parking Brake
STARTING AND OPERATING 139 under which vehicle operations will occur. For the recom- mended viscosity and quality grades, refer to “Fluids And Lubricants” in “Technical Specifications”. CAUTION! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. NOTE: A new engine may consume some oil during its first few thousand miles (kilometers) of operation.
Page 142: Automatic Transmission
140 STARTING AND OPERATING WARNING! CAUTION! • Never use the PARK position as a substitute for the If the Brake System Warning Light remains on with the parking brake released, a brake system malfunction is parking brake. Always apply the parking brake fully indicated.
Page 143: Key Ignition Park Interlock
STARTING AND OPERATING 141 WARNING! (Continued) CAUTION! the transmission into PARK, turn the engine OFF, Damage to the transmission may occur if the following and remove the ignition key. Once the key is re- precautions are not observed: moved, the transmission is locked in PARK, securing •...
Page 144: Brake/Transmission Shift Interlock System
142 STARTING AND OPERATING Brake/Transmission Shift Interlock System may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles This vehicle is equipped with a Brake Transmission Shift (kilometers). Interlock System (BTSI) that holds the transmission gear selector in PARK unless the brakes are applied.
Page 145 STARTING AND OPERATING 143 displays the current gear in the instrument cluster, and Never attempt to use PARK while the vehicle is in motion. prevents automatic upshifts beyond this gear. In ERS Apply the parking brake when exiting the vehicle in this mode, toggling the gear selector forward (-) or rearward (+) range.
Page 146 144 STARTING AND OPERATING WARNING! WARNING! (Continued) the transmission into PARK, turn the engine OFF, • Never use the PARK position as a substitute for the and remove the ignition key. Once the key is re- parking brake. Always apply the parking brake fully moved, the transmission is locked in PARK, securing when exiting the vehicle to guard against vehicle the vehicle against unwanted movement.
Page 147 STARTING AND OPERATING 145 • Look at the transmission gear position display and started in this range. Apply the parking brake and shift the verify that it indicates the PARK position (P). transmission into PARK if you must exit the vehicle. •...
Page 148 146 STARTING AND OPERATING upshifts through all forward gears. The DRIVE position Transmission Limp Home Mode provides optimum driving characteristics under all normal Transmission function is monitored electronically for ab- operating conditions. normal conditions. If a condition is detected that could result in transmission damage, Transmission Limp Home When frequent transmission shifting occurs (such as when Mode is activated.
Page 149 STARTING AND OPERATING 147 NOTE: Even if the transmission can be reset, we recom- the ERS position (beside DRIVE) will activate ERS mode, mend that you visit your authorized dealer at your earliest display the current gear in the instrument cluster, and set possible convenience.
Page 150 148 STARTING AND OPERATING NOTE: To select the proper gear position for maximum potential for transmission overheating or failure due to deceleration (engine braking), move the gear selector into excessive shifting. When operating in TOW/HAUL mode, the ERS position, then tap it forward (-) repeatedly as the transmission upshifts are delayed, and the transmission vehicle slows.
Page 151: Power Steering
STARTING AND OPERATING 149 NOTE: If for some reason the power assist is interrupted, it will still be possible to steer your vehicle. Under these condi- • The torque converter clutch will not engage, until the tions, you will observe a substantial increase in steering transmission fluid and engine coolant are warm [usually effort, especially at very low vehicle speeds and during after 1 to 3 miles (2 to 5 km) of driving].
Page 152: Power Steering Fluid Check
150 STARTING AND OPERATING Power Steering Fluid Check surfaces. Refer to “Fluids, Lubricants And Genuine Parts” in “Maintaining Your Vehicle” for further information. Checking the power steering fluid level at a defined service interval is not required. The fluid should be checked at SPEED CONTROL every oil change if a leak is suspected, abnormal noises are When engaged, the Speed Control takes over accelerator...
Page 153: To Activate
STARTING AND OPERATING 151 To Set A Desired Speed NOTE: In order to ensure proper operation, the Speed Control System has been designed to shut down if multiple Turn the Speed Control on. When the vehicle has reached Speed Control functions are operated at the same time. If the desired speed, move the Speed Control lever upward this occurs, the Speed Control System can be reactivated by (SET +) and release.
Page 154: To Accelerate For Passing
152 STARTING AND OPERATING • If the lever is continually held up, the set speed will • If the lever is continually held down, the set speed will continue to increase until the lever is released, then the continue to decrease until the lever is released, then the new set speed will be established.
Page 155: To Resume Speed
STARTING AND OPERATING 153 PARKSENSE REAR PARK ASSIST — IF EQUIPPED WARNING! The ParkSense Rear Park Assist system provides an au- Speed Control can be dangerous where the system dible indication of the distance between the rear fascia/ cannot maintain a constant speed. Your vehicle could bumper and a detected obstacle when backing up, e.g.
Page 156: Parksense Rear Park Assist Alerts
154 STARTING AND OPERATING ParkSense Rear Park Assist Alerts (60 cm) from the corners of the rear fascia/bumper, de- pending on the location, type and orientation of the If an obstacle is behind the vehicle when REVERSE gear is obstacle. engaged, an audible alert is activated.
Page 157 STARTING AND OPERATING 155 Audible And Visual Signals Supplied By The ParkSense Rear Park Assist System SIGNAL MEANING INDICATION Obstacle Distance An obstacle is present within the sensors’ Audible signal (dashboard loudspeaker) field of view • Sound pulses emitted at a rate that in- creases as the distance decreases.
Page 158: Parksense Rear Park Assist Failure Indications
156 STARTING AND OPERATING ParkSense Rear Park Assist Failure Indications jet/high pressure washing nozzles at least 4 inches (10 cm) from the sensors. Do not scratch or poke the sensors. A malfunction of the ParkSense Rear Park Assist sensors or Otherwise, you could damage the sensors.
Page 159: Parkview Rear Back Up Camera
STARTING AND OPERATING 157 the system misinterpreting a close object as a sensor CAUTION! problem, causing a failure indication to be displayed in the instrument cluster display. • ParkSense is only a parking aid and it is unable to recognize every obstacle, including small obstacles. WARNING! Parking curbs might be temporarily detected or not detected at all.
Page 160 158 STARTING AND OPERATING are opened. The image will be displayed on the touch- When the vehicle is shifted out of REVERSE and/or when screen display along with a caution note to “check entire the rear doors are closed, the rear camera mode is exited surroundings”...
Page 161: Refueling The Vehicle
STARTING AND OPERATING 159 NOTE: ParkView Rear Back Up Camera can be enabled or NOTE: If snow, ice, mud, or any foreign substance builds disabled by Uconnect system menu. up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.
Page 162: Loose Fuel Filler Cap Message
160 STARTING AND OPERATING WARNING! CAUTION! (Continued) off” the fuel tank after filling. When the fuel nozzle • Never have any smoking materials lit in or near the “clicks” or shuts off, the fuel tank is full. vehicle when the fuel door is open or the tank is being filled.
Page 163: Vehicle Loading
STARTING AND OPERATING 161 is properly tightened. Refer to “Onboard Diagnostic Sys- • Gross Axle Weight Rating (GAWR) rear tem” in “Getting To Know Your Instrument Panel” for • Vehicle Identification Number (VIN) further information. • Type of vehicle If the problem continues, the message will appear the next •...
Page 164: Tire Size
162 STARTING AND OPERATING Tire Size Overloading The tire size on the Vehicle Certification Label represents The load carrying components (axle, springs, tires, wheels, the actual tire size on your vehicle. Replacement tires must etc.) of your vehicle will provide satisfactory service as be equal to the load capacity of this tire size.
Page 165: Loading
STARTING AND OPERATING 163 Loading Common Towing Definitions To load your vehicle properly, first figure out its empty The following trailer towing related definitions will assist weight, axle-by-axle and side-by-side. Store heavier items you in understanding the following information: down low and be sure you distribute their weight as Gross Vehicle Weight Rating (GVWR) evenly as possible.
Page 166 164 STARTING AND OPERATING Gross Axle Weight Rating (GAWR) Trailer Sway Control The GAWR is the maximum capacity of the front and rear The trailer sway control can be a mechanical telescoping axles. Distribute the load over the front and rear axles link that can be installed between the hitch receiver and the evenly.
Page 167 STARTING AND OPERATING 165 Weight-Distributing Hitch WARNING! A weight-distributing system works by applying leverage • An improperly adjusted Weight Distributing Hitch through spring (load) bars. They are typically used for system may reduce handling, stability, braking per- heavier loads to distribute trailer tongue weight to the tow formance, and could result in a collision.
Page 168: Trailer Hitch Classification
166 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
Page 169: Trailer Towing Weights (Maximum Trailer Weight Ratings)
STARTING AND OPERATING 167 Trailer Towing Weights (Maximum Trailer Weight Consider the following items when computing the weight Ratings) on the rear axle of the vehicle: • The tongue weight of the trailer. NOTE: For trailer towing information (maximum trailer weight ratings) refer to the following website addresses: •...
Page 170 168 STARTING AND OPERATING CAUTION! WARNING! (Continued) control. You could lose control of your vehicle and • Do not tow a trailer at all during the first 500 miles have a collision. (805 km) the new vehicle is driven. The engine, axle •...
Page 171 STARTING AND OPERATING 169 Maintenance” for the proper tire replacement proce- WARNING! (Continued) dures. Replacing tires with a higher load carrying capac- ity will not increase the vehicle’s GVWR and GAWR 1. GVWR limits. 2. GTW Towing Requirements — Trailer Brakes 3.
Page 172 170 STARTING AND OPERATING The Trailer Tow Package may include a four- and seven-pin WARNING! wiring harness. Use a factory approved trailer harness and connector. • Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail.
Page 173: Towing Tips
STARTING AND OPERATING 171 NOTE: • Disconnect trailer wiring connector from the vehicle before launching a boat (or any other device plugged into vehicle’s electrical connect) into water. • Be sure to reconnect after clear from water area. Seven-Pin Connector 1 —...
Page 174 172 STARTING AND OPERATING Automatic Transmission Speed Control — If Equipped • Do not use on hilly terrain or with heavy loads. The DRIVE range can be selected when towing. The transmission controls include a drive strategy to avoid • When using the speed control, if you experience speed frequent shifting when towing.
Page 175: Recreational Towing
STARTING AND OPERATING 173 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Towing Condition Wheels OFF the Ground Automatic Transmission Flat Tow NONE NOT ALLOWED Dolly Tow Front Rear NOT ALLOWED On Trailer NOTE: When towing your vehicle, always follow applicable state and provincial laws. Contact state and provincial Highway Safety offices for additional details.
Page 176: Driving Tips
174 STARTING AND OPERATING Traction CAUTION! (Continued) When driving on wet or slushy roads, it is possible for a • Towing this vehicle in violation of the above require- wedge of water to build up between the tire and road ments can cause severe transmission damage.
Page 177 STARTING AND OPERATING 175 Flowing/Rising Water WARNING! (Continued) • Driving through standing water limits your vehicle’s WARNING! braking capabilities, which increases stopping dis- Do not drive on or across a road or path where water is tances. Therefore, after driving through standing flowing and/or rising (as in storm run-off).
Page 178 176 STARTING AND OPERATING CAUTION! (Continued) • Driving through standing water may cause damage to your vehicle’s drivetrain components. Always in- spect your vehicle’s fluids (i.e., engine oil, transmis- sion, axle, etc.) for signs of contamination (i.e., fluid that is milky or foamy in appearance) after driving through standing water.
Page 179: Gear Selector
IN CASE OF EMERGENCY CONTENTS HAZARD WARNING FLASHERS ... .179 ▫ Wheel Covers ......206 BULB REPLACEMENT .
Page 180 178 IN CASE OF EMERGENCY TOWING A DISABLED VEHICLE ... .221 EVENT DATA RECORDER (EDR) ... .223 ▫ Automatic Transmission ....222 ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) .
Page 181: Hazard Warning Flashers
IN CASE OF EMERGENCY 179 HAZARD WARNING FLASHERS This is an emergency warning system and it should not be used when the vehicle is in motion. Use it when your The Hazard Warning flasher switch is located on the vehicle is disabled and it is creating a safety hazard for instrument panel below the climate controls.
Page 182 180 IN CASE OF EMERGENCY Exterior Bulbs Bulb Number Front Low and High Beam Headlamp H7LL Front Park/Turn Signal Lamps 7444NA Daytime Running Lamps (If Equipped) 7440 Front Side Marker Lamps WY5W Rear Tail/Stop Lamps 7443 Rear Turn Signal Lamps 7440NA Rear Backup Lamps Rear Side Marker Lamps...
Page 183: Replacing Exterior Bulbs
IN CASE OF EMERGENCY 181 Replacing Exterior Bulbs 12. Install access cap. Headlamps Low Beam And High beam 13. Carefully reinstall headlamp in the same position on the vehicle, so as not to affect headlamp aiming. NOTE: Passenger side headlamp must be removed for bulb replacement, for driver side headlamp go to step 6 14.
Page 184 182 IN CASE OF EMERGENCY 7. Install the bulb into socket, and rotate bulb/socket 5. Pull Headlamp forward. clockwise into lamp locking it in place. 6. Remove the DRL, side marker bulb by pulling straight 8. Carefully reinstall headlamp in the same position on the out.
Page 185: Replacing Interior Bulbs
IN CASE OF EMERGENCY 183 Replacing Interior Bulbs 5. Reinstall the plastic cap and close the cover on the wheel liner. Cargo Lamp Front, Rear Roof Lamps 1. Using a suitable tool, remove either the lamp above the 1. Remove two screw and remove the lamp assembly. back door or the sliding door lamp as needed and disconnect it.
Page 186 184 IN CASE OF EMERGENCY 2. Using a suitable tool, pull open the metal bulb access on Dome Lamps the back of the housing. 1. Using a suitable tool, insert the tip at the location shown and press inward to the lamp to relieve the spring tension.
Page 187 IN CASE OF EMERGENCY 185 2. Using a suitable tool, flex the housing to lift the light pod cover away from the unit. Dome Lamp Light Bulbs 4. Close the housing cover making sure it snaps together properly and connect the lamp. Dome Lamp Light Pod Cover 3.
Page 188: Fuses
186 IN CASE OF EMERGENCY FUSES Underhood Fuses The Front Power Distribution Center is located on the WARNING! driver’s side of the engine compartment. To access the fuses, remove the cover. • When replacing a blown fuse, always use an appro- priate replacement fuse with the same amp rating as the original fuse.
Page 189 IN CASE OF EMERGENCY 187 Cavity Maxi Fuse Mini Fuse Description 40 Amp Orange – Electronic Stability Control (ESC) Pump 20 Amp Yellow (3.6 – Starter Relay 3.6L (3.6 Gasoline Engine) Gasoline Engine) 30 Amp Green UREA (3.0 Diesel Engine) 50 Amp Red (3.0 Diesel –...
Page 190 188 IN CASE OF EMERGENCY Cavity Maxi Fuse Mini Fuse Description – 15 Amp Blue Rear Power Outlet – 15 Amp Blue Horn – 15 Amp Blue Fuel Pressure Regulator (MPROP)-DRV (3.0 Diesel Engine) — If Equipped – 20 Amp Yellow Power Outlet –...
Page 191 IN CASE OF EMERGENCY 189 Cavity Maxi Fuse Mini Fuse Description – 7.5 Amp Brown KL30 Manual Transmission Automated (MTA), KL30 Engine Control Module (ECM), KL30 Main Relay Coil (3.0 Diesel Engine) – 7.5 Amp Brown A/C Compressor — If Equipped –...
Page 192 190 IN CASE OF EMERGENCY Front PDC Additional Fuses The additional fuse box is located inside the front PDC Box. Front Power Distribution Center Additional Fuses Cavity Mini Fuse Description 20 Amp Yellow Vacuum Pump (3.6 Gasoline Engine) — If Equipped 30 Amp Green Transmission Power RELE (3.6 Gasoline Engine) —...
Page 193: Interior Fuses
IN CASE OF EMERGENCY 191 Interior Fuses The interior fuse panel is part of the Body Control Module (BCM) and is located on the driver’s side under the instrument panel. Fuse Panel...
Page 194 192 IN CASE OF EMERGENCY Fuse Panel Cavity Locations Cavity Mini Fuse Description 5 Amp Beige INT/A 7.5 Amp Brown Clearance Lights...
Page 195 IN CASE OF EMERGENCY 193 Cavity Mini Fuse Description 15 Amp Blue +30 (ACM – TPCU – RRM – DLC) 5 Amp Beige INT (BRAKE NO – IPC) 15 Amp Blue Central Locking 5 Amp Beige INT (BSM – SAS – BRAKE NC) 20 Amp Yellow Bi-Directional Washer Pump 20 Amp Yellow...
Page 196: Right Central Pillar Fuses
194 IN CASE OF EMERGENCY Right Central Pillar Fuses The right central pillar fuse panel is located on the interior side at the base of the passenger side B pillar. Fuse Panel Fuse Panel Location Cavity Mini Fuse Description 7.5 Amp Brown Seat Heater 20 Amp Yellow Rear Left Windows Heater...
Page 197: Jacking And Tire Changing
IN CASE OF EMERGENCY 195 JACKING AND TIRE CHANGING Jack Location The jack and jack tools are stored under the front passenger WARNING! seat. • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.
Page 198 196 IN CASE OF EMERGENCY To open the jack kit container you must push the containers CAUTION! release to separate the top and bottom. Do not force lock knob over limit. Damage to lock knob may occur. Container Release Lock Knob 1 —...
Page 199: Spare Tire Removal
IN CASE OF EMERGENCY 197 Spare Tire Removal 1. Remove the spare tire before attempting to jack up the vehicle. Attach the lug bolt adapter to the winch exten- sion and insert it into the winch mechanism. Jacking Tools 1 — Wrench Handle 2 —...
Page 200 198 IN CASE OF EMERGENCY Winch Location Winch Extension The winch mechanism is located under the rear of the 2. Rotate the wheel wrench handle counterclockwise until vehicle to the right of the spare tire. the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
Page 201 IN CASE OF EMERGENCY 199 Lowering Spare Tire Spare Tire 3. Pull the spare tire out from under the vehicle to gain 4. Lift the spare tire with one hand to give clearance to tilt access to the spare tire retainer. the retainer at the end of the cable.
Page 202: Preparations For Jacking
200 IN CASE OF EMERGENCY Lifting Spare Tire Retainer 5. Pull the retainer through the center of the wheel. Preparations For Jacking 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel.
Page 203: Jacking Instructions
IN CASE OF EMERGENCY 201 2. Turn on the Hazard Warning flasher. WARNING! (Continued) 3. Apply the parking brake firmly. • Turn on the Hazard Warning flashers. • Block the wheel diagonally opposite the wheel to be 4. Place the transmission in PARK (REVERSE for manual raised.
Page 204 202 IN CASE OF EMERGENCY Jack Warning Label Assembled Jack 1. Loosen (but do not remove) the wheel lug bolts by CAUTION! turning them to the left one turn while the wheel is still on the ground. Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking 2.
Page 205 IN CASE OF EMERGENCY 203 Jacking Engagement Locations Rear Jacking Location NOTE: The front jacking location is located behind the CAUTION! front tire and in front of the driver/passenger door. Do not attempt to raise the vehicle by jacking on locations other than those indicated.
Page 206 204 IN CASE OF EMERGENCY 3. Place the wrench handle and lug bolt adapter on the jack screw and turn to the right until the jack head is properly engaged in the described location. Do not raise the vehicle until you are sure the jack is securely engaged.
Page 207 IN CASE OF EMERGENCY 205 CAUTION! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. NOTE: Do not install the wheel cover on the spare tire. 7.
Page 208: Wheel Covers
206 IN CASE OF EMERGENCY The wheel covers on the vehicle are held in place by the WARNING! wheel lug bolts and can be removed after the wheel lug bolts are taken off. A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle.
Page 209: Tire Service Kit Components And Operation
IN CASE OF EMERGENCY 207 Tire Service Kit Components And Operation Using The Mode Select Knob And Hoses Your Tire Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob (5) and turn to this position for air pump operation only.
Page 210: Tire Service Kit Usage Precautions
208 IN CASE OF EMERGENCY Tire Service Kit Usage Precautions • When the Tire Service Kit sealant is in a liquid form, clean water, and a damp cloth will remove the material • Replace the Tire Service Kit Sealant Bottle (1) and Sealant from the vehicle or tire and wheel components.
Page 211: Sealing A Tire With Tire Service Kit
IN CASE OF EMERGENCY 209 WARNING! WARNING! (Continued) in injuries that are serious or fatal to you, your • Do not attempt to seal a tire on the side of the vehicle passengers, and others around you. closest to traffic. Pull far enough off the road to avoid •...
Page 212 210 IN CASE OF EMERGENCY 2. Verify that the valve stem (on the wheel with the 5. Uncoil the Power Plug (8) and insert the plug into the deflated tire) is in a position that is near to the ground. vehicle’s 12 Volt power outlet.
Page 213 IN CASE OF EMERGENCY 211 Select Knob (5) is in the Sealant Mode position and not 2. The pump will start to inject air into the tire immedi- Air Mode. Push the Power Button (4) to turn On the Tire ately after the Sealant Bottle (1) is empty.
Page 214 212 IN CASE OF EMERGENCY 3. Immediately disconnect the Sealant Hose (6) from the WARNING! valve stem, reinstall the cap on the fitting at the end of the hose, and place the Tire Service Kit in the vehicle Tire Service Kit is not a permanent flat tire repair. Have storage location.
Page 215 IN CASE OF EMERGENCY 213 If tire pressure is less than 19 psi (1.3 Bar): 6. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at an authorized dealer as soon as possible. The tire is too badly damaged. Do not attempt to drive the Refer to (F) “Sealant Bottle And Hose Replacement”.
Page 216: Jump Starting
214 IN CASE OF EMERGENCY 6. Verify that the cap is installed on the fitting at the end of CAUTION! the Sealant Hose (6) and return the hose to its storage area (located on the bottom of the air pump). Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 7.
Page 217 IN CASE OF EMERGENCY 215 WARNING! (Continued) • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
Page 218: Jump Starting Procedure
216 IN CASE OF EMERGENCY Jump Starting Procedure 4. Connect the opposite end of the negative (-) jumper cable to the remote negative (-) post of the discharged WARNING! vehicle. NOTE: The remote negative (-) post is located in the front Failure to follow this jump starting procedure could of the engine compartment on the driver’s side.
Page 219: Battery Location
IN CASE OF EMERGENCY 217 Battery Location 2. Disconnect the opposite end of the negative (-) jumper cable from the negative (-) post of the booster battery. There are two remote jump starting posts under the hood which is the recommended jump start location. If access to 3.
Page 220: If Your Engine Overheats
218 IN CASE OF EMERGENCY NOTE: There are steps that you can take to slow down an impending overheat condition: • If your air conditioner (A/C) is on, turn it off. The A/C system adds heat to the engine cooling system and turning the A/C off can help remove this heat.
Page 221: Gear Selector Override
IN CASE OF EMERGENCY 219 5. Insert the screwdriver or similar tool into the access CAUTION! port, and push and hold the override release lever forward. Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull 6.
Page 222 220 IN CASE OF EMERGENCY CAUTION! WARNING! (Continued) failure, of the axle and tires. A tire could explode and Racing the engine or spinning the wheels may lead to injure someone. Do not spin your vehicle’s wheels transmission overheating and failure. Allow the en- faster than 30 mph (48 km/h) or for longer than 30 gine to idle with the transmission in NEUTRAL for at seconds continuously without stopping when you are...
Page 223 IN CASE OF EMERGENCY 221 TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Towing Condition Wheels OFF The ALL Models Ground Flat Tow NONE If transmission is operable: • Transmission in NEUTRAL Wheel Lift Or Dolly Rear •...
Page 224 222 IN CASE OF EMERGENCY CAUTION! CAUTION! • Do not use sling type equipment when towing. • Towing faster than 25 mph (40 km/h) or farther than Vehicle damage may occur. 15 miles (24 km) with front wheels on the ground can •...
Page 225 IN CASE OF EMERGENCY 223 EVENT DATA RECORDER (EDR) This vehicle is equipped with an Event Data Recorder (EDR). The main purpose of an EDR is to record data that will assist in understanding how a vehicle’s systems per- formed under certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle.
Page 227 SERVICING AND MAINTENANCE CONTENTS SCHEDULED SERVICING ....227 ▫ Windshield Wiper Blades ....239 ▫...
Page 228 226 SERVICING AND MAINTENANCE ▫ Tire Rotation Recommendations ... .270 ▫ Body And Underbody Maintenance ..273 DEPARTMENT OF TRANSPORTATION UNIFORM ▫ Preserving The Bodywork ....273 TIRE QUALITY GRADES .
Page 229: Scheduled Servicing
SERVICING AND MAINTENANCE 227 SCHEDULED SERVICING NOTE: Under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 Your vehicle is equipped with an automatic oil change hours of engine run time, whichever comes first. The 350 indicator system.
Page 230: Maintenance Plan
228 SERVICING AND MAINTENANCE Maintenance Plan At Every Oil Change Interval As Indicated By Oil Change Indicator System: Required Maintenance Intervals • Change oil and filter. Refer to the maintenance plan on the following pages for • Rotate the tires. Rotate at the first sign of irregular the required maintenance intervals.
Page 231 SERVICING AND MAINTENANCE 229 Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals, and replace if necessary. Inspect the brake pads, replace as necessary.
Page 232 230 SERVICING AND MAINTENANCE Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Change automatic transmission fluid and filter. Inspect and replace PCV valve if necessary. * The brake fluid change interval is time based only, mileage intervals do not apply. ** The spark plug change interval is mileage based only, yearly intervals do not apply.
Page 233: Heavy Duty Use Of The Vehicle
SERVICING AND MAINTENANCE 231 Heavy Duty Use Of The Vehicle WARNING! Change engine oil at 4,000 miles (6,500 km) or 350 hours of • You can be badly injured working on or around a engine run time if the vehicle is operated in a dusty and off motor vehicle.
Page 234: Engine Compartment
232 SERVICING AND MAINTENANCE ENGINE COMPARTMENT 3.6L Engine 1 — Washer Fluid Reservoir 5 — Power Distribution Center (Fuses) 2 — Engine Oil Fill 6 — Coolant Reservoir 3 — Engine Oil Dipstick 7 — Power Steering Reservoir 4 — Brake Fluid Reservoir...
Page 235: Checking Oil Level - Gas Engine
SERVICING AND MAINTENANCE 233 Checking Oil Level — Gas Engine The washer fluid reservoir will hold a full gallon of fluid when the Low Washer Fluid Light illuminates. To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. Check WARNING! the oil level at regular intervals, such as every fuel stop.
Page 236: Dealer Service
234 SERVICING AND MAINTENANCE WARNING! CAUTION! (Continued) negative post. Battery posts are marked positive (+) • Battery fluid is a corrosive acid solution and can and negative (-) and are identified on the battery burn or even blind you. Do not allow battery fluid to case.
Page 237: Engine Oil
SERVICING AND MAINTENANCE 235 American Petroleum Institute (API) Engine Oil WARNING! Identification Symbol You can be badly injured working on or around a motor vehicle. Only do service work for which you This symbol means that the oil has have the knowledge and the proper equipment. If you been certified by the American Pe- have any doubt about your ability to perform a service troleum Institute (API).
Page 238: Engine Oil Filter
236 SERVICING AND MAINTENANCE The engine oil filler cap also shows the recommended engine oil. Engine oil is an engineered product and its engine oil viscosity for your engine. For information on performance may be impaired by supplemental additives. engine oil filler cap location, refer to the “Engine Compart- Disposing Of Used Engine Oil And Oil Filters ment”...
Page 239: Air Conditioner Maintenance
SERVICING AND MAINTENANCE 237 NOTE: Be sure to follow the “Severe Duty Conditions” cleaning of the condenser fins and a performance test. maintenance interval if applicable. Drive belt tension should also be checked at this time. WARNING! WARNING! • Use only refrigerants and compressor lubricants ap- The air induction system (air cleaner, hoses, etc.) can provide a measure of protection in the case of engine proved by the manufacturer for your air conditioning...
Page 240 238 SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling 1. Remove the two screws that secure the filter retainer to the fresh air inlet, and remove the filter retainer. R-134a Air Conditioning Refrigerant is a hydrofluoro- carbon (HFC) that is an ozone-saving product. However, the manufacturer recommends that air conditioning ser- vice be performed by authorized dealer or other service facilities using recovery and recycling equipment.
Page 241: Body Lubrication
SERVICING AND MAINTENANCE 239 Body Lubrication Locks and all body pivot points, including such items as seat tracks, door hinge pivot points and rollers, liftgate, tailgate, decklid, sliding doors and hood hinges, should be lubricated periodically with a lithium based grease, such as Mopar Spray White Lube to assure quiet, easy operation and to protect against rust and wear.
Page 242: Exhaust System
240 SERVICING AND MAINTENANCE Operation of the wipers on dry glass for long periods may the passenger compartment. In addition, have the exhaust cause deterioration of the wiper blades. Always use washer system inspected each time the vehicle is raised for lubri- fluid when using the wipers to remove salt or dirt from a cation or oil change.
Page 243: Cooling System
SERVICING AND MAINTENANCE 241 vehicle, turn off the engine and allow it to cool. Service, CAUTION! (Continued) including a tune-up to manufacturer’s specifications, and may seriously reduce engine performance and should be obtained immediately. cause serious damage to the engine. To minimize the possibility of catalytic converter damage: •...
Page 244 242 SERVICING AND MAINTENANCE Cooling System — Drain, Flush And Refill WARNING! (Continued) NOTE: Some vehicles require special tools to add coolant • You or others can be badly burned by hot engine properly. Failure to fill these systems properly could lead to coolant (antifreeze) or steam from your radiator.
Page 245 SERVICING AND MAINTENANCE 243 Adding Coolant CAUTION! (Continued) Your vehicle has been built with an improved engine Additive Technology (OAT) engine coolant is differ- coolant (OAT coolant conforming to MS.90032) that allows ent and should not be mixed with Hybrid Organic extended maintenance intervals.
Page 246 244 SERVICING AND MAINTENANCE • Use only high purity water such as distilled or deionized Cooling System Pressure Cap water when mixing the water/engine coolant (anti- The cap must be fully tightened to prevent loss of engine freeze) solution. The use of lower quality water will coolant (antifreeze), and to ensure that engine coolant reduce the amount of corrosion protection in the engine (antifreeze) will return to the radiator from the coolant...
Page 247 SERVICING AND MAINTENANCE 245 community. To prevent ingestion by animals or children, • Check the coolant freeze point in the radiator and in the do not store ethylene glycol-based coolant in open contain- coolant expansion bottle. If engine coolant (antifreeze) ers or allow it to remain in puddles on the ground.
Page 248: Brake System
246 SERVICING AND MAINTENANCE Brake System With disc brakes the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in In order to assure brake system performance, all brake fluid level may be caused by a leak and a system check system components should be inspected periodically.
Page 249: Automatic Transmission (3.6L Gasoline Engine Only)
SERVICING AND MAINTENANCE 247 flushes should be used in any transmission; only the WARNING! (Continued) approved lubricant should be used. to boil unexpectedly during hard or prolonged brak- ing, resulting in sudden brake failure. This could CAUTION! result in a collision. Using a transmission fluid other than the manufactur- •...
Page 250: Raising The Vehicle
248 SERVICING AND MAINTENANCE Fluid And Filter Changes CAUTION! Refer to the “Maintenance Plan” in this section for the Do not use chemical flushes in your transmission as proper maintenance intervals. the chemicals can damage your transmission compo- In addition, change the fluid and filter if the fluid becomes nents.
Page 251 SERVICING AND MAINTENANCE 249 Tire Markings NOTE: • P (Passenger) — Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Example: P215/65R15 95H. • European — Metric tire sizing is based on European design standards.
Page 252 250 SERVICING AND MAINTENANCE Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 253 SERVICING AND MAINTENANCE 251 EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions –...
Page 254 252 SERVICING AND MAINTENANCE Tire Identification Number (TIN) the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the The TIN may be found on one or both sides of the tire; outboard side, then you will find it on the inboard side of however, the date code may only be on one side.
Page 255 SERVICING AND MAINTENANCE 253 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold tire inflation pressure is defined as the tire pressure after the Cold Tire Inflation Pressure vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 256 254 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 257 SERVICING AND MAINTENANCE 255 Tire And Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading”...
Page 258 256 SERVICING AND MAINTENANCE Steps For Determining Correct Load Limit— this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or Metric Example For Load Limit XXX lbs.”...
Page 259 SERVICING AND MAINTENANCE 257 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 260: Tires - General Information
258 SERVICING AND MAINTENANCE Tires — General Information WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
Page 261 SERVICING AND MAINTENANCE 259 Fuel Economy CAUTION! Underinflated tires will increase tire rolling resistance After inspecting or adjusting the tire pressure, always resulting in higher fuel consumption. reinstall the valve stem cap. This will prevent moisture Tread Wear and dirt from entering the valve stem, which could damage the valve stem.
Page 262 260 SERVICING AND MAINTENANCE pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 263 SERVICING AND MAINTENANCE 261 Run Flat Tires — If Equipped WARNING! Run Flat tires allow you the capability to drive 50 miles Fast spinning tires can be dangerous. Forces generated (80 km) at 50 mph (80 km/h) after a rapid loss of inflation by excessive wheel speeds may cause tire damage or pressure.
Page 264 262 SERVICING AND MAINTENANCE Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style. • Tire pressure - Improper cold tire inflation pressures can cause uneven wear patterns to develop across the tire tread.
Page 265 SERVICING AND MAINTENANCE 263 Keep dismounted tires in a cool, dry place with as little It is recommended you contact your authorized tire dealer exposure to light as possible. Protect tires from contact with or original equipment dealer with any questions you may oil, grease, and gasoline.
Page 266: Tire Types
264 SERVICING AND MAINTENANCE Summer Or Three Season Tires — If Equipped WARNING! (Continued) Summer tires provide traction in both wet and dry condi- • Failure to equip your vehicle with tires having ad- tions, and are not intended to be driven in snow or on ice. equate speed capability can result in sudden tire If your vehicle is equipped with Summer tires, be aware failure and loss of vehicle control.
Page 267: Spare Tires - If Equipped
SERVICING AND MAINTENANCE 265 Spare Tires — If Equipped Snow Tires Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 268 266 SERVICING AND MAINTENANCE spare by looking at the spare tire description on the Tire WARNING! (Continued) and Loading Information Placard located on the driver’s needs to be replaced. Be sure to follow the warnings, side door opening or on the sidewall of the tire. Compact which apply to your spare.
Page 269: Wheel And Wheel Trim Care
SERVICING AND MAINTENANCE 267 use spare wheel. This label contains the driving limitations WARNING! for this spare. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not. Compact and Collapsible spares are for temporary Installation of this limited use spare tire affects vehicle emergency use only.
Page 270 268 SERVICING AND MAINTENANCE and to prevent corrosion. Wash wheels with the same soap wheel cleaning chemicals and equipment to prevent dam- solution recommended for the body of the vehicle. age to the wheels. Mopar Wheel Treatment or Mopar Chrome Cleaner or their equivalent is recommended or Your wheels are susceptible to deterioration caused by salt, select a non-abrasive, non-acidic cleaner for aluminum or sodium chloride, magnesium chloride, calcium chloride,...
Page 271: Tire Chains (Traction Devices)
SERVICING AND MAINTENANCE 269 Dark Vapor Chrome, Black Satin Chrome, or Low Gloss WARNING! Clear Coat Wheels Using tires of different size and type (M+S, Snow) CAUTION! between front and rear axles can cause unpredictable handling. You could lose control and have a collision. If your vehicle is equipped with these specialty wheels, DO NOT USE wheel cleaners, abrasives, or CAUTION!
Page 272: Tire Rotation Recommendations
270 SERVICING AND MAINTENANCE The suggested rotation method is the “forward cross” CAUTION! (Continued) shown in the following diagram. This rotation pattern does • Observe the traction device manufacturer’s instruc- not apply to some directional tires that must not be tions on the method of installation, operating speed, reversed.
Page 273: Treadwear
SERVICING AND MAINTENANCE 271 All passenger vehicle tires must conform to Federal WARNING! safety requirements in addition to these grades. The traction grade assigned to this tire is based on Treadwear straight-ahead braking traction tests, and does not The Treadwear grade is a comparative rating, based on include acceleration, cornering, hydroplaning, or the wear rate of the tire when tested under controlled peak traction characteristics.
Page 274: Storing The Vehicle
272 SERVICING AND MAINTENANCE BODYWORK WARNING! Protection From Atmospheric Agents The temperature grade for this tire is established for Vehicle body care requirements vary according to geo- a tire that is properly inflated and not overloaded. graphic locations and usage. Chemicals that make roads Excessive speed, under-inflation, or excessive load- passable in snow and ice and those that are sprayed on ing, either separately or in combination, can cause...
Page 275: Body And Underbody Maintenance
SERVICING AND MAINTENANCE 273 • Salt in the air near seacoast localities. • If insects, tar, or other similar deposits have accumulated on your vehicle, use Mopar Super Kleen Bug and Tar • Atmospheric fallout/industrial pollutants. Remover to remove. Body And Underbody Maintenance •...
Page 276: Interiors
274 SERVICING AND MAINTENANCE • It is important that the drain holes in the lower edges of INTERIORS the doors, rocker panels, and trunk be kept clear and Seats And Fabric Parts open. Use Mopar Total Clean to clean fabric upholstery and •...
Page 277: Plastic And Coated Parts
SERVICING AND MAINTENANCE 275 Plastic And Coated Parts • Do not use any harsh solvents or any other form of protectants on Stain Repel products. Use Mopar Total Clean to clean vinyl upholstery. Seat Belt Maintenance CAUTION! Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners.
Page 278: Leather Parts
276 SERVICING AND MAINTENANCE Leather Parts CAUTION! Mopar Total Clean is specifically recommended for leather Do not use Alcohol and Alcohol-based and/or Ketone upholstery. based cleaning products to clean leather seats, as Your leather upholstery can be best preserved by regular damage to the seat may result.
Page 279 SERVICING AND MAINTENANCE 277 Cleaning The liner is top shelf dishwasher safe, or you may follow the cleaning procedure below. Soak the liner in a mixture of medium hot tap water and one teaspoon of mild liquid dish soap. Let soak for approximately 30 minutes.
Page 281 TECHNICAL SPECIFICATIONS CONTENTS IDENTIFICATION DATA....280 ▫ Do Not Use E-85 In Non-Flex Fuel Vehicles ..283 ▫ Vehicle Identification Number ... . .280 ▫...
Page 282: Identification Data
280 TECHNICAL SPECIFICATIONS IDENTIFICATION DATA BRAKE SYSTEM Your vehicle is equipped with dual hydraulic brake sys- Vehicle Identification Number tems. If either of the two hydraulic systems loses normal The Vehicle Identification Number (VIN) is found on the capability, the remaining system will still function. How- left front corner of the instrument panel, visible through ever, there will be some loss of overall braking effective- the windshield.
Page 283: Torque Specifications
TECHNICAL SPECIFICATIONS 281 Torque Specifications Tighten the lug nuts/bolts in a star pattern until each nut/bolt has been tightened twice. Ensure that the socket is Lug Nut/Bolt **Lug Nut/Bolt Lug Nut/Bolt fully engaged on the lug nut/bolt (do not insert it half- Torque Size Socket Size...
Page 284: Fuel Requirements
282 TECHNICAL SPECIFICATIONS of gasoline with an octane number lower than 87 can cause WARNING! engine failure and may void or not be covered by the New Vehicle Limited Warranty. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle has been Poor quality gasoline can cause problems such as hard lowered.
Page 285: Gasoline/Oxygenate Blends
TECHNICAL SPECIFICATIONS 283 have these additives will help improve fuel economy, CAUTION! reduce emissions, and maintain vehicle performance. DO NOT use E-85, gasoline containing methanol, or Designated TOP TIER Detergent Gaso- gasoline containing more than 15% ethanol (E-15). Use line contains a higher level of detergents of these blends may result in starting and drivability to further aide in minimizing engine problems, damage critical fuel system components,...
Page 286: Cng And Lp Fuel System Modifications
284 TECHNICAL SPECIFICATIONS If a Non-FFV vehicle is inadvertently fueled with E-85 fuel, The manufacturer recommends that gasoline without the engine will have some or all of these symptoms: MMT be used in your vehicle. The MMT content of gasoline may not be indicated on the gasoline pump; •...
Page 287: Carbon Monoxide Warnings
TECHNICAL SPECIFICATIONS 285 CAUTION! (Continued) WARNING! (Continued) these products contain high concentrations of metha- for more than a short period, adjust the ventilation nol. Fuel system damage or vehicle performance system to force fresh, outside air into the vehicle. problems resulting from the use of such fuels or •...
Page 288: Fluid Capacities
286 TECHNICAL SPECIFICATIONS FLUID CAPACITIES U.S. Metric Fuel (Approximate) 24 Gallons 90 Liters Engine Oil With Filter 3.6L Engine (SAE 5W-20, API Certified) 6 Quarts 5.6 Liters Cooling System * 3.6L Engine (Mopar Antifreeze/Engine Coolant 10 Year/ 10.5 Quarts 10 Liters 150,000 Mile Formula or equivalent) FLUIDS AND LUBRICANTS Engine...
Page 289 TECHNICAL SPECIFICATIONS 287 CAUTION! CAUTION! (Continued) and refilled with fresh OAT coolant (conforming to • Mixing of engine coolant (antifreeze) other than MS.90032), by an authorized dealer as soon as pos- specified Organic Additive Technology (OAT) en- sible. gine coolant (antifreeze), may result in engine dam- •...
Page 290: Chassis
288 TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, Or Genuine Part Automatic Transmission – 3.6L Gasoline Engine Only Use Only ATF+4 Automatic Transmission Fluid. Failure to use ATF+4 fluid may affect the function or performance of your transmission. We recommend Mopar ATF+4 Fluid. Brake Master Cylinder We recommend you use Mopar DOT 4.
Page 291 MULTIMEDIA CONTENTS UCONNECT RADIOS ....290 ▫ Introducing Uconnect ....307 CYBERSECURITY .
Page 292: Uconnect Radios
290 MULTIMEDIA UCONNECT RADIOS The risk of unauthorized and unlawful access to your vehicle systems may still exist, even if the most recent For detailed information about your Uconnect radio, refer version of vehicle software (such as Uconnect software) is to your Uconnect Owner’s Manual Supplement.
Page 293: Uconnect Settings
MULTIMEDIA NOTE: and change the customer programmable features. Many features can vary by vehicle. • FCA or your dealer may contact you directly regarding software updates. CAUTION! • To help further improve vehicle security and minimize Do NOT attach any object to the touchscreen, doing so the potential risk of a security breach, vehicle owners can result in damage to the touchscreen.
Page 294: Customer Programmable Features - Uconnect 3 Settings
292 MULTIMEDIA NOTE: The NAV button in the middle of your Uconnect NOTE: radio may also contain the word COMPASS • Only one category may be selected at a time. Customer Programmable Features — Uconnect 3 • The Back arrow will change into a Done button if any Settings changes are made.
Page 295 MULTIMEDIA Language After pressing the “Language” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Set Language NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English/Français/Español) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the “Set Lan- guage”...
Page 296 294 MULTIMEDIA Setting Name Selectable Options the Headlights Off NOTE: This feature is only available in Manual Display Mode. Touchscreen Beep Display Trip B Voice Response Length Brief Detailed Units — If Equipped After pressing the “Units” button on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 297 MULTIMEDIA Voice After pressing the “Voice” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Brief Detailed Length Show Command List Never With Help Always NOTE: This setting will display the possible options while in a voice session. Clock &...
Page 298 296 MULTIMEDIA Setting Name Selectable Options Show Time In Status Bar — If Equipped NOTE: The “Show Time In Status Bar” feature will allow you to turn on or shut off the digital clock in the status bar. Set Date Month Year NOTE:...
Page 299 MULTIMEDIA Lights After pressing the “Lights” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Daytime Running Lights — If Equipped NOTE: When the “Daytime Running Lights” feature is selected, the headlights will turn on whenever the engine is running.
Page 300 298 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Easy Exit Seats — If Equipped Headlight Off Delay 0 sec 30 sec 60 sec 90 sec Engine Off Power 0 sec...
Page 301 MULTIMEDIA Setting Name Selectable Options Balance Speaker Icon Arrow Buttons NOTE: When in this display you may adjust the “Balance/Fade” of the audio by using the “Arrow” button on the touchscreen to adjust the sound level from the front and rear or right and left side speakers. Press the “Speaker Icon” on the touchscreen to reset the balance and fade to the factory setting.
Page 302 300 MULTIMEDIA Setting Name Selectable Options Auto Play NOTE: The Auto Play feature allows an media device to begin playing when the media device is plugged in. To make your selection, press the On or Off buttons to activate or deactivate Auto Play. AUX Volume Offset –...
Page 303 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music channel using one of the twelve presets, so you can enjoy the complete song.
Page 304 302 MULTIMEDIA Setting Name Selectable Options 2. Write down the Sirius ID numbers for your receiver. To reactivate your service, either call the number listed on the screen or visit the provider online. Radio Setup — If Equipped After pressing the “Radio Setup” button (if equipped) on the touchscreen, the following settings will be available: Setting Name Selectable Options...
Page 305 MULTIMEDIA Restore Settings — If Equipped After pressing the “Restore Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Restore Settings Cancel NOTE: When this feature is selected, it will reset the Display, Clock, Audio, and Radio Settings to their default set- tings.
Page 306: Steering Wheel Audio Controls
304 MULTIMEDIA STEERING WHEEL AUDIO CONTROLS Radio Operation The remote sound system controls are located on the Pushing the top of the switch will “Scan” up for the next surface of the steering wheel. listenable station and pushing the bottom of the switch will “Scan”...
Page 307: Usb Charging Port
MULTIMEDIA USB Charging Port The USB connector port can be used for charging purposes only. Use the connection cable to connect an iPod or external USB device to the vehicle’s USB charging port which is located next to the 12V power outlet near the cup holder on passenger side.
Page 308: Radio Operation And Mobile Phones
306 MULTIMEDIA The radiated output power of the internal wireless radio is WARNING! far below the FCC and IC radio frequency exposure limits. Nevertheless, the wireless radio will be used in such a Do not plug in or remove the iPod or external device manner that the radio is 20 cm or further from the human while driving.
Page 309: Uconnect Voice Recognition
MULTIMEDIA The following regulatory statement applies to all Radio • If this equipment does cause harmful interference to Frequency (RF) devices equipped in this vehicle: radio or television reception, which can be determined by turning the equipment off and on, the user is encour- This device complies with Part 15 of the FCC Rules and aged to try to correct the interference by one or more of with Industry Canada license-exempt RSS standard(s).
Page 310 308 MULTIMEDIA 3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is positioned in the dome lamp and aimed at the driver. 4. Each time you give a Voice Command, you must first push either the VR or PHONE button, wait until after the beep, then say your Voice Command.
Page 311: Basic Voice Commands
MULTIMEDIA Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say • Cancel to stop a current voice session • Help to hear a list of suggested Voice Commands •...
Page 312: Media
310 MULTIMEDIA Media TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, push the VR button and say Uconnect offers connections via USB, Bluetooth and Aux- Help. The system will provide you with a list of iliary ports (If Equipped).
Page 313: Phone
MULTIMEDIA Phone TIP: Press the “Browse” button on the touchscreen to see all of the music on your iPod or USB device. Your Voice Making and answering hands-free phone calls is easy with Command must match exactly how the artist, album, song Uconnect.
Page 314: Voice Text Reply
312 MULTIMEDIA TIP: When providing a Voice Command, push the Phone 1. Once an incoming text message is read to you, push the button and say “Call,” then pronounce the name PHONE button . After the beep, say... “Reply.” exactly as it appears in your phone book. When a 2.
Page 315: General Information
MULTIMEDIA General Information Additional Information The following regulatory statement applies to all Radio © 2017 FCA US LLC. All rights reserved. Mopar and Frequency (RF) devices equipped in this vehicle: Uconnect are registered trademarks and Mopar Owner Connect is a trademark of FCA US LLC. Android is a This device complies with Part 15 of the FCC Rules and trademark of Google Inc.
Page 316: Cd/Dvd Disc Maintenance
314 MULTIMEDIA CD/DVD DISC MAINTENANCE To keep a CD/DVD in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge.
Page 317 CUSTOMER ASSISTANCE CONTENTS SUGGESTIONS FOR OBTAINING SERVICE FOR ▫ Customer Assistance For The Hearing Or Speech YOUR VEHICLE ......316 Impaired (TDD/TTY) .
Page 318: Suggestions For Obtaining Service For Your Vehicle
316 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 319: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 317 In Mexico Contact Any communication to the manufacturer’s customer center should include the following information: Av. Prolongacion Paseo de la Reforma, 1240 • Owner’s name and address Sante Fe C.P. 05109 • Owner’s telephone number (home and office) Mexico, D.
Page 320: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
318 CUSTOMER ASSISTANCE Customer Assistance For The Hearing Or Speech questions about the service contract, call the manufactur- Impaired (TDD/TTY) er’s Service Contract National Customer Hotline at 1-800- 521-9922 (Canadian residents, call (800) 465-2001 English / To assist customers who have hearing difficulties, the (800) 387-9983 French).
Page 321: Warranty Information
CUSTOMER ASSISTANCE 319 REPORTING SAFETY DEFECTS WARNING! In The 50 United States And Washington, D.C. Engine exhaust (internal combustion engines only), If you believe that your vehicle has a defect that could some of its constituents, and certain vehicle compo- cause a crash or cause injury or death, you should nents contain, or emit, chemicals known to the State of immediately inform the National Highway Traffic...
Page 322: In Canada
320 CUSTOMER ASSISTANCE In Canada Diagnostic Procedure Manuals If you believe that your vehicle has a safety defect, you Diagnostic Procedure Manuals are filled with diagrams, should contact the Customer Service Department imme- charts and detailed illustrations. These practical manuals diately.
Page 323 INDEX...
Page 324 322 INDEX Adding Engine Coolant (Antifreeze) ... . .243 Antifreeze (Engine Coolant) ....242, 286 Adding Washer Fluid......233 Disposal .
Page 325 INDEX 323 Brake Control System, Electronic ....89 Cellular Phone ......306 Brake Fluid .
Page 326 324 INDEX Coolant Capacity ......286 Disposal Coolant Level ......242, 245 Antifreeze (Engine Coolant) .
Page 327 INDEX 325 Compartment ......232 Exterior Lights ......38, 133 Compartment Identification .
Page 328 326 INDEX Clean Air ......282 Hazard Ethanol .......283 Driving Through Flowing, Rising, Or Shallow Filler Cap (Gas Cap) .
Page 329 INDEX 327 Immobilizer (Sentry Key) ..... .20 Latches........134 Inside Rearview Mirror .
Page 330 328 INDEX Service ....... .179 Exterior Folding ......35 Tire Pressure Monitoring (TPMS) .
Page 331 INDEX 329 Viscosity ......235, 286 Pretensioners Oil Filter, Change ......236 Seat Belts .
Page 332 330 INDEX Restraints, Child ......123 Child Restraint ......123 Rotation, Tires .
Page 333 INDEX 331 Shoulder Belts ......102 Tire And Loading Information Placard... .254 Signals, Turn .
Page 334 332 INDEX Trailer Towing ......169 Trailer Towing Guide ......167 Tread Wear Indicators .
Page 335 INDEX 333 Warning Lights (Instrument Cluster Description) ..79 Warnings And Cautions ..... . .6 Warranty Information ..... . .319 Washer Adding Fluid .
Page 336 INSTALLATION OF RADIO TRANSMITTING The antenna cable should be as short as practical and EQUIPMENT routed away from the vehicle wiring when possible. Use Special design considerations are incorporated into this only fully shielded coaxial cable. vehicle’s electronic system to provide immunity to radio Carefully match the antenna and cable to the radio to frequency signals.

RAM Commercial 2018 PROMASTER Owner's Manual

Introduction

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

In Case of Emergency

Servicing and Maintenance

Technical Specifications

Multimedia

Customer Assistance

Quick Links

Chapters

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for RAM Commercial 2018 PROMASTER

Summary of Contents for RAM Commercial 2018 PROMASTER