Page 2
This Owner’s Manual illustrates and describes the operation of features and equipment that are either standard or optional on this vehicle. This manual may also include a description of features and equipment that are no longer available or were not ordered on this vehicle. Please disregard any features and equipment that are no longer available or were not ordered on this vehicle.
TABLE OF CONTENTS INTRODUCTION ..........................10 GETTING TO KNOW YOUR VEHICLE ..................12 GETTING TO KNOW YOUR INSTRUMENT PANEL ............82 SAFETY ............................120 STARTING AND OPERATING ....................183 IN CASE OF EMERGENCY ....................294 SERVICING AND MAINTENANCE ..................329 TECHNICAL SPECIFICATIONS .................... 397 MULTIMEDIA ..........................414 CUSTOMER ASSISTANCE ....................
Page 4
INTRODUCTION HEAD RESTRAINTS ..........36 REMOTE START — IF EQUIPPED (DIESEL)..20 How To Use Remote Start ......21 Front Head Restraints ......... 36 HOW TO USE THIS MANUAL .......11 Remote Start Abort Message...... 21 Rear Head Restraint Adjustment ....37 Essential Information ........
Page 5
CLIMATE CONTROLS ........... 51 GETTING TO KNOW YOUR INSTRUMENT PANEL EXTERIOR LIGHTS ..........44 Multifunction Lever........44 Manual Climate Control Overview .... 52 BASE / MIDLINE INSTRUMENT CLUSTER..82 Headlight Switch .......... 44 Automatic Climate Control Overview ..55 Base / Midline Instrument Cluster Daytime Running Lights (DRLs) ....
Page 6
STARTING AND OPERATING ONBOARD DIAGNOSTIC SYSTEM — OBD II ..118 NORMAL OPERATION — DIESEL ENGINE ..194 Onboard Diagnostic System (OBD II) Cold Weather Precautions ......194 STARTING THE ENGINE — GAS ENGINE ..183 Cybersecurity..........118 Engine Idling ..........197 Automatic Transmission......183 EMISSIONS INSPECTION AND MAINTENANCE Noise ............198 Tip Start Feature ........183...
Page 7
PARKSENSE FRONT AND REAR FOUR-WHEEL DRIVE OPERATION — Activating Adaptive Cruise Control (ACC)..........234 IF EQUIPPED ............218 PARK ASSIST ........... 250 To Activate/Deactivate......234 Electronically Shifted Transfer Case (Eight ParkSense Sensors ........251 To Set A Desired ACC Speed.....235 Speed Transmission) — If Equipped ..219 ParkSense Warning Display......
Page 8
REFUELING THE VEHICLE — SNOWPLOW ............286 JACKING AND TIRE CHANGING ...... 314 DIESEL ENGINE ..........269 Before Plowing ...........286 4500/5500 Models ........315 Snowplow Prep Package Model Preparations For Jacking ......315 Fuel Filler Cap ..........269 Availability ..........286 Jacking Instructions 4500 And Avoid Using Contaminated Fuel....269 Over The Road Operation With Snowplow 5500 Series ..........315...
Page 9
SERVICING AND MAINTENANCE Priming If The Engine Has Run DEPARTMENT OF TRANSPORTATION UNIFORM Out Of Fuel ..........358 TIRE QUALITY GRADES ........392 SCHEDULED SERVICING — GAS ENGINE ..329 Intervention Regeneration Strategy — Treadwear ..........392 Maintenance Plan........330 Message Process Flow ......359 Traction Grades .........
Page 10
MULTIMEDIA FUEL REQUIREMENTS — GAS ENGINE ..399 VOICE RECOGNITION QUICK TIPS ....485 6.4L Engine ..........399 Introducing Uconnect ........485 UCONNECT SYSTEMS ........414 Reformulated Gasoline ......399 Get Started..........485 CYBERSECURITY ..........414 Materials Added To Fuel ......400 Basic Voice Commands ......485 UCONNECT SETTINGS ........415 Gasoline/Oxygenate Blends ....400 Radio ............486...
Page 11
CUSTOMER ASSISTANCE WARRANTY INFORMATION ......502 MOPAR PARTS ...........502 SUGGESTIONS FOR OBTAINING SERVICE FOR REPORTING SAFETY DEFECTS ......502 YOUR VEHICLE ..........500 In The 50 United States And Prepare For The Appointment....500 Washington, D.C........502 Prepare A List..........500 In Canada...........502 Be Reasonable With Requests ....500 PUBLICATION ORDER FORMS ......503 IF YOU NEED ASSISTANCE ......
INTRODUCTION cial and local laws wherever you drive. As with This Owner's Manual describes all versions of Dear Customer, congratulations on selecting other vehicles of this type, failure to operate this this vehicle. Options and equipment dedicated your new vehicle. Be assured that it represents vehicle correctly may result in loss of control or to specific markets or versions are not expressly precision workmanship, distinctive styling, and...
INTRODUCTION HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS Operating instructions for the special equip- ment installed by the conversion/camper This Owner’s Manual contains WARNINGS Essential Information manufacturer should also be supplied with your against operating procedures that could result vehicle.
GETTING TO KNOW YOUR VEHICLE VEHICLE USER GUIDE — IF EQUIPPED NOTE: connect and no external device needed for play- Vehicle User Guide features are not available back. Plus, it’s updated throughout the year, in Access your Owner’s Information right through while the vehicle is moving.
GETTING TO KNOW YOUR VEHICLE TIP: NOTE: In case the ignition switch does not change with When viewing a topic, tap the star icon to add it the push of a button, the key fob may have a low In the ON/RUN position, all key fob buttons ...
Page 16
GETTING TO KNOW YOUR VEHICLE To Lock The Doors Using The Panic Alarm NOTE: If the vehicle is equipped with remote power To turn the Panic Alarm feature on or off, push Perchlorate Material — special handling may door locks, push and release the lock button on the Panic button on the key fob.
Page 17
GETTING TO KNOW YOUR VEHICLE 2. Slightly remove the emergency key from the NOTE: key fob, approximately 10 mm. The blade of When replacing the battery, ensure the + sign the emergency key should just become on the battery is facing upward. Avoid touching the new battery with your fingers.
Page 18
GETTING TO KNOW YOUR VEHICLE 6. To assemble the key fob case, line up the NOTE: Le présent appareil est conforme aux CNR top edge of the back cover with the top of The key fob battery should only be replaced by d`Innovation, Science and Economic Develop- the fob, and press the edges into the inter- qualified technicians.
GETTING TO KNOW YOUR VEHICLE IGNITION SWITCH Driving position. Keyless Push Button Ignition All the electrical devices are available. This feature allows the driver to operate the igni- START tion switch with the push of a button as long as the Remote Keyless Entry key fob is in the The engine will start.
GETTING TO KNOW YOUR VEHICLE REMOTE START — IF EQUIPPED WARNING! (Continued) (GASOLINE) Do not leave children or animals inside parked vehicles in hot weather. Interior This system uses the key fob to start heat build-up may cause serious injury or the engine conveniently from outside death.
GETTING TO KNOW YOUR VEHICLE System not disabled from previous remote Remote Start Cancelled — Fuel Low The park lamps will turn on and remain on start event during Remote Start mode. Remote Start Cancelled — System Fault ...
GETTING TO KNOW YOUR VEHICLE To Exit Remote Start Mode And Drive The General Information La operación de este equipo está sujeta a las Vehicle siguientes dos condiciones: The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this Before the end of the 15 minute cycle, push and 1.
GETTING TO KNOW YOUR VEHICLE The Remote Start system will wait for the Wait To Start Light Indicator Light is not illu- The instrument cluster display message is “Wait To Start” Indicator Light to extinguish minated stored until the ignition is placed in the ON/RUN before cranking the engine.
GETTING TO KNOW YOUR VEHICLE SENTRY KEY Additional features, such as windshield alarm System (if equipped). Then, prior to the wipers, will also not be available while the end of the 15 minute cycle, place the ignition in The Sentry Key Immobilizer system prevents vehicle is in the Remote Start mode.
GETTING TO KNOW YOUR VEHICLE If the vehicle security light turns on during programmed to a vehicle, it cannot be This device complies with Part 15 of the FCC normal vehicle operation (vehicle running for programmed to any other vehicle. Rules and with Innovation, Science and longer than 10 seconds), it indicates that there Economic Development Canada license-exempt...
GETTING TO KNOW YOUR VEHICLE La operación de este equipo está sujeta a las To Arm The System closed, the vehicle security light, in the instru- siguientes dos condiciones: ment panel cluster, will flash rapidly for about Follow these steps to arm the vehicle security 16 seconds to indicate that the alarm is being alarm: 1.
GETTING TO KNOW YOUR VEHICLE If the vehicle security alarm is armed and the WARNING! (Continued) battery becomes disconnected, the vehicle security alarm will remain armed when the Before exiting a vehicle, always shift the battery is reconnected; the exterior lights will automatic transmission into PARK, apply flash, and the horn will sound.
GETTING TO KNOW YOUR VEHICLE NOTE: WARNING! (Continued) Passive Entry may be programmed on/off. Do not leave the key fob in or near the Refer to “Uconnect Settings” in “Multimedia” vehicle, or in a location accessible to chil- for further information.
Page 29
GETTING TO KNOW YOUR VEHICLE To Unlock From The Driver's Side: To Unlock From The Passenger Side: inside the vehicle, and no other valid Passive Entry key fobs are detected outside the vehicle, With a valid Passive Entry key fob within 5 ft With a valid Passive Entry key fob within 5 ft the Passive Entry System automatically unlocks (1.5 m) of the driver door handle, grab the front...
Page 30
GETTING TO KNOW YOUR VEHICLE Do NOT grab the door handle when pushing the The LED light on the key fob will not blink if Le présent appareil est conforme aux CNR the key fob battery is low or fully depleted, door handle lock button.
GETTING TO KNOW YOUR VEHICLE Automatic Door Locks — If Equipped For vehicles equipped with a touchscreen radio, refer to “Uconnect Settings” in “Multi- The auto door lock feature default condition is media” for further information. enabled. When enabled, the door locks will lock automatically when the vehicle's speed exceeds NOTE: 15 mph (24 km/h).
GETTING TO KNOW YOUR VEHICLE SEATS Manual Front Seat Recline Adjustment The recline lever is located on the outboard side Seats are a part of the Occupant Restraint of the seat. To recline the seat, lean forward System of the vehicle. slightly, lift the lever, lean back to the desired position and release the lever.
GETTING TO KNOW YOUR VEHICLE 40-20-40 Front Bench Seat — If Equipped Adjusting The Seat Forward Or Rearward WARNING! The seat is divided into three segments. The The seat can be adjusted both forward and rear- Adjusting a seat while driving may be ...
GETTING TO KNOW YOUR VEHICLE Power Lumbar — If Equipped also be programmed to recall the same posi- 2. Adjust all memory profile settings to desired tions when the unlock button is pushed. preferences (i.e., driver’s seat, outside Vehicles equipped with power driver or mirrors, adjustable pedals (if equipped), passenger seats may be also be equipped with NOTE:...
Page 35
GETTING TO KNOW YOUR VEHICLE To program your key fob, perform the following: Memory Position Recall A recall can be cancelled by pushing any of the memory buttons during a recall (S, 1, or 2). 1. Place the vehicle’s ignition in the OFF posi- NOTE: When a recall is canceled, the driver's seat and tion.
GETTING TO KNOW YOUR VEHICLE When you remove the key fob from the igni- Heated Seats — If Equipped Push the heated seat button once to turn tion, the driver’s seat will move to a position the HI setting on. On some models, the front and rear seats may 0.3 inches (7.7 mm) forward of the rear stop be equipped with heaters located in the seat...
GETTING TO KNOW YOUR VEHICLE Rear Heated Seats The front ventilated seats control buttons are Push the heated seat button a third time located on the center instrument panel below to turn the LO setting on. On some models, the two outboard rear seats the touchscreen, and are also located within the are equipped with heated seats.
GETTING TO KNOW YOUR VEHICLE HEAD RESTRAINTS Front Head Restraints To raise the head restraint, pull upward on the head restraint. To lower the head restraint, Four-Way Head Restraints — If Equipped Head restraints are designed to reduce the risk push the adjustment button, located at the Your vehicle may be equipped with front of injury by restricting head movement in the...
GETTING TO KNOW YOUR VEHICLE Rear Head Restraint Removal WARNING! To remove the head restraint, push the adjust- All occupants, including the driver, should ment button and the release button while not operate a vehicle or sit in a vehicle’s pulling upward on the whole assembly.
GETTING TO KNOW YOUR VEHICLE STEERING WHEEL NOTE: WARNING! The engine must be running for the heated Tilt Steering Column Do not adjust the steering column while steering wheel to operate. driving. Adjusting the steering column while This feature allows you to tilt the steering Vehicles Equipped With Remote Start driving or driving with the steering column column upward or downward.
GETTING TO KNOW YOUR VEHICLE DRIVER ADJUSTABLE PEDALS — IF NOTE: For vehicles equipped with Driver Memory Seat, you can use your remote keyless entry EQUIPPED The pedals can be adjusted with the ignition key fob or the memory switch on the driver’s OFF.
GETTING TO KNOW YOUR VEHICLE MIRRORS Automatic Dimming Mirror — If Equipped CAUTION! The mirror head can be adjusted up, down, left, Inside Day/Night Mirror — If Equipped To avoid damage to the mirror during and right for various drivers. The mirror should cleaning, never spray any cleaning solution The mirror head can be adjusted up, down, left, be adjusted to center on the view through the...
GETTING TO KNOW YOUR VEHICLE When the vehicle is placed into reverse gear, a NOTE: Power Mirrors — If Equipped video display illuminates to display the image If your vehicle is equipped with puddle lamps The controls for the power mirrors are located generated by the rear view camera (for the under the outside mirrors, they can be turned on the driver's door trim panel.
GETTING TO KNOW YOUR VEHICLE Using the mirror control switch, push on any of NOTE: the four arrows for the direction that you want If the Power Convex Mirror Switch is not pushed the mirror to move. a second time, the switch will automatically default back to the larger portion of the outside mirrors after a period of time.
GETTING TO KNOW YOUR VEHICLE A small blindspot mirror is located next to main Tilt Side Mirrors In Reverse — If Equipped Outside Mirrors Folding Feature mirror and can be adjusted separately. Tilt Side Mirrors In Reverse provides automatic All outside mirrors are designed to be able to be outside mirror positioning which will aid the manually folded both forward and rearward to driver’s view of the ground rearward of the front...
GETTING TO KNOW YOUR VEHICLE Illuminated Vanity Mirror — If Equipped Headlight Switch Illuminated vanity mirrors are located on each The headlight switch is located on the left side sun visor. To use the mirror, rotate the sun visor of the instrument panel. This switch controls the down and swing the mirror cover upward.
GETTING TO KNOW YOUR VEHICLE Daytime Running Lights (DRLs) Automatic High Beam Headlamp Control — To opt out of the Advanced Auto High Beam Sensitivity Control (default) and enter If Equipped The headlights on your vehicle will illuminate Reduced High Beam Sensitivity Control (not when the engine is started and the transmis- The Automatic High Beam Headlamp Control recommended), on vehicles equipped with...
GETTING TO KNOW YOUR VEHICLE NOTE: Automatic Headlights — If Equipped Directional LED Headlamp System — If The Automatic High Beams will not activate until Equipped This system automatically turns your headlights the vehicle is at or above 12 mph (20 km/h). on or off based on ambient light levels.
GETTING TO KNOW YOUR VEHICLE NOTE: Front Fog Lights — If Equipped light when the lever is moved, it would suggest This feature can be programmed through the that the indicator bulb is defective. To activate the front fog lights, turn on the Uconnect system.
GETTING TO KNOW YOUR VEHICLE The cargo lights will turn on for approximately If the headlights remain on while the ignition is 60 seconds when a key fob unlock button is placed in the OFF position, the exterior lights will pushed, as part of the Illuminated Entry feature.
GETTING TO KNOW YOUR VEHICLE Two types of Rear Courtesy/Reading Lights are Illuminated Entry available for your vehicle: The courtesy lights will turn on when you use the Push button on/off key fob to unlock the doors (if the vehicle is equipped with remote power door locks) or Push lens on/off ...
GETTING TO KNOW YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS pause between cycles, desirable. For maximum mixture that meets or exceeds the temperature delay between cycles, rotate the control knob range of your climate. This rating information Windshield Wipers upward to the first detent. can be found on most washer fluid containers.
GETTING TO KNOW YOUR VEHICLE Rain Sensing Wipers — If Equipped NOTE: Transmission In NEUTRAL Position — When the ignition is ON, and the transmission is in This feature senses moisture on the windshield The Rain Sensing feature will not operate ...
GETTING TO KNOW YOUR VEHICLE Manual Climate Control Overview Manual Climate Controls Icon Description MAX A/C Setting Set the Temperature Control Knob to the MAX A/C setting to change the current setting to the coldest output of air. Moving the temperature control knob away from the MAX A/C setting causes the MAX A/C operation to exit. A/C Button Push the A/C button to engage the Air Conditioning (A/C).
Page 55
GETTING TO KNOW YOUR VEHICLE Icon Description Temperature Control Temperature Control regulates the temperature of the air forced through the Climate Control system. The temperature increases as you turn the temperature control knob clockwise. The temperature decreases as you turn the temperature control knob counterclockwise.
Page 56
GETTING TO KNOW YOUR VEHICLE Icon Description Floor Mode Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. Mix Mode Mix Mode Air is directed through the floor, defrost, and side window demister outlets. This setting works best in cold or snowy conditions that require extra heat to the windshield.
GETTING TO KNOW YOUR VEHICLE Automatic Climate Control Overview Uconnect 4/4C/4C NAV With 8.4–inch Display Automatic Temperature Controls...
Page 58
GETTING TO KNOW YOUR VEHICLE Uconnect 4C NAV With 12–inch Display Automatic Temperature Controls Climate Control Knobs NOTE: Icons and descriptions can vary based upon vehicle equipment. Uconnect 4C/4C NAV With 8.4-inch Display Automatic...
Page 59
GETTING TO KNOW YOUR VEHICLE Icon Description MAX A/C Press and release the MAX A/C button on the touchscreen to change the current setting to the coldest output of air. The MAX A/C indicator illuminates when MAX A/C is on. Pressing the button again will cause the MAX A/C operation to exit. NOTE: The MAX A/C button is only available on the touchscreen.
Page 60
GETTING TO KNOW YOUR VEHICLE Icon Description Faceplate Auto Button AUTO Set your desired temperature and press AUTO. AUTO will achieve and maintain your desired temperature by automatically adjusting the blower speed and air distribution. AUTO mode is highly recommended for efficiency. You can press and release this button on the touchscreen, or push the button on the faceplate, to turn AUTO on.
Page 61
GETTING TO KNOW YOUR VEHICLE Icon Description Faceplate Temperature Driver and Passenger Temperature Up and Down Buttons Knobs Provides the driver and passenger with independent temperature control. Push the red button (or rotate knob if equipped) on the faceplate or touchscreen, or press and slide the temperature bar towards the red arrow button on the touchscreen for warmer temperature settings.
Page 62
GETTING TO KNOW YOUR VEHICLE Icon Description Faceplate Blower Knob Blower Control Blower Control regulates the amount of air forced through the climate system. There are seven blower speeds available. The speeds can be selected using either the blower control knob on the faceplate or the buttons on the touchscreen. Faceplate: The blower speed increases as you turn the blower control knob clockwise from the lowest blower setting.
Page 63
GETTING TO KNOW YOUR VEHICLE Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets.
GETTING TO KNOW YOUR VEHICLE Climate Control Functions MAX A/C Automatic Temperature Control (ATC) MAX A/C sets the control for maximum cooling A/C (Air Conditioning) Automatic Operation performance. The Air Conditioning (A/C) button allows the 1. Push the AUTO button on the faceplate, or Press and release to toggle between MAX A/C operator to manually activate or deactivate the the AUTO button on the touchscreen on the...
GETTING TO KNOW YOUR VEHICLE The temperature can be displayed in U.S. or Summer Operation Window Fogging Metric units by selecting the U.S./Metric The engine cooling system must be protected Vehicle windows tend to fog on the inside in customer-programmable feature.
GETTING TO KNOW YOUR VEHICLE WINDOWS Outside Air Intake CONTROL WEATHER Make sure the air intake, located directly in SETTINGS Power Windows — If Equipped front of the windshield, is free of obstructions, Warm Weather Turn on and set such as leaves. Leaves collected in the air Power Window Controls the mode control to intake may reduce airflow, and if they enter the...
Page 67
GETTING TO KNOW YOUR VEHICLE NOTE: To stop the window from going all the way down during auto closure. If this happens, pull the The Key Off Power Delay feature will allow the during the Auto-Down operation, pull up on the switch lightly to the first detent and hold to close power windows to operate for up to 10 minutes switch briefly.
GETTING TO KNOW YOUR VEHICLE Window Lockout Switch — If Equipped rear windows open, open the front and rear windows together to minimize the buffeting. If The window lockout switch on the driver's door the buffeting occurs with the sunroof open, allows you to disable the window control on the adjust the sunroof opening to minimize the rear passenger doors.
GETTING TO KNOW YOUR VEHICLE 2. Reach into the opening beneath the center NOTE: CAUTION! of the hood and push the safety latch lever HomeLink® is disabled when the Vehicle Secu- to the left to release it, before raising the To prevent possible damage, do not slam the rity Alarm is active.
GETTING TO KNOW YOUR VEHICLE NOTE: NOTE: Only use this transceiver with a garage door Erasing all channels should only be opener that has a “stop and reverse” feature as performed when programming HomeLink® required by federal safety standards. This for the first time.
Page 71
GETTING TO KNOW YOUR VEHICLE 4. Continue to hold both buttons and observe NOTE: 2. Place the hand-held transmitter 1 to the indicator light. The HomeLink® indi- If the garage door opener/device does not acti- 3 inches (3 to 8 cm) away from the Home- cator will flash slowly and then rapidly after vate, push the button a third time (for two Link®...
GETTING TO KNOW YOUR VEHICLE Reprogramming A Single HomeLink® Button It may be helpful to unplug the device during the 5. Press and hold the programmed Home- (Non-Rolling Code) cycling process to prevent possible overheating Link® button and observe the indicator of the garage door or gate motor.
GETTING TO KNOW YOUR VEHICLE 2. Press and hold the desired HomeLink® The HomeLink® Universal Transceiver is WARNING! button until the indicator light begins to disabled when the Vehicle Security Alarm is flash after 20 seconds. Do not release the active.
GETTING TO KNOW YOUR VEHICLE General Information La operación de este equipo está sujeta a las siguientes dos condiciones: The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this 1. es posible que este equipo o dispositivo no vehicle: cause interferencia perjudicial y This device complies with Part 15 of the FCC...
Page 75
GETTING TO KNOW YOUR VEHICLE Door Storage WARNING! Front Door Storage — If Equipped This armrest is not a seat. Anyone seated Storage areas and bottle holders (driver’s side on the armrest could be seriously injured only) are located in the door trim panels. during vehicle operation, or a collision.
Page 76
GETTING TO KNOW YOUR VEHICLE With the upper lid closed, pull on the lower Premium Center Console — If Equipped handle to open the lower storage bin. The lower The premium center console is equipped with bin contains a power inverter outlet located in two front storage bins located in front of the the front portion of the lower bin.
Page 77
GETTING TO KNOW YOUR VEHICLE With the center console lid open, push the release button at the front of the cupholder bin to slide tray rearward for access to the front lower storage bin. Slide forward to access the rear lower storage bin. Front Bench Seat Storage Storage Drawer There is a storage drawer located in the lower...
Page 78
GETTING TO KNOW YOUR VEHICLE Storage Bin (Regular Cab) Unfolding The Load Floor/Crew Cab 3. Lift the front panel until the load floor unfolds into position. The storage bin is located behind the front 1. Lift the 60/40 seat cushion(s) to the seats and runs the length of the cab.
GETTING TO KNOW YOUR VEHICLE Below Rear Seat Storage (Crew Cab) Cupholders WARNING! The Crew Cab models provide additional Front Seat Cupholders Do not drive with the load floor in the up storage under the rear seats. Lift the seats to For vehicles equipped with a center console, position.
GETTING TO KNOW YOUR VEHICLE Vehicles Equipped With 40/20/40 Seats Electrical Power Outlets The cupholders are located on the backside of The auxiliary 12 Volt (13 Amp) power outlet can the center portion of the front seat (20). Fold provide power for in-cab accessories designed down the center section of the front seat to gain for use with the standard “cigar lighter”...
Page 81
GETTING TO KNOW YOUR VEHICLE An auxiliary power outlet can be found in the When the vehicle is turned off, be sure to CAUTION! tray on top of the center stack. This power outlet unplug any equipment as to not drain the works when the ignition is in the ON/RUN, ACC, battery of the vehicle.
GETTING TO KNOW YOUR VEHICLE Power Inverter — If Equipped All power inverters are designed with built-in phones, electronics and other low power overload protection. If the power rating of 400 devices requiring power up to 400 Watts. If equipped, a 115 Volt (400 Watts Maximum) Watts is exceeded, the power inverter shuts Certain high-end video game consoles exceed inverter may be located inside the center...
GETTING TO KNOW YOUR VEHICLE wirelessly charge your Qi enabled mobile Overhead Sunglass Storage WARNING! phone. Qi is a standard that uses magnetic At the front of the overhead console, a compart- To avoid serious injury or death: induction to transfer power to your mobile ment is provided for the storage of one pair of device.
GETTING TO KNOW YOUR INSTRUMENT PANEL Base / Midline Instrument Cluster 3. Instrument Cluster Display 4. Oil Pressure Gauge Descriptions When the appropriate conditions exist, The pointer should always indicate the oil this display shows the instrument cluster pressure when the engine is running.
Page 86
GETTING TO KNOW YOUR INSTRUMENT PANEL 6. Fuel Gauge 7. Temperature Gauge WARNING! The pointer shows the level of fuel in the The gauge pointer shows engine coolant A hot engine cooling system is dangerous. fuel tank when the ignition is in the ON/ temperature.
GETTING TO KNOW YOUR INSTRUMENT PANEL Premium Instrument Cluster Descriptions 4. Fuel Gauge WARNING! The pointer shows the level of fuel in the 1. Tachometer A hot engine cooling system is dangerous. fuel tank when the ignition is in the ON/ Indicates the engine speed in revolutions ...
GETTING TO KNOW YOUR INSTRUMENT PANEL DIESEL INSTRUMENT CLUSTER 3. Instrument Cluster Display WARNING! When the appropriate conditions exist, 1. Tachometer A hot engine cooling system is dangerous. this display shows the instrument cluster Indicates the engine speed in revolutions ...
Page 91
GETTING TO KNOW YOUR INSTRUMENT PANEL 5. Speedometer 7. Diesel Exhaust Fluid (DEF) Gauge NOTE: Indicates vehicle speed. The DEF Gauge displays the actual level The gauge may take up to five seconds to of Diesel Exhaust Fluid in the DEF tank. update after adding a gallon or more of 6.
GETTING TO KNOW YOUR INSTRUMENT PANEL Diesel INSTRUMENT CLUSTER Refer to “Refueling The Vehicle — Diesel NOTE: Engine” in “Starting And Operating” for 1. Tachometer The DEF tank on these vehicles is designed further information. with a large amount of full reserve. So the Indicates the engine speed in revolutions ...
GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY Instrument Cluster Display Controls The instrument cluster display menu items may consist of the following: The instrument cluster display features a Your vehicle will be equipped with an instru- Speedometer driver-interactive display that is located in the ment cluster display, which offers useful infor- instrument cluster.
GETTING TO KNOW YOUR INSTRUMENT PANEL The system allows the driver to select informa- Right Arrow Button NOTE: tion by pushing the following instrument cluster Use the steering wheel instrument cluster Push and release the right arrow display control buttons located on the left side display controls for the following procedure.
GETTING TO KNOW YOUR INSTRUMENT PANEL Secondary Method Of Resetting Engine Oil Life Speedometer Oil Life Push and release the up or down arrow button Fuel Filter Life — If Equipped 1. Without pressing the brake pedal, push the ...
Page 97
GETTING TO KNOW YOUR INSTRUMENT PANEL Adaptive Cruise Control Ready Fuel Economy Trailer Tow When ACC is activated but the vehicle speed Push and release the up or down arrow button Push and release the up or down arrow button setting has not been selected, the display will until the Fuel Economy menu item is highlighted until the Trailer Tow menu item is highlighted in...
Page 98
GETTING TO KNOW YOUR INSTRUMENT PANEL Phone Call Status feature allows you to change what information Vehicle Settings — If Equipped is displayed in the instrument cluster as well as When a call is incoming, a Phone Call Status Commercial Settings —...
Page 99
GETTING TO KNOW YOUR INSTRUMENT PANEL Coolant Temperature — If Equipped Trailer Trip Oil Temperature — If Equipped Oil Temperature — If Equipped Audio Battery Voltage — If Equipped Battery Voltage — If Equipped Speedometer (Default Setting) Transmission Temperature —...
Page 100
GETTING TO KNOW YOUR INSTRUMENT PANEL Right Side — If Equipped Trip B Distance Current MPG None Trailer Trip Trip A Distance Range (Default Setting) Trailer Brake Trip B Distance Average MPG ...
Page 101
GETTING TO KNOW YOUR INSTRUMENT PANEL Settings — If Equipped Follow the prompts to display and set any of the If equipped with a base radio (Non-Touch- following Vehicle Settings. screen) Vehicle Settings will be included in Personal Settings allows the driver to set and the instrument cluster display.
Page 102
GETTING TO KNOW YOUR INSTRUMENT PANEL Setting Names Abbreviated Setting Names SubMenus (Right Submenu Layer) (Left Submenu Layer) Auto Lock Doors Auto Lock Doors On; Off Auto Unlock Doors Auto Unlock Doors On; Off Sound Horn with Remote Start Horn w/ Rmt Start On;...
Page 103
GETTING TO KNOW YOUR INSTRUMENT PANEL Setting Names Abbreviated Setting Names SubMenus (Right Submenu Layer) (Left Submenu Layer) Trailer # (# is equal to slot position) Boat Cargo Dump Equipment Flatbed Trailer Name Trailer Name Gooseneck ...
Page 104
GETTING TO KNOW YOUR INSTRUMENT PANEL Setting Names Abbreviated Setting Names SubMenus (Right Submenu Layer) (Left Submenu Layer) Compass Variance Compass Var 1-15 increments of 1 Calibrate Compass Compass Cal Cancel; Calibrate Fuel Saver Display Fuel Saver On; Off Commercial Settings — If Equipped NOTE: Commercial Settings allows you to access the If your vehicle is equipped with a touchscreen...
GETTING TO KNOW YOUR INSTRUMENT PANEL Diesel Messages And Warnings — 6.7L Your vehicle has the ability to alert you to addi- remove the trapped PM. If this occurs, the tional maintenance required on your vehicle or “Exhaust Filter XX% Full Safely Drive at Cummins Diesel Engine Highway Speeds to Remedy”...
Page 106
GETTING TO KNOW YOUR INSTRUMENT PANEL Exhaust Service Required — See Dealer Now NOTE: Engine Power Reduced Up To 30 Sec — This message indicates regeneration has (Seconds) During Warmup — This message Failing to follow the oil change indicator, been disabled due to a system malfunction.
Page 107
GETTING TO KNOW YOUR INSTRUMENT PANEL Diesel Exhaust Fluid (DEF) Warning Speed Limited to 5 MPH in XXX mi Refill DEF NOTE: — This message will continuously display if A minimum of 2 gallons (7.5 Liters) may be Messages the “DEF Low Refill Soon”...
Page 108
GETTING TO KNOW YOUR INSTRUMENT PANEL Service DEF System See Dealer — This value where it stopped when a previous fault NOTE: message will display when the fault is initially was temporarily remedied, or at a minimum of When this message is displayed, the engine can detected, each time the vehicle is started, 50 miles (80 km).
GETTING TO KNOW YOUR INSTRUMENT PANEL Battery Saver On/Battery Saver Mode NOTE: Loss of the battery charge may indicate one or more of the following conditions: Message — Electrical Load Reduction The charging system is independent from Actions — If Equipped The charging system cannot deliver enough ...
GETTING TO KNOW YOUR INSTRUMENT PANEL The battery was discharged by an electrical After a trip: Red Warning Lights load left on when the vehicle was parked. Check if any aftermarket equipment was Seat Belt Reminder Warning Light installed (additional lights, upfitter electrical The battery was used for an extended period ...
Page 111
GETTING TO KNOW YOUR INSTRUMENT PANEL Brake Warning Light the brake fluid level in the master cylinder has Operation of the Brake Warning Light can be dropped below a specified level. checked by turning the ignition switch from the This warning light monitors various OFF position to the ON/RUN position.
Page 112
GETTING TO KNOW YOUR INSTRUMENT PANEL Vehicle Security Warning Light — If Equipped Battery Charge Warning Light Oil Temperature Warning Light This light will flash at a fast rate for This warning light will illuminate when This warning light will illuminate to approximately 15 seconds when the the battery is not charging properly.
GETTING TO KNOW YOUR INSTRUMENT PANEL If the light continues to flash when the vehicle is Trailer Brake Disconnected Warning Light CAUTION! running, immediate service is required and you This warning light will illuminate when may experience reduced performance, an Continuous driving with the Transmission the Trailer Brake has been discon- elevated/rough idle, or engine stall and your...
Page 114
GETTING TO KNOW YOUR INSTRUMENT PANEL Engine Check/Malfunction Indicator Warning vated. It should go out with the engine running. WARNING! Light (MIL) If the “ESC Indicator Light” comes on continu- A malfunctioning catalytic converter, as ously with the engine running, a malfunction The Engine Check/Malfunction Indi- referenced above, can reach higher has been detected in the ESC system.
Page 115
GETTING TO KNOW YOUR INSTRUMENT PANEL Low Washer Fluid Warning Light — If light. If the light does not turn off, please see an by the vehicle manufacturer on the vehicle authorized dealer. placard or tire inflation pressure label. If your Equipped vehicle has tires of a different size than the size This warning light will illuminate when...
Page 116
GETTING TO KNOW YOUR INSTRUMENT PANEL Your vehicle has also been equipped with a conventional brake system will continue to CAUTION! TPMS malfunction indicator to indicate when operate normally, assuming the Brake Warning the system is not operating properly. The TPMS The TPMS has been optimized for the original Light is not also on.
GETTING TO KNOW YOUR INSTRUMENT PANEL Speed Control Fault Warning Light Trailer Merge Assist Indicator Light — If forcing the front and rear wheels to rotate at the same speed. Equipped This warning light will illuminate to Refer to “Four-Wheel Drive Operation” in indicate the Speed Control System This indicator light will illuminate to “Starting And Operating”...
GETTING TO KNOW YOUR INSTRUMENT PANEL NEUTRAL Indicator Light — If Equipped Low Diesel Exhaust Fluid (DEF) Indicator before you drain the water from the fuel filter to Light — If Equipped prevent engine damage. This light alerts the driver that the Refer to the “Draining Fuel/Water Separator 4WD power transfer case is in the The Low Diesel Exhaust Fluid (DEF)
GETTING TO KNOW YOUR INSTRUMENT PANEL ECO Mode Indicator Light — If Equipped NOTE: Refer to “Diesel Exhaust Brake (Engine Braking)” in “Starting And Operating” for further This light will turn on when ECO Mode A continuous chime will sound if the vehicle is ...
GETTING TO KNOW YOUR INSTRUMENT PANEL Blue Indicator Lights If any of these systems require service, the OBD access this information to assist with the diag- II system will turn on the Malfunction Indicator nosis and service of your vehicle and emissions High Beam Indicator Light Light (MIL).
GETTING TO KNOW YOUR INSTRUMENT PANEL EMISSIONS INSPECTION AND 1. Cycle the ignition switch to the ON position, If your OBD II system is not ready, you should but do not crank or start the engine. see an authorized dealer or repair facility. If your MAINTENANCE PROGRAMS vehicle was recently serviced or had a battery NOTE:...
SAFETY SAFETY FEATURES You also may experience the following when WARNING! (Continued) ABS activates: Anti-Lock Brake System (ABS) Pumping of the Anti-Lock Brakes will The ABS motor noise (it may continue to run diminish their effectiveness and may lead for a short time after the stop) The Anti-Lock Brake System (ABS) provides to a collision.
SAFETY ABS is designed to function with the Original (EBD), Anti-Lock Brake System (ABS), Brake If the “Brake System Warning Light” remains on Equipment Manufacturer (OEM) tires. Modifica- Assist System (BAS), Hill Start Assist (HSA), or comes on while driving, it indicates that the tion may result in degraded ABS performance.
Page 124
SAFETY The following conditions must be met in order WARNING! WARNING! for HSA to activate: The Brake Assist System (BAS) cannot There may be situations where the Hill Start The feature must be enabled. prevent the natural laws of physics from Assist (HSA) will not activate and slight rolling The vehicle must be stopped.
Page 125
SAFETY Towing With HSA Disabling And Enabling HSA 5. Rotate the steering wheel slightly more than one-half turn to the left. HSA will also provide assistance to mitigate roll This feature can be turned on or turned off. To back while towing a trailer. change the current setting, proceed as follows: 6.
Page 126
SAFETY Traction Control System (TCS) ESC uses sensors in the vehicle to determine WARNING! the vehicle path intended by the driver and The Traction Control System (TCS) monitors the compares it to the actual path of the vehicle. Electronic Stability Control (ESC) cannot ...
Page 127
SAFETY ESC Operating Modes NOTE: WARNING! (Continued) For vehicles with multiple partial ESC modes a NOTE: momentary button push will toggle the ESC Vehicle modifications, or failure to properly Depending upon model and mode of operation, mode. Multiple momentary button pushes may maintain your vehicle, may change the the ESC system may have multiple operating handling characteristics of your vehicle,...
Page 128
SAFETY Full Off — If Equipped ESC Activation/Malfunction Indicator Light WARNING! And ESC OFF Indicator Light This mode is intended for off-highway or In the ESC “Full Off” mode, the engine off-road use only and should not be used on any The “ESC Activation/Malfunction Indi- torque reduction and stability features are public roadways.
Page 129
SAFETY NOTE: brake and may also reduce engine power to Trailer Sway Control (TSC) lessen the chance that wheel lift will occur. ERM Trailer Sway Control (TSC) uses sensors in the The “ESC Activation/Malfunction Indicator can only reduce the chance of wheel lift occur- vehicle to recognize an excessively swaying Light”...
Page 130
SAFETY Hill Descent Control (HDC) — If Equipped Activating HDC 8th = 5.0 mph (8 km/h) Once HDC is enabled it will activate automati- Hill Descent Control (HDC) is intended for low 9th = 5.6 mph (9 km/h) – If Equipped ...
SAFETY AUXILIARY DRIVING SYSTEMS Disabling HDC The cluster icon and switch lamp will flash for several seconds then extinguish when the HDC will be deactivated and disabled if any of Forward Collision Warning (FCW) With driver pushes the HDC switch but enable the following conditions occur: conditions are not met.
Page 132
SAFETY If the driver does not take action based upon The FCW system is intended for on-road use only. If the vehicle is taken off-road, the FCW these progressive warnings, then the system will provide a limited level of active braking to system should be deactivated to prevent unnecessary warnings to the surroundings.
Page 133
SAFETY NOTE: FCW Braking Status And Sensitivity Near The FCW sensitivity and Active Braking status When the sensitivity of FCW is set to the When the FCW is “on”, this allows the system are programmable through the Uconnect to warn the driver of a possible collision with “Near”...
SAFETY Service FCW Warning Le présent appareil est conforme aux CNR Tire Pressure Monitoring System (TPMS) d`Innovation, Science and Economic Develop- If the system turns off, and the instrument (Vehicles Under 10K GVWR Only) ment applicables aux appareils radio exempts cluster displays: The Tire Pressure Monitoring System (TPMS) de licence.
Page 135
SAFETY cold tire inflation pressure must not exceed the NOTE: CAUTION! maximum inflation pressure molded into the When filling warm tires, the tire pressure may tire sidewall. Refer to “Tires” in “Servicing And need to be increased up to an additional 4 psi The TPMS has been optimized for the orig- ...
Page 136
SAFETY NOTE: Various tire pressure monitoring system messages, which display in the instrument The TPMS is not intended to replace normal cluster tire care and maintenance or to provide warning of a tire failure or condition. Tire Pressure Monitoring System Warning ...
Page 137
SAFETY Should this occur, you should stop as soon as Service TPMS Warning Accumulation of snow or ice around the possible and inflate the tires with a low pressure wheels or wheel housings. If a system fault is detected, the “Tire Pressure condition (those in a different color in the instru- Monitoring Warning Light”...
Page 138
SAFETY Vehicles With Non Matching Full Size Spare Or For each subsequent ignition switch cycle, a target tire pressure value, through TTPMS chime will sound, the TPMS Warning Light will Compact Spare settings found in the radio. flash on and off for 75 seconds and then The non matching full size spare or compact The TTPMS monitors the pressure of each tire ...
Page 139
SAFETY Trailer Tire Pressure Sensor Pairing touchscreen will allow you to retry the proce- dure; “Retry” will only appear when setup fails. In order use this feature, the provided tire pres- Each tire must be successfully paired during a sure sensors must be installed in the desired single pairing process to receive the success trailer tires and the sensors must be paired to screen.
Page 140
SAFETY Should this occur, you should stop as soon as Trailer Tire Pressure System Not Configured Tire Fill Alert — If Equipped possible and inflate the tires with a low pressure A “Trailer Tire Pressure System Not Configured” This feature notifies the user when the placard condition (those in a different color in the instru- message will be displayed in the Instrument tire pressure is attained while inflating or...
Page 141
SAFETY The hazard lamps will come on to confirm the Selectable Tire Fill Alert (STFA) — If Equipped NOTE: vehicle is in Tire Fill Alert mode. The STFA system will only support inflating or The Selectable Tire Fill Alert (STFA) system is an deflating one tire at a time.
Page 142
SAFETY Tire Pressure Information System (TPIS) If a system fault is detected, the instrument General Information 3500/4500/5500 Series Trucks cluster will display a "SERVICE TPM SYSTEM" The following regulatory statement applies to all message for a minimum of five seconds and Your vehicle may be equipped with a Tire Pres- Radio Frequency (RF) devices equipped in this then display dashes (- -) in place of the pressure...
SAFETY La operación de este equipo está sujeta a las Some of the safety features described in this 3. If a child from 2 to 12 years old (not in a siguientes dos condiciones: section may be standard equipment on some rear-facing child restraint) must ride in the models, or may be optional equipment on front passenger seat, move the seat as far...
SAFETY 9. If the air bag system in this vehicle needs to Research has shown that seat belts save lives, Seat Belt Reminder Light will turn on and be modified to accommodate a disabled and they can reduce the seriousness of injuries remain on until both outboard front seat belts person, refer to the “Customer Assistance”...
Page 145
SAFETY Change Of Status NOTE: WARNING! If BeltAlert has been deactivated and the driver If the driver or outboard front seat passenger (if or outboard front seat passenger (if equipped Relying on the air bags alone could lead to equipped with outboard front passenger seat ...
Page 146
SAFETY WARNING! WARNING! (Continued) WARNING! (Continued) A lap belt worn too high can increase the Be sure everyone in your vehicle is in a seat A seat belt that is worn under your arm is risk of injury in a collision. The seat belt and using a seat belt properly.
Page 147
SAFETY Lap/Shoulder Belt Operating Instructions 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until 1. Enter the vehicle and close the door. Sit you hear a “click.” back and adjust the seat. 2.
Page 148
SAFETY Lap/Shoulder Belt Untwisting Procedure WARNING! Use the following procedure to untwist a twisted Wearing your seat belt incorrectly could lap/shoulder belt. make your injuries in a collision much 1. Position the latch plate as close as worse. You might suffer internal injuries, or possible to the anchor point.
Page 149
SAFETY First Row Center Seat Belt Operating 6. When the seat belt is long enough to fit, insert the latch plate into the buckle until Instructions (Regular Cab Only) you hear a “click.” The first row center seat belt (Regular Cab only) features a seat belt with a mini-latch plate and 7.
Page 150
SAFETY 10. To disengage the mini-latch plate from the Seat Belt Extender WARNING! (Continued) mini-buckle for storage, insert the regular If a seat belt is not long enough to fit properly, latch plate into the center red slot on the When reattaching the mini-latch plate and ...
Page 151
SAFETY Seat Belts And Pregnant Women a collision. These devices may improve the Switchable Automatic Locking Retractors performance of the seat belt by removing slack (ALR) — If Equipped from the seat belt early in a collision. Preten- The seat belts in the passenger seating posi- sioners work for all size occupants, including tions may be equipped with a Switchable Auto- those in child restraints.
Page 152
SAFETY Use the Automatic Locking Mode anytime a 3. Allow the seat belt to retract. As the seat child restraint is installed in a seating position belt retracts, you will hear a clicking sound. that has a seat belt with this feature. Children This indicates the seat belt is now in the 12 years old and under should always be prop- Automatic Locking Mode.
SAFETY Supplemental Restraint Systems (SRS) Front and Side Impact Sensors — If Equipped The ORC also includes diagnostics that will illu- minate the instrument panel Air Bag Warning Some of the safety features described in this Seat Belt Pretensioners — If Equipped ...
Page 154
SAFETY WARNING! WARNING! (Continued) Ignoring the Air Bag Warning Light in your Never install a rear-facing child restraint in instrument panel could mean you won’t have the front seat of a vehicle. Only use a the air bag system to protect you in a rear-facing child restraint in the rear seat.
Page 155
SAFETY This vehicle may be equipped with a driver and/ Because air bag sensors measure vehicle WARNING! (Continued) or front passenger seat belt buckle switch that deceleration over time, vehicle speed and detects whether the driver or front passenger damage by themselves are not good indicators Relying on the air bags alone could lead to ...
Page 156
SAFETY Knee Impact Bolsters Supplemental Seat-Mounted Side Air Bags When the SAB deploys, it opens the seam on (SABs) are located in the outboard side of the the outboard side of the seatback’s trim cover. The Knee Impact Bolsters help protect the front seats.
Page 157
SAFETY Supplemental Side Air Bag Inflatable Curtains in the area where the SABICs inflate. Children Side Impacts (SABICs) are located above the side windows. are at an even greater risk of injury from a The Side Air Bags are designed to activate in The trim covering the SABICs is labeled “SRS deploying air bag.
Page 158
SAFETY Side Air Bags are a supplement to the seat belt Rollover Events (If Equipped With Rollover WARNING! restraint system. Side Air Bags deploy in less Sensing) — If Equipped time than it takes to blink your eyes. Side Air Bags need room to inflate. Do not ...
Page 159
SAFETY Air Bag System Components NOTE: For nose or throat irritation, move to fresh air. Front and/or side air bags will not deploy in all If the irritation continues, see your doctor. If NOTE: these particles settle on your clothing, follow collisions.
Page 160
SAFETY Enhanced Accident Response System Cut off battery power to the: Enhanced Accident Response System Reset Procedure In the event of an impact, if the communication Engine network remains intact, and the power remains In order to reset the Enhanced Accident Electric Motor (if equipped) ...
Page 161
SAFETY Event Data Recorder (EDR) NOTE: WARNING! (Continued) EDR data are recorded by your vehicle only if a This vehicle is equipped with an Event Data non-trivial crash situation occurs; no data are It is dangerous to try to repair any part of ...
SAFETY Child Restraints There are different sizes and types of restraints NOTE: for children from newborn size to the child Everyone in your vehicle needs to be buckled up For additional information, refer to http:// almost large enough for an adult safety belt. at all times, including babies and children.
Page 163
SAFETY Summary Of Recommendations For Restraining Children In Vehicles Child Size, Height, Weight Or Age Recommended Type Of Child Restraint Children who are two years old or younger and Either an Infant Carrier or a Convertible Child Infants and Toddlers who have not reached the height or weight limits Restraint, facing rearward in a rear seat of the of their child restraint...
Page 164
SAFETY Infant And Child Restraints WARNING! WARNING! Safety experts recommend that children ride Never place a rear-facing child restraint in Do not install a rear-facing car seat using a rear-facing in the vehicle until they are two years front of an air bag. A deploying passenger rear support leg in this vehicle.
Page 165
SAFETY Older Children And Child Restraints All children whose weight or height is above the WARNING! forward-facing limit for the child seat should use Children who are two years old or who have a belt-positioning booster seat until the Improper installation can lead to failure of ...
Page 166
SAFETY Children Too Large For Booster Seats If the answer to any of these questions was “no, WARNING! ” then the child still needs to use a booster seat Children who are large enough to wear the in this vehicle. If the child is using the lap/ Never allow a child to put the shoulder belt shoulder belt comfortably, and whose legs are shoulder belt, check seat belt fit periodically...
Page 167
SAFETY Recommendations For Attaching Child Restraints Use Any Attachment Method Shown With An “X” Below Combined Weight of LATCH – Lower Restraint Type the Child + Child LATCH – Lower Seat Belt + Top Seat Belt Only Anchors + Top Tether Restraint Anchors Only Tether Anchor...
Page 168
SAFETY LATCH Positions For Installing Child Restraints In This Vehicle Regular Cab LATCH Positions Crew Cab 60/40 Split Bench LATCH Positions Crew Cab Full Bench LATCH Positions Top Tether Anchorage Symbol Lower Anchorage Symbol (2 Anchorages Per Lower Anchorage Symbol (2 Anchorages Per Seating Position) Seating Position) Top Tether Anchorage Symbol...
Page 169
SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Use the LATCH anchorage system until the combined weight of the child and the child What is the weight limit (child’s weight + weight restraint is 65 lbs (29.5 kg). Use the seat belt of the child restraint) for using the LATCH 65 lbs (29.5 kg) and tether anchor instead of the LATCH system...
Page 170
SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Never “share” a LATCH anchorage with two or more child restraints. If the center position does Can two child restraints be attached using a not have dedicated LATCH lower anchorages, common lower LATCH anchorage? use the seat belt to install a child seat in the center position next to a child seat using the...
Page 171
SAFETY Locating The LATCH Anchorages — Crew Cab Only The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat Regular Cab Tether Anchorages (Behind Covers)
Page 172
SAFETY Center Seat LATCH Crew Cab Split Bench Rear Seat: Center LATCH To Install A LATCH-Compatible Child Anchorages Available Restraint Regular Cab or Crew Cab Full Bench Rear Seat: If a child restraint installed in the center posi- No Lower Center LATCH Anchorages Available If the selected seating position has a Switch- tion blocks the seat belt webbing or buckle for able Automatic Locking Retractor (ALR) seat...
Page 173
SAFETY 3. Attach the lower hooks or connectors of the How To Stow An Unused Switchable-ALR WARNING! (Continued) child restraint to the lower anchorages in (ALR) Seat Belt: the selected seating position. Child restraint anchorages are designed to When using the LATCH attaching system to withstand only those loads imposed by install a child restraint, stow all ALR seat belts 4.
Page 174
SAFETY The seat belts in the passenger seating posi- Lap/Shoulder Belt Systems For Installing tions are equipped with either a Switchable Child Restraints In This Vehicle Automatic Locking Retractor (ALR) or a cinching latch plate or both. Both types of seat belts are designed to keep the lap portion of the seat belt tight around the child restraint so that it is not necessary to use a locking clip.
Page 175
SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit (child’s Always use the tether anchor when weight + weight of the child using the seat belt to install a restraint) for using the Tether Weight limit of the Child Restraint forward facing child restraint, up to Anchor with the seat belt to attach...
Page 176
SAFETY Installing A Child Restraint With A Switchable For Regular Cab Models 7. Finally, pull up on any excess webbing to Automatic Locking Retractor (ALR): tighten the lap portion around the child Place the child seat in the center of the restraint while you push the child restraint Child restraint systems are designed to be seating position.
Page 177
SAFETY Installing A Child Restraint With A Cinching 2. Next, pull enough of the seat belt webbing Any seat belt system will loosen with time, so from the retractor to pass it through the belt check the belt occasionally, and pull it tight if Latch Plate (CINCH) —...
Page 178
SAFETY Installing Child Restraints Using The Top Regular Cab Trucks: 2. Route the tether strap to provide the most Tether Anchorage direct path between the anchorage and the In the regular cab truck, the top tether child seat. The tether strap should go anchorages are located behind the center and WARNING! between the head restraint posts under-...
Page 179
SAFETY Crew Cab Trucks The top tether anchorages in this vehicle are tether strap loops located between the rear glass and the back of the rear seat. There is a tether strap loop located behind each seating position. Follow the steps below to attach the tether strap of the child restraint.
Page 180
SAFETY NOTE: 2. Place a child restraint on the seat and 4. Attach the hook to the outboard tether strap If there are child seats in both of the outboard adjust the tether strap so that it will reach loop (see diagram). Tighten the tether strap (left and right) seating positions, the tether over the seat back, under the head according to the child seat manufacturer’s...
SAFETY Installing Three Child Restraints: Transporting Pets Air Bags deploying in the front seat could harm 1. Place a child restraint on each outboard your pet. An unrestrained pet will be thrown rear seat. Route the tether straps following about and possibly injured, or injure a the directions for right and left seating passenger during panic braking or in a collision.
SAFETY SAFETY TIPS Exhaust Gas Whenever a change is noticed in the sound of the exhaust system, when exhaust fumes can Transporting Passengers WARNING! be detected inside the vehicle, or when the underside or rear of the vehicle is damaged, NEVER TRANSPORT PASSENGERS IN THE Exhaust gases can injure or kill.
Page 183
SAFETY Air Bag Warning Light Floor Mat Safety Information WARNING! (Continued) Always use floor mats designed to fit your The Air Bag warning light will turn on for four ALWAYS REMOVE THE EXISTING FLOOR vehicle. Only use a floor mat that does not inter- to eight seconds as a bulb check when the igni- MAT FROM THE VEHICLE before...
SAFETY Periodic Safety Checks You Should Make Door Latches WARNING! (Continued) Outside The Vehicle Check for proper closing, latching, and locking. ALWAYS make sure objects cannot fall or Tires Fluid Leaks slide into the driver’s side floor area when Examine tires for excessive tread wear and the vehicle is moving.
STARTING AND OPERATING STARTING THE ENGINE — GAS ENGINE NOTE: WARNING! (Continued) This vehicle is equipped with a transmission Before starting your vehicle, adjust your seat, Do not leave the key fob in or near the shift interlocking system. The brake pedal adjust both inside and outside mirrors, and vehicle, or in a location accessible to chil- must be pressed to shift out of PARK.
STARTING AND OPERATING Keyless Enter-N-Go — Ignition 3. The system takes over and attempts to start 3. If the gear selector is not in PARK, the the vehicle. If the vehicle fails to start, the ENGINE START/STOP button must be held starter will disengage automatically after for two seconds or three short pushes in a 10 seconds.
Page 187
STARTING AND OPERATING ENGINE START/STOP Button Functions — With The conditions under which AutoPark will Vehicle is not in PARK Driver’s Foot OFF The Brake Pedal (In PARK Or engage are outlined on the following pages. Vehicle speed is 1.2 mph (1.9 km/h) or less ...
Page 188
STARTING AND OPERATING The message “ AutoPark Engaged Shift to P 4WD LOW — If Equipped engine is cranking. This should clear any excess then Shift to Gear” will display in the instrument fuel in case the engine is flooded. AutoPark will be disabled when operating the cluster.
STARTING AND OPERATING After Starting CAUTION! WARNING! (Continued) The idle speed is controlled automatically, and To prevent damage to the starter, do not Never leave children alone in a vehicle, or it will decrease as the engine warms up. crank the engine for more than 10 seconds at with access to an unlocked vehicle.
STARTING AND OPERATING Tip Start Feature Normal Starting Under cold weather conditions, the engine may not immediately crank if the "Wait to Do not press the accelerator. Place the ignition Using The ENGINE START/STOP Button Start" telltale is illuminated. This is normal switch briefly to the START position and release operation.
Page 191
STARTING AND OPERATING 4. If the gear selector is in NEUTRAL, and the ENGINE START/STOP Button Functions — With Keyless Enter-N-Go Starting Procedure — vehicle speed below 5 mph (8 km/h), Driver’s Foot OFF The Brake Pedal (In PARK Or Engine Manifold Air Temperature 0°F To pushing the ENGINE START/STOP button NEUTRAL Position)
STARTING AND OPERATING 3. While the "Wait to Start" telltale is on, the 5. After engine start-up, check to see that Extreme Cold Weather instrument cluster will additionally display a there is oil pressure. The Cummins Turbo Diesel engine is equipped gauge or bar whose initial length represents with several features designed to assist cold 6.
STARTING AND OPERATING Normal Starting Procedure — Engine 4. Place the ignition switch in the START posi- Starting Procedure — Engine Manifold Air tion and crank the engine. Do not press the Manifold Air Temperature Above 66°F Temperature 0°F To 66°F (–18°C to 19°C) accelerator during starting.
STARTING AND OPERATING NOTE: Starting Procedure — Engine Manifold Air CAUTION! Temperature Below 0°F (-18°C) Engine idle speed will automatically increase If the “Water in Fuel Indicator Light” remains In extremely cold weather below 0°F (-18°C) it to 1,000 RPM and engage the Variable on, DO NOT START the engine before you may be beneficial to cycle the intake air heater Geometry Turbocharger at low coolant...
STARTING AND OPERATING 1. If the engine stalls after the initial start, the NOTE: Starting Fluids ignition must be turned to the OFF position Engine idle speed will automatically increase WARNING! for at least five seconds and then to the ON to 1,000 RPM and engage the Variable position to recycle the intake air heater.
STARTING AND OPERATING NORMAL OPERATION — DIESEL ENGINE The cycling action will cause temporary WARNING! dimming of the headlamps, interior lamps, and Observe the following when the engine is oper- also a noticeable reduction in blower motor Do not leave children or animals inside ...
Page 197
STARTING AND OPERATING Fuel Operating Range NOTE: Use “Ultra Low Sulfur Diesel (ULSD) Fuels” ONLY. Fuel Operating Range Chart *No. 1 ULSD Fuel should only be used where extended arctic conditions (0°F/-18°C) exist”.
Page 198
STARTING AND OPERATING NOTE: fueled in a warmer climate and driven to a RPM. The use of 120 Volts AC powered battery colder climate. The noise can typically be blankets will greatly increase starting capability at Use of Climatized ULSD or Number 1 ULSD ...
STARTING AND OPERATING NOTE: Engine Idling Your truck may have been ordered with an If ambient temperatures are low and the optional voltage monitoring idle up feature. If a Avoid prolonged idling, long periods of idling coolant temperature is below 180°F (82°C), load is placed on the electrical system while the may be harmful to your engine because truck is in park, this feature will attempt to...
STARTING AND OPERATING Idle-Up Feature Noise shut off. This is normal as the DEF dosing module is purging DEF. Fuel pump noise may The driver-controlled high idle speed feature will Diesel engines can create noises that may increase during low speed/light load conditions help increase cylinder temperatures and seem as a concern.
STARTING AND OPERATING Idle Time (min.) Before Engine Driving Condition Load Turbocharger Temperature Shutdown Stop and Go Empty Cool Less than One Stop and Go Medium Highway Speeds Medium Warm City Traffic Maximum GCWR Three Highway Speeds Maximum GCWR Four Uphill Grade Maximum GCWR Five...
STARTING AND OPERATING Operating Precautions Cooling System Tips CAUTION! To reduce potential for engine and transmission Avoid Overheating The Engine If oil pressure falls to less than normal overheating in high ambient temperature condi- The temperature of the engine coolant (anti- readings, shut the engine off immediately.
STARTING AND OPERATING Diesel Particulate Filter (DPF) Manual It includes a removable cap that is secured by a NOTE: tethered strap. It also has a c-clip that is used The engine block heater cord is a factory Regeneration - If Equipped for storage when not in use for the Winter installed option.
STARTING AND OPERATING ENGINE BREAK-IN RECOMMENDATIONS — Use the appropriate transmission gear to CAUTION! prevent engine lugging. GAS ENGINE Never use Non-Detergent Oil or Straight Observe vehicle oil pressure and tempera- Mineral Oil in the engine or damage may A long break-in period is not required for the ture indicators.
STARTING AND OPERATING DIESEL EXHAUST BRAKE (ENGINE WARNING! BRAKING) Do not use the exhaust brake feature when driving in icy or slippery conditions as the The purpose of the exhaust brake (engine increased engine braking can cause the rear braking) feature is to supply negative (braking) wheels to slide and the vehicle to swing torque from the engine.
STARTING AND OPERATING Automatic “Smart” Exhaust Brake The foot operated parking brake is located This light only shows that the parking brake is applied. It does not show the degree of brake below the lower left corner of the instrument Automatic “Smart”...
STARTING AND OPERATING AUTOMATIC TRANSMISSION WARNING! (Continued) WARNING! (Continued) Do not leave the key fob in or near the Unintended movement of a vehicle could WARNING! vehicle, or in a location accessible to chil- injure those in or near the vehicle. As with It is dangerous to shift out of PARK or ...
STARTING AND OPERATING NOTE: CAUTION! WARNING! (Continued) The transmission is NOT locked in PARK when Shift into or out of PARK or REVERSE only the ignition is in the ACC mode (even though the Your vehicle could move and injure you and ...
STARTING AND OPERATING Six–Speed Automatic Transmission — If Only shift from DRIVE to PARK or REVERSE NOTE: when the accelerator pedal is released and the After selecting any gear range, wait a moment Equipped vehicle is stopped. Be sure to keep your foot on to allow the selected gear to engage before Chassis Cab models (with automatic transmis- the brake pedal when shifting between these...
Page 210
STARTING AND OPERATING NOTE: WARNING! (Continued) WARNING! (Continued) On four-wheel drive vehicles be sure that the transfer case is in a drive position. It is dangerous to shift out of PARK or Never leave children alone in a vehicle, or ...
Page 211
STARTING AND OPERATING NEUTRAL (N) DRIVE (D) CAUTION! (Continued) Use this range when the vehicle is standing for This range should be used for most city and DO NOT race the engine when shifting from prolonged periods with the engine running. The highway driving.
Page 212
STARTING AND OPERATING If the transmission temperature exceeds During cold temperatures, transmission opera- enters Limp Home Mode at highway speeds, it normal operating limits, the powertrain tion may be modified depending on engine and will initially engage fifth gear, until the vehicle controller will modify the transmission shift transmission temperature as well as vehicle slows to a speed where third gear can be...
Page 213
STARTING AND OPERATING NOTE: You can switch between DRIVE and ERS mode To exit ERS mode, simply push and hold the ERS Even if the transmission can be reset, we at any vehicle speed. When the gear selector is (+) switch until the gear limit display disappears recommend that you visit your authorized in the DRIVE position, the transmission will from the instrument cluster.
Page 214
STARTING AND OPERATING Overdrive Operation feeling or response during normal operation in When To Use TOW/HAUL Mode the upper gears. When the vehicle speed drops The automatic transmission includes an elec- When driving in hilly areas, towing a trailer, or during some accelerations, the clutch auto- tronically controlled Overdrive (FIFTH and SIXTH carrying a heavy load, etc., and frequent trans- matically disengages.
STARTING AND OPERATING The “TOW/HAUL Indicator Light” will illuminate transmission out of PARK (or NEUTRAL, when the brake pedal when shifting between these in the instrument cluster to indicate that TOW/ the vehicle is stopped or moving at low speeds). gears.
Page 216
STARTING AND OPERATING Gear Ranges NOTE: WARNING! (Continued) On four-wheel drive vehicles be sure that the Do not depress the accelerator pedal when transfer case is in a drive position. The transmission may not engage PARK if shifting from PARK or NEUTRAL into another the vehicle is moving.
Page 217
STARTING AND OPERATING The following indicators should be used to WARNING! (Continued) WARNING! (Continued) ensure that you have properly engaged the transmission into the PARK position: Unintended movement of a vehicle could Do not leave the key fob in or near the ...
Page 218
STARTING AND OPERATING NEUTRAL (N) DRIVE (D) Transmission Limp Home Mode Use this range when the vehicle is standing for This range should be used for most city and Transmission function is monitored electroni- prolonged periods with the engine running. highway driving.
Page 219
STARTING AND OPERATING 1. Stop the vehicle. Electronic Range Select (ERS) Operation The Electronic Range Select (ERS) shift control 2. Shift the transmission into PARK, if allows the driver to limit the highest available possible. If not, shift the transmission to gear when the transmission is in DRIVE.
STARTING AND OPERATING When to Use TOW/HAUL Mode You have the ability to configure the function- WARNING! ality of the auxiliary switches via the instrument When driving in hilly areas, towing a trailer, Do not use the “TOW/HAUL” feature when cluster display.
STARTING AND OPERATING Electronically Shifted Transfer Case (Eight For additional information on the appropriate N (Neutral) use of each transfer case mode position, see Speed Transmission) — If Equipped N (Neutral) — This range disengages both the the information below: front and rear driveshafts from the powertrain.
Page 222
STARTING AND OPERATING This electronically shifted transfer case is NOTE: If One Or More Of The Following Shift Conditions designed to be driven in the two–wheel drive The transfer case Neutral button is located in Are Not Met: position (2WD) for normal street and highway the center of the 4WD Control Switch and is 1.
Page 223
STARTING AND OPERATING Shifting Procedure 2WD To 4WD HIGH WARNING! Push the desired position on the 4WD control NOTE: Always engage the parking brake when switch to shift the transfercase. Shifts between powering down the vehicle if the “SVC 4WD If any of the requirements to select a new 2WD and 4WD HIGH can be done with the ...
STARTING AND OPERATING 2WD Or 4WD HIGH To 4WD LOW Alternate Procedure Electronically Shifted Transfer Case (Six Speed Transmisson) — If Equipped NOTE: 1. Bring the vehicle to a complete stop. The electronic shift transfer case is operated by When shifting into or out of 4WD LOW some 2.
Page 225
STARTING AND OPERATING For additional information on the appropriate N (Neutral) wheels to rotate at the same speed. This is use of each transfer case mode position, see accomplished by rotating the 4WD Control N (Neutral) — This range disengages both the the information below: Switch to the desired position.
Page 226
STARTING AND OPERATING If All Of The Following Shift Conditions Are Met: selection. To find the shift requirements, refer Proper operation of four-wheel drive vehicles to the "Shifting Procedure" for your transfer depends on tires of equal size, type and circum- 1.
Page 227
STARTING AND OPERATING If all the requirements to select a new will flash and the original position indicator light Alternate Procedure transfer case position have been met, the will remain on. At this time, reduce speed and 1. Bring the vehicle to a complete stop. current position indicator light will turn OFF, stop spinning the wheels to complete the shift.
STARTING AND OPERATING Manually Shifted Transfer Case — If N (Neutral) The 4H and 4L positions are intended for loose, Equipped slippery road surfaces only. Driving in the 4H N (Neutral) — This range disengages both the and 4L positions on dry, hard surfaced roads front and rear driveshafts from the powertrain.
Page 229
STARTING AND OPERATING Because four-wheel drive provides improved Four-Wheel Drive High Range (4H) Shifting Procedure — Manually Shifted traction, there is a tendency to exceed safe Transfer Case Four-Wheel Drive High Range — This range locks turning and stopping speeds. Do not go faster the front and rear driveshafts together forcing 2H To 4H than road conditions permit.
STARTING AND OPERATING LIMITED-SLIP DIFFERENTIAL NOTE: Care should be taken to avoid sudden accelera- tions when both rear wheels are on a slippery Pausing in transfer case Neutral in vehicles The limited-slip differential provides additional surface. This could cause both rear wheels to equipped with an automatic transmission traction on snow, ice, mud, sand and gravel, spin, and allow the vehicle to slide sideways on...
STARTING AND OPERATING POWER STEERING Upon initial start-up in cold weather, the WARNING! power steering pump may make noise for a Hydraulic Power Steering short amount of time. This is due to the cold, Fluid level should be checked on a level thick fluid in the steering system.
STARTING AND OPERATING SPEED CONTROL at the same time. If this occurs, the Speed NOTE: Control system can be reactivated by pushing The vehicle should be traveling at a steady When engaged, the Speed Control takes over the Speed Control on/off button and resetting speed and on level ground before pushing the accelerator operations at speeds greater than the desired vehicle set speed.
STARTING AND OPERATING Metric Speed (km/h) If the button is continually pushed, the set On steep hills, a greater speed loss or gain may speed will continue to decrease until the occur so it may be preferable to drive without Pushing the RES (+) button once will result in ...
STARTING AND OPERATING ADAPTIVE CRUISE CONTROL (ACC) — IF The Cruise Control system has two control WARNING! modes: EQUIPPED Adaptive Cruise Control (ACC) is a conve- Adaptive Cruise Control mode for main- nience system. It is not a substitute for taining an appropriate distance between Adaptive Cruise Control (ACC) increases the active driving involvement.
STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) Does not always fully recognize You should switch off the ACC system: complex driving conditions, which can When driving in fog, heavy rain, heavy result in wrong or missing distance snow, sleet, heavy traffic, and complex warnings.
STARTING AND OPERATING Activating Adaptive Cruise Control (ACC) When the driver door is open at low speed. To turn the system off, push and release the Adaptive Cruise Control (ACC) on/off button You can only engage ACC if the vehicle speed is When the driver seat belt is unbuckled at low ...
STARTING AND OPERATING To Set A Desired ACC Speed The system will not be controlling the A Trailer Sway Control (TSC) event occurs. distance between your vehicle and the When the vehicle reaches the speed desired, The driver switches ESC to Full Off mode. ...
STARTING AND OPERATING To Resume To Vary The Speed Setting If the button is continually pushed, the set speed will continue to increase in 10 km/h If there is a set speed in memory push the RES To Increase Speed increments until the button is released.
STARTING AND OPERATING Metric Speed (km/h) either have to push the RES (+) button, or apply the accelerator pedal to reengage the Pushing the SET (-) button once will result in ACC to the existing set speed. a 1 km/h decrease in set speed. Each subse- quent tap of the button results in a decrease The ACC system maintains set speed when ...
Page 240
STARTING AND OPERATING shortest setting is reached, if the button is NOTE: pushed again it will reset to the default setting The brake lights will illuminate whenever the (longest). ACC system applies the brakes. If there is no vehicle ahead, the vehicle will A Proximity Warning will alert the driver if ACC maintain the set speed.
STARTING AND OPERATING Trailer Detect — If Equipped If the target vehicle does not start moving within Adaptive Cruise Control (ACC) Menu two seconds of your vehicle coming to a stand- When a trailer is detected, the ACC system auto- The instrument cluster display will show the still, then ACC will cancel and the driver must matically defaults to the longest setting (four...
STARTING AND OPERATING Adaptive Cruise Control Set This most often occurs at times of poor visibility, To keep the ACC System operating properly, it is such as in snow or heavy rain. The ACC system important to note the following maintenance When the RES (+) or the SET(-) button (located may also become temporarily blinded due to items:...
STARTING AND OPERATING Installing a snow plow, front-end protector, If weather conditions are not a factor, the driver Precautions While Driving With ACC an aftermarket grille or modifying the grille is should examine the windshield and the camera In certain driving situations, ACC may have not recommended.
Page 244
STARTING AND OPERATING Towing A Trailer Turns And Bends Using ACC On Hills ACC while towing a trailer is recommended only When driving on a curve with ACC engaged, the When driving on hills, ACC may not detect a with an Integrated Trailer Brake Controller. system may decrease the vehicle speed and vehicle in your lane.
Page 245
STARTING AND OPERATING Lane Changing Narrow Vehicles Stationary Objects And Vehicles ACC may not detect a vehicle until it is Some narrow vehicles traveling near the outer ACC does not react to stationary objects and completely in the lane in which you are trav- edges of the lane or edging into the lane are not stationary vehicles.
STARTING AND OPERATING General Information La operación de este equipo está sujeta a las Normal (Fixed Speed) Cruise Control on/off siguientes dos condiciones: button will result in turning on (changing to) the The following regulatory statement applies to all Normal (Fixed Speed) Cruise Control mode. Radio Frequency (RF) devices equipped in this 1.
Page 247
STARTING AND OPERATING To Vary The Speed Setting Metric Speed (km/h) U.S. Speed (mph) Pushing the RES (+) button once will result in Pushing the SET (-) button once will result in To Increase Speed a 1 km/h increase in set speed. Each subse- a 1 mph decrease in set speed.
STARTING AND OPERATING To Cancel The ignition is placed in the OFF position. will appear within the instrument cluster display indicating the vehicle speed is too fast. The The following conditions will cancel the Normal You engage Four-Wheel Drive Low. ...
STARTING AND OPERATING ParkSense Warning Display The ParkSense Warning screen is located within the instrument cluster display. It provides visual warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Refer to “Instrument Cluster Display” in “Getting To Know Your Instrument Panel” for further information.
Page 250
STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. The following chart shows the warning alert operation when the system is detecting an obstacle: Fast Tone Continuous Tone WARNING ALERTS Greater than...
STARTING AND OPERATING Adjustable Chime Volume Settings The ParkSense switch LED will be on when Park- If "Rear ParkSense Unavailable Wipe Sensors" Sense is disabled or defective. The ParkSense appears in the instrument cluster display make The rear chime volume settings are program- switch LED will be off when the system is sure the outer surface and the underside of the mable through the Uconnect system.
STARTING AND OPERATING When you move the gear selector into WARNING! CAUTION! REVERSE with ParkSense turned off, the instrument cluster display will show "Off" on Drivers must be careful when backing up ParkSense is only a parking aid and it is ...
STARTING AND OPERATING ParkSense will retain the last system state The sensors can detect obstacles from approxi- ParkSense Display (enabled or disabled) from the last ignition cycle mately 18 inches (45 cm) up to 79 inches The warning display will turn on indicating the when the ignition is changed to the ON/RUN (200 cm) from the rear fascia/bumper in the system status when the vehicle is in REVERSE...
Page 254
STARTING AND OPERATING Slow Tone Fast Tone For Rear Only Continuous Tone If an obstacle is detected in one or more of the rear regions (left/center/right), the display will show a single arc in the left, center, or rear region and the system will produce a tone. As the vehicle moves closer to the obstacle, the display will show the single arc moving closer to the vehicle and the tone will change from a...
Page 255
STARTING AND OPERATING WARNING ALERTS FOR REAR Greater than Less than Rear Distance 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches 79 inches 12 inches (inches/cm) (200-150 cm) (150-120 cm) (120-100 cm) (100-65 cm) (65-30 cm) (200 cm) (30 cm) Audible Alert Single 1/2...
STARTING AND OPERATING Front Park Assist Audible Alerts vehicle graphic will be displayed for as long as If "Front/Rear ParkSense Unavailable Wipe the vehicle is in REVERSE. Sensors" appears in the instrument cluster ParkSense will turn off the Front Park Assist display make sure the outer surface and the audible alert (chime) after approximately three The Front or Rear ParkSense switch LED will be...
Page 257
STARTING AND OPERATING When you move the gear selector to the WARNING! CAUTION! REVERSE position and Front or Rear Park- Sense is turned off, the instrument cluster Drivers must be careful when backing up ParkSense is only a parking aid and it is ...
STARTING AND OPERATING LANESENSE — IF EQUIPPED When only a single lane marking is detected To turn the LaneSense system on, push the and the driver unintentionally drifts across that LaneSense button (LED turns off). A “Lane- LaneSense Operation lane marking (no turn signal applied), the Lane- Sense On”...
STARTING AND OPERATING Left Lane Departure — Only Left Lane Detected LaneSense Warning Message NOTE: The LaneSense system operates with similar When the LaneSense system is on, the Lane- The LaneSense system will indicate the current behavior for a right lane departure when only Sense Telltale is solid white when only the lane drift condition through the instrument...
STARTING AND OPERATING When the LaneSense system senses a lane For example: If approaching the left side of NOTE: drift situation, the left lane line turns solid the lane the steering wheel will turn to the When enabled the system operates above ...
Page 261
STARTING AND OPERATING NOTE: Whenever the Rear View Camera image is acti- If equipped with a Cargo Camera, a touchscreen For the 3500, 4500, and 5500 Chassis Cab vated through the "Backup Camera" button in button to indicate the current active Camera vehicles, the Rear Backup Camera is shipped the "Controls"...
Page 262
STARTING AND OPERATING A dashed center line overlay indicates the will return the view to the standard Backup CAUTION! center of the vehicle to assist with parking or Camera display. aligning to a hitch/receiver. The following table To avoid vehicle damage, ParkView should ...
STARTING AND OPERATING SURROUND VIEW CAMERA SYSTEM — IF AUX Camera — If Equipped Deactivation The AUX Camera is deactivated by pressing the Your vehicle may be equipped with one or two EQUIPPED “X” in the upper right corner of the touchscreen. AUX Cameras, which display a rearview image This will return the display back to the previ- Your vehicle may be equipped with the...
Page 264
STARTING AND OPERATING NOTE: Modes Of Operation Standard Backup Camera view can be manually For the 3500, 4500, and 5500 Chassis Cab activated by selecting “Backup Camera” vehicles, the Rear Backup Camera is shipped through the Controls menu within the Uconnect loose and not installed.
Page 265
STARTING AND OPERATING Rear Cross Path View NOTE: Pressing the Left & Right Tow Mirror If the Backup Camera view was selected Split Screen View button within the Pressing the Rear Cross Path soft through the Surround View screen, exiting out of Trailer Reverse Guidance screen will key will give the driver a wider display a split screen to allow the...
Page 266
STARTING AND OPERATING When Zoom View is selected while the vehicle is Deactivation The system is deactivated in the following in REVERSE, then shifted to DRIVE, the camera conditions if it was activated manually from the The system is deactivated in the following delay view will display the standard Backup Uconnect controls menu via the Surround View conditions if it was activated automatically:...
Page 267
STARTING AND OPERATING NOTE: Shifting to NEUTRAL from any gear will maintain Activation the selected view (Zoom or Standard) as long as The Forward Facing Camera can be activated by If snow, ice, mud, or any foreign substance the vehicle is below 8 mph (13 km/h). pressing the Forward Camera soft button on the builds up on the camera lenses, clean the Zoom View is available until the gear selector is...
Page 268
STARTING AND OPERATING Trailer Reverse Guidance — If Equipped If Trailer Reverse Guidance is selected through CAUTION! manually activated Surround View, Backup The Trailer Reverse Guidance feature assists Camera, or Cargo Camera, the below deactiva- To avoid vehicle damage, Surround View ...
STARTING AND OPERATING ENGINE RUNAWAY AUX Camera — If Equipped Deactivation The AUX Camera is deactivated by pressing the Your vehicle may be equipped with one or two Diesel engine runaway is a rare condition “X” in the upper right corner of the touchscreen. AUX Cameras, which display a rearview image affecting diesel engines, where the engine This will return the display back to the previ-...
STARTING AND OPERATING REFUELING THE VEHICLE — GAS ENGINE NOTE: WARNING! When the fuel nozzle “clicks” or shuts off the fuel tank is full. A fire may result if gasoline is pumped into a CAUTION! portable container that is inside of a vehicle. Damage to the fuel system or emissions ...
STARTING AND OPERATING REFUELING THE VEHICLE — DIESEL ENGINE Fuel Filler Cap Bulk Fuel Storage — Diesel Fuel If the fuel filler cap is lost or damaged, be sure If you store quantities of fuel, good mainte- CAUTION! the replacement cap is for use with this vehicle. nance of the stored fuel is also essential.
STARTING AND OPERATING Diesel Exhaust Fluid The DEF injection system consists of the Diesel Exhaust Fluid Storage following components: Your vehicle is equipped with a Selective Cata- Diesel Exhaust Fluid (DEF) is considered a very DEF tank lytic Reduction (SCR) system to meet the very stable product with a long shelf life.
STARTING AND OPERATING Adding Diesel Exhaust Fluid (DEF) DEF Fill Procedure NOTE: The DEF gauge (located on the instrument NOTE: The DEF gauge may take up to five seconds cluster) will display the level of DEF remaining in to update after adding a gallon or more of Refer to “Fluids And Lubricants”...
Page 274
STARTING AND OPERATING Filling The Def Tank In Cold Climates CAUTION! CAUTION! (Continued) Since DEF will begin to freeze at 12°F (-11°C), To avoid DEF spillage, and possible Never add anything other than DEF to the your vehicle is equipped with an automatic DEF damage to the DEF tank from overfilling, do tank –...
STARTING AND OPERATING VEHICLE LOADING times specified by purchasers for increased Loading durability does not necessarily increase the The actual total weight and the weight of the Gross Vehicle Weight Rating (GVWR) vehicle's GVWR. front and rear of your vehicle at the ground can The GVWR is the total permissible weight of your Tire Size best be determined by weighing it when it is...
STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) Gross Combination Weight Rating (GCWR) CAUTION! The GVWR is the total allowable weight of your The GCWR is the total allowable weight of your Do not load your vehicle any heavier than the vehicle.
Page 277
STARTING AND OPERATING Trailer Frontal Area Weight-Distributing Hitch WARNING! The frontal area is the maximum height multi- A weight-distributing system works by applying An improperly adjusted weight distributing plied by the maximum width of the front of a leverage through spring (load) bars. They are hitch system may reduce handling, stability trailer.
Page 278
STARTING AND OPERATING Recommended Distribution Hitch Adjustment 3. Attach the trailer to the vehicle without the weight distribution bars connected. 1. Position the truck to be ready to connect to the trailer (do not connect the trailer). 4. Measure the height of the top of the front wheel opening on the fender to ground, this 2.
Page 279
STARTING AND OPERATING 6. Perform a visual inspection of the trailer Fifth-Wheel Hitch Gooseneck Hitch and weight distributing hitch to confirm The fifth-wheel hitch is a special high platform The gooseneck hitch employs a pivoted manufacturers’ recommendations have with a coupling that mounts over the rear axle of coupling arm which attaches to a ball mounted been met.
STARTING AND OPERATING Trailer Hitch Type and Maximum Trailer Weight The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Towing Requirements CAUTION! Weight Ratings) To promote proper break-in of your new vehicle Always load a trailer with 60% of the weight in drivetrain components, the following guidelines NOTE: the front of the trailer. This places 10% of the are recommended.
Page 282
STARTING AND OPERATING Proper tire inflation pressures are essential WARNING! WARNING! (Continued) to the safe and satisfactory operation of your Make certain that the load is secured in the vehicle. Refer to “Tires” in “Servicing And Vehicles with trailers should not be parked ...
Page 283
STARTING AND OPERATING An electronically actuated trailer brake CAUTION! controller is required when towing a trailer with electronically actuated brakes. When If the trailer weighs more than 1,000 lbs towing a trailer equipped with a hydraulic (453 kg) loaded, it should have its own surge actuated brake system, an electronic brakes and they should be of adequate brake controller is not required.
Page 284
STARTING AND OPERATING The trailer and the vehicle’s stop lamps will change. Changes to towing conditions include 4. Push the UP or DOWN button on the come on when braking normally with the vehicle trailer load, vehicle load, road conditions and steering wheel until “TRAILER TOW”...
Page 285
STARTING AND OPERATING Light Electric Heavy Electric Light EOH Heavy EOH Electric over Hydraulic Electric over Hydraulic Type of Trailer Brakes Electric Trailer Brakes Electric Trailer Brakes Trailer Brakes Trailer Brakes *Under 10,000 lbs *Above 10,000 lbs *Under 10,000 lbs *Above 10,000 lbs Load (4,536 kg)
STARTING AND OPERATING Towing Requirements — Trailer Lights And Wiring Whenever you pull a trailer, regardless of the trailer size, stoplights and turn signals on the trailer are required for motoring safety. The Trailer Tow Package may include a four- and seven-pin wiring harness.
Page 287
STARTING AND OPERATING Automatic Transmission If you regularly tow a trailer for more than Speed Control — If Equipped 45 minutes of continuous operation, then The DRIVE range can be selected when towing. Do not use on hilly terrain or with heavy ...
STARTING AND OPERATING SNOWPLOW Snowplow Prep Package Model Availability CAUTION! For Information about snowplow applications Snowplow Prep Packages are available as a The “Lamp Out” indicator could illuminate if visit www.ramtrucks.com or refer to the current factory installed option. These packages exterior lamps are not properly installed.
STARTING AND OPERATING Vehicle front end wheel alignment was set to Operating Tips Vehicles with automatic transmissions specifications at the factory without consider- should use 4LO range when plowing deep or Under ideal snow plowing conditions, 20 mph heavy snow for extended periods of time to ation for the weight of the plow.
STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle Wheels OFF The Two-Wheel Drive Towing Condition Four-Wheel Drive Models Ground Models See Instructions Automatic transmission in PARK Flat Tow NONE NOT ALLOWED Transfer case in NEUTRAL (N) ...
STARTING AND OPERATING Recreational Towing — Two-Wheel Drive CAUTION! CAUTION! Models Towing with the rear wheels on the ground DO NOT dolly tow any 4WD vehicle. Towing DO NOT flat tow this vehicle. Damage to the will cause severe transmission damage. with only one set of wheels on the ground drivetrain will result.
Page 292
STARTING AND OPERATING blinking (stay on solid) when the shift to N CAUTION! CAUTION! (Continued) (Neutral) is complete. After the shift is It is necessary to follow these steps to be completed and the N (Neutral) light stays Do not disconnect the rear driveshaft ...
Page 293
STARTING AND OPERATING NOTE: Shifting Out Of N (Neutral) With electronic shift transfer case with With electronic shift transfer case: push-button selector switch, push and Use the following procedure to prepare your hold the switch for the desired transfer vehicle for normal usage: Steps 2 through 3 are requirements that ...
STARTING AND OPERATING 9. Press and hold the brake pedal. A flashing N (Neutral) position indicator light Driving Through Water indicates that shift requirements have not Driving through water more than a few inches/ 10. Release the parking brake. been met.
Page 295
STARTING AND OPERATING Shallow Standing Water CAUTION! CAUTION! (Continued) Although your vehicle is capable of driving Always check the depth of the standing Driving through standing water may cause through shallow standing water, consider the water before driving through it. Never drive damage to your vehicle’s drivetrain compo- following Cautions and Warnings before doing through standing water that is deeper than...
IN CASE OF EMERGENCY HAZARD WARNING FLASHERS ASSIST AND SOS SYSTEM — IF EQUIPPED This is an emergency warning system and it should not be used when the vehicle is in The Hazard Warning Flashers switch motion. Use it when your vehicle is disabled and NOTE: is located on the upper switch bank it is creating a safety hazard for other motorists.
Page 297
IN CASE OF EMERGENCY NOTE: SiriusXM Guardian™ Customer Care – In-vehicle support for SiriusXM Guardian™. Your vehicle may be transmitting data as authorized by the subscriber. Vehicle Customer Care – Total support for all other vehicle issues. The SOS and ASSIST buttons will only func- ...
Page 298
IN CASE OF EMERGENCY 3. Once a connection between the vehicle and NOTE: WARNING! a SOS operator is made, the SOS Call Your vehicle may be transmitting data as system may transmit the following If anyone in the vehicle could be in danger ...
Page 299
IN CASE OF EMERGENCY SOS Call System Limitations WARNING! (Continued) WARNING! Vehicles sold in Mexico DO NOT have SOS Call The SOS Call system is embedded into the Ignoring the overhead console light could system capabilities. vehicle’s electrical system. Do not add mean you will not have SOS Call services.
Page 300
IN CASE OF EMERGENCY These include, but are not limited to, the LTE (voice/data) or 4G (data) network NOTE: congestion. following factors: Your vehicle may be transmitting data as Delayed accessories mode is active. Weather. authorized by the subscriber. ...
IN CASE OF EMERGENCY General Information Le présent appareil est conforme aux CNR La operación de este equipo está sujeta a las d`Innovation, Science and Economic Develop- siguientes dos condiciones: The following regulatory statement applies to all ment applicables aux appareils radio exempts Radio Frequency (RF) devices equipped in this 1.
IN CASE OF EMERGENCY BULB REPLACEMENT Replacement Bulbs All of the inside bulbs are brass or glass-wedge base. Aluminum base bulbs are not approved. Interior Bulbs Bulb Name Bulb Number Overhead Console Lamps TS 212–9 Dome Lamp 7679 NOTE: For lighted switches, see an authorized dealer for replacement instructions. Exterior Bulbs Bulb Name Bulb Number...
IN CASE OF EMERGENCY Exterior Bulbs Bulb Name Bulb Number Front Fog Lamps (LED Headlamps) LED (Serviced At An Authorized Dealer) Side Indicators (Front And Side View Mirror) LED (Serviced At An Authorized Dealer) Center High Mounted Stop Lamp (CHMSL) Cab Roof Marker Lamps 194NA Box Off Tail Lamps –...
Page 304
IN CASE OF EMERGENCY 5. Disconnect the internal lamp wiring harness 3. Look under the hood and behind the head- Front Park And Turn connector from the low beam bulb. lamp to find the high beam bulb access 1. Open the hood. cover.
Page 305
IN CASE OF EMERGENCY Side Marker Lamp 4. Reach through the access hole of the wheel Fog Lamps — If Equipped house splash shield and disengage the side 1. Open the hood. 1. Reach under and behind the front bumper marker socket by rotating counterclockwise to access the back of the front fog lamp a quarter turn.
Page 306
IN CASE OF EMERGENCY Center High Mounted Stoplamp (CHMSL) 2. Separate the connector holding the housing With Cargo Lamp and wiring harness to the body. 1. Remove the two screws holding the housing/lens to the body as shown. CHMSL Bulb And Socket CAUTION! CHMSL Connector Location Do not contaminate the bulb glass by...
IN CASE OF EMERGENCY FUSES Cab Top Clearance Lamps — If Equipped 2. Rotate the bulb socket a quarter turn and pull it from the lamp assembly. 1. Remove the two screws from the top of the WARNING! lamp. When replacing a blown fuse, always use ...
IN CASE OF EMERGENCY Power Distribution Center WARNING! (Continued) The Power Distribution Center is located in the If a general protection fuse for safety engine compartment near the battery. This systems (air bag system, braking system), center contains cartridge fuses, micro fuses, power unit systems (engine system, trans- relays, and circuit breakers.
Page 309
IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 40 Amp Green (SSV & – Aux Relay Output / Diesel Fuel Heater – If Equipped Cummins Diesel) 30 Amp Pink – Brake Vacuum Pump – If Equipped (HD Only) 40 Amp Green –...
Page 310
IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description Engine Control Module GPEC / Heavy Duty / Other – If 20 Amp Blue – Equipped 25 Amp White (Cummins – PCM – If Equipped Diesel) 30 Amp Pink – CBC Feed # 1 30 Amp Pink –...
Page 311
IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 30 Amp Pink – Electric Back Light – If Equipped Fuel Heater #2, Aux Relay 2 – If Equipped (HD Only) 30 Amp Pink – SSV (DS 1500 Only) Integrated Trailer Brake Module – If Equipped (HD Only) 30 Amp Pink –...
Page 312
IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 15 Amp Blue Additional Diesel Content - If Equipped (DS 1500 Only) – 10 Amp Red Fuel Vapor Blocker Valve - If Equipped (HD Only) TCM/PCM / Solenoid Trans Pressure SW (RFE Trans Only) –...
Page 313
IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red AEB RACAM HTR – If Equipped (HD Only) – 15 Amp Blue SCR Module – If Equipped (HD Only) Fuel Pump Motor / K09 RLY Coil Feed (Cummins Diesel) – –...
Page 314
IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description Engine Control Module / Powertrain Control Module / – 10 Amp Red Electric Power Steering (DS 1500 Only) Engine Control Module / Powertrain Control Module / AEB – 15 Amp Blue RACM MOD / Feed To AUX PDC Relay Coils/ HRLS (HD Only) –...
Page 315
IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description IGN or BATT Customer Selectable – If Equipped (HD Only) F90/F91 – 20 Amp Yellow Power Outlet (Rear Seats) Customer Selectable (DS 1500 Only) – 20 Amp Yellow Cigar Lighter - If Equipped Shift-By-Wire / Transfer Case Switch (DS 1500 Only) –...
IN CASE OF EMERGENCY 4500/5500 Models 5. Turn the ignition OFF. Jacking Instructions 4500 And 5500 Series These vehicles do not come equipped with a 6. Block both the front and rear of the wheel WARNING! jack. diagonally opposite the jacking position. For Carefully follow these tire changing warnings example, if the driver’s front wheel is being NOTE:...
Page 318
IN CASE OF EMERGENCY 1. If equipped, remove the spare wheel, jack, (unless both tires are flat on one side, then WARNING! (Continued) and tools from storage. place jack under shock bracket) facing for- ward in vehicle. Connect the extension Only use the jack in the positions indicated ...
Page 319
IN CASE OF EMERGENCY Dual Rear Wheels WARNING! WARNING! Slots in the wheels will assist in properly Raising the vehicle higher than necessary can A loose tire or jack thrown forward in a orienting the inner and outer wheels. Align make the vehicle less stable.
IN CASE OF EMERGENCY It is recommended that wheel stud nuts be kept Refer to “Wheel And Tire Torque Specifications” For 3500 Single Rear-Wheel (SRW) models, use torqued to specifications at all times. Torque in “Technical Specifications” for further infor- the flat end of the lug wrench to hook and pull wheel stud nuts to specifications at each lubri- mation.
IN CASE OF EMERGENCY On 3500 models with Dual Rear-Wheels (DRW), WARNING! CAUTION! you must first remove the hub caps—use the procedure noted for the single rear wheel. For Do not attempt jump starting if the battery is Use a pulling motion to remove the hub ...
IN CASE OF EMERGENCY Preparations For Jump Start WARNING! WARNING! The battery in your vehicle is located in the front Do not allow vehicles to touch each other as Take care to avoid the radiator cooling fan of the engine compartment, behind the left whenever the hood is raised.
IN CASE OF EMERGENCY 2. Connect the opposite end of the positive (+) If frequent jump starting is required to start your CAUTION! jumper cable to the positive (+) post of the vehicle you should have the battery and booster battery. Do not connect jumper cable to any of the charging system inspected at an authorized dealer.
IN CASE OF EMERGENCY NOTE: 5. Insert a screwdriver or similar tool into the CAUTION! There are steps that you can take to slow down access port (ringed circle) on the bottom of an impending overheat condition: Driving with a hot cooling system could the steering column, and push and hold the damage your vehicle.
IN CASE OF EMERGENCY MANUAL PARK RELEASE — 8 – SPEED TRANSMISSION WARNING! Always secure your vehicle by fully applying the parking brake before activating the Manual Park Release. In addition, you should be seated in the driver’s seat with your foot Engaging The Access Port firmly on the brake pedal when activating the Manual Park Release Cover...
IN CASE OF EMERGENCY FREEING A STUCK VEHICLE Follow these steps to activate the Manual Park 6. The vehicle is now out of PARK and can be Release: towed. Release the parking brake only when If your vehicle becomes stuck in mud, sand, or the vehicle is securely connected to a tow 1.
Page 327
IN CASE OF EMERGENCY NOTE: WARNING! CAUTION! For trucks equipped with an 8–speed trans- Fast spinning tires can be dangerous. Forces Racing the engine or spinning the wheels mission, shifts between DRIVE and REVERSE generated by excessive wheel speeds may may lead to transmission overheating and can only be achieved at wheel speeds of cause damage, or even failure, of the axle...
IN CASE OF EMERGENCY TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. If the transmission and drivetrain are operable, disabled vehicles may also be towed as described under “Recreational Towing” in the “Starting And Operating” section. Towing Condition Wheels OFF The 2WD Models 4WD Models...
IN CASE OF EMERGENCY Two-Wheel Drive Models If the transmission is not operable, or the Four-Wheel Drive Models vehicle must be towed faster than 30 mph The manufacturer recommends towing your The manufacturer recommends towing with all (48 km/h) or farther than 15 miles (24 km) for vehicle with all four wheels OFF the ground wheels OFF the ground.
IN CASE OF EMERGENCY ENHANCED ACCIDENT RESPONSE SYSTEM Emergency Tow Hooks — If Equipped WARNING! Your vehicle may be equipped with emergency (EARS) Do not use a chain for freeing a stuck tow hooks. vehicle. Chains may break, causing serious This vehicle is equipped with an Enhanced Acci- injury or death.
SERVICING AND MAINTENANCE SCHEDULED SERVICING — GAS ENGINE An authorized dealer will reset the oil change Once A Month Or Before A Long Trip: indicator message after completing the sched- Check engine oil level. Your vehicle is equipped with an automatic oil uled oil change.
SERVICING AND MAINTENANCE Maintenance Plan At Every Oil Change Interval As Indicated At Every Oil Change Interval As Indicated Required Maintenance By Oil Change Indicator System: By Oil Change Indicator System: Refer to the maintenance plan on the following Change oil and filter. Inspect automatic transmission fluid if ...
Page 333
SERVICING AND MAINTENANCE Maintenance Plan — Gas Engine Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Inspections Inspect the CV/Universal joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle surfaces.
Page 334
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Additional Maintenance Replace engine air filter. Replace spark plugs. Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change the automatic transmission fluid (AS66RC Transmission Only).
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first) Or Years: Or Kilometers: Change the transfer case fluid. Inspect and replace PCV valve if necessary. 1. The spark plug change interval is mileage based only, yearly intervals do not apply. Heavy Duty Use Of The Vehicle WARNING! WARNING! (Continued)
SERVICING AND MAINTENANCE SCHEDULED SERVICING — DIESEL ENGINE At Each Stop For Fuel At Each Oil Change Check the engine oil level at least 30 minutes Change the engine oil filter. CAUTION! after a fully warmed engine is shut off. Checking Inspect the exhaust system.
SERVICING AND MAINTENANCE Oil Change Indicator System — Cummins Replace the engine oil and oil filter every 15, Perform Service Indicator — Cummins 000 miles (24,000 km) or 12 months, or Diesel Diesel sooner if prompted by the oil change indicator Your vehicle is equipped with an engine oil Your vehicle will require emissions mainte- system.
SERVICING AND MAINTENANCE Maintenance Plan — Cummins Diesel Engine Mileage or time passed (whichever comes first): Or Months: Or Kilometers: Change engine oil every 15,000 miles (24,000 km) or 12 months or 500 hours or sooner if prompted by the oil change indicator system, whichever comes first.
Page 339
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first): Or Months: Or Kilometers: Inspect engine air filter, replace if necessary. Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play;...
Page 340
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first): Or Months: Or Kilometers: Additional Maintenance Replace cabin air filter. Replace engine fuel filter element. Replace chassis mounted fuel filter element. Inspect the front and rear axle surfaces. If gear oil leakage is suspected, check the fluid level.
Page 341
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first): Or Months: Or Kilometers: Change the transfer case fluid (4x4). Change automatic transmission fluid (AS69RC transmission only). Change the automatic transmission fluid and sump filter (AS69RC transmission only). Change automatic transmission fluid and filter(s) if using your vehicle for any of the following: police, fleet, or frequent trailer...
Page 342
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first): Or Months: Or Kilometers: Change automatic transmission fluid and filter(s). Replace Crankcase Ventilation Filter (CCV).
Page 343
SERVICING AND MAINTENANCE Mileage or time passed (whichever comes first): Or Months: Or Kilometers: Flush and replace power steering fluid. Flush and replace engine coolant. *** 1. Under no circumstances should oil change intervals exceed 15,000 miles (24,000 km) or 12 months or 500 Hours, whichever comes first.
Page 344
SERVICING AND MAINTENANCE WARNING! WARNING! (Continued) CAUTION! You can be badly injured working on or Failure to properly inspect and maintain ***The manufacturer highly recommends around a motor vehicle. Do only service your vehicle could result in a component that all cooling system service, maintenance, work for which you have the knowledge and malfunction and effect vehicle handling...
SERVICING AND MAINTENANCE Checking Oil Level — Gas Engine parked overnight. When checking oil after oper- CAUTION! ating the engine, first ensure the engine is at full To ensure proper lubrication of your vehicle's operating temperature, then wait for Overfilling or underfilling the crankcase will engine, the engine oil must be maintained at 30 minutes after engine shutdown to check the cause oil aeration or loss of oil pressure.
SERVICING AND MAINTENANCE WARNING! WARNING! CAUTION! Commercially available windshield washer Battery fluid is a corrosive acid solution and It is essential when replacing the cables on can burn or even blind you. Do not allow the battery that the positive cable is solvents are flammable.
SERVICING AND MAINTENANCE DEALER SERVICE Engine Oil Engine Oil Selection — Diesel Engine For best performance and maximum protection Change Engine Oil — Gas Engine An authorized dealer has the qualified service under all types of operating conditions, the personnel, special tools, and equipment to The oil change indicator system will remind you manufacturer only recommends engine oils perform all service operations in an expert...
Page 350
SERVICING AND MAINTENANCE American Petroleum Institute (API) Engine Oil Engine Oil Viscosity — Gas Engine Shell Rimula that meets FCA Material Standard Identification Symbol — Diesel Engine MS-10902 and the API CK-4 engine oil category Use Mopar SAE 0W-40 engine oil approved to is required.
SERVICING AND MAINTENANCE Synthetic Engine Oils Engine Oil Filter WARNING! You may use synthetic engine oils provided the The engine oil filter should be replaced with a The air induction system (air cleaner, hoses, recommended oil quality requirements are met, new filter at every engine oil change.
Page 352
SERVICING AND MAINTENANCE Engine Air Cleaner Filter Removal Engine Air Cleaner Filter Inspection and Replacement — Diesel Engine 1. With suitable tool fully loosen (six) Inspect engine air cleaner filter for dirt and or fasteners on air cleaner filter. debris, if you find evidence of either dirt or debris you should change your air cleaner filter.
SERVICING AND MAINTENANCE 3. Remove the air cleaner filter element from 3. Install screws to secure the air cleaner CAUTION! the housing assembly. cover to the housing assembly. Do not use chemical flushes in your air Air Conditioner Maintenance conditioning system as the chemicals can damage your air conditioning components.
Page 354
SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling The cabin air filter is located in the fresh air inlet 3. There are travel stops on both sides of the R-1234yf — If Equipped behind the glove compartment. Perform the glove compartment. Push inward on right following procedure to replace the filter: side of the glove compartment travel stop to R-1234yf Air Conditioning Refrigerant is a...
Page 355
SERVICING AND MAINTENANCE 4. Remove the filter cover by pushing in on the 5. Remove the cabin air filter by pulling it 7. Reinstall the glove compartment on the finger tabs on each end of the filter cover. straight out of the housing. hinges.
SERVICING AND MAINTENANCE NOTE: When inspecting accessory drive belts, small Belt slips Ensure the glove compartment door hinges and cracks that run across ribbed surface of belt “Groove jumping" (belt does not maintain glove compartment travel stops are fully from rib to rib, are considered normal.
Page 357
SERVICING AND MAINTENANCE Upon proper draining of the water from both the ON position, and allow any accumulated CAUTION! fuel filters, the “Water In Fuel Indicator Light” water to drain. Leave the drain valve open until Do not drain the fuel/water separator filter will remain illuminated for approximately 10 all water and contaminants have been ...
SERVICING AND MAINTENANCE Engine Mounted Fuel Filter Replacement 7. Wipe clean the sealing surfaces of the lid CAUTION! and housing. NOTE: Diesel fuel will damage blacktop paving 8. Install new o-ring back into ring groove on surfaces. Drain the filter into an appro- Using a fuel filter that does not meet the ...
SERVICING AND MAINTENANCE Underbody Mounted Fuel Filter 5. Remove lid using a socket or strap wrench. CAUTION! Rotate counterclockwise for removal. Replacement Diesel fuel will damage blacktop paving Remove used o-ring and discard it. NOTE: surfaces. Drain the filter into an appro- 6.
SERVICING AND MAINTENANCE Priming If The Engine Has Run Out Of Fuel NOTE: CAUTION! A maximum blend of 5% biodiesel, meeting WARNING! Do not engage the starter motor for more ASTM specification D-975 may be used with than 15 seconds at a time. Allow two minutes Do not open the high pressure fuel system your Cummins diesel engine.
SERVICING AND MAINTENANCE Intervention Regeneration Strategy — will return to normal when the brake pedal is Diesel Exhaust Fluid applied. A small change in engine tone or a Message Process Flow Diesel Exhaust Fluid (DEF) sometimes known slight change in engine performance while simply by the name of its active component, The Cummins diesel engine meets all Environ- accelerating may also be noticeable at speeds...
SERVICING AND MAINTENANCE Body Lubrication Windshield Wiper Blades The wiper blades and wiper arms should be inspected periodically, not just when wiper Locks and all body pivot points, including such Clean the rubber edges of the wiper blades and performance problems are experienced. This items as seat tracks, door hinge pivot points the windshield periodically with a sponge or soft inspection should include the following points:...
Page 363
SERVICING AND MAINTENANCE Wiper Blade Removal/Installation 3. Tilt the lower end of the wiper blade away 5. With the wiper blade disengaged, remove from the arm and use one finger push the the wiper blade from the wiper arm by CAUTION! release tab toward the wiper arm.
SERVICING AND MAINTENANCE Installing The Front Wipers exhaust system and adjacent body areas for CAUTION! broken, damaged, deteriorated, or misposi- 1. Lift the wiper arm off of the glass, until the tioned parts. Open seams or loose connections The catalytic converter requires the use of ...
SERVICING AND MAINTENANCE NOTE: Cooling System Engine Coolant Checks Intentional tampering with emissions control Check the engine coolant (antifreeze) protec- WARNING! systems can result in civil penalties being tion every 12 months (before the onset of assessed against you. freezing weather, where applicable). If the You or others can be badly burned by hot ...
Page 366
SERVICING AND MAINTENANCE Cooling System — Drain, Flush And Refill NOTE: Some vehicles require special tools to add coolant properly. Failure to fill these systems Mixing of engine coolant (antifreeze) other NOTE: properly could lead to severe internal engine than specified Organic Additive Technology Some vehicles require special tools to add damage.
Page 367
SERVICING AND MAINTENANCE Mix a minimum solution of 50% OAT engine Mixing engine coolant (antifreeze) types is WARNING! (Continued) coolant that meets the requirements of FCA not recommended and can result in cooling Material Standard MS.90032 and distilled system damage.
SERVICING AND MAINTENANCE Checking Coolant Level — 6.4L Engine If an examination of your engine compartment Do not change the thermostat for Summer or Winter operation. If replacement is ever shows no evidence of radiator or hose leaks, The level of the coolant in the pressurized the vehicle may be safely driven.
SERVICING AND MAINTENANCE Brake System With disc brakes the fluid level can be expected WARNING! (Continued) to fall as the brake linings wear. However, an In order to ensure brake system performance, unexpected drop in fluid level may be caused by To avoid contamination from foreign matter ...
SERVICING AND MAINTENANCE Automatic Transmission Special Additives dipstick. An authorized dealer can check your transmission fluid level using special service The manufacturer strongly recommends Selection Of Lubricant tools. against using any special additives in the trans- It is important to use the proper transmission If you notice fluid leakage or transmission mission.
Page 371
SERVICING AND MAINTENANCE Use the following procedure to check the trans- 7. Remove the dipstick again and note the change. Re-check the fluid level, and adjust as mission fluid level properly: fluid level on both sides. The fluid level required, once the transmission reaches reading is only valid if there is a solid normal operating temperature.
SERVICING AND MAINTENANCE Rear Axle And 4x4 Front Driving Axle Fluid Drain And Refill CAUTION! Level On 4500/5500 vehicles, remove the lower bolt If the fluid temperature is below 50°F (10°C) to drain the axle fluid. For models with 9.25 in Front Axles and 11.5 in it may not register on the dipstick.
SERVICING AND MAINTENANCE Lubricant Selection Fluid Level Check Refer to “Fluids And Lubricants” in “Technical This fluid level can be checked by removing the Specifications” for further information. filler plug. The fluid level should be to the bottom edge of the filler plug hole with the NOTE: vehicle in a level position.
Page 374
SERVICING AND MAINTENANCE Exhaust System Tampering With Noise Control System ENGINE COOLING SYSTEM Prohibited Inspect the entire exhaust system for leaks and Removal or rendering inoperative the fan clutch. damaged parts. Devices such as hangers, Federal law prohibits the following acts or the clamps, and U-bolts should be tight and in good causing thereof: (1) the removal or rendering Removal of the fan shroud.
Page 375
SERVICING AND MAINTENANCE Maintenance Log and Service Chart (Diesel Engines) (Sheet 1 of 2) Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to the mileage at which service was performed. MILES 7,500 15,000 22,500 30,000...
SERVICING AND MAINTENANCE Maintenance Log and Service Chart (Diesel Engines) (Continued) (Sheet 2 of 2) Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to the mileage at which service was performed. MILES 67,500 75,000 82,500...
Page 377
SERVICING AND MAINTENANCE Tire Markings NOTE: LT (Light Truck) — Metric tire sizing is based on US design standards. The size designation P (Passenger) — Metric tire sizing is based on for LT-Metric tires is the same as for P-Metric US design standards.
Page 378
SERVICING AND MAINTENANCE Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on US design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on US design standards, or T or S = Temporary spare tire or 31 = Overall diameter in inches (in)
Page 379
SERVICING AND MAINTENANCE EXAMPLE: Load Identification: Absence of the following load identification symbols on the sidewall of the tire indicates a Standard Load (SL) tire: XL = Extra load (or reinforced) tire, or LL = Light load tire or ...
Page 380
SERVICING AND MAINTENANCE EXAMPLE: 01 = Number representing the year in which the tire was manufactured (two digits) 01 means the year 2001 Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured. Example: ...
Page 381
SERVICING AND MAINTENANCE Tire Loading And Tire Pressure This placard tells you important information about the: NOTE: 1. Number of people that can be carried in The proper cold tire inflation pressure is listed the vehicle. on the driver’s side B-Pillar or the rear edge of the driver's side door.
Page 382
SERVICING AND MAINTENANCE For further information on GAWRs, vehicle (4) The resulting figure equals the avail- Metric Example For Load Limit loading, and trailer towing, refer to “Vehicle able amount of cargo and luggage load For example, if “XXX” amount equals 635 kg Loading”...
SERVICING AND MAINTENANCE Safety Both underinflation and overinflation affect the WARNING! stability of the vehicle and can produce a feeling WARNING! of sluggish response or over responsiveness in Overloading of your tires is dangerous. the steering. Overloading can cause tire failure, affect Improperly inflated tires are dangerous and ...
Page 385
SERVICING AND MAINTENANCE Tire Inflation Pressures after sitting for a minimum of three hours. The Tire Pressures For High Speed Operation cold tire inflation pressure must not exceed the The proper cold tire inflation pressure is listed The manufacturer advocates driving at safe maximum inflation pressure molded into the on the driver's side B-Pillar or rear edge of the speeds and within posted speed limits.
Page 386
SERVICING AND MAINTENANCE Radial Ply Tires Damaged Run Flat tires, or Run Flat tires that NOTE: have experienced a loss of pressure should be TPM Sensor must be replaced after driving the WARNING! replaced immediately with another Run Flat tire vehicle on a flat tire condition.
Page 387
SERVICING AND MAINTENANCE Tread Wear Indicators Life Of Tire NOTE: Wheel valve stem must be replaced as well Tread wear indicators are in the original equip- The service life of a tire is dependent upon when installing new tires due to wear and tear ment tires to help you in determining when your varying factors including, but not limited to: in existing tires.
SERVICING AND MAINTENANCE It is recommended to replace the two front tires sidewall. Use all season tires only in sets of four; WARNING! (Continued) or two rear tires as a pair. Replacing just one tire failure to do so may adversely affect the safety can seriously affect your vehicle’s handling.
SERVICING AND MAINTENANCE Snow Tires Spare Tires — If Equipped Compact Spare Tire — If Equipped Some areas of the country require the use of The compact spare is for temporary emergency CAUTION! snow tires during the Winter. Snow tires can be use only.
Page 390
SERVICING AND MAINTENANCE Inflate collapsible tire only after the wheel is Full Size Spare — If Equipped WARNING! properly installed to the vehicle. Inflate the The full size spare is for temporary emergency Compact and collapsible spares are for collapsible tire using the electric air pump use only.
SERVICING AND MAINTENANCE Your wheels are susceptible to deterioration When cleaning extremely dirty wheels including WARNING! caused by salt, sodium chloride, magnesium excessive brake dust, care must be taken in the Limited use spares are for emergency use chloride, calcium chloride, etc., and other road selection of tire and wheel cleaning chemicals chemicals used to melt ice or control dust on and equipment to prevent damage to the...
SERVICING AND MAINTENANCE Dark Vapor Chrome, Black Satin Chrome, or Chassis Cab 3500 (Single Rear Wheel) Models CAUTION! Low Gloss Clear Coat Wheels Install on rear tires only. To avoid damage to your vehicle or tires, CAUTION! For LT275/70R18E tire, use of a U-class ...
SERVICING AND MAINTENANCE Refer to the “Maintenance Plan” for the proper Dual Rear Wheels CAUTION! (Continued) maintenance intervals. More frequent rotation is permissible if desired. The reasons for any Observe the traction device manufacturer’s rapid or unusual wear should be corrected prior instructions on the method of installation, operating speed, and conditions for use.
SERVICING AND MAINTENANCE After a tire rotation is completed, as shown Treadwear CAUTION! (Continued) below, the system can auto learn the loca- The Treadwear grade is a comparative tions of each sensor ID. Auto learning/local- When replacing a flat, the spare tire may ...
SERVICING AND MAINTENANCE BODYWORK sent higher levels of performance on the WARNING! laboratory test wheel, than the minimum Protection From Atmospheric Agents The traction grade assigned to this tire is required by law. based on straight-ahead braking traction Vehicle body care requirements vary according tests, and does not include acceleration, WARNING! to geographic locations and usage.
SERVICING AND MAINTENANCE What Causes Corrosion? Do not use abrasive cleaning components, CAUTION! solvents, steel wool or other aggressive mate- Corrosion is the result of deterioration or rial to clean the lenses. Do not use abrasive or strong cleaning removal of paint and protective coatings from materials such as steel wool or scouring your vehicle.
SERVICING AND MAINTENANCE If you carry special cargo such as chemicals, Stain Repel Fabric Cleaning Procedure — If If the belts need cleaning, use a mild soap solu- fertilizers, de-icer salt, etc., be sure that such tion or lukewarm water. Do not remove the belts Equipped materials are well packaged and sealed.
SERVICING AND MAINTENANCE Plastic And Coated Parts Leather Parts CAUTION! Use Mopar Total Clean to clean vinyl upholstery. Mopar Total Clean is specifically recommended Do not use Alcohol and Alcohol-based and/or for leather upholstery. Ketone based cleaning products to clean CAUTION! Your leather upholstery can be best preserved leather upholstery, as damage to the...
TECHNICAL SPECIFICATIONS IDENTIFICATION DATA NOTE: Hydraulic Brake Assist — If Equipped It is illegal to remove or alter the VIN. The brake system power assist is provided by a Vehicle Identification Number BRAKE SYSTEM hydro-boost unit which shares fluid with the The Vehicle Identification Number (VIN) is found power steering system.
TECHNICAL SPECIFICATIONS Torque Specifications interface between the hex and the washer. Retighten the wheel nuts in the same sequence Ensure that the socket is fully engaged on the to the torques listed in the table. Go through the Lug Nut/ Lug Nut/ **Lug Lug Nut/...
TECHNICAL SPECIFICATIONS FUEL REQUIREMENTS — GAS ENGINE All wheel nuts should be tightened occasionally Poor quality gasoline can cause problems such to eliminate the possibility of wheel studs being as hard starting, stalling, and hesitations. If you 6.4L Engine sheared or the bolt holes in the wheels experience these symptoms, try another brand of gasoline before considering service for the becoming elongated.
TECHNICAL SPECIFICATIONS Materials Added To Fuel Gasoline/Oxygenate Blends Do Not Use E-85 In Non-Flex Fuel Vehicles Besides using unleaded gasoline with the Some fuel suppliers blend unleaded gasoline Non-Flex Fuel Vehicles (FFV) are compatible proper octane rating, gasolines that contain with oxygenates such as ethanol.
TECHNICAL SPECIFICATIONS MMT In Gasoline Carbon Monoxide Warnings CAUTION! (Continued) Methylcyclopentadienyl Manganese Tricarbonyl WARNING! An out-of-tune engine or certain fuel or igni- (MMT) is a manganese-containing metallic addi- tion malfunctions can cause the catalytic tive that is blended into some gasoline to Carbon monoxide (CO) in exhaust gases is converter to overheat.
TECHNICAL SPECIFICATIONS FUEL REQUIREMENTS – DIESEL ENGINE Diesel fuel is seldom completely free of water. NOTE: To prevent fuel system trouble, drain the accu- If you accidentally fill the fuel tank with gaso- Use good quality diesel fuel from a reputable ...
TECHNICAL SPECIFICATIONS Biodiesel Fuel Requirements Biodiesel is a fuel produced from renewable Fuel Oxidation Stability — Must Use Fuel resources typically derived from animal fat, Within Six Months Of Manufacture Chassis Cab Models rapeseed oil (Rapeseed Methyl Ester (RME) Biodiesel fuel has poor oxidation stability which A maximum blend of 5% biodiesel meeting base), or soybean oil (Soy Methyl Ester (SME or can result in long term storage problems.
TECHNICAL SPECIFICATIONS VEHICLE SPECIFCATIONS Fuel In Oil Dilution — Must Adhere To CAUTION! Required Oil Change Interval Under no circumstances should oil change Engine 6.4L Fuel dilution of lubricating oil has been intervals exceed 12,500 miles observed with the use of biodiesel fuel. Fuel in Power 340 kW @ 6,000 RPM (20,000 km) if operation occurs with...
TECHNICAL SPECIFICATIONS FLUIDS AND LUBRICANTS — GAS ENGINE Engine Component Fluid, Lubricant, or Genuine Part We recommend you use Mopar Antifreeze/Coolant 10–Year/150,000 Engine Coolant Mile Formula OAT (Organic Additive Technology). For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet the American Petroleum Institute (API) categories of Engine Oil –...
Page 410
TECHNICAL SPECIFICATIONS CAUTION! CAUTION! (Continued) CAUTION! (Continued) Mixing of engine coolant (antifreeze) other Do not use water alone or alcohol-based This vehicle has not been designed for use than specified Organic Additive Technology engine coolant (antifreeze) products. Do with propylene glycol-based engine coolant (OAT) engine coolant (antifreeze), may not use additional rust inhibitors or antirust...
TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part Use only Mopar ZF 8&9 Speed ATF Automatic Transmission Fluid, Automatic Transmission – Eight-Speed orequivalent. Failure to use the correct fluid may affect the function orperformance of your transmission. Use only Mopar ASRC Automatic Transmission Fluid or equivalent. Failure Automatic Transmission –...
TECHNICAL SPECIFICATIONS FLUIDS AND LUBRICANTS — DIESEL ENGINE Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). In ambient temperatures above 0°F (-18°C), we recommend you use 10W-30 engine oil such as Mopar, Shell Rotella and Shell Rimula that meets FCA Material Standard MS-10902 and the API CK-4 engine oil category is required.
Page 413
TECHNICAL SPECIFICATIONS Component Fluid, Lubricant, or Genuine Part Use good quality diesel fuel from a reputable supplier in your vehicle. Federal law requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system.
TECHNICAL SPECIFICATIONS Chassis Component Fluid, Lubricant, or Genuine Part Only use Mopar ASRC Automatic Transmission Fluid or equivalent. Failure Automatic Transmission to use the proper fluid may affect the function or performance of your transmission. Transfer Case We recommend you use Mopar BW44–44 Transfer Case Fluid. We recommend you use SAE 75W-85 HD Ram GL-5 Synthetic Axle Lubricant in 9.25 Front &...
TECHNICAL SPECIFICATIONS MOPAR ACCESSORIES Authentic Accessories By Mopar In choosing Authentic Accessories you gain far more than expressive style, premium protection, or extreme entertainment, you also benefit from enhancing your vehicle with accessories that have been thoroughly tested and factory-approved. The following highlights just some of the many Authentic Ram Accessories by Mopar featuring a fit, finish, and functionality specifically for your Ram.
MULTIMEDIA UCONNECT SYSTEMS Your vehicle may be equipped with certain secu- WARNING! rity features to reduce the risk of unauthorized For detailed information about your Uconnect and unlawful access to vehicle systems and It is not possible to know or to predict all of ...
MULTIMEDIA UCONNECT SETTINGS NOTE: allows you to access programmable features that may be equipped such as Display, Units, FCA US LLC or your dealer may contact you The Uconnect system uses a combination of Voice, Clock, Safety/Assistance, Lights, Doors & directly regarding software updates.
Page 418
MULTIMEDIA Display After pressing the Display button on the touchscreen, the following settings will be available. Setting Name Selectable Options Display Mode Auto Manual Set Language English, Français, Español Touchscreen Beep Fuel Saver Display NOTE: The “Fuel Saver Display” feature will allow you to enable fuel saver mode and will be displayed in the instrument cluster display. Units —...
Page 419
MULTIMEDIA Voice After pressing the Voice button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Always With Help Never Clock After pressing the Clock button on the touchscreen, the following settings will be available: Setting Name Selectable Options Set Time...
Page 420
MULTIMEDIA Setting Name Selectable Options Rear ParkSense Chime Volume — If High Equipped Tilt Side Mirrors In Reverse — If Equipped NOTE: When the “Tilt Side Mirrors In Reverse” feature is selected, the exterior side-view mirrors tilt downward when the ignition is in the ON/RUN position and the transmission gear selector is in the REVERSE position.
Page 421
MULTIMEDIA Setting Name Selectable Options Surround View Camera Guidelines — If Equipped NOTE: The “Surround View Camera Guidelines” feature allows you to see active guidelines over the Surround View camera display whenever the gear selector is put into REVERSE or the Surround View button on the touchscreen is pressed. The image will be displayed on the radio touchscreen display. ParkView Backup Camera Active Guidelines NOTE:...
Page 422
MULTIMEDIA Setting Name Selectable Options Forward Facing Camera Guidelines — If Equipped NOTE: The “Forward Facing Camera Guidelines” feature is an off-road type of feature that shows the path of the tires based on the steering wheel input. CHMSL (Center High Mounted Stop Lamp) Camera Dynamic Centerline —...
Page 423
MULTIMEDIA Lights After pressing the Lights button on the touchscreen, the following settings will be available: Setting Name Selectable Options Headlight Off Delay 0 sec 30 sec 60 sec 90 sec Headlight Illumination On Approach 0 sec 30 sec 60 sec 90 sec NOTE: When the “Headlight Illumination On Approach”...
Page 424
MULTIMEDIA Setting Name Selectable Options Flash Lights With Lock NOTE: When the “Flash Lights With Lock” feature is selected, the exterior lights flash when the doors are locked or unlocked with the key fob. This feature may be selected with or without the “Sound Horn With Lock” feature selected. Steering Directed Lights NOTE: When the “Steering Directed Lights”...
Page 425
MULTIMEDIA Doors & Locks After pressing the Doors & Locks button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto Door Locks — If Equipped NOTE: When the “Auto Door Locks” feature is selected, all doors lock automatically when the vehicle reaches a speed of 15 mph (24 km/h). Auto Unlock On Exit NOTE: When the “Auto Unlock On Exit”...
Page 426
MULTIMEDIA Setting Name Selectable Options Passive Entry — If Equipped NOTE: The “Passive Entry” feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons. It automat- ically unlocks the doors when the outside door handle is grabbed. Flash Lights With Lock NOTE: When the “Flash Lights With Lock”...
Page 427
MULTIMEDIA Engine Off Options After pressing the Engine Off Options button on the touchscreen, the following settings will be available: Setting Name Selectable Options Easy Exit Seats — If Equipped Headlight Off Delay 0 sec 30 sec 60 sec 90 sec Engine Off Power Delay 0 sec 45 sec...
Page 428
MULTIMEDIA Setting Name Selectable Options Wheel Alignment Mode NOTE: The “Wheel Alignment Mode” feature prevents auto leveling of the air suspension while performing a wheel alignment service. Before performing a wheel alignment, this mode must be enabled. Refer to an authorized dealer for further information. Trailer Brake After pressing the Trailer Brake button on the touchscreen, the following settings will be available: Setting Name...
Page 429
MULTIMEDIA Setting Name Selectable Options Equalizer – NOTE: When in the “Equalizer” display you may adjust the Bass, Mid and Treble settings. Speed Adjusted Volume NOTE: The “Speed Adjusted Volume” feature increases or decreases volume relative to vehicle speed. Surround Sound — If Equipped NOTE: The “Surround Sound”...
Page 430
MULTIMEDIA Setting Name Selectable Options NOTE: The “Paired Phones” feature shows which phones are paired to the Phone/Bluetooth® system. For further information, refer to “Phone Operation” in “Uconnect 3 with 5-inch Display” section for further details. SiriusXM® Setup — If Equipped After pressing the SiriusXM®...
Page 431
MULTIMEDIA Restore Default Settings After pressing the Restore Default Settings button on the touchscreen, the following settings will be available: Setting Name Selectable Options Restore Default Settings Cancel NOTE: When the “Restore Default Settings” feature is selected it will reset the Display, Clock, Audio, and Radio Settings to their default settings. If “Yes” is selected a pop-up will appear asking "Are you sure you want to reset your settings to default?”...
MULTIMEDIA Uconnect 4/4C/4C NAV Settings Press the Apps button on the touchscreen then NOTE: press the Settings button on the touchscreen to Only one category may be selected at a time. display the settings menu screen. In this mode When making a selection, press the button on the Uconnect system allows you to access the touchscreen to enter the desired mode.
Page 433
MULTIMEDIA Language After pressing the Language button on the touchscreen, the following settings will be available: Setting Name Selectable Options Set Language English Français Español NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Español) for all display nomenclature, including the trip functions and the navigation system (if equipped).
Page 434
MULTIMEDIA Setting Name Selectable Options Set Theme Selectable Options Touchscreen Beep Controls Screen Timeout — If Equipped Fuel Saver Display in Cluster — If Equipped NOTE: When selected, the system displays fuel saver mode in the instrument cluster. Navigation Next Turn-by-Turn Displayed — If Equipped Phone Pop-ups Displayed in Cluster —...
Page 435
MULTIMEDIA Setting Name Selectable Options Power — If Equipped HP (US) HP (UK) Temperature °F °C Torque — If Equipped lb-ft Voice After pressing the Voice button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed...
Page 436
MULTIMEDIA Camera After pressing the Camera button on the touchscreen, the following settings will be available: Setting Name Selectable Options Surround View Camera — If Equipped NOTE: The “Surround View Camera” feature displays a complete 360 degree view of the vehicle's exterior environment while backing up. Surround View Camera Delay —...
Page 437
MULTIMEDIA Setting Name Selectable Options Fixed Backup Camera Guidelines — If Equipped Forward Facing Camera Guidelines — If Equipped NOTE: The “Forward Facing Camera Guidelines” feature is an off-road type of feature that shows the path of the tires based on the steering wheel input. CHMSL (Center High Mounted Stop Lamp) Camera Dynamic Centerline —...
Page 438
MULTIMEDIA Setting Name Selectable Options Forward Collision Warning Near Sensitivity — If Equipped NOTE: Sets the distance in which a Forward Collision Warning occurs. Front ParkSense Volume High Rear ParkSense Volume High Power Side Steps — If Equipped Auto Store Blind Spot Alert Lights Lights &...
Page 439
MULTIMEDIA Lights After pressing the Lights button on the touchscreen, the following settings will be available: Setting Name Selectable Options Headlight Off Delay – NOTE: When the “Headlight Off Delay” feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle.
Page 440
MULTIMEDIA Setting Name Selectable Options Flash Lights With Lock NOTE: When the “Flash Lights With Lock” feature is selected, the exterior lamps flash when the doors are locked or unlocked with the key fob. This feature may be selected with or without the “Sound Horn With Lock” feature selected. Rear Guidance Lights w/ Cargo Lights —...
Page 441
MULTIMEDIA Setting Name Selectable Options Flash Lights With Lock NOTE: When the “Flash Lights With Lock” feature is selected, the front and rear turn signals flash when the doors are locked or unlocked with the key fob. This feature may be selected with or without the “Sound Horn With Lock” feature selected. Sound Horn With Lock 1st Press 2nd Press...
Page 442
MULTIMEDIA Setting Name Selectable Options Personal Settings Linked To Key Fob — If Equipped NOTE: The “Personal Settings Linked To Key Fob” feature provides automatic driver seat positioning to enhance driver mobility when entering and exiting the vehicle. The seats return to the memorized seat location (if “Personal Settings Linked To Key Fob” is set to On) when the key fob is used to unlock the door. ...
Page 443
MULTIMEDIA Key Off Options After pressing the Key Off Options button on the touchscreen, the following settings will be available: Setting Name Selectable Options Key Off Power Delay – NOTE: When the “Key Off Power Delay” feature is selected, the power window switches, radio, Uconnect phone system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to OFF.
Page 444
MULTIMEDIA Air Suspension — If Equipped After pressing the Suspension button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Suspension Messages Warnings Only Tire Jack Mode NOTE: When the “Tire Jack Mode” feature is selected, the air suspension system is disabled to assist with changing a spare tire. Transport Mode NOTE: When the “Transport Mode”...
Page 445
MULTIMEDIA Trailer After pressing the Trailer button on the touchscreen, the following settings will be available: Setting Name Selectable Options Trailer Trailer 1 Trailer 2 Trailer 3 Trailer 4 Once selecting the specific trailer, the following programmable options become available: Setting Name Selectable Options Use This Trailer...
Page 446
MULTIMEDIA Setting Name Selectable Options Trailer Name List of Trailer Names NOTE: You can select and personalize your trailer name depending on the type of trailer you are hauling. Select the trailer name from the following list: trailer, boat, car, cargo, dump, equipment, flatbed, gooseneck, horse, livestock, motorcycle, snowmobile, travel, utility, and 5th wheel. NOTE: For further information about Trailer Tire Pressure Monitoring, refer to “Auxiliary Driving Systems”...
Page 447
MULTIMEDIA Setting Name Selectable Options Surround Sound — If Equipped NOTE: The “Surround Sound” feature provides simulated surround sound mode. AUX Volume Offset — If Equipped NOTE: The “AUX Volume Offset” feature provides the ability to tune the audio level for portable devices connected through the AUX input. Auto Play Phone/Bluetooth®...
Page 448
MULTIMEDIA Setting Name Selectable Options Paired Phones and Audio Devices List Of Paired Phones and Audio Sources NOTE: The “Paired Phones and Audio Devices” feature shows which phones and audio sources are paired to the Phone and Audio Sources Settings system. For further information, refer to the Uconnect Owner’s Manual Supplement.
Page 449
MULTIMEDIA Setting Name Selectable Options Subscription Information Sirius ID NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM® Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe. 1.
Page 450
MULTIMEDIA Clear Personal Data After pressing the Clear Personal Data Settings button on the touchscreen, the following settings will be available: Setting Name Selectable Options Clear Personal Data Cancel NOTE: When this feature is selected it will remove all personal data including Bluetooth® devices and presets. If “Yes” is selected a pop-up will appear asking "Are you sure you want to clear all personal data?”...
MULTIMEDIA Uconnect 4C NAV With 12-inch Display Settings Press the Settings button on the touchscreen to When making a selection, press the button on the touchscreen to enter the desired mode. display the settings menu screen. In this mode the Uconnect system allows you to access Once in the desired mode, press and release programmable features that may be equipped the preferred setting until a check-mark...
Page 452
MULTIMEDIA Language After pressing the Language button on the touchscreen, the following settings will be available: Setting Name Selectable Options Language English Español Français NOTE: When the “Language” feature is selected, you may select one of multiple languages (English / Français / Español) for all display nomenclature, including the trip functions and the navigation system.
Page 453
MULTIMEDIA Setting Name Selectable Options Touchscreen Beep Controls Screen Time-Out — If Equipped Fuel Saver Display — If Equipped NOTE: When selected, the system displays fuel saver mode in the instrument cluster. Navigation Turn-By-Turn Displayed in Cluster — If Equipped Phone Pop-Ups Displays In Cluster Ready To Drive Pop-Ups —...
Page 454
MULTIMEDIA Setting Name Selectable Options Temperature °F °C Torque — If Equipped lb-ft Voice After pressing the Voice button on the touchscreen, the following settings will be available: Setting Name Selectable Options Voice Response Length Brief Detailed Show Command List Always w/Help Never...
Page 455
MULTIMEDIA Camera After pressing the Camera button on the touchscreen, the following settings will be available: Setting Name Selectable Options Surround View Camera — If Equipped NOTE: The “Surround View Camera” feature displays a complete 360 degree view of the vehicle's exterior environment while backing up. Surround View Camera Delay —...
Page 456
MULTIMEDIA Setting Name Selectable Options Active Backup Camera Guidelines — If Equipped NOTE: The “Active Backup Camera Guidelines” feature overlays the Rear Backup Camera image with active, or dynamic, grid lines to help illustrate the width of the vehicle and its projected backup path, based on the steering wheel position when the option is checked. A dashed center line overlay indicates the center of the vehicle to assist with parking or aligning to a hitch/receiver.
Page 457
MULTIMEDIA Safety & Driving Assistance After pressing the Safety & Driving Assistance button on the touchscreen, the following settings will be available: Setting Name Selectable Options Forward Collision Warning — If Warning Only Warning & Active Braking Equipped NOTE: Sounds an audible warning for the driver to slow the vehicle in case of collision or sounds an audible warning and applies brakes. Forward Collision Warning Near Sensitivity —...
Page 458
MULTIMEDIA Mirrors & Wipers After pressing the Mirror and Wipers button on the touchscreen, the following settings will be available: Setting Name Selectable Options Tilt Side Mirrors In Reverse — If Equipped NOTE: When the “Tilt Side Mirrors In Reverse” feature is selected, the outside side-view mirrors will tilt downward when the ignition is in the ON/RUN position and the transmission gear selector is in the REVERSE position.
Page 459
MULTIMEDIA Setting Name Selectable Options Headlights With Wipers — If Equipped NOTE: When the “Headlights With Wipers” feature is selected, and the headlight switch is in the AUTO position, the headlights turn on approximately 10 seconds after the wipers are turned on. The headlights also turn off when the wipers are turned off if they were turned on by this feature. Auto Dim High Beams —...
Page 460
MULTIMEDIA Doors & Locks After pressing the Doors & Locks button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto Door Locks Auto Unlock On Exit NOTE: When the “Auto Unlock On Exit” feature is selected, all doors unlock when the vehicle is stopped and the transmission is in the PARK or NEUTRAL position and the driver's door is opened.
Page 461
MULTIMEDIA Setting Name Selectable Options Passive Entry — If Equipped NOTE: The “Passive Entry” feature allows you to lock and unlock the vehicle’s door(s) without having to push the key fob lock or unlock buttons. Personal Settings Linked To Key Fob — If Equipped NOTE: The “Personal Settings Linked To Key Fob”...
Page 462
MULTIMEDIA Key Off Options After pressing the Key Off Options button on the touchscreen, the following settings will be available: Setting Name Selectable Options Key Off Power Delay – NOTE: When the “Key Off Power Delay” feature is selected, the power window switches, radio, Uconnect phone system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition is cycled to OFF.
Page 463
MULTIMEDIA Setting Name Selectable Options Transport Mode NOTE: When the “Transport Mode” feature is selected, the air suspension system lowers and then disables to assist with flat bed towing. Wheel Alignment Mode NOTE: Before performing a wheel alignment, the “Wheel Alignment Mode” must be enabled. Refer to an authorized dealer for further information. Trailer After pressing the Trailer button on the touchscreen, the following settings will be available: Setting Name...
Page 464
MULTIMEDIA Setting Name Selectable Options Tire Pressure Are you sure you want to delete the Tire Pressure Settings for Trailer 1? Number Of Axles Number Of Tires NOTE: After pressing Next, the Tire Pressure screen appears. The default for this option is 50 PSI (344 kPa), however the range is selectable anywhere between 25–125 PSI (172–862 kPa).
Page 465
MULTIMEDIA Audio After pressing the Audio button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Front Right Back Left NOTE: The “Balance/Fade” feature allows you to adjust the Balance and Fade settings. Press and drag the Speaker icon or use the arrows to adjust, tap the C icon to readjust to the center.
Page 466
MULTIMEDIA Bluetooth® After pressing the Bluetooth® button on the touchscreen, the following settings will be available: Setting Name Selectable Options Phone Pop-Ups Displayed in Cluster Do Not Disturb List of Settings NOTE: Press “Do Not Disturb” to access the available settings. The following settings are: Auto Reply (Both, Text, Call), Auto Reply Message (Custom, Default) and Custom Auto Reply Message (Create Message).
Page 467
MULTIMEDIA SiriusXM® Setup — If Equipped After pressing the SiriusXM® Setup button on the touchscreen, the following settings will be available: Setting Name Selectable Options Sirius All Access Choose a Subscription Package Add Listener Add up to five profiles NOTE: The “Add Listener”...
Page 468
MULTIMEDIA Setting Name Selectable Options Subscription Information Sirius ID NOTE: New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM® Satellite Radio with your radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription Information screen to re-subscribe. 1.
MULTIMEDIA SAFETY AND GENERAL INFORMATION Glance at the screen only when safe to do so. Keep drinks, rain and other sources of mois- If prolonged viewing of the screen is required, ture away from the system. Besides damage Safety Guidelines park in a safe location and set the parking to the system, moisture can cause electric...
MULTIMEDIA UCONNECT 3 WITH 5-INCH DISPLAY Care And Maintenance 4 — MORE Push the MORE button on the faceplate to Touchscreen Introduction access additional options. Do not press the touchscreen with any hard or sharp objects (pen, USB stick, jewelry, 5 —...
MULTIMEDIA 10 — MEDIA The radio is equipped with the following modes: TUNE/SCROLL Control Pushing the MEDIA button on the faceplate will Turn the rotary TUNE/SCROLL control knob allow you to switch to Media mode: CD (if clockwise to increase or counterclockwise to ...
Page 472
MULTIMEDIA Seek Down SiriusXM® Satellite Radio Mode — If and programming subject to change. Our satel- Equipped lite service is available only to those at least 18 Press and release the Seek Down button on the and older in the 48 contiguous USA and D.C. touchscreen to tune the radio to the next listen- SiriusXM®...
Page 473
MULTIMEDIA When you are receiving a station that you wish Equalizer — Press the Equalizer button on Loudness — Press the Loudness button to commit into memory, press and hold the the touchscreen to adjust the Bass, Mid on the touchscreen to select the Loud- desired numbered button on the touchscreen and Treble.
MULTIMEDIA Media Mode Audio Source Selection Seek Up/Seek Down Functions Once in Media Mode, press the Source button Seek Up /Seek Down Operating Media Mode on the touchscreen and the desired mode Press and release the Seek Up button on the button on the touchscreen.
Page 475
MULTIMEDIA Repeat USB/IPOD® MODE BLUETOOTH® MODE Press the Repeat button on the touchscreen to USB/iPod® Mode is entered by either inserting Bluetooth® Streaming Audio (BTSA) or repeat the song selection. To cancel Repeat, a USB Jump Drive or iPod® cable into the USB Bluetooth®...
MULTIMEDIA Inserting Auxiliary Device Phone Mode The Uconnect Phone is a voice-activated, hands-free, in-vehicle communications system Gently insert the Auxiliary device cable into the Operating Phone Mode with voice command capability. Refer to Voice AUX Port. If you insert an Auxiliary device with Recognition (VR) within this publication for the ignition on, the unit will switch to AUX mode further information.
Page 477
MULTIMEDIA Main Functions Connecting/Disconnecting A Mobile Phone NOTE: Or Bluetooth® Device The buttons on the display can be used to: You must have Bluetooth® enabled on your Compose phone numbers using the graphic phone to complete this procedure. Pairing A Phone keypad on the display.
Page 478
MULTIMEDIA 4. Search for available devices on your Blue- If No is selected and you still would like to 8. When the pairing process has successfully tooth®-enabled mobile phone. pair a mobile phone, press the Settings but- completed, the system will prompt you to ton from the Uconnect Phone main screen.
Page 479
MULTIMEDIA Storing Names/Numbers in The Mobile Phone 3. Select the Paired Phones or Paired Audio Deletion Of A Mobile Phone Or A Bluetooth® list using the corresponding button on the Audio Device Before pairing your mobile phone, you must display. make sure you have stored the names you want To delete a mobile phone or Bluetooth®...
Page 480
MULTIMEDIA Setting A Mobile Phone Or A Bluetooth® If equipped and specifically supported by your Only the phonebook of the currently connected mobile phone is accessible. Audio Device As A Favorite phone, Uconnect Phone asks you if you want to download names (text names) and number To set a mobile phone or Bluetooth®...
Page 481
MULTIMEDIA Making A Phone Call Calls without a reply Ignore Dialing The Phone Number Using The All calls Put on hold/resume "Keyboard" Icon On The Display To access these types of calls, press the Recent Deactivate/activate the microphone ...
Page 482
MULTIMEDIA Managing Two Phone Calls Ending A Call When a text message is received, the display will show a screen where the options "Listen", If two calls are in progress (one active and one Press the End button on the touchscreen or the "Call"...
MULTIMEDIA STEERING WHEEL AUDIO CONTROLS — IF IPOD®/USB/MP3 CONTROL — IF EQUIPPED The left-hand control is a rocker type switch with a push-button in the center. The function of the EQUIPPED Located on the center stack, just below the left-hand control is different depending on instrument panel, is the main media hub.
Page 484
MULTIMEDIA For example, if a device is plugged into the Type Applicable to only Uconnect 4C/4C NAV With A USB port and another device is plugged into 8.4-inch Display, and Uconnect 4C NAV With the Type C USB port, a message will appear and 12-inch Display radios, different scenarios are allow you to select which device to use.
MULTIMEDIA If equipped, two Mini-USB Ports (Type C), two NOTE: Standard USB Ports (Type A), and one AUX Port Plugging in a phone or another USB device may may be located to the left of the center stack, cause the connection to a previous device to be just below the climate controls.
MULTIMEDIA Regulatory And Safety Information This device complies with Part 15 of the FCC La operación de este equipo está sujeta a las Rules and with Innovation, Science, and siguientes dos condiciones: USA/CANADA Economic Development Canada license-exempt 1. es posible que este equipo o dispositivo no Exposure to Radio Frequency Radiation RSS standard(s).
MULTIMEDIA If this equipment does cause harmful inter- Get Started ference to radio or television reception, All you need to control your Uconnect system which can be determined by turning the with your voice are the buttons on your steering equipment off and on, the user is encour- wheel.
MULTIMEDIA Notice the visual cues that inform you of your Radio voice recognition system’s status. Cues appear Use your voice to quickly get to the AM, FM or on the top of the touchscreen. SiriusXM® Satellite Radio stations you would like to hear.
Page 489
MULTIMEDIA TIP: At any time, if you are not sure of what to say or want to learn a Voice Command, push the VR button on the steering wheel and say “Help.” The system provides you with a list of commands.
MULTIMEDIA Media Voice Command must match exactly how the artist, album, song and genre information is Uconnect offers connections via USB, Blue- displayed. tooth® and auxiliary ports (if equipped). Voice operation is only available for connected USB and AUX devices. (Remote CD player optional and not available on all vehicles.) Push the VR button on the steering wheel.
MULTIMEDIA Phone Making and answering hands-free phone calls is easy with Uconnect. When the Phonebook button is illuminated on your touchscreen, your system is ready. Check UconnectPhone.com mobile phone compatibility and pairing instruc- tions. Push the Phone button . After the beep, say one of the following commands: Uconnect 3 Phone “Call John Smith”...
MULTIMEDIA Voice Text Reply — If Equipped NOTE: PRE-DEFINED VOICE TEXT REPLY Only use the numbering listed, otherwise the Uconnect announces incoming text messages. RESPONSES system does not transpose the message. Push the VR button on the steering wheel or Stuck in Yes.
MULTIMEDIA Climate (4C/4C NAV) Too hot? Too cold? Adjust vehicle temperatures hands-free and keep everyone comfortable while you keep moving ahead. (If vehicle is equipped with climate control.) Push the VR button on the steering wheel. After the beep, say one of the following commands: “Set driver temperature to 70 degrees”...
MULTIMEDIA Navigation (4C NAV) SiriusXM Guardian™ (4C/4C NAV) — If Equipped The Uconnect navigation feature helps you save time and become more productive when you CAUTION! know exactly how to get to where you want to go. Some SiriusXM Guardian™ services, 1.
MULTIMEDIA NOTE: Register (4C/4C NAV) Mobile App (4C/4C NAV) SiriusXM Guardian™ is available only on To unlock the full potential of SiriusXM You’re only a few steps away from using remote equipped vehicles purchased within the conti- Guardian™ in your vehicle, you must activate commands and playing your favorite music in nental United States, Alaska, Hawaii, and your SiriusXM Guardian™...
MULTIMEDIA Press the Location button on the navigation TIP: bar at the bottom of the app to bring up a Traffic alerts are not accessible with Voice map to locate your vehicle or send a location Command. to your vehicle’s navigation system. Press the Settings button in the upper left ...
MULTIMEDIA Siri® Eyes Free — If Equipped Siri lets you use your voice to send text messages, select media, place phone calls and much more. Siri uses your natural language to understand what you mean and responds back to confirm your requests. The system is designed to keep your eyes on the road and your hands on the wheel by letting Siri help you perform useful tasks.
MULTIMEDIA Using Do Not Disturb NOTE: button on the steering wheel, or press and hold the “Microphone” icon within Android Auto™, to With Do Not Disturb, you can disable notifica- Only the beginning of your custom message activate Android’s™ VR, which recognizes tions from incoming calls and texts, allowing will be seen on the touchscreen.
MULTIMEDIA Refer to your Uconnect Owner’s Manual Supple- Home button within Apple CarPlay®, to activate ment for further information. Siri, which recognizes natural voice commands to use a list of your iPhone’s® features: NOTE: Phone Requires compatible smartphone running Android™...
Refer to your Uconnect Owner’s Manual Supple- General Information ment for further information. The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this NOTE: vehicle: Requires compatible iPhone®. See dealer for phone compatibility. Data plan rates apply. This device complies with Part 15 of the FCC Vehicle user interface is a product of Apple®.
CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE Be Reasonable With Requests This is why you should always talk to an autho- rized dealer service manager first. Most matters FOR YOUR VEHICLE If you list a number of items and you must have can be resolved with this process.
CUSTOMER ASSISTANCE FCA US LLC Customer Center Customer Assistance For The Hearing Or and an Owner Identification Card in the mail within three weeks of the vehicle delivery date. Speech Impaired (TDD/TTY) P.O. Box 21–8004 If you have any questions about the service To assist customers who have hearing difficul- Auburn Hills, MI 48321–8004 contract, call the manufacturer's Service...
CUSTOMER ASSISTANCE REPORTING SAFETY DEFECTS To contact NHTSA, you may call the WARNING! Vehicle Safety Hotline toll free at In The 50 United States And Engine exhaust (internal combustion engines 1-888-327-4236 (TTY: Washington, D.C. only), some of its constituents, and certain 1-800-424-9153);...
CUSTOMER ASSISTANCE PUBLICATION ORDER FORMS Diagnostic Procedure Manuals Owner's Manuals Diagnostic Procedure Manuals are filled with These Owner's Manuals have been prepared To order the following manuals, you may use diagrams, charts and detailed illustrations. with the assistance of service and engineering either the website or the phone numbers listed These practical manuals make it easy for specialists to acquaint you with specific FCA US...
INDEX ....351 ....... 46 Air Conditioner Maintenance Automatic Headlights ..........413 ....351 ..62 Accessories Air Conditioner Refrigerant Automatic Temperature Control (ATC) ..........413 ......351 ....213 Mopar Air Conditioner System Automatic Transmission ......... 52 ........370 Adaptive Cruise Control (ACC) (Cruise Air Conditioning Adding Fluid ..........232...
Page 507
B-Pillar Location ........379 Changing A Flat Tire ....... 314 Cooling Capacity ........ 405 Brake Assist System .......121 Charge Air Cooler ........366 Disposal Of Used Coolant ....365 Brake Control System ......121 Chart, Tire Sizing ........376 Drain, Flush, And Refill ......
Page 515
The driver’s primary responsibility is the safe operation of the vehicle. Driving while distracted can result in loss of vehicle control, resulting in an accident and personal injury. FCA US LLC strongly recommends that the driver use extreme caution when using any device or feature that may take their attention off the road.
Page 516
Whether it is providing information about specific product features, taking a tour through your vehicle’s heritage, knowing what steps to take following an accident or scheduling your next appointment, we know you will find the app an important extension of your Ram vehicle. Simply download the app, select your make and model and enjoy the ride.
Need help?
Do you have a question about the CHASSIS CAB 2020 and is the answer not in the manual?
Questions and answers