Do you have a question about the PROMASTER 2017 and is the answer not in the manual?
Questions and answers
HERMAN SUMMERS
February 3, 2025
MY VAN WONT START BECAUSE OF THE ESC SAYS IT NEEDS SERVICED. IT STARTED WHEN I HAD IT PARKED ON A DECLINE AND WHEN IT DRIFTED DOWN AND I TURNED IT OFF IT WOULDNT START BACK UP. I WAS ABLE TO RESET IT ONCE BEFORE BY UNPLUGGING THE BATTERY AND WHEN I PARKE OD THE SAME HILL AND IT DRIFTED AGAIN I CANT SEEM TO DUPICATE THE RESTART. PLWEASE ADVISE
1 comments:
Mr. Anderson
February 10, 2025
If a 2017 RAM Commercial ProMaster won’t start due to ESC service requirements, consider the following steps:
1. Check the ESC Indicator Lights – If the “ESC Activation/Malfunction Indicator Light” remains on continuously while the engine is running, there may be a system malfunction.
2. Turn the Ignition Off and On – Restarting the vehicle may reset the ESC system. Ensure the ignition switch is in the ON position and check if the light turns off when the engine runs.
3. Drive the Vehicle – If the light remains on, drive the vehicle for several miles at speeds greater than 30 mph (48 km/h) to see if the issue resolves.
4. Listen for System Sounds – The ESC system may produce buzzing or clicking sounds when active. This is normal and indicates it is functioning properly.
5. Check for Power Reduction – If the vehicle is in “Partial Off” mode, the engine power reduction feature of the Traction Control System (TCS) is disabled, which may affect the ESC system.
6. Consult a Dealer – If the ESC malfunction light remains on after multiple ignition cycles and driving, contact an authorized dealer for diagnosis and repair.
These steps can help identify and possibly resolve ESC-related starting issues.
Summary of Contents for RAM Commercial PROMASTER 2017
Page 1
2 0 1 7 p r o m a s t e r O W N E R ’ S M A N U A L...
Page 2
VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name FCA features and equipment that are either standard or op- US LLC shall be deemed to be deleted and the name FCA tional on this vehicle.
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techni- Congratulations on selecting your new FCA US LLC ve- cians and genuine MOPAR® parts, and cares about your hicle. Be assured that it represents precision workmanship, satisfaction.
Page 7
INTRODUCTION 5 Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:...
6 INTRODUCTION WARNINGS AND CAUTIONS Operating instructions for the special equipment installed by the conversion/camper manufacturer should also be This Owner’s Manual contains WARNINGS against oper- supplied with your vehicle. If these instructions are miss- ating procedures that could result in a collision, bodily ing, please contact your authorized dealer for assistance in injury and/or death.
INTRODUCTION 7 VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATIONS The Vehicle Identification Number (VIN) is found on the WARNING! left front corner of the instrument panel, visible through the windshield. This number also appears on the vehicle Any modifications or alterations to this vehicle could frame and underbody as well as the Automobile Informa- seriously affect its roadworthiness and safety and may tion Disclosure Label affixed to a window on your vehicle,...
Page 11
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS ▫ To Unlock The Doors .....16 A WORD ABOUT YOUR KEYS ....11 ▫...
Page 12
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ Seat Belt Systems ..... . .22 ▫ Transporting Passengers ....51 ▫...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 A WORD ABOUT YOUR KEYS Mechanical Ignition Key Removal The key fob contains an integrated mechanical key. To use 1. Place the gear selector in PARK (if equipped with an the mechanical key, simply push the mechanical key re- automatic transmission).
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not leave children or animals inside parked • Before exiting a vehicle, always shift the automatic vehicles in hot weather. Interior heat build-up may transmission into PARK or the manual transmission cause serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 SENTRY KEY CAUTION! (Continued) The Sentry Key Immobilizer System prevents unauthor- • The Sentry Key Immobilizer system is not compat- ized vehicle operation by disabling the engine. The system ible with some aftermarket remote starting systems. does not need to be armed or activated.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information Rearming Of The System The following regulatory statement applies to all radio If the system has not been disabled, the vehicle security frequency (RF) devices equipped in this vehicle: alarm will rearm itself after the 15 additional minutes of turn lamps flashing.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 the vehicle or not. If you remain in the vehicle and open a REMOTE KEYLESS ENTRY (RKE) door, the alarm will sound. If this occurs, disarm the This system allows you to lock or unlock the doors from vehicle security alarm.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock The Doors Key Fob Battery Replacement Push and release the unlock button on key fob once to NOTE: Perchlorate Material – special handling may apply. unlock only the front doors. Push and release the cargo See www.dtsc.ca.gov/hazardouswaste/perchlorate unlock button on key fob once to unlock the cargo area The recommended replacement battery is CR2032.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 3. Take out the battery case. Remove and replace the POWER DOOR LOCKS battery observing its polarity. The central lock/unlock button has an LED that indicates whether the doors are locked or unlocked. 4.
Page 20
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The load compartment power door lock switch is located WARNING! (Continued) on the driver door trim panel. Use this switch to lock or • For personal security and safety in the event of a unlock the load compartment doors.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 WINDOWS CAUTION! Power Windows An unlocked vehicle is an invitation. Always remove The control on the left front door panel has up-down the key from the ignition and lock all of the doors switches that give you fingertip control of all power when leaving the vehicle unattended.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The power window switches remain active for up WARNING! to three minutes (depending on the accessory delay set- • Never leave children alone in a vehicle, or with ting) after the ignition switch has been turned OFF. Open- ing either of the vehicle’s front doors will cancel this access to an unlocked vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Some of the safety features described in this section may be restraints or belt-positioning booster seats should ride standard equipment on some models, or may be optional properly buckled up in a vehicle with a rear seat. equipment on others.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Seat Belt Use Reminder System (BeltAlert) WARNING! Driver And Passenger BeltAlert — If Equipped • Never place a rear-facing child restraint in front of an BeltAlert is a feature intended to remind the driver air bag.
Page 25
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 BeltAlert) (the outboard front passenger seat BeltAlert is pets be restrained in the rear seat (if equipped) in pet not active when the outboard front passenger seat is harnesses or pet carriers that are secured by seat belts, and unoccupied).
Page 26
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) or not an air bag is also provided at their seating • Relying on the air bags alone could lead to more position to minimize the risk of severe injury or severe injuries in a collision.
Page 27
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 WARNING! WARNING! (Continued) vehicle in a collision, increasing head and neck • A lap belt worn too high can increase the risk of injury. A seat belt worn under the arm can cause injury in a collision.
Page 28
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” 1. Enter the vehicle and close the door. Sit back and adjust the seat.
Page 29
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 4. Position the lap belt so that it is snug and lies low across 6. To release the seat belt, push the red button on the your hips, below your abdomen. To remove slack in the buckle.
Page 30
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the driver and front passenger seats, the top of the shoulder belt can be adjusted upward or downward to position the seat belt away from your neck. Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.
Page 31
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Seat Belts And Pregnant Women WARNING! • Wearing your seat belt incorrectly could make your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out of the seat belt.
Page 32
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioner Switchable Automatic Locking Retractor (ALR) The front seat belt system is equipped with pretensioning The seat belt in the passenger seating position is equipped devices that are designed to remove slack from the seat belt with a Switchable Automatic Locking Retractor (ALR) in the event of a collision.
Page 33
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 In Automatic Locking Mode, the shoulder belt is automati- cally pre-locked. The seat belt will still retract to remove any slack in the shoulder belt. Use the Automatic Locking Mode anytime a child restraint is installed in a seating position that has a seat belt with this feature.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Allow the seat belt to retract. As the seat belt retracts, Supplemental Restraint Systems (SRS) you will hear a clicking sound. This indicates the seat Some of the safety features described in this section may be belt is now in the Automatic Locking Mode.
Page 35
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 • Knee Impact Bolsters Warning Light will turn off. If the ORC detects a malfunc- tion in any part of the system, it turns on the Air Bag • Driver and Front Passenger Air Bags Warning Light, either momentarily or continuously.
Page 36
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the speedometer, tachometer, or any engine related gauges are not working, the Occupant Restraint Controller (ORC) may also be disabled. In this condition the air bags may not be ready to inflate for your protection. Have an authorized dealer service the air bag system immediately.
Page 37
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 WARNING! (Continued) WARNING! • Never place a rear-facing child restraint in front of an • No objects should be placed over or near the air bag air bag. A deploying passenger front air bag can on the instrument panel or steering wheel because cause death or serious injury to a child 12 years or any such objects could cause harm if the vehicle is in...
Page 38
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Front Air Bag Operation The steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as Front Air Bags are designed to provide additional protec- the air bags inflate to their full size.
Page 39
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Supplemental Side Air Bags The SABs may help to reduce the risk of occupant injury during certain side impacts, in addition to the injury Your vehicle is equipped with two types of supplemental reduction potential provided by the seat belts and body Side Air Bags: structure.
Page 40
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Supplemental Side Air Bag Inflatable Curtains SABICs inflate with enough force to injure occupants if (SABICs): Located above the side windows. The trim they are not belted and seated properly, or if items are positioned in the area where the SABICs inflate.
Page 41
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 The SABICs and SABs (Side Air Bags) are designed to WARNING! activate in certain side impacts. The Occupant Restraint • Occupants, including children, who are up against or Controller (ORC) determines whether the deployment of the Side Air Bags in a particular impact event is appropri- very close to Side Air Bags can be seriously injured ate, based on the severity and type of collision.
Page 42
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag System Components WARNING! • Occupant Restraint Controller (ORC) • Side Air Bags need room to inflate. Do not lean • Air Bag Warning Light against the door or window. Sit upright in the center •...
Page 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 If you do have a collision which deploys the air bags, any WARNING! or all of the following may occur: • The air bag material may sometimes cause abrasions Deployed air bags and seat belt pretensioners cannot protect you in another collision.
Page 44
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Flash hazard lights as long as the battery has power or until the hazard light button is pressed. The hazard lights can be deactivated by pressing the hazard light button. • Turn on the interior lights, which remain on as long as the battery has power.
Page 45
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Maintaining Your Air Bag System WARNING! (Continued) dealer. Only manufacturer approved seat accessories WARNING! may be used. If it is necessary to modify the air bag • Modifications to any part of the air bag system could system for persons with disabilities, contact your cause it to fail when you need it.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • These data can help provide a better understanding of Children 12 years or younger should ride properly buckled the circumstances in which crashes and injuries occur. up in a rear seat, if available. According to crash statistics, children are safer when properly restrained in the rear NOTE: EDR data are recorded by your vehicle only if a seats rather than in the front.
Page 47
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 • Canadian residents should refer to Transport Canada’s NOTE: website for additional information: • For additional information, refer to www.safercar.gov/ http://www.tc.gc.ca/eng/motorvehiclesafety/ parents/index.htm or call: 1–888–327–4236 safedrivers-childsafety-index-53.htm Summary Of Recommendations For Restraining Children In Vehicles Recommended Type Of Child Child Size, Height, Weight Or Age Restraint...
Page 48
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infant And Child Restraints WARNING! Safety experts recommend that children ride rear-facing in • Never place a rear-facing child restraint in front of an the vehicle until they are two years old or until they reach air bag.
Page 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 cushion while the child’s back is against the seatback, they Children Too Large For Booster Seats should use a belt-positioning booster seat. The child and Children who are large enough to wear the shoulder belt belt-positioning booster seat are held in the vehicle by the comfortably, and whose legs are long enough to bend over seat belt.
Page 50
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE position. If the shoulder belt contacts the face or neck, WARNING! move the child closer to the center of the vehicle, or use a booster seat to position the seat belt on the child correctly. Rear-facing infant restraints must never be secured in the passenger seat of a vehicle with a passenger Air WARNING!
Page 51
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 necessary to use a locking clip. The ALR retractor can be “switched” into a locked mode by pulling all of the webbing out of the retractor and then letting the webbing retract back into the retractor. If it is locked, the ALR will make a clicking noise while the webbing is pulled back into the retractor.
Page 52
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE back into the retractor. As the webbing retracts, you will WARNING! hear a clicking sound. This means the seat belt is now in • Improper installation or failure to properly secure a the Automatic Locking mode.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Transporting Pets under which vehicle operations will occur. For the recom- mended viscosity and quality grades, refer to “Mainte- Air Bags deploying in the front seat could harm your pet. nance Procedures” in “Maintaining Your Vehicle.” An unrestrained pet will be thrown about and possibly injured, or injure a passenger during panic braking or in a CAUTION!
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not run the engine in a closed garage or in • Do not leave children or animals inside parked confined areas any longer than needed to move your vehicles in hot weather.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Safety Checks You Should Make Inside The Vehicle Defroster Check operation by selecting the defrost mode and place Seat Belts the blower control on high speed. You should be able to Inspect the seat belt system periodically, checking for cuts, feel the air directed against the windshield.
Page 56
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) WARNING! (Continued) • ONLY use the passenger’s side floor mat on the Lightly pull to confirm mat is secured using the floor mat fasteners on a regular basis. passenger’s side floor area. •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Periodic Safety Checks You Should Make Outside Door Latches The Vehicle Check for proper closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Outside Mirrors To receive maximum benefit, adjust the outside mirror(s) to Inside Day/Night Mirror — If Equipped center on the adjacent lane of traffic with a slight overlap of A two-point pivot system allows for horizontal and vertical the view obtained on the inside mirror.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 61 Power Mirrors — If Equipped To adjust a mirror, turn the control knob toward the left upper, left lower, right upper or right lower mirror posi- The power mirror controls are located on the driver-side tions indicated by one of the four arrow’s on the switch.
62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Folding Mirrors — If Equipped The switch for the power folding mirrors is located on the driver’s door panel below the power mirror controls. Power Folding Mirror Switch 1 — Power Folding Mirror (Normal Driving Position) 2 —...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 63 NOTE: The intended use of the power fold mirrors is by CAUTION! pushing the buttons to fold and unfold the mirrors. Only manually fold the mirrors when necessary. Leaving the mirror in a non powered position, acciden- tal impact or manual fold, may cause permanent dam- Forward Folding age to the mirror.
64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Front Seat Adjustments Lumbar Support — If Equipped The driver and passenger seats can be adjusted forward/ This feature allows you to increase or decrease the amount rearward and reclined. Also, if equipped, front and rear of lumbar support.
Page 67
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65 Height Adjustment (Without Swivel Seat) — If Equipped Height Adjustment (With Swivel Seat) — If Equipped The height adjusting levers are located on the center The height adjusting knobs are located on the center outboard side of the seat.
Page 68
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Recliner Adjustment — Without Swivel Seat Recliner Adjustment — With Swivel Seat The recliner knob is on the rear outboard side of the seat. To The recliner lever is located at the lower front outboard recline the seatback, lean back, rotate the knob rearward to side of the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 67 Damper Weight Adjustment WARNING! Use the weight adjustment knob to set the required setting • Adjusting a seat while the vehicle is moving is based on body weight, with settings between 88 lbs (40 kg) dangerous.
68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Swivel Seat — If Equipped If the driver or the passenger seats are not locked in facing forward position before the first vehicle movement, shift- The swivel seat lever is located at the lower front inboard ing out of park is not allowed until the seats are both side of the seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 69 Flap On Bench — If Equipped The fold-down flap is equipped with two cup holders and a support surface with a paper holder clip. If your vehicle is equipped with a bench seat, the seat is equipped with a fold-down flap that can be used as a document support surface.
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Underseat Storage Tray (Driver Side Only) — If Heated Seats — If Equipped Equipped On some models, the front driver and passenger seats may A storage tray is located under the driver’s seat that can be be equipped with heaters in both the seat cushions and easily removed by withdrawing the hooks on the support seatbacks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 WARNING! WARNING! • Persons who are unable to feel pain to the skin • All occupants, including the driver, should not oper- because of advanced age, chronic illness, diabetes, ate a vehicle or sit in a vehicle’s seat until the head spinal cord injury, medication, alcohol use, exhaus- restraints are placed in their proper positions in tion or other physical condition must exercise care...
Page 74
72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To remove the head restraint, raise it up as far as it can go. WARNING! Then, push the adjustment button and the release button at • A loose head restraint thrown forward in a collision the base of each post while pulling the head restraint up.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 Adjustable Armrests — If Equipped Turn the adjuster wheel to the right or left to adjust the height of the armrest up or down. The seat adjustable armrest can be raised and adjusted for height.
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD 2. Move to the outside of the vehicle, reach into the opening beneath the center of the hood and push the To open the hood, two latches must be released. safety latch lever to the right to release it, before raising 1.
Page 77
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 3. Raise the hood and place the hood prop rod in hood slot CAUTION! to secure the hood in the open position. To prevent possible damage: • Before closing hood, make sure the hood prop rod is fully seated into its storage retaining clips.
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Headlights To turn on the headlights, turn the end of the Multifunction Lever multifunction lever to the headlight position. The multifunction lever controls the operation of the When the headlight switch is on, the parking headlights, parking lights, turn signals, headlight beam lights, taillights, license plate light, the clearance selection and the passing lights.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Pushing the up or down arrow will increase or decrease the Battery Saver brightness of the instrument panel lights. To protect the life of your vehicle’s battery when the ignition is OFF and any door is left ajar for 15 minutes the Ambient Light interior lights will automatically turn off.
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If either light remains on and does not flash, or Flash-To-Pass there is a very fast flash rate, check for a defective outside You can signal another vehicle with your headlights by light bulb.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Deactivation Pull the multifunction lever toward the steering wheel and hold it for more than two seconds. Overhead Lights These lights are mounted between the sun visors on the overhead shelf. Each light is turned on by pushing the corresponding switch.
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dome Lights Ambient Light The interior lights can be set to three different positions The vehicle is equipped with ambient light on the dome (Off/Left Position, Center Position, On/Right Position). lamp, the ambient light will be on all the time with the Using the switch on the bottom of the overhead console: option of dimming it with the dimmer controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 WINDSHIELD WIPERS AND WASHERS Windshield Wipers The windshield wiper/washer lever is located on the right side of the steering column. There are five different modes of operation for the front windshield wipers. The wind- shield wiper lever can be raised or lowered to access the modes.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Windshield Washer Operation Push the lever downward to the first detent and rotate the To use the washer, pull the windshield wiper/washer lever center ring to use one of the four intermittent wiper toward the steering wheel to activate the washers.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 WARNING! (Continued) driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. SPEED CONTROL When engaged, the Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h) up to the maximum speed of 100 mph (160 km/h).
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Speed To Set A Desired Speed Control System has been designed to shut down if multiple Turn the Speed Control ON. When the vehicle has reached Speed Control functions are operated at the same time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 To Vary The Speed Setting To Decrease Speed To Increase Speed When the Speed Control is set, you can decrease speed by tapping the Speed Control lever down (-). When the Speed Control is set, you can increase speed by tapping the Speed Control lever up (+).
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing PARKSENSE REAR PARK ASSIST — IF EQUIPPED Press the accelerator as you would normally. When the The ParkSense Rear Park Assist system provides an au- pedal is released, the vehicle will return to the set speed. dible indication of the distance between the rear fascia/ bumper and a detected obstacle when backing up, e.g.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 ParkSense Rear Park Assist Sensors If several obstacles are detected, the ParkSense Rear Park Assist system indicates the nearest obstacle. The four ParkSense Rear Park Assist sensors, located in the rear fascia/bumper, monitor the area behind the vehicle The minimum height of a detectable obstacle corresponds that is within the sensors’...
Page 90
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Audible And Visual Signals Supplied By The ParkSense Rear Park Assist System SIGNAL MEANING INDICATION Obstacle Distance An obstacle is present within the Audible signal (dashboard loud- sensors’ field of view speaker) • Sound pulses emitted at a rate that increases as the distance decreases.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 ParkSense Rear Park Assist Failure Indications inches (10 cm) from the sensors. Do not scratch or poke the sensors. Otherwise, you could damage the sensors. A malfunction of the ParkSense Rear Park Assist sensors or system is indicated, during REVERSE gear engagement, by ParkSense Rear Park Assist System Usage the instrument panel warning icon.
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE problem, causing a failure indication to be displayed in CAUTION! the instrument cluster display. • ParkSense is only a parking aid and it is unable to WARNING! recognize every obstacle, including small obstacles. Parking curbs might be temporarily detected or not •...
Page 93
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 selector is put into REVERSE and/or when the rear doors When the vehicle is shifted out of REVERSE and/or when are opened. The image will be displayed on the touch- the rear doors are closed, the rear camera mode is exited screen display along with a caution note to “check entire and the navigation or audio screen appears again.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: ParkView Rear Back Up Camera can be enabled or NOTE: If snow, ice, mud, or any foreign substance builds disabled by Uconnect system menu. up on the camera lens, clean the lens, rinse with water, and dry with a soft cloth.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 POWER OUTLETS — IF EQUIPPED Load Compartment Power Outlet Passenger Compartment Power Outlet The Load Compartment Power Outlet is located on the left rear side of the rear cargo compartment. The outlet can be The cigar lighter and the power outlet are located in the is used for powering 12 Volt adaptive accessories and center console.
Page 96
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Do not connect devices with power higher than 180 WARNING! W to the socket. Do not damage the socket by using unsuitable adaptors. To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 CAUTION! (Continued) • After the use of high power draw accessories, or long periods of the vehicle not being started (with acces- sories still plugged in), the vehicle must be driven a sufficient length of time to allow the generator to recharge the vehicle’s battery.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS STORAGE The cupholders for the driver’s and passenger’s area are Glove Compartments located near the floor just under the center stack storage The glove compartments are located on the right side of the compartment.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Front Door Storage — If Equipped Dash Storage Storage areas and bottle holders are located in both the The dash storage is located on the right side of the front door trim panels. instrument panel.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dashboard Clipboard CARGO AREA FEATURES Located on top of the dashboard is a clipboard and two Cargo Area storage bins on each side of the clipboard. The cargo area may be equipped with different options such as a optional side panels, rear seats and an optional floor.
Page 101
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS ▫ Values Displayed ..... . .128 INSTRUMENT PANEL FEATURES ...101 ▫...
102 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER 1. Speedometer “Instrument Cluster Display” in “Understanding Your • Indicates vehicle speed. Instrument Panel” for further information. • Odometer/Trip Odometer Display Area 2. Instrument Cluster Display U.S. Federal regulations require that upon transfer of •...
Page 105
UNDERSTANDING YOUR INSTRUMENT PANEL 103 the correct mileage that the vehicle has been driven. If 4. Temperature Gauge your odometer needs to be repaired or serviced, the • The temperature gauge shows engine coolant tem- repair technician should leave the odometer reading perature.
104 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING AND INDICATOR LIGHTS CAUTION! The warning/indicator lights switch on in the instrument Driving with a hot engine cooling system could dam- panel together with a dedicated message and/or acoustic age your vehicle. If the temperature gauge reads “H” signal when applicable.
UNDERSTANDING YOUR INSTRUMENT PANEL 105 Red Telltale Indicator Lights Seat Belt Reminder Warning Light Red Telltale What It Means Light Seat Belt Reminder Warning Light When the ignition is first placed in the ON/RUN position, if the driver’s seat belt is unbuckled, a chime will sound and the light will turn on.
Page 108
106 UNDERSTANDING YOUR INSTRUMENT PANEL Battery Charge Warning Light Red Telltale What It Means Light Battery Charge Warning Light This light illuminates when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact your authorized dealer as soon as possible.
Page 109
UNDERSTANDING YOUR INSTRUMENT PANEL 107 Electronic Throttle Control (ETC) Warning Light Red Telltale What It Means Light Electronic Throttle Control (ETC) Warning Light This light informs you of a problem with the Electronic Throttle Control (ETC) system. If a prob- lem is detected while the engine is running, the light will either stay on or flash depending on the nature of the problem.
Page 110
108 UNDERSTANDING YOUR INSTRUMENT PANEL Transmission Fault Warning Light Red Telltale What It Means Light Transmission Fault Warning Light This light will illuminate (together with a message in the instrument cluster display and a buzzer) to indicate a transmission fault. This light indicates that the transmission fluid tempera- ture is running hot.
Page 111
UNDERSTANDING YOUR INSTRUMENT PANEL 109 Coolant Temperature Warning Light Red Telltale What It Means Light Coolant Temperature Warning Light This light warns of an overheated engine condition. If the light turns on while driving, safely pull over and stop the vehicle. If the A/C system is on, turn it off. Also, shift the transmission into NEUTRAL and idle the vehicle.
Page 112
110 UNDERSTANDING YOUR INSTRUMENT PANEL Brake Warning Light Red Telltale What It Means Light Brake Warning Light This light monitors various brake functions, including brake fluid level and parking brake appli- cation. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the anti-lock brake system reservoir.
Page 113
UNDERSTANDING YOUR INSTRUMENT PANEL 111 Operation of the Brake Warning Light can be checked by WARNING! placing the ignition in the ON/RUN position. The light should illuminate for approximately two seconds. The light Driving a vehicle with the red brake light on is should then turn off unless the parking brake is applied or dangerous.
112 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Pressure Warning Light Red Telltale What It Means Light Oil Pressure Warning Light This light indicates low engine oil pressure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected.
Page 115
UNDERSTANDING YOUR INSTRUMENT PANEL 113 External Light Failure Indicator Light — If Equipped Yellow Telltale What It Means Light External Light Failure Indicator Light — If Equipped The External Light Failure Indicator will come on when a failure to one of the following lights is detected: •...
Page 116
114 UNDERSTANDING YOUR INSTRUMENT PANEL Vehicle Security Indicator Light Yellow Telltale What It Means Light Vehicle Security Indicator Light If during starting, the key code is not correctly recognized, the vehicle security light comes on in the instrument panel. In this case, turn the key to OFF and then to ON/RUN; if it is still locked, try again with the other keys that come with the vehicle.
Page 117
UNDERSTANDING YOUR INSTRUMENT PANEL 115 that illuminates a low tire pressure telltale when one or CAUTION! more of your tires is significantly under-inflated. Accord- ingly, when the low tire pressure telltale illuminates, you Do not continue driving with one or more flat tires as should stop and check your tires as soon as possible, and handling may be compromised.
Page 118
116 UNDERSTANDING YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a TPMS malfunc- CAUTION! tion indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined The TPMS has been optimized for the original equip- with the low tire pressure telltale.
Page 119
UNDERSTANDING YOUR INSTRUMENT PANEL 117 Electronic Stability Control (ESC) Activation/Malfunction Indicator Light Yellow Telltale What It Means Light Electronic Stability Control (ESC) Activation/Malfunction Indicator Light The “ESC Activation/Malfunction Indicator Light” in the instrument cluster will come on when the ignition is placed in the ON/RUN position. It should go out with the engine running. If the “ESC Activation/Malfunction Indicator Light”...
Page 120
118 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Stability Control (ESC) OFF Indicator Light Yellow Telltale What It Means Light Electronic Stability Control (ESC) OFF Indicator Light This light indicates the Electronic Stability Control (ESC) is off. For further information, refer to “Electronic Stability Control (ESC)”...
Page 121
UNDERSTANDING YOUR INSTRUMENT PANEL 119 WARNING! CAUTION! A malfunctioning catalytic converter, as referenced Prolonged driving with the Malfunction Indicator above, can reach higher temperatures than in normal Light (MIL) on could cause damage to the engine operating conditions. This can cause a fire if you drive control system.
Page 122
120 UNDERSTANDING YOUR INSTRUMENT PANEL Anti-Lock Brake (ABS) Indicator Light Yellow Telltale What It Means Light Anti-Lock Brake (ABS) Indicator Light This light monitors the Anti-Lock Brake System (ABS). The light will turn on when the ignition is placed in the ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required.
UNDERSTANDING YOUR INSTRUMENT PANEL 121 Green Telltale Indicator Lights Turn Signal Indicator Lights Green Telltale What It Means Light Turn Signal Indicator Lights The instrument cluster directional arrow will flash independently for the left or right turn signal as selected, as well as the exterior turn signal lamp(s) (front and rear) as selected when the multi- function lever is moved down (left) or up (right).
Page 124
122 UNDERSTANDING YOUR INSTRUMENT PANEL Park/Headlight On Indicator Light Green Telltale What It Means Light Park/Headlight On Indicator Light This indicator will illuminate when the park lights or headlights are turned on. Cruise Control Engaged Indicator Light — If Equipped Green Telltale What It Means Light...
UNDERSTANDING YOUR INSTRUMENT PANEL 123 Blue Telltale Indicator Lights High Beam Indicator Light Blue Telltale What It Means Light High Beam Indicator Light This indicator shows that the high beam headlights are on. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever toward you to switch the headlights back to low beam.
124 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Date Instrument Cluster Display And Controls • Autoclose The instrument cluster display features a driver-interactive display that is located in the instrument cluster. • Units • Language • Buzzer Volume • Seat Belt Buzzer (Just Available After SBR Disable Made By CHR Service) •...
UNDERSTANDING YOUR INSTRUMENT PANEL 125 • Up Arrow Button The system allows the driver to select information by pushing the following buttons mounted on the instrument Push and release the up arrow button to scroll panel to the left of the steering column: upward through the main menu and submenus or adjust the illumination on the instrument panel when the headlights are on.
Page 128
126 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Data Selecting An Option Of The Main Menu Without Submenu • Autoclose 1. Briefly push and release the MODE button to select the main menu option to set. • Units (Distance, Fuel Economy, Temperature) 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 127 6. Push and release and hold the MODE button to return NOTE: If the indicator message illuminates when you to the main menu (short hold) or the main screen (longer start the vehicle, the oil change indicator system did not hold).
128 UNDERSTANDING YOUR INSTRUMENT PANEL • Disconnecting/Reconnecting the battery resets the sys- • Average Speed A tem. • Travel Time A (Driving Time) NOTE: If the reset operation occurs in the presence of the “Trip B” can be used to display the figures relating to: screens concerning Trip A or Trip B, only the information •...
UNDERSTANDING YOUR INSTRUMENT PANEL 129 • The vehicle is parked for a long time with the engine Travel Time running. This value shows the time elapsed since the last reset. NOTE: The range depends on several factors: driving Personal Settings (Customer-Programmable style, type of route (freeway, residential, mountain roads, Features) etc.), and conditions of use of the vehicle (load, tire...
130 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: updates to improve the usability and performance of your systems or to reduce the potential risk of unauthorized and • If equipped with Uconnect 5.0/5.0N radio, some cus- unlawful access to your vehicle systems. tomer programmable features will display in the Uconnect 5.0/5.0N system.
UNDERSTANDING YOUR INSTRUMENT PANEL 131 UCONNECT RH3 WARNING! (Continued) Introduction • As always, if you experience unusual vehicle behav- ior, take your vehicle to your nearest authorized Your vehicle is equipped with a radio that has an AM/FM dealer immediately. radio receiver and a USB port for playing MP3, WMA and AAC files.
132 UNDERSTANDING YOUR INSTRUMENT PANEL Recommendations Care And Maintenance The radio structure is built to guarantee many years of Road Safety operation without needing maintenance. In case of a fault, We recommend that you learn how to use the various radio contact your local authorized dealer.
UNDERSTANDING YOUR INSTRUMENT PANEL 133 You must enter the security (shown on the warranty card , If you enter the correct code, the radio will start as normal for example, 4359) code as follows: in radio mode (TUNER). If you enter the wrong code, the radio will remain locked until disconnected from the Action Display...
134 UNDERSTANDING YOUR INSTRUMENT PANEL General Uconnect RH3 Display • Separate BASS and TREBLE settings • BALANCE/FADE (balances left/right and front/rear channels) • Equalizer • Loudness • Digital clock in 24-hour format with weekday setting • Illuminated buttons and display •...
UNDERSTANDING YOUR INSTRUMENT PANEL 135 DISP Button: Switches between display modes, clock The default radio configuration is “Auto Switch ON (see display. SETUP MENU section). In this configuration, the radio will follow two parameters: ignition and previous state. If the RND Button: Enables/Disables shuffle play.
Page 138
136 UNDERSTANDING YOUR INSTRUMENT PANEL Equalizer Bass Pushing the AUDIO button for more than two seconds The display will show BASS 00 to indicate that the Bass activates the audio equalizer functions in the following function can be set. To increase the bass level, turn the sequence: FLAT ROCK CLASSIC...
UNDERSTANDING YOUR INSTRUMENT PANEL 137 Fader In this mode of operation the display will show one of the following 5 codes: The display will show FAD 00 to indicate that you can set CH (Channel) the Fader function. Turn the ROTARY knob clockwise to transfer the sound to the front;...
Page 140
138 UNDERSTANDING YOUR INSTRUMENT PANEL Searching for Stations In Manual Mode When the , Audio, 1, 2, 3, 4, 5, 6, BAND/AS buttons and SRC are pushed in Mute/Paused mode, Pushing for more than two seconds displays these will be implemented and the audio will be re- the selected radio station frequency.
UNDERSTANDING YOUR INSTRUMENT PANEL 139 associated with that particular memory location. The dis- be allocated to the 107.9 MHz frequency for FM and AM play shows the preset number and frequency of the asso- 1710 KHz for the AM band. At the end of the search ciated station for three seconds.
140 UNDERSTANDING YOUR INSTRUMENT PANEL indicating the maximum volume selected. When the maxi- radio is off. This function takes priority in the display mum volume selected is the maximum radio volume, the whenever you access any of the radio functions. If no display will show MVOL OFF .
Page 143
UNDERSTANDING YOUR INSTRUMENT PANEL 141 In USB mode, the radio plays MP3, WMA and AAC files If playable files are found, the radio will also check that the stored on the device connected to the USB port that is connected device is the same as the one used immediately located on the lower right side of the steering wheel on the before the USB function.
Page 144
142 UNDERSTANDING YOUR INSTRUMENT PANEL File Sequence...
Page 145
UNDERSTANDING YOUR INSTRUMENT PANEL 143 Play Sequence (File) Comments Track 1_1 If there are MP3, WMA or AAC (extensions mp3, wma, m4a, mp4 and 3gp) files in the root folder, these will be played first. Track 2_1 Folders within the same level are sorted in ascending order by name (up to folder number 100, after which the order follows that in which they were recorded on the Track 3_1 USB device).
Page 146
144 UNDERSTANDING YOUR INSTRUMENT PANEL name of the folder you are moving to for at least 500 ms Push this button again to resume music playback from the (seek button movements are ignored during this time), point where it left off, without changing the original and no longer than three seconds.
Page 147
UNDERSTANDING YOUR INSTRUMENT PANEL 145 counterclockwise will reverse the tracks. While this is being Forward/Reverse Folder performed, the information contained in the ID3 tag is not When you push the memory 1 button, the radio will processed. As the knob is turned, the TRKyyy message advance to the first track in the next folder containing changes to the track selected.
146 UNDERSTANDING YOUR INSTRUMENT PANEL Shuffle (Random Playback) the button, the display now shows the information type related to the track being played, for example, if the Pushing the RND button enables or disables the shuffle current information is track, the display will show feature.
UNDERSTANDING YOUR INSTRUMENT PANEL 147 CAUTION! Do NOT attach any object to the touchscreen, doing so can result in damage to the touchscreen. Uconnect 5.0 NAV Buttons On The Touchscreen And Buttons On The Faceplate 1 — Uconnect Buttons On The Touchscreen 2 —...
148 UNDERSTANDING YOUR INSTRUMENT PANEL Your Uconnect system may also have a power and back NOTE: buttons on the faceplate. • Only one category may be selected at a time. Push the power button on the faceplate to turn off the •...
Page 151
UNDERSTANDING YOUR INSTRUMENT PANEL 149 Setting Name Selectable Options Display Mode Manual Auto Display Brightness With Up Arrow Button Down Arrow Button Headlights ON NOTE: This feature is only available in Manual Display Mode. Display Brightness With Up Arrow Button Down Arrow Button the Headlights Off NOTE: This feature is only available in Manual Display Mode.
Page 152
150 UNDERSTANDING YOUR INSTRUMENT PANEL Clock & Date After pressing the “Clock & Date” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Set Time And For- mat — If Equipped Show Time Statues —...
Page 153
UNDERSTANDING YOUR INSTRUMENT PANEL 151 Safety/Assistance After pressing the “Safety/Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options ParkView Rear Backup Camera Ac- tive Guide Lines — If Equipped NOTE: The “ParkView Backup Camera Active Guide Lines” setting overlays the Rear Backup Camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its project back up path, based on the steering wheel position when the option is checked.
Page 154
152 UNDERSTANDING YOUR INSTRUMENT PANEL Lights After pressing the “Lights” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Daytime Running Lights — If Equipped NOTE: When the “Daytime Running Lights” feature is selected, the headlights will turn on whenever the engine is running.
Page 155
UNDERSTANDING YOUR INSTRUMENT PANEL 153 Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Equalizer – NOTE: When in this display you may adjust the “Bass”, “Mid” and “Treble” settings. Adjust the settings with the “+”...
Page 156
154 UNDERSTANDING YOUR INSTRUMENT PANEL Setting Name Selectable Options Surround Sound — If Equipped Loudness — If Equipped NOTE: The “Loudness” feature improves sound quality at lower volumes when enabled. Auto - On Radio Last Recall NOTE: Press the “Auto - On Radio” button on the touchscreen to set how the radio behaves when the Ignition is switched to ON.
Page 157
UNDERSTANDING YOUR INSTRUMENT PANEL 155 SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music channel using one of the twelve presets, so you can enjoy the complete song.
Page 158
156 UNDERSTANDING YOUR INSTRUMENT PANEL Setting Name Selectable Options Subscription Info Sirius ID NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe.
UNDERSTANDING YOUR INSTRUMENT PANEL 157 IPOD/USB/MP3 CONTROL — IF EQUIPPED For further information, refer to the Uconnect Owner’s Manual Supplement. The USB Port and Auxiliary Jack is located on the instru- ment panel left of the radio (driver’s lower right). This USB Charging Port feature allows an iPod or external USB device to be The USB connector port can be used for charging purposes...
158 UNDERSTANDING YOUR INSTRUMENT PANEL The right-hand control is a rocker-type switch and controls WARNING! the SCAN functions of the sound system. Do not plug in or remove the iPod or external device The left-hand control is a rocker-type switch and controls while driving.
UNDERSTANDING YOUR INSTRUMENT PANEL 159 4. Do not use solvents such as benzene, thinner, cleaners, harmful to the radio. If your radio performance does not or anti-static sprays. satisfactorily “clear” by the repositioning of the phone, it is recommended that the radio volume be turned down or off 5.
160 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS The Manual Temperature Controls consist of a series of three outer rotary dials (blower speed, temperature and The Climate Control System allows you to regulate the mode) and three inner push buttons (Recirculation, A/C, temperature, airflow, and direction of air circulating Rear Window Defroster).
Page 163
UNDERSTANDING YOUR INSTRUMENT PANEL 161 Manual Climate Control Descriptions Icon Description A/C Button Push the A/C button to engage the Air Conditioning (A/C). A LED will illuminate when the A/C system is engaged. Recirculation Button Press and release this button to change the system between recirculation mode and outside air mode.
Page 164
162 UNDERSTANDING YOUR INSTRUMENT PANEL Icon Description Rear Defrost Button Push and release the Rear Defrost Control button to turn ON the rear window defroster and the heated outside mirrors (if equipped). An indicator will illuminate when the rear window de- froster is ON.
Page 165
UNDERSTANDING YOUR INSTRUMENT PANEL 163 Icon Description Panel Mode Panel Mode Air comes from the outlets in the instrument panel. Each of these outlets can be individually adjusted to direct the flow of air. The air vanes of the center outlets and outboard outlets can be moved up and down or side to side to regulate airflow direction.
Page 166
164 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear win- dow. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heat- ing elements.
UNDERSTANDING YOUR INSTRUMENT PANEL 165 NOTE: NOTE: In cold weather, use of recirculation mode may lead to excessive window fogging. The recirculation feature • If fog or mist appears on the windshield or side glass, may be unavailable (button on the touchscreen greyed out) select Defrost mode and increase blower speed if if conditions exist that could create fogging on the inside of needed.
Page 168
166 UNDERSTANDING YOUR INSTRUMENT PANEL Winter Operation Outside Air Intake Use of the air Recirculation mode during winter months is Make sure the air intake, located directly in front of the not recommended because it may cause window fogging. windshield, is free of obstructions such as leaves. Leaves collected in the air intake may reduce airflow, and if they Vacation Storage enter the plenum, they could plug the water drains.
Page 169
UNDERSTANDING YOUR INSTRUMENT PANEL 167 Control Setting Suggestions For Various Weather Conditions Control Settings Suggestions For Various Weather Conditions Chart...
168 UNDERSTANDING YOUR INSTRUMENT PANEL UCONNECT VOICE RECOGNITION Introducing Uconnect Start using Uconnect Voice Recognition with these helpful quick tips. It provides the key Voice Commands and tips you need to know to control your Uconnect system. Uconnect 5.0 Get Started 1.
Page 171
UNDERSTANDING YOUR INSTRUMENT PANEL 169 3. Speak clearly at a normal pace and volume while facing straight ahead. The microphone is positioned in the dome lamp and aimed at the driver. 4. Each time you give a Voice Command, you must first push either the VR or PHONE button, wait until after the beep, then say your Voice Command.
170 UNDERSTANDING YOUR INSTRUMENT PANEL Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say • Cancel to stop a current voice session •...
UNDERSTANDING YOUR INSTRUMENT PANEL 171 TIP: At any time, if you are not sure of what to say or want Media to learn a Voice Command, push the VR button and say Uconnect offers connections via USB, Bluetooth and Aux- Help.
172 UNDERSTANDING YOUR INSTRUMENT PANEL TIP: Press the “Browse” button on the touchscreen to see Push the Phone button . After the beep, say one of the all of the music on your iPod or USB device. Your Voice following commands Command must match exactly how the artist, album, song •...
UNDERSTANDING YOUR INSTRUMENT PANEL 173 PRE-DEFINED VOICE TEXT REPLY RESPONSES Yes. Stuck in traffic. See you later. Start without I’ll be late. Okay. Where are you? I will be <num- ber> minutes Call me. Are you there late. yet? I’ll call you later. I need direc- See you in tions.
178 STARTING AND OPERATING STARTING PROCEDURES Normal Starting Before starting your vehicle, adjust your seat, adjust both NOTE: Normal starting of either a cold or a warm engine inside and outside mirrors, and fasten your seat belts. is obtained without pumping or pressing the accelerator pedal.
STARTING AND OPERATING 179 CAUTION! WARNING! • Do not attempt to push or tow your vehicle to get it Remember to disconnect the engine block heater cord started. Vehicles equipped with an automatic trans- before driving. Damage to the 110-115 Volt electrical mission cannot be started this way.
180 STARTING AND OPERATING WARNING! (Continued) CAUTION! (Continued) • Do not shift between PARK, REVERSE, NEUTRAL, Once the key is removed, the transmission is locked in PARK, securing the vehicle against unwanted or DRIVE when the engine is above idle speed. •...
STARTING AND OPERATING 181 transmission out of PARK, the ignition must be turned to the ON/RUN mode (engine running or not), and the brake pedal must be pressed. NOTE: Swivel seats that are unlocked can also prevent the transmission gear selector from being moved out of the PARK position.
Page 184
182 STARTING AND OPERATING upshifts beyond this gear. In ERS mode, toggling the gear When parking on a level surface, you may shift the transmis- selector forward (-) or rearward (+) will change the highest sion into PARK first, and then apply the parking brake. available gear.
Page 185
STARTING AND OPERATING 183 WARNING! (Continued) WARNING! (Continued) • Never leave children alone in a vehicle, or with selector out of PARK with the brake pedal released. Make sure the transmission is in PARK before leav- access to an unlocked vehicle. Allowing children to ing the vehicle.
Page 186
184 STARTING AND OPERATING CAUTION! WARNING! • Before moving the transmission gear selector out of Do not coast in NEUTRAL and never turn off the PARK, you must turn the ignition to the ON/RUN ignition to coast down a hill. These are unsafe practices mode, and also press the brake pedal.
Page 187
STARTING AND OPERATING 185 When frequent transmission shifting occurs (such as when result in transmission damage, Transmission Limp Home operating the vehicle under heavy loading conditions, in Mode is activated. In this mode, the transmission remains hilly terrain, traveling into strong head winds, or while in third gear regardless of which forward gear is selected.
Page 188
186 STARTING AND OPERATING NOTE: Even if the transmission can be reset, we recom- the ERS position (beside DRIVE) will activate ERS mode, mend that you visit your authorized dealer at your earliest display the current gear in the instrument cluster, and set possible convenience.
Page 189
STARTING AND OPERATING 187 NOTE: To select the proper gear position for maximum potential for transmission overheating or failure due to deceleration (engine braking), move the gear selector into excessive shifting. When operating in TOW/HAUL mode, the ERS position, then tap it forward (-) repeatedly as the transmission upshifts are delayed, and the transmission vehicle slows.
188 STARTING AND OPERATING NOTE: right or left. This phenomenon occurs when there is a differ- ence in the surface traction under the front (driving) wheels. • The torque converter clutch will not engage, until the transmission fluid and engine coolant are warm [usually WARNING! after 1 to 3 miles (2 to 5 km) of driving].
STARTING AND OPERATING 189 4. Keep tires properly inflated. Shallow Standing Water Although your vehicle is capable of driving through shal- 5. Maintain sufficient distance between your vehicle and low standing water, consider the following Cautions and the vehicle in front of you to avoid a collision in a Warnings before doing so.
190 STARTING AND OPERATING POWER STEERING CAUTION! The standard power steering system will give you good • Always check the depth of the standing water before vehicle response and increased ease of maneuverability in driving through it. Never drive through standing tight spaces.
STARTING AND OPERATING 191 CAUTION! CAUTION! Prolonged operation of the steering system at the end Do not use chemical flushes in your power steering of the steering wheel travel will increase the steering system as the chemicals can damage your power steer- fluid temperature and it should be avoided when ing components.
Page 194
192 STARTING AND OPERATING The parking brake lever is located on the outboard side of When parking on a hill, it is important to turn the front the drivers seat. To apply the parking brake, pull the lever wheels toward the curb on a downhill grade and away up as firmly as possible.
STARTING AND OPERATING 193 will still function. However, the effort required to brake the WARNING! (Continued) vehicle will be much greater than that required with the injury. Also be certain to leave a manual transmis- power system operating. sion in FIRST gear or REVERSE gear. Failure to do so may allow the vehicle to roll and cause damage or ELECTRONIC BRAKE CONTROL SYSTEM injury.
194 STARTING AND OPERATING reverts to standard non-anti-lock brakes. Turning the igni- When you are in a severe braking condition involving the tion Off and On again may reset the ABS if the fault use of the ABS, you will experience some pedal drop as the detected was only momentary.
STARTING AND OPERATING 195 that the TCS is active. If the indicator light flashes during the ABS. Applying the brakes very quickly results in the acceleration, ease up on the accelerator and apply as little best BAS assistance. To receive the benefit of the system, throttle as possible.
Page 198
196 STARTING AND OPERATING assist in counteracting the over/under steer condition. WARNING! (Continued) Engine power may also be reduced to help the vehicle hydroplaning. ESC also cannot prevent accidents re- maintain the desired path. sulting from loss of vehicle control due to inappropri- ESC uses sensors in the vehicle to determine the vehicle ate driver input for the conditions.
Page 199
STARTING AND OPERATING 197 ESC Partial Off WARNING! (Continued) This mode is entered by momentarily pushing the “ESC • Trailer Sway Control (TSC) is disabled when the ESC Off” switch. system is in the Partial Off mode. When in the “Partial Off” mode, the TCS portion of ESC, NOTE: To improve the vehicle’s traction when driving except for the “limited slip”...
198 STARTING AND OPERATING • The ESC system will make buzzing or clicking sounds speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible to have the problem diagnosed when it is active. This is normal; the sounds will stop and corrected.
STARTING AND OPERATING 199 • Vehicle must be on a 6% (approximate) grade or greater to attempt to stop the trailer from swaying. TSC is disabled when the ESC system is in the “Partial Off” mode. hill. • Gear selection matches vehicle uphill direction (i.e., WARNING! vehicle facing uphill is in forward gear;...
200 STARTING AND OPERATING TIRE SAFETY INFORMATION WARNING! Tire Markings • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object...
Page 203
STARTING AND OPERATING 201 • European — Metric tire sizing is based on European • Temporary spare tires are designed for temporary emer- design standards. Tires designed to this standard have gency use only. Temporary high pressure compact spare the tire size molded into the sidewall beginning with the tires have the letter “T”...
Page 204
202 STARTING AND OPERATING EXAMPLE: R = Construction code – R means radial construction, or – D means diagonal or bias construction 15, 16, 18 = Rim diameter in inches (in) Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol –...
STARTING AND OPERATING 203 Tire Identification Number (TIN) the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on the The TIN may be found on one or both sides of the tire; outboard side, then you will find it on the inboard side of however, the date code may only be on one side.
204 STARTING AND OPERATING Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
STARTING AND OPERATING 205 Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 208
206 STARTING AND OPERATING Tire And Loading Information Placard WARNING! • Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them.
Page 209
STARTING AND OPERATING 207 Loading Steps For Determining Correct Load Limit— The vehicle maximum load on the tire must not exceed the (1) Locate the statement “The combined weight of load carrying capacity of the tire on your vehicle. You will occupants and cargo should never exceed XXX kg or not exceed the tire’s load carrying capacity if you adhere to XXX lbs.”...
Page 210
208 STARTING AND OPERATING Metric Example For Load Limit For example, if “XXX” amount equals 635 kg, and there will be five 68 kg passengers in your vehicle, the amount of available cargo and luggage load capacity is 295 kg (635- 340 (5x68) = 295 kg) as shown in step 4.
Page 211
STARTING AND OPERATING 209 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
210 STARTING AND OPERATING TIRES — GENERAL INFORMATION WARNING! (Continued) Tire Pressure • Overinflated or underinflated tires can affect vehicle handling and can fail suddenly, resulting in loss of Proper tire inflation pressure is essential to the safe and vehicle control. satisfactory operation of your vehicle.
STARTING AND OPERATING 211 Fuel Economy CAUTION! Underinflated tires will increase tire rolling resistance After inspecting or adjusting the tire pressure, always resulting in higher fuel consumption. reinstall the valve stem cap. This will prevent moisture Tread Wear and dirt from entering the valve stem, which could damage the valve stem.
212 STARTING AND OPERATING pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
STARTING AND OPERATING 213 Tire Types WARNING! All Season Tires — If Equipped Do not use Summer tires in snow/ice conditions. You All season tires provide traction for all seasons (Spring, could lose vehicle control, resulting in severe injury or Summer, Fall and Winter).
214 STARTING AND OPERATING While studded tires improve performance on ice, skid and Spare Tires — If Equipped traction capability on wet or dry surfaces may be poorer NOTE: For vehicles equipped with Tire Service Kit instead than that of non-studded tires. Some states prohibit stud- of a spare tire, please refer to the “Tire Service Kit”...
Page 217
STARTING AND OPERATING 215 Compact Spare Tire — If Equipped WARNING! The compact spare is for temporary emergency use only. Compact and Collapsible spares are for temporary You can identify if your vehicle is equipped with a compact emergency use only. With these spares, do not drive spare by looking at the spare tire description on the Tire more than 50 mph (80 km/h).
Page 218
216 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a Limited Use Spare — If Equipped conventional tire on the collapsible spare wheel, since the The limited use spare tire is for temporary emergency use wheel is designed specifically for the collapsible spare tire.
STARTING AND OPERATING 217 Tire Spinning When stuck in mud, sand, snow, or ice conditions, do not spin your vehicle’s wheels above 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping. Refer to “Freeing A Stuck Vehicle” in “What To Do In Emergencies”...
218 STARTING AND OPERATING Life Of Tire Keep dismounted tires in a cool, dry place with as little exposure to light as possible. Protect tires from contact with The service life of a tire is dependent upon varying factors oil, grease, and gasoline. including, but not limited to: Replacement Tires •...
STARTING AND OPERATING 219 It is recommended you contact your authorized tire dealer WARNING! (Continued) or original equipment dealer with any questions you may • Failure to equip your vehicle with tires having ad- have on tire specifications or capability. Failure to use equate speed capability can result in sudden tire equivalent replacement tires may adversely affect the failure and loss of vehicle control.
220 STARTING AND OPERATING WARNING! CAUTION! (Continued) • Observe the traction device manufacturer’s instruc- Using tires of different size and type (M+S, Snow) tions on the method of installation, operating speed, between front and rear axles can cause unpredictable and conditions for use. Always use the suggested handling.
STARTING AND OPERATING 221 The suggested rotation method is the “forward cross” outside temperature decreases, the tire pressure will de- shown in the following diagram. This rotation pattern does crease. Tire pressure should always be set based on cold not apply to some directional tires that must not be inflation tire pressure.
Page 224
222 STARTING AND OPERATING automatically update and the Tire Pressure Monitoring CAUTION! (Continued) Telltale Light will turn off once the system receives the equipped on your vehicle. Undesirable system op- updated tire pressures. The vehicle may need to be driven eration or sensor damage may result when using for up to 20 minutes above 15 mph (24 km/h) in order for replacement equipment that is not of the same size,...
STARTING AND OPERATING 223 • Driving on a significantly under-inflated tire causes the NOTE: It is particularly important for you to check the tire tire to overheat and can lead to tire failure. Under- pressure in all of the tires on your vehicle regularly and to inflation also reduces fuel efficiency and tire tread life, maintain the proper pressure.
224 STARTING AND OPERATING Check TPMS Warnings 1. The spare tire has a tire pressure monitoring sensor, but it is not monitored until it is mounted in place of any of The Tire Pressure Monitoring Telltale Light will flash on the existing four road tires.
STARTING AND OPERATING 225 (2) This device must accept any interference received, Poor quality gasoline can cause problems such as hard including interference that may cause undesired operation. starting, stalling, and hesitations. If you experience these symptoms, try another brand of gasoline before consider- NOTE: Changes or modifications not expressly approved ing service for the vehicle.
226 STARTING AND OPERATING E-85 Usage In Non-Flex Fuel Vehicles CAUTION! Non-Flex Fuel Vehicles (FFV) are compatible with gasoline DO NOT use gasoline containing methanol or gasoline containing up to 15% ethanol (E-15). Gasoline with higher containing more than 15% ethanol (E-15). Use of these ethanol content may void the New Vehicle Limited War- blends may result in starting and drivability problems, ranty.
STARTING AND OPERATING 227 MMT In Gasoline have these additives will help improve fuel economy, reduce emissions, and maintain vehicle performance. Methylcyclopentadienyl Manganese Tricarbonyl (MMT) is a manganese-containing metallic additive that is blended Designated TOP TIER Detergent Gaso- into some gasoline to increase octane. Gasoline blended line contains a higher level of detergents with MMT provides no performance advantage beyond to further aide in minimizing engine...
228 STARTING AND OPERATING Fuel System Cautions NOTE: Intentional tampering with the emissions control system can result in civil penalties being assessed against you. CAUTION! Carbon Monoxide Warnings Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gasoline is prohibited by Federal WARNING! law.
STARTING AND OPERATING 229 ADDING FUEL CAUTION! Fuel Filler Cap (Gas Cap) • Damage to the fuel system or emissions control The gas cap is located behind the fuel filler door on the left system could result from using an improper fuel side of the vehicle.
230 STARTING AND OPERATING NOTE: VEHICLE LOADING • When the fuel nozzle “clicks” or shuts off, the fuel tank As required by National Highway Traffic Safety Adminis- is full. tration regulations, your vehicle has a certification label affixed to the driver’s side door or B-Pillar. •...
Page 233
STARTING AND OPERATING 231 Gross Vehicle Weight Rating (GVWR) Rim Size The GVWR is the total allowable weight of your vehicle. This is the rim size that is appropriate for the tire size This includes driver, passengers, and cargo. The total load listed.
232 STARTING AND OPERATING Figure out the weight on the front and rear of the vehicle TRAILER TOWING separately. It is important that you distribute the load In this section you will find safety tips and information on evenly over the front and rear axles. limits to the type of towing you can reasonably do with your vehicle.
Page 235
STARTING AND OPERATING 233 Gross Trailer Weight (GTW) Tongue Weight (TW) The GTW is the weight of the trailer plus the weight of all The tongue weight is the downward force exerted on the cargo, consumables and equipment (permanent or tempo- hitch ball by the trailer.
Page 236
234 STARTING AND OPERATING Weight-Carrying Hitch WARNING! A weight-carrying hitch supports the trailer tongue weight, • An improperly adjusted Weight Distributing Hitch just as if it were luggage located at a hitch ball or some system may reduce handling, stability, braking per- other connecting point of the vehicle.
Page 237
STARTING AND OPERATING 235 Trailer Hitch Classification Definitions Class Max. Trailer Hitch Industry Standards Class I - Light Duty 2,000 lbs (907 kg) Class II - Medium Duty 3,500 lbs (1,587 kg) Class III - Heavy Duty 5,000 lbs (2,267 kg) Class IV - Extra Heavy Duty 10,000 lbs (4,535 kg) Refer to the “Trailer Towing Weights (Maximum Trailer Weight Ratings)”...
Page 238
236 STARTING AND OPERATING Consider the following items when computing the weight CAUTION! (Continued) on the rear axle of the vehicle: • Then, during the first 500 miles (805 km) that a trailer • The tongue weight of the trailer. is towed, do not drive over 50 mph (80 km/h) and do •...
Page 239
STARTING AND OPERATING 237 WARNING! (Continued) WARNING! (Continued) • When hauling cargo or towing a trailer, do not 2. GTW overload your vehicle or trailer. Overloading can 3. GAWR cause a loss of control, poor performance or damage to brakes, axle, engine, transmission, steering, sus- 4.
Page 240
238 STARTING AND OPERATING • When replacing tires, refer to “Tires – General Informa- WARNING! tion” in “Starting And Operating” for the proper tire • Do not connect trailer brakes to your vehicle’s hy- replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s draulic brake lines.
Page 241
STARTING AND OPERATING 239 The Trailer Tow Package may include a four- and seven-pin NOTE: wiring harness. Use a factory approved trailer harness and • Disconnect trailer wiring connector from the vehicle connector. before launching a boat (or any other device plugged into vehicle’s electrical connect) into water.
240 STARTING AND OPERATING Automatic Transmission The DRIVE range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing. However, if frequent shift- ing does occur while in DRIVE, select TOW/HAUL mode or select a lower gear range (using the Electronic Range Select [ERS] shift control).
STARTING AND OPERATING 241 Electronic Speed Control — If Equipped City Driving • Do not use in hilly terrain or with heavy loads. When stopped for short periods, shift the transmission into NEUTRAL and increase engine idle speed. • When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage until Highway Driving you can get back to cruising speed.
242 STARTING AND OPERATING NOTE: For vehicles equipped with diesel engine and CAUTION! electric park brake, see important information in the Diesel • DO NOT flat tow this vehicle. Damage to the drive- Supplement. train will result. If this vehicle requires towing, Recreational Towing —...
Page 245
WHAT TO DO IN EMERGENCIES CONTENTS ▫ Wheel Covers ......268 HAZARD WARNING FLASHERS ... .244 IF YOUR ENGINE OVERHEATS .
244 WHAT TO DO IN EMERGENCIES • In city traffic — while stopped, place the transmission in HAZARD WARNING FLASHERS NEUTRAL, but do not increase the engine idle speed The Hazard Warning flasher switch is located on the while preventing vehicle motion with the brakes. instrument panel below the climate controls.
WHAT TO DO IN EMERGENCIES 245 **Use only your authorized dealer recommended lug nuts/ CAUTION! bolts and clean or remove any dirt or oil before tightening. Driving with a hot cooling system could damage your Inspect the wheel mounting surface prior to mounting the vehicle.
246 WHAT TO DO IN EMERGENCIES Tighten the lug nuts/bolts in a star pattern until each TIRE SERVICE KIT — IF EQUIPPED nut/bolt has been tightened twice. Small punctures up to 1/4 inch (6 mm) in the tire tread can be sealed with Tire Service Kit.
WHAT TO DO IN EMERGENCIES 247 Tire Service Kit Components And Operation Using The Mode Select Knob And Hoses Your Tire Service Kit is equipped with the following symbols to indicate the air or sealant mode. Selecting Air Mode Push in the Mode Select Knob (5) and turn to this position for air pump operation only.
248 WHAT TO DO IN EMERGENCIES • When the Tire Service Kit sealant is in a liquid form, Tire Service Kit Usage Precautions clean water, and a damp cloth will remove the material • Replace the Tire Service Kit Sealant Bottle (1) and Sealant from the vehicle or tire and wheel components.
Page 251
WHAT TO DO IN EMERGENCIES 249 WARNING! WARNING! (Continued) in injuries that are serious or fatal to you, your • Do not attempt to seal a tire on the side of the vehicle passengers, and others around you. closest to traffic. Pull far enough off the road to avoid •...
250 WHAT TO DO IN EMERGENCIES Sealing A Tire With Tire Service Kit 3. Place the Tire Service Kit flat on the ground next to the deflated tire. (A) Whenever You Stop To Use Tire Service Kit: 4. Remove the cap from the valve stem and then screw the 1.
Page 253
WHAT TO DO IN EMERGENCIES 251 If the sealant (white fluid) does not flow within 0 – 10 As the sealant flows through the Sealant Hose (6), the seconds through the Sealant Hose (6): Pressure Gauge (3) can read as high as 70 psi (4.8 Bar). The Pressure Gauge (3) will decrease quickly from 1.
Page 254
252 WHAT TO DO IN EMERGENCIES 2. Remove the Speed Limit sticker from the top of the distribution of the Tire Service Kit Sealant within the tire. Sealant Bottle (1) and place the sticker on the instrument Do not exceed 55 mph (90 km/h). panel.
Page 255
WHAT TO DO IN EMERGENCIES 253 If tire pressure is less than 19 psi (1.3 Bar): 6. Replace the Sealant Bottle (1) and Sealant Hose (6) assembly at your authorized dealer as soon as possible. The tire is too badly damaged. Do not attempt to drive the Refer to (F) “Sealant Bottle and Hose Replacement”.
254 WHAT TO DO IN EMERGENCIES 6. Verify that the cap is installed on the fitting at the end of WARNING! (Continued) the Sealant Hose (6) and return the hose to its storage vehicle for service purposes. The vehicle should be area (located on the bottom of the air pump).
Page 257
WHAT TO DO IN EMERGENCIES 255 To release the jack kit for it’s storage location, you must To open the jack kit container you must push the containers push down and turn the lock knob 1/4 turn counter release to separate the top and bottom. clockwise to the unlock position.
256 WHAT TO DO IN EMERGENCIES Removing The Spare Tire 1. Remove the spare tire before attempting to jack up the vehicle. Attach the lug bolt adapter to the winch exten- sion and insert it into the winch mechanism. Jacking Tools 1 —...
Page 259
WHAT TO DO IN EMERGENCIES 257 Winch Location Winch Extension The winch mechanism is located under the rear of the 2. Rotate the wheel wrench handle counterclockwise until vehicle to the right of the spare tire. the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
Page 260
258 WHAT TO DO IN EMERGENCIES NOTE: The winch mechanism is designed for use with the 3. Pull the spare tire out from under the vehicle to gain winch extension tube only. Use of an air wrench or other access to the spare tire retainer. power tools is not recommended and can damage the winch.
Page 261
WHAT TO DO IN EMERGENCIES 259 4. Remove the retainer nut prior to removing the retainer 5. Lift the spare tire with one hand to give clearance to tilt from the wheel. the retainer at the end of the cable. Retainer Nut Lifting Spare Tire...
260 WHAT TO DO IN EMERGENCIES 6. Pull the retainer through the center of the wheel. 2. Turn on the Hazard Warning flasher. 3. Set the parking brake firmly. 4. Set an automatic transmission in PARK; a manual transmission in REVERSE. 5.
Page 263
WHAT TO DO IN EMERGENCIES 261 WARNING! (Continued) • Block the wheel diagonally opposite the wheel to be raised. • Set the parking brake firmly and set an automatic transmission in PARK; a manual transmission in REVERSE. • Never start or run the engine with the vehicle on a jack.
Page 264
262 WHAT TO DO IN EMERGENCIES 1. Loosen (but do not remove) the wheel lug bolts by CAUTION! turning them to the left one turn while the wheel is still on the ground. Do not attempt to raise the vehicle by jacking on locations other than those indicated in the Jacking 2.
Page 265
WHAT TO DO IN EMERGENCIES 263 CAUTION! Do not attempt to raise the vehicle by jacking on locations other than those indicated. NOTE: The rear jacking location is located in front of the rear tire and in front of the leaf spring mount. Front Jacking Location WARNING! Being under a jacked-up vehicle is dangerous.
Page 266
264 WHAT TO DO IN EMERGENCIES 3. Place the wrench handle and lug bolt adapter on the jack screw and turn to the right until the jack head is properly engaged in the described location. Do not raise the vehicle until you are sure the jack is securely engaged.
Page 267
WHAT TO DO IN EMERGENCIES 265 CAUTION! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. NOTE: Do not install the wheel cover on the spare tire. 7.
Page 268
266 WHAT TO DO IN EMERGENCIES 12. Stow the jack, jack handle and winch handle tools back in the storage compartment. WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the occupants of the vehicle. Always stow the jack parts and the spare tire in the places provided.
Page 269
WHAT TO DO IN EMERGENCIES 267 For vehicles with aluminum wheels: 3. Tighten the knob on the bolt to secure it to the bracket. 1. Remove the adapter bracket and bolts from the storage bag in the glove compartment. 2. Take the retainer and position it inside the circular bracket.
268 WHAT TO DO IN EMERGENCIES Alloy Wheel Mounting Wheel/Bolts Attaching To Mounting Bracket 4. Position the tire vertically and lay the mounted adapter 5. Follow the steps above for proper spare tire stowage. on the inner part of the rim. Using the supplied bolts, Wheel Covers fasten the wheel to the adapter using the bolt install wrench.
WHAT TO DO IN EMERGENCIES 269 JUMP-STARTING PROCEDURES The Remote Positive (+) Post is covered with a protective cap located on the side of the Front Power Distribution If your vehicle has a discharged battery, it can be jump- Center. started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack.
270 WHAT TO DO IN EMERGENCIES WARNING! WARNING! • Take care to avoid the radiator cooling fan whenever Do not allow vehicles to touch each other as this could the hood is raised. It can start anytime the ignition establish a ground connection and personal injury switch is ON.
Page 273
WHAT TO DO IN EMERGENCIES 271 NOTE: The remote positive (+) post is located in the 5. Start the engine in the vehicle that has the booster engine compartment on the driver’s side under the cover of battery. Let the engine idle a few minutes and then start the Front Power Distribution Center.
272 WHAT TO DO IN EMERGENCIES CAUTION! Accessories plugged into the vehicle power outlets draw power from the vehicle’s battery, even when not in use (i.e., cellular devices, etc.). Eventually, if plugged in long enough without engine operation, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent the engine from starting.
WHAT TO DO IN EMERGENCIES 273 NOTE: Vehicles with diesel engine (automated manual transmission) cannot be rocked in this manner, because the transmission will not allow shifts between forward and REVERSE gears while the wheels are turning. CAUTION! Racing the engine or spinning the wheels may lead to transmission overheating and failure.
274 WHAT TO DO IN EMERGENCIES GEAR SELECTOR OVERRIDE WARNING! If a malfunction occurs and the gear selector cannot be Fast spinning tires can be dangerous. Forces generated moved out of the PARK position, you can use the following by excessive wheel speeds may cause damage, or even procedure to temporarily move the gear selector: failure, of the axle and tires.
Page 277
WHAT TO DO IN EMERGENCIES 275 Towing Condition Wheels OFF The ALL Models Ground Flat Tow NONE If transmission is operable: • Transmission in NEUTRAL Wheel Lift Or Dolly Rear • 25 mph (40 km/h) max speed • 15 miles (24 km) max distance Front Flatbed BEST METHOD...
276 WHAT TO DO IN EMERGENCIES Automatic Transmission CAUTION! (Continued) The manufacturer recommends towing your vehicle with • Towing this vehicle in violation of the above require- all four wheels OFF the ground using a flatbed. ments can cause severe transmission damage. Dam- age from improper towing is not covered under the If flatbed equipment is not available, and the transmission New Vehicle Limited Warranty.
Page 279
MAINTAINING YOUR VEHICLE CONTENTS ▫ Air Conditioner Maintenance ....288 ENGINE COMPARTMENT — 3.6L ...279 ▫ Body Lubrication ..... .291 ONBOARD DIAGNOSTIC SYSTEM —...
Page 280
278 MAINTAINING YOUR VEHICLE ▫ Rear Tail, Stop, Backup, Turn Signal And Rear Side REPLACEMENT BULBS ....314 Marker Lamps ......318 BULB REPLACEMENT .
280 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! (Continued) Your vehicle is equipped with a sophisticated Onboard • If the MIL is flashing while the engine is running, Diagnostic system called OBD II. This system monitors the severe catalytic converter damage and power loss performance of the emissions, engine, and automatic trans- will soon occur.
MAINTAINING YOUR VEHICLE 281 EMISSIONS INSPECTION AND MAINTENANCE WARNING! (Continued) PROGRAMS vehicle control could occur that may result in an In some localities, it may be a legal requirement to pass an accident involving serious injury or death. inspection of your vehicle’s emissions control system. •...
282 MAINTAINING YOUR VEHICLE 2. As soon as you cycle the ignition to the ON mode, you Regardless of whether your vehicle’s OBD II system is will see the “Malfunction Indicator Light (MIL)” symbol ready or not, if the MIL is illuminated during normal come on as part of a normal bulb check.
MAINTAINING YOUR VEHICLE 283 WARNING! CAUTION! (Continued) have potential malfunctions examined by an autho- You can be badly injured working on or around a rized dealer or qualified repair center. motor vehicle. Only do service work for which you • Your vehicle has been built with improved fluids have the knowledge and the proper equipment.
Page 286
284 MAINTAINING YOUR VEHICLE oil level between the MIN and MAX markings on the American Petroleum Institute (API) Engine Oil dipstick. Adding one quart of oil when the reading is at the Identification Symbol MIN mark will result in a MAX reading on these engines. This symbol means that the oil has been CAUTION! certified by the American Petroleum In-...
MAINTAINING YOUR VEHICLE 285 The engine oil filler cap also shows the recommended engine oil. Engine oil is an engineered product and its engine oil viscosity for your engine. For information on performance may be impaired by supplemental additives. engine oil filler cap location, refer to the “Engine Compart- Disposing Of Used Engine Oil And Oil Filters ment”...
286 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Exhaust System Refer to the “Maintenance Schedule” for the proper main- The best protection against carbon monoxide entry into the tenance intervals. vehicle body is a properly maintained engine exhaust system. WARNING! If you notice a change in the sound of the exhaust system;...
Page 289
MAINTAINING YOUR VEHICLE 287 Under normal operating conditions, the catalytic converter WARNING! (Continued) will not require maintenance. However, it is important to • A hot exhaust system can start a fire if you park over keep the engine properly tuned to assure proper catalyst materials that can burn.
288 MAINTAINING YOUR VEHICLE Maintenance-Free Battery CAUTION! Your vehicle is equipped with a maintenance-free battery. • It is essential when replacing the cables on the You will never have to add water, nor is periodic mainte- battery that the positive cable is attached to the nance required.
Page 291
MAINTAINING YOUR VEHICLE 289 Refrigerant Recovery And Recycling WARNING! R-134a Air Conditioning Refrigerant is a hydrofluoro- • Use only refrigerants and compressor lubricants ap- carbon (HFC) that is endorsed by the Environmental proved by the manufacturer for your air conditioning Protection Agency and is an ozone-saving product.
Page 292
290 MAINTAINING YOUR VEHICLE The A/C air filter is located in the fresh air inlet in the engine compartment. Perform the following procedure to replace the filter: 1. Remove the two screws that secure the filter retainer to the fresh air inlet, and remove the filter retainer. Removing Air Filer 1 —...
MAINTAINING YOUR VEHICLE 291 Body Lubrication Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades. Always use washer Locks and all body pivot points, including such items as fluid when using the wipers to remove salt or dirt from a seat tracks, door hinge pivot points and rollers, liftgate, dry windshield.
292 MAINTAINING YOUR VEHICLE WARNING! WARNING! (Continued) • You or others can be badly burned by hot engine Commercially available windshield washer solvents coolant (antifreeze) or steam from your radiator. If are flammable. They could ignite and burn you. Care you see or hear steam coming from under the hood, must be exercised when filling or working around the do not open the hood until the radiator has had time...
Page 295
MAINTAINING YOUR VEHICLE 293 If the engine coolant (antifreeze) is dirty or contains visible CAUTION! (Continued) sediment, have an authorized dealer clean and flush with OAT coolant (conforming to MS.90032), by an autho- OAT coolant (antifreeze) (conforming to MS.90032). rized dealer as soon as possible. Refer to the “Maintenance Schedule”...
Page 296
294 MAINTAINING YOUR VEHICLE Please review these recommendations for using Organic NOTE: Additive Technology (OAT) engine coolant (antifreeze) • It is the owner’s responsibility to maintain the proper that meets the requirements of FCA Material Standard level of protection against freezing according to the MS.90032.
Page 297
MAINTAINING YOUR VEHICLE 295 The cap should be inspected and cleaned if there is any Coolant Level accumulation of foreign material on the sealing surfaces. The coolant expansion bottle provides a quick visual method for determining that the coolant level is adequate. WARNING! With engine off and cold, the level of the engine coolant (antifreeze) in the bottle should be between the “MIN”...
296 MAINTAINING YOUR VEHICLE • If frequent engine coolant (antifreeze) additions are to the “Maintenance Schedule” for the proper maintenance required, the cooling system should be pressure tested intervals. for leaks. WARNING! • Maintain engine coolant (antifreeze) concentration at a minimum of 50% OAT coolant (conforming to Riding the brakes can lead to brake failure and possi- MS.90032) and distilled water for proper corrosion pro-...
MAINTAINING YOUR VEHICLE 297 fluid level can be expected to fall as the brake pads wear. WARNING! (Continued) However, low fluid level may be caused by a leak and a to boil unexpectedly during hard or prolonged brak- checkup may be needed. ing, resulting in sudden brake failure.
Page 300
298 MAINTAINING YOUR VEHICLE transmission fluid at the correct level using the recom- CAUTION! mended fluid. No chemical flushes should be used in any transmission; only the approved lubricant should be used. Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- CAUTION! nents.
MAINTAINING YOUR VEHICLE 299 Fluid And Filter Changes What Causes Corrosion? Corrosion is the result of deterioration or removal of paint Refer to the “Maintenance Schedule” for the proper main- and protective coatings from your vehicle. tenance intervals. The most common causes are: In addition, change the fluid and filter if the fluid becomes •...
Page 302
300 MAINTAINING YOUR VEHICLE • If you carry special cargo such as chemicals, fertilizers, CAUTION! de-icer salt, etc., be sure that such materials are well • Do not use abrasive or strong cleaning materials such packaged and sealed. as steel wool or scouring powder that will scratch •...
Page 303
MAINTAINING YOUR VEHICLE 301 NOTE: Many aftermarket wheel cleaners contain strong CAUTION! acids or strong alkaline additives that can harm the wheel surface. Do not use scouring pads, steel wool, a bristle brush, metal polishes or oven cleaner. These products may damage the CAUTION! wheel’s protective finish.
Page 304
302 MAINTAINING YOUR VEHICLE Stain Repel Fabric Cleaning Procedure — If Your leather upholstery can be best preserved by regular Equipped cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and Stain Repel seats may be cleaned in the following manner: should be removed promptly with a damp cloth.
Page 305
MAINTAINING YOUR VEHICLE 303 glass cleaner. Never use an abrasive type cleaner. Use CAUTION! (Continued) caution when cleaning the inside rear window equipped • Damage caused by these type of products may not be with electric defrosters or windows equipped with radio covered by your New Vehicle Limited Warranty.
304 MAINTAINING YOUR VEHICLE If the belts need cleaning, use Mopar Total Clean, a mild Cleaning soap solution, or lukewarm water. Do not remove the belts The liner is top shelf dishwasher safe, or you may follow from the vehicle to wash them. Dry with a soft cloth. the cleaning procedure below.
MAINTAINING YOUR VEHICLE 305 FUSES Underhood Fuses The Front Power Distribution Center is located on the WARNING! driver’s side of the engine compartment. To access the fuses, remove the cover. • When replacing a blown fuse, always use an appro- priate replacement fuse with the same amp rating as the original fuse.
Page 308
306 MAINTAINING YOUR VEHICLE The ID number of the electrical component corresponding to each fuse can be found on the back of the cover. Cavity Maxi Fuse Mini Fuse Description 40 Amp Orange – Electronic Stability Control (ESC) Pump 20 Amp Yellow (3.6 –...
Page 309
MAINTAINING YOUR VEHICLE 307 Cavity Maxi Fuse Mini Fuse Description 40 Amp Orange – Passenger Compartment Blower – 15 Amp Blue Rear Power Outlet – 15 Amp Blue Horn – 15 Amp Blue Fuel Pressure Regulator (MPROP)-DRV (3.0 Diesel Engine) — If Equipped –...
Page 310
308 MAINTAINING YOUR VEHICLE Cavity Maxi Fuse Mini Fuse Description – 7.5 Amp Brown KL30 Manual Transmission Automated (MTA), KL30 Engine Control Module (ECM), KL30 Main Relay Coil (3.0 Diesel Engine) – 7.5 Amp Brown A/C Compressor — If Equipped –...
Page 311
MAINTAINING YOUR VEHICLE 309 Front PDC Additional Fuses The additional fuse box is located inside the front PDC Box. Front Power Distribution Center Additional Fuses Cavity Mini Fuse Description 20 Amp Yellow Vacuum Pump (3.6 Gasoline Engine) — If Equipped 30 Amp Green Transmission Power RELE (3.6 Gasoline Engine) —...
310 MAINTAINING YOUR VEHICLE Interior Fuses The interior fuse panel is part of the Body Control Module (BCM) and is located on the driver’s side under the instrument panel. Fuse Panel...
Page 313
MAINTAINING YOUR VEHICLE 311 Fuse Panel Cavity Locations Cavity Mini Fuse Description 10 Amp Red Right Low Beam 10 Amp Red Left Low Beam 5 Amp Beige INT/A 10 Amp Red SBMT...
Page 314
312 MAINTAINING YOUR VEHICLE Cavity Mini Fuse Description 7.5 Amp Brown Clearance Lights 15 Amp Blue +30 (ACM – TPCU – RRM – DLC) 5 Amp Beige INT (BRAKE NO – IPC) 15 Amp Blue Central Locking 5 Amp Beige INT (BSM –...
MAINTAINING YOUR VEHICLE 313 Right Central Pillar Fuses The right central pillar fuse panel is located on the interior side at the base of the passenger side B pillar. Fuse Panel Fuse Panel Location Cavity Mini Fuse Description 7.5 Amp Brown Seat Heater 20 Amp Yellow Rear Left Windows Heater...
314 MAINTAINING YOUR VEHICLE VEHICLE STORAGE (e.g., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes in the If you are leaving your vehicle dormant for more than 21 fresh air and high blower setting. This will ensure days, you may want to take these steps to protect your adequate system lubrication to minimize the possibility battery.
Page 317
MAINTAINING YOUR VEHICLE 315 Exterior Bulbs Bulb Number Front Low and High Beam Headlamp H7LL Front Park/Turn Signal Lamps 7444NA Daytime Running Lamps (If Equipped) 7440 Front Side Marker Lamps WY5W Rear Tail/Stop Lamps 7443 Rear Turn Signal Lamps 7440NA Rear Backup Lamps Rear Side Marker Lamps Front Fog Lamps...
316 MAINTAINING YOUR VEHICLE BULB REPLACEMENT 9. Pull bulb outward from socket. NOTE: Lens fogging can occur under certain atmospheric 10. Install new bulb. conditions. This will usually clear as atmospheric condi- 11. Push socket back into reflector until it locks back into tions change to allow the condensation to change back into place.
MAINTAINING YOUR VEHICLE 317 3. Remove one upper screw from the headlamp housing. 1. Remove one screw on the lower headlamp filler panel. 4. Remove two lower screws from the headlamp housing. 2. Remove two screws on the upper headlamp filler panel. 5.
318 MAINTAINING YOUR VEHICLE Front Fog Lamps Rear Tail, Stop, Backup, Turn Signal And Rear Side Marker Lamps 1. Turn front wheels inboard to access cover in wheel liner. 1. Open rear doors. 2. Open the cover on the front of the wheel liner. 2.
Page 321
MAINTAINING YOUR VEHICLE 319 Rear Cargo Lamp Bulb Access Cargo Lamp Bulb Location 2. Using a suitable tool, pull open the metal bulb access on 3. Remove and install the replacement bulb. the back of the housing. 4. Close the bulb access, connect the lamp and install the lamp into place.
320 MAINTAINING YOUR VEHICLE Dome Lamps 2. Using a suitable tool, flex the housing to lift the light pod cover away from the unit. 1. Using a suitable tool, insert the tip at the location shown and press inward to the lamp to relieve the spring tension.
MAINTAINING YOUR VEHICLE 321 3. Remove and replace the bulbs as needed. 4. Close the housing cover making sure it snaps together properly and connect the lamp. 5. Install overhead console into place making sure to seat the assembly’s forward end first and then snapping it flush so that the tension spring is fully seating in the housing.
322 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) meeting the requirements of FCA Material Standard MS.90032. Engine Oil We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as Mopar, Pennzoil, and Shell Helix.
MAINTAINING YOUR VEHICLE 323 CAUTION! (Continued) CAUTION! (Continued) rust inhibitors or antirust products, as they may not OAT coolant (conforming to MS.90032), by an autho- rized dealer as soon as possible. be compatible with the radiator engine coolant and • Do not use water alone or alcohol-based engine may plug the radiator.
Page 328
326 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE NOTE: Under no circumstances should oil change inter- vals exceed 10,000 miles (16,000 km), twelve months or 350 Your vehicle is equipped with an automatic oil change hours of engine run time, whichever comes first. The 350 indicator system.
Page 329
MAINTENANCE SCHEDULES 327 Maintenance Chart At Every Oil Change Interval As Indicated By Oil Change Indicator System: Required Maintenance Intervals • Inspect brake pads, shoes, rotors, drums, hoses and Refer to the maintenance schedules on the following page park brake. for the required maintenance intervals.
Page 330
328 MAINTENANCE SCHEDULES Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, boot seals, and replace if necessary. Inspect the brake pads, replace as necessary. Additional Maintenance Replace engine air filter.
Page 331
MAINTENANCE SCHEDULES 329 Mileage or time passed (which- ever comes first) Or Years: Or Kilometers: Inspect and replace PCV valve if necessary. * The brake fluid change interval is time based only, WARNING! (Continued) mileage intervals do not apply. • Failure to properly inspect and maintain your vehicle ** The spark plug change interval is mileage based only, could result in a component malfunction and effect yearly intervals do not apply.
Page 333
IF YOU NEED CONSUMER ASSISTANCE CONTENTS SUGGESTIONS FOR OBTAINING SERVICE FOR WARRANTY INFORMATION ....335 YOUR VEHICLE ......332 MOPAR PARTS .
332 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to bring the right papers with you, as well as your warranty folder.
IF YOU NEED CONSUMER ASSISTANCE 333 Any communication to the manufacturer’s customer center In Mexico Contact should include the following information: Av. Prolongacion Paseo de la Reforma, 1240 • Owner’s name and address Sante Fe C.P. 05109 • Owner’s telephone number (home and office) Mexico, D.
334 IF YOU NEED CONSUMER ASSISTANCE Canadian residents with hearing difficulties that require Limited Warranty expires, please refer to the contract assistance can use the special needs relay service offered by documents, and contact the person listed in those docu- Bell Canada.
IF YOU NEED CONSUMER ASSISTANCE 335 WARRANTY INFORMATION To contact NHTSA, you may call the Vehicle Safety Hotline toll free at 1-888-327-4236 (TTY: 1-800-424-9153); See the Warranty Information Booklet, for the terms and or go to http://www.safercar.gov; or write to: Admin- provisions of FCA US LLC warranties applicable to this istrator, NHTSA, 1200 New Jersey Avenue, SE., West vehicle and market.
336 IF YOU NEED CONSUMER ASSISTANCE Service Manuals Call toll free at: • 1-800-890-4038 (U.S.) These comprehensive Service Manuals provide the infor- mation that students and professional technicians need in • 1-800-387-1143 (Canada) diagnosing/troubleshooting, problem solving, maintain- ing, servicing, and repairing FCA US LLC vehicles. A complete working knowledge of the vehicle, system, Visit us on the Worldwide Web at: and/or components is written in straightforward language...
IF YOU NEED CONSUMER ASSISTANCE 337 100. The relative performance of tires depends upon the Temperature Grades actual conditions of their use, however, and may depart The temperature grades are A (the highest), B, and C, significantly from the norm due to variations in driving representing the tire’s resistance to the generation of habits, service practices, and differences in road charac- heat and its ability to dissipate heat, when tested under...
Page 350
348 INDEX Lap/Shoulder Belt Operation ....26 Sentry Key (Immobilizer) ..... .13 Lap/Shoulder Belts .
Page 351
INDEX 349 Storing Your Vehicle ......314 Sizes ....... . .201 Supplemental Restraint System - Air Bag.
Page 352
350 INDEX Trailer And Tongue Weight ....235 Viscosity, Engine Oil ......284 Wiring .
Page 353
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
Need help?
Do you have a question about the PROMASTER 2017 and is the answer not in the manual?
Questions and answers
MY VAN WONT START BECAUSE OF THE ESC SAYS IT NEEDS SERVICED. IT STARTED WHEN I HAD IT PARKED ON A DECLINE AND WHEN IT DRIFTED DOWN AND I TURNED IT OFF IT WOULDNT START BACK UP. I WAS ABLE TO RESET IT ONCE BEFORE BY UNPLUGGING THE BATTERY AND WHEN I PARKE OD THE SAME HILL AND IT DRIFTED AGAIN I CANT SEEM TO DUPICATE THE RESTART. PLWEASE ADVISE
If a 2017 RAM Commercial ProMaster won’t start due to ESC service requirements, consider the following steps:
1. Check the ESC Indicator Lights – If the “ESC Activation/Malfunction Indicator Light” remains on continuously while the engine is running, there may be a system malfunction.
2. Turn the Ignition Off and On – Restarting the vehicle may reset the ESC system. Ensure the ignition switch is in the ON position and check if the light turns off when the engine runs.
3. Drive the Vehicle – If the light remains on, drive the vehicle for several miles at speeds greater than 30 mph (48 km/h) to see if the issue resolves.
4. Listen for System Sounds – The ESC system may produce buzzing or clicking sounds when active. This is normal and indicates it is functioning properly.
5. Check for Power Reduction – If the vehicle is in “Partial Off” mode, the engine power reduction feature of the Traction Control System (TCS) is disabled, which may affect the ESC system.
6. Consult a Dealer – If the ESC malfunction light remains on after multiple ignition cycles and driving, contact an authorized dealer for diagnosis and repair.
These steps can help identify and possibly resolve ESC-related starting issues.
This answer is automatically generated