Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please ELF has developed a complete range of lubricants for RENAULT: refer to your maintenance document. engine oils manual and automatic gearbox oils...
Page 3
This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
KEY/RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Radio frequency remote control unit Driver’s responsibility 1 Key for ignition switch, doors and Never leave your vehicle fuel filler cap. with the key or remote con- 2 Unlocking the front doors or all doors trol inside and never leave a and tailgate.
Page 9
KEY/RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the environ- ment: take care not to lock or unlock the doors by inadvertently pressing the For replacement, or if you buttons on the remote control. require an additional remote control.
RADIO FREQUENCY REMOTE CONTROL: use Deadlocking of the doors and The side indicator lights and hazard warning lights flash once to indicate tailgate that the doors have unlocked. If fitted to the vehicle, this allows the Special notes (for some countries): doors to be locked and prevents them from being opened with the interior pressing button 2 once unlocks only...
DOORS (1/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves Opening from the outside Lights-on reminder buzzer or to others by starting the engine, Unlock the door and pull handle 1.
DOORS (2/2) If there is any ice or snow prevent- ing the window from lowering when the door is opened, this ice or snow must be removed to free the window before the door is closed. If you pull handle 3 with- out opening the door, the window lowers by a few centimetres then closes...
LOCKING/UNLOCKING THE DOORS (1/2) Locking the opening elements without the remote control With the engine off, the rear doors closed and a front door open, press switch 1 for more than five seconds. Make sure you have your key with you before you leave your vehicle.
LOCKING/UNLOCKING THE DOORS (2/2) Doors and tailgate status indicator light When the ignition is on, the indicator light integrated in switch 1 informs you of the status of the doors and tailgate: – indicator light on, the doors and tail- gate are locked;...
AUTOMATIC LOCKING WHEN DRIVING (RAID) Operating principle Operating faults When the engine is started, the system If you notice an operating fault (auto- automatically locks the doors when the matic locking impossible), first check vehicle reaches a speed of approxi- that all doors are correctly locked.
FRONT HEADRESTS To remove the headrest Raise it to its highest position. Press button 2 and lift the headrest to release Note: when the headrest is removed, take care not to change the positions of the rods. To refit it If the setting of the rods has been al- tered, pull them fully upwards.
FRONT SEATS (1/2) To move forwards or backwards Depending on the seat, lift handle 2 to We would advise you not release it. Release the handle at the to recline the seatbacks too desired position and make sure that it far to ensure that the effec- is locked.
Page 18
FRONT SEATS (2/2) Access to the rear seats To tilt the front seat from the rear seats, pull strap 4 and slide the seat forwards. Lower handle 3 then keep it lowered Check that no object or To bring the seat into position, bring the while tilting the seatback and slide the person prevents the front seatback into position.
REAR VIEW MIRRORS Folding door mirrors Move button 2 to position F to fold the door mirrors in. To reset them for driv- ing, return to position D. If you fold the door mirrors in manually before resetting them to driving posi- tion D, you must first turn button 2 to position F.
SEAT BELTS (1/3) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
Page 21
SEAT BELTS (2/3) Driver seat belt reminder ß warning light It remains on when the engine is started if your seat belt is not fas- tened. An audible warning sounds at a low volume for 30 seconds, then at a high volume for 90 seconds.
Page 22
SEAT BELTS (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. For special operations (e.g. fitting child seats) contact an approved dealer. –...
REAR SEAT BELTS Rear side seat belts Snap the last sliding buckle 4 into red catch 5. Unwind belt 1 slowly from its housing. Click buckle 2 into black catch 3. Check that the rear seat belts are positioned and op- erating correctly each time Rear seat functions the rear seats are moved.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/3) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt pretensioners; an accident. – air bags 1 for driver and front pas- –...
Page 25
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/3) Air bags for driver and front Operation passenger This system is only operational when the ignition is switched on. It is fitted to the front seats on the driv- er’s side and, depending on the vehicle, In a severe frontal impact, the air bags on the passenger’s side as well.
Page 26
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/3) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
SIDE PROTECTION DEVICES Side air bags (depending on vehicle) This air bag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact.
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
Page 30
CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 31
CHILD SAFETY: Choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
CHILD SAFETY: choosing a child/baby seat mounting (1/2) There are two ways of attaching child Attachment using the ISOFIX Do not use the child seat seats: via the seat belt or using the system if it may unfasten the seat ISOFIX system.
Page 33
CHILD SAFETY: choosing a child/baby seat mounting (2/2) anchoring points (rings) in the luggage com- partment 3 cannot be used if they are already being used to mount other components: luggage net + load in the luggage compartment or child/baby seat + load in the luggage compartment.
CHILD SAFETY: fitting a child seat (1/3) Some seats are not suitable for fitting In the front seat In the rear seat child seats. The diagrams on the fol- The laws concerning children travel- A carrycot can be installed across the lowing pages show you how to attach ling in the front passenger seat differ in vehicle and will take up at least two...
Page 35
CHILD SAFETY: fitting a child seat (2/3) Child seats attached using the ISOFIX mounting ü Seat which allows an ISOFIX seat to be attached (depending on the ve- hicle). ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
Page 36
CHILD SAFETY: fitting a child seat (3/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Seat size Weight of Front passenger Type of child seat Rear side seats the child seat (1) (5)
CHILD SAFETY: deactivating/activating the front passenger air bag (1/3) Deactivating the front With the ignition on, you must check passenger air bag that the warning light 2 is lit on (on equipped vehicles) the central display and, depending on the vehicle, that the message “passen- You must deactivate the front passen- ger air bag off”...
Page 38
CHILD SAFETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER...
Page 41
DRIVING POSITION: LEFT-HAND DRIVE (2/2) 1 Stalk for: 7 Centre air vent. 18 Cigar lighter/12V accessories – direction indicator lights; socket. 8 Controls for ventilation, heating – exterior lights; – front fog lights; and de-icing. 19 Cup holder. – rear fog lights. 9 Location for passenger air bag.
DRIVING POSITION: RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side window demister outlet. 9 – Horn. 15 Location for radio, navigation – Location for driver’s air bag. system etc. 2 Side air vent. 10 Stalk for: 16 Gear lever.
Page 44
INSTRUMENT PANEL: warning lights (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Low fuel level warning light Coolant temperature warn- Ô This comes on when the igni- ing light tion is switched on and goes out after a If it comes on while you are driving, few seconds.
Page 45
INSTRUMENT PANEL: warning lights (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Main beam headlight tell-tale Brake pad wear warning á light light Depending on the vehicle, if the warn- Dipped beam headlight tell- ing light comes on, you must have your tale brake pads checked as soon as possi-...
Page 46
INSTRUMENT PANEL: warning lights (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Oil pressure warning light Electronic stability program À ù (ESP) and traction control If it comes on while you are (ASR) warning light driving, stop at once and switch off the ignition.
INSTRUMENT PANEL: display and indicators (1/2) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. Speedometer 1 Rev counter 2 Coolant temperature (scale x 1,000). indicator 4 Overspeed buzzer In normal use, the needle should be Depending on the vehicle, a beep Fuel gauge 3 before area B.
INSTRUMENT PANEL: display and indicators (2/2) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. – Display selection Press briefly to move from the total mileage to the trip mileage and vice versa.
Page 50
TRIP COMPUTER: general information (1/2) c) mileage before service; d) cruise control and speed limiter pro- grammed speed; e) trip log, operating faults and informa- tion message readout. Trip computer and warning Display selection keys 1 system A and 2 Depending on the vehicle, this includes Scroll through the following informa- the following functions:...
Page 51
TRIP COMPUTER AND WARNING SYSTEM: general information (2/2) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded.
Page 52
ON-BOARD COMPUTER: journey parameters (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected a) Total mileage and trip mileage recorder. FUEL USED 26.0 L b) Journey parameters Fuel consumed since the last reset. AVERAGE Average fuel consumption since the last reset.
Page 53
TRIP COMPUTER AND WARNING SYSTEM: trip parameters (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Estimated range with remaining fuel RANGE This range takes into account the average fuel consumption since the last time the reset - - - - KM button was pressed.
Page 54
TRIP COMPUTER AND WARNING SYSTEM: trip parameters (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected c) Distance before service SERVICE IN Distance remaining until the next service (displayed in kilometres), then when the 13770 KM service nears, several scenarios are possible: –...
Page 55
TRIP COMPUTER AND WARNING SYSTEM: trip parameters (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected SPEED LIMITER 70 KM/H d) Cruise control/speed limiter programmed speed (depending on the vehicle).
Page 56
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpretation of messages “BOOT OPEN”...
Page 58
TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages.
CLOCK AND EXTERIOR TEMPERATURE Exterior temperature On equipped vehicles, the exterior tem- perature is displayed at A. If it is be- tween – 3 °C and + 3 °C, the °C charac- ters flash (signalling a risk of ice). If the power supply is cut (battery disconnected, supply wire cut, etc.), the clock must be reset.
STEERING WHEEL Steering wheel height adjustment Pull lever 1 and adjust the steering wheel to the required position; push the lever to lock the steering wheel. Make sure that the steering wheel is correctly locked. For safety reasons, only adjust the steering wheel when the vehicle is station- ary.
AUDIBLE AND VISUAL SIGNALS Horn Hazard warning lights Direction indicators é Press at one of the locations 2. Press switch 3. This switch ac- Move stalk 1 parallel to the steering tivates all four direction indicators and wheel and in the direction you are going the side indicator lights simultaneously.
EXTERNAL LIGHTING AND SIGNALS (1/3) Dipped beam Main beam headlights á headlights With stalk 1 in dipped beam headlights Manual operation position, move the stalk towards you. Turn the end of stalk 1 until the symbol The indicator light on the instrument is opposite mark 2.
Page 63
EXTERNAL LIGHTING AND SIGNALS (2/3) “See-me-home lighting” function (depending on vehicle) This function (useful, for example, for opening a gate, garage, etc.) enables you to switch the dipped headlights on momentarily. With the ignition off and the headlights off, pull stalk 1 towards you: the dipped beam headlights come on for approxi- mately sixty seconds.
EXTERNAL LIGHTING AND SIGNALS (3/3) Rear fog light The front fog lights and the side lights or dipped beam headlights must be on. Turn ring 5 on stalk 1 until the symbol is opposite mark 4, then release it. This indicator light on the instrument panel comes on.
Page 65
ELECTRICAL ADJUSTMENT OF THE DIPPED BEAM HEADLIGHTS 50 m 100 m Control knob 1 is used to adjust the A Incorrect setting: the lights are set height of the headlight beams accord- too high and could dazzle other ing to the load. drivers.
WINDSCREEN WASH/WIPE (1/2) Automatic wiper function (depending on vehicle) With the engine running, move stalk 1. A Park B Automatic wiper function When this position is selected, the system detects the presence of water on the windscreen and trig- gers wiping at a suitable wiping speed.
WINDSCREEN WASH/WIPE (2/2) Windscreen wiper With the ignition on, pull stalk 1 to- wards you. A brief pull will trigger a single sweep of the wipers, in addition to the wind- screen washer. A longer pull will trigger three sweeps of the wipers followed, a few seconds later, by a fourth, in addition to the wind- screen washer.
Page 68
REAR SCREEN WASH/WIPE Rear screen wash/wipe Turn the end of stalk 1 to posi- tion the symbol opposite mark 2. When the stalk is released, it returns to the rear screen wiper position. Note: when the rear screen is open, the rear screen wiper will not work.
FUEL TANK (1/2) Fuel grade Use a high-grade fuel that complies with the legislation in force in each country and which must conform to the specifications given on the label on cover A. Refer to the information on “Engine specifications” in Section 6. Diesel versions It is essential to use diesel fuel that conforms with the information given on...
Page 70
FUEL TANK (2/2) Filling with fuel Petrol versions Persistent smell of It is essential to use unleaded petrol. With the ignition off, insert the nozzle fuel The octane rating (RON) must conform so that the valve opens and then fully to the information given on the label on If you notice a persistent insert it before beginning to fill the tank...
Page 71
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Ignition switch .
RUNNING IN/IGNITION SWITCH Running in Ignition on position M The ignition is switched on: Petrol version – petrol version: you can start the ve- hicle; For the first 600 miles (1,000 km) do not exceed 54 mph (90 km/h) in the –...
STARTING/STOPPING THE ENGINE Stopping the engine Diesel versions É With the engine idling, turn the key to Turn the ignition key to the “Ignition the “Stop” position St. on” position M, and hold this position until the engine preheating warning light goes off.
GEAR LEVER To select reverse gear (vehicle stationary) Follow the grid marked on knob 1 and, depending on the vehicle, lift the ring against the knob to engage reverse An impact to the underside gear. of the vehicle (e.g.: striking a post, raised kerb or other The reversing lights will come on as street furniture) may result...
HANDBRAKE/POWER-ASSISTED STEERING Variable power-assisted To apply: steering Pull upwards, check that the vehicle is properly immobilised. The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for...
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed You may need to restart the operation if the vehicle has to stop before the warn- Diesel engines are fitted with an injec- ing light goes out. tion pump with an electronic regulator As a guide, this type of cleaning should which prevents overrevving of the take up to 20 minutes.
ADVICE: antipollution, fuel economy and driving (1/3) Maintenance Engine adjustments Your vehicle complies with criteria for recycling and recovering vehicles at the It should be noted that failure to respect – Ignition: this does not require ad- end of their service life which will come antipollution regulations may lead to justment.
Page 79
ADVICE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring – Avoid sudden acceleration. – Brake as little as possible. If you an- system ticipate an obstacle or bend in ad- The exhaust gas monitoring system will vance, you may then simply release detect any operating faults in the vehi- the accelerator pedal.
Page 80
ADVICE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in city conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
This commitment is illustrated by the less fuel (eg. 140 g/km, equivalent to the vehicle components have been de- Renault eco² group signature. 5.3 l/100 km for a diesel vehicle). signed to enable them to be recycled. Our vehicles are also equipped with a...
DRIVING CORRECTION DEVICES (1/3) ABS (Anti-lock Braking Depending on the vehicle, this is com- Operating faults: posed of: System) – If the warning light on the in- – ABS (anti-lock braking system); strument panel comes on while driv- Under heavy braking, the ABS prevents –...
DRIVING CORRECTION DEVICES (2/3) Electronic stability program Operating faults Understeer control (ESP) with understeer control This system optimises the action of the When the system detects an operat- and traction control (ASR) ESP in the case of pronounced unders- ing fault the message “Check ESP” and teering (loss of front axle road holding).
DRIVING CORRECTION DEVICES (3/3) The traction control (ASR) offers ad- Hazard warning lights switching on ditional safety, it is recommended that Depending on the vehicle, these may you do not drive with the function disa- light up in the event of sudden decel- bled.
Page 85
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) The speed limiter function helps you Controls Switching on stay within the driving speed limit that 1 Main “On/Off” switch. Press switch 1 on the side showing you choose, known as the limit speed. .
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by re- It is possible to exceed the limit speed peatedly pressing: at any moment. To do this: press the accelerator pedal firmly and fully –...
Page 87
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been stored, it can be re- called by pressing switch 5 (R). Putting the function on Switching off the function standby The speed limiter function is interrupted when you press switch 1.
Page 88
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. Therefore, it can under no circum- The cruise control function helps you to Controls stances replace the driver’s respon- maintain your driving speed at a speed 1 Main “On/Off”...
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Switching on Activating cruise control Driving At a steady speed (above 20 mph Once a cruising speed is memorised Press switch 1 on the side showing (30 km/h) approximately) press switch and the cruise control function is active, Indicator light 6 comes on, lit green, 2 (+) or 3 (-): the function is activated you may lift your foot off the accelera-...
Page 90
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
Page 91
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Recalling the cruising speed If a speed has been stored, it is possi- ble to recall it by pressing button 5 (R), on condition that you are driving faster than 20 mph (30 km/h) and that you are sure that the road conditions are suit- able (traffic, road surface condition, weather conditions, etc.).
PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic sensors, fitted in the vehi- cle’s rear bumper, measure the dis- tance between the vehicle and an ob- stacle when reversing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when This function is an addi- the vehicle is approximately 25 centi-...
Page 93
PARKING DISTANCE CONTROL (2/2) Prolonged deactivation of the Operating faults system When the system detects an operating fault there will be a 3-second continu- You can deactivate the system perma- ous beep as a warning. Consult an ap- nently by pressing and holding switch 1. proved Dealer.
AIR VENTS: air outlets (1/2) 1 Demister outlets, side windows. 4 Centre air vents. 2 Side air vents. 5 Control panel. 3 Demisting outlets for the windscreen. 6 Footwell air vents.
AIR VENTS: air outlets (2/2) To remove bad odours from your ve- hicles, only use the systems designed for this purpose. Consult an approved Dealer. Centre air vents Side air vents Settings Settings Air flow: Air flow: Move control knob 7 (beyond the point Move control knob 10 (beyond the point of resistance).
HEATING/AIR CONDITIONING (1/3) Switching air conditioning on or off The air conditioning is switched on (in- dicator light illuminated) or off (indicator light extinguished) using button 6. The air conditioning system is used for: – lowering the temperature inside the passenger compartment;...
Page 99
HEATING/AIR CONDITIONING (2/3) The air flow is directed mainly ó towards the footwells. The air flow is directed to all air vents and the footwells. This is the recommended position for the best temperature in hot weather. The air flow is directed mainly to the dashboard vents.
Page 100
HEATING/AIR CONDITIONING (3/3) Adjusting the ventilation speed Normal use Turn control 3 to one of the four posi- tions to start the ventilation system and adjust the power. Select position 1 for minimum ventila- tion and position 4 for maximum ven- tilation.
AUTOMATIC CLIMATE CONTROL (1/8) Controls 8 and 10 - Adjusting the ventilation speed. (depending on vehicle) 11 - Heated rear screen and heated 1 – Clear View button to demist and door mirror de-icing. de-ice the windows. 12 - Air recirculation control. 2 - Switching off air conditioning.
AUTOMATIC CLIMATE CONTROL (2/8) Only the temperature and the AUTO symbol are displayed Functions managed in automatic mode are not displayed. – press button 6 to increase the tem- perature; – press button 3 to decrease the tem- perature. Note: The maximum and minimum settings of 15°C and 27°C allow the system to produce a minimum or maxi- mum temperature, whatever the ambi-...
Page 103
AUTOMATIC CLIMATE CONTROL (3/8) Adjusting automatic mode The system normally operates in auto- matic mode but you can alter the stand- ard settings used by the system (air distribution, etc.). These options are explained on the following pages. The displayed temperature values show a comfort level.
Page 104
AUTOMATIC CLIMATE CONTROL (4/8) The air flow is directed mainly ô to the dashboard air vents. This position allows the passenger compartment to be heated or cooled more quickly. The air flow is directed to all ö the windscreen demisting vents and the passenger footwells.
Page 105
AUTOMATIC CLIMATE CONTROL (5/8) Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. Automatic mode is switched off by pressing buttons 8 and 10. These buttons allow you to increase or decrease ventilation speed.
Page 106
AUTOMATIC CLIMATE CONTROL (6/8) Rear screen de-icing/ To exit this function, press button 11 again. Demisting automatically stops demisting by default. Press button 11. This function allows rapid electric de- misting of the rear screen and, depend- ing on the vehicle, electric de-icing of the door mirrors.
Page 107
AUTOMATIC CLIMATE CONTROL (7/8) Note: if you wish to reduce the air flow (which may produce a certain amount of noise in the passenger compart- ment), press button 10. To exit this function, press: – button 1 again; – or button 5 (the AUTO indicator light on the display will light up).
AUTOMATIC CLIMATE CONTROL (8/8) Air recirculation Prolonged use of the air recirculation mode may cause the windows to mist Pressing button 12 activates air recir- up or lead to odours, as the air is not culation (the symbol lights up on the renewed.
AIR CONDITIONING: information and advice on use Operating faults Fuel consumption As a general rule, contact your ap- You will normally notice an increase proved Dealer in the event of an op- in fuel consumption (especially erating fault. when driving in town) when the air –...
INTERIOR LIGHTING Special features Remote unlocking of the doors trig- gers timed lighting of the passenger compartment. If one of the front or rear doors is opened, the timed lighting will start again. Then the courtesy light and the luggage compartment light dim and go out.
SUN VISOR/MIRROR Sun visor Courtesy mirror 2 (passenger side) Lower sun visor 1. If the sun visor is fitted with a courtesy The clip can be used to hold motorway mirror, it has a cover. passes, etc.. When driving, ensure the courtesy mirror cover is closed.
ELECTRIC WINDOWS (1/2) One-touch electric windows The one-touch mode works in addition to the operation of the electric windows described previously. It is fitted to the driver’s window and is used for low- ering only. Briefly press switch 1: the window lowers completely.
Page 113
ELECTRIC WINDOWS (2/2) Rear screen window winder 4 using the remote control – Press switch 4 to open the rear Pressing button 5 briefly completely screen A. The permissible load on the tailgate lowers or raises the rear screen. with the window lowered is 50 kg. –...
MANUAL SUNROOF Precautions during use – check that the sunroof is properly closed before leaving your vehicle; – clean the seal every three months using branded products rec- ommended Technical Department; – do not open the sunroof immedi- ately after the vehicle has been in the rain or after your car has been washed.
Page 115
SLIDING REAR SUNROOF Opening Note: when driving with the roof open, Closing air noise may be heard. To reduce this, Unlock controls 2; the rear sunroof Unlock controls 2, the sliding rear sun- open the manual sunroofs fully (refer to opens automatically (ensure that there roof closes automatically;...
ASHTRAYS/CIGAR LIGHTER/ACCESSORIES SOCKETS Removable ashtray 1 Accessories sockets C o n n e c t a c c e s s o r i e s This is a removable ashtray which can You may use cigar lighter recess 2 or with a maximum power of be placed in the cup holders 4.
PASSENGER COMPARTMENT STORAGE/FITTINGS (1/2) Storage compartment Central storage compartment 3 To open it, lift handle 1. To open it, lift cover 4. It will store a 1.5 litre bottle. Multimedia sockets 2 Ensure that no hard, heavy or pointed objects are placed in the “open”...
Page 118
PASSENGER COMPARTMENT STORAGE/FITTINGS (2/2) Front door storage Rear storage compartments 7 Clip 9 compartments 5 and 8 This can be used for storing motorway tickets, cards, etc. Bottle holder 6 Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passen- gers during sudden turning, braking...
REAR HEADRESTS To raise it Storage position 2 Child’s convertible headrest Slide it to the required height. Pull it towards you and lower it com- If fitted to the vehicle, the child head- pletely. rest and booster cushion can only be To lower it When the headrest is fully lowered, it installed on the rear side seats.
ADJUSTING THE REAR SEATS The rear seats are separate seats. To adjust the angle of the To fold down a seatback seatback (table position) To move the seats forwards – Lift the handle 3. Lower the headrest 2 or backwards –...
REAR SEAT FUNCTIONS (1/2) To remove a seat – Lower the headrest; – unfasten the seat belt buckle(s); – fold down the seatback; – move the seat backwards as far as it will go; – operate the handle 1 and lift the seat until it locks in the vertical position.
Page 122
REAR SEAT FUNCTIONS (2/2) To fit a seat Fit the feet 5 in their anchorage points: Press to lock in place. Check that they are correctly locked. Unlock the catch 2, then lower the seat to approximately ten centimetres from the floor and release it: the seat will po- sition itself under its own weight.
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Always position the objects trans- ported so that the largest surface is against: – the rear seatbacks, for normal loads; – the rear seats (folded down), for bulky loads; Always position the heavi- est items directly on the floor.
LUGGAGE NET This is located in the luggage compart- Positioning the luggage net 2 ment, in a special cover. – Upper section: insert the tabs at the It may be attached behind the front ends of the net in hooks 1; Luggage compartment an- seats or behind the rear seats.
BONNET (1/2) To open, pull handle 1, located on the Unlocking the bonnet catch Opening the bonnet left-hand side of the dashboard. Lift the bonnet by several centimetres Lift the bonnet up and release stay 4 and push lever 2 to the left. from its holder 5.
BONNET (2/2) Closing the bonnet Check that nothing has been left in the After carrying out any work engine compartment. in the engine compart- Place stay 4 back into its holders 5, ment, check that nothing hold the bonnet in the middle and lower has been left behind (cloth, it to 20 cm above the closed position, tools, etc.).
ENGINE OIL LEVEL: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes. However, contact an approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period.
Page 129
ENGINE OIL LEVEL: general information (2/2) Maximum engine oil level exceeded. The oil level should only be read with the dipstick as explained above. If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer. Reading the level using the dipstick –...
ENGINE OIL LEVEL: topping up/filling (1/2) In order to prevent splashback, it is recommended that a funnel be used when topping up/filling with oil Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and the ground and the engine should be cold...
Page 131
ENGINE OIL LEVEL: topping up/filling /OIL CHANGE (2/2) Oil change Filling: take care when Service interval: refer topping up the oil that Maintenance Service Booklet for your no oil drips onto engine vehicle. components - risk of fire. Remember to refit the cap securely Average capacities for oil change as there is a risk of fire if oil splashes including oil filter...
LEVELS (1/3) Level 1 Topping up It is normal for the level to drop as the After any operation on the hydraulic cir- brake shoes become worn, but it must cuit, a specialist must replace the fluid. never drop lower than the “MINI” warn- Only use fluids approved by our ing line.
Page 133
LEVELS (2/3) Checking intervals Replacement intervals Check the coolant level regularly Refer to the Maintenance Service (very severe damage is likely to be Booklet for your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
LEVELS /FILTERS (3/3) Filters Liquid Screen wash product (product with an- The replacement of filter elements (air tifreeze in winter). filter, passenger compartment filter, diesel filter, etc.) is scheduled in the Jets maintenance operations for your vehi- cle. To adjust the height of the windscreen washer jets, use a tool such as a flatb- Replacement intervals for filter el- lade screwdriver.
BATTERY Depending on the vehicle, a system continuously checks the battery charge status. With the ignition off, in order to save the battery, some electrical consum- ers may be switched off (dipped beam headlights, 12 V sockets, interior light- ing, radio, ventilation, etc.) On the instrument panel, depending on the vehicle, this cut-off is accompanied by the message “battery saving mode”...
Page 136
TYRE PRESSURE WHEN cold Tyre dimensions This is specific to the vehicle: – 205/60 R 16 96 T. Refer to Section 5 “Tyres” for informa- tion on changing tyres. The tyre pressure is indicated on Zone D: tyre pressures for the front label A affixed to the edge of the driv- wheels (motorway) or when driving with Tyre safety and use of snow...
BODYWORK MAINTENANCE (1/2) A well-maintained vehicle will last – minor impacts – Allow rust to form following minor im- longer. It is therefore recommended to pacts. You should take a minimum number of maintain the exterior of the vehicle reg- precautions in order to safeguard your –...
Page 138
BODYWORK MAINTENANCE (2/2) You should – Wash your car frequently, with the – Before going through a roller type car engine off, with cleaning products wash, return the windscreen wiper – Observe the vehicle stopping dis- recommended by our Technical stalk to the Park position (refer to tances when driving on gravelled Department (never use abrasive...
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
Page 140
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
PUNCTURE/EMERGENCY SPARE WHEEL To access the emergency spare wheel – Open the tailgate; – undo the nut with wheelbrace 1; – detach cage 3; – remove the emergency spare wheel. To store the wheel in the cage – Make sure the wheel is correctly po- sitioned in the cage, valve facing down;...
TOOL KIT To reposition the tool kit, position tool kit pin 4 into housing 3. Make sure the kit is correctly positioned so as to be able to tighten wheel 2. Close the flap again. The tool kit includes: Retaining belt (depending on vehicle) After use, reposition the strap making sure that it retains all components in the tool kit.
CHANGING A WHEEL (1/2) Continue tightening to position the baseplate on the ground correctly. Turn handle 3 on the jack to lift the wheel off the ground. If the vehicle is parked on the hard shoulder, you must warn other road users of Use the wheelbrace to slacken off the your vehicle’s presence wheel bolts 2.
Page 145
CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. For vehicles fitted with alloy wheel rims, use the guide bolt located in the tool kit to finish loosening and start tightening the bolts. For more information on this tool, refer to Section 5 “Tool kit”.
TYRES (1/3) Tyre and wheel safety When the tyre tread has been eroded to the level of the warning strips, they The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.
TYRES (2/3) Tyre pressures Fitting new tyres Pressures should be checked when the tyres are cold; ignore higher pressures Respect the tyre pressures (including which may be reached in hot weather the emergency spare wheel). Check or following a fast journey. them at least once a month and before For safety reasons, this op- a long journey (refer to the label on the...
Page 148
TYRES (3/3) Changing wheels around Use in winter This practice is not recommended. Chains In all cases, we would recommend that you contact an approved dealer For safety reasons, fitting snow who will be able to advise you on chains to the rear axle is strictly for- the choice of equipment which is bidden.
LIGHTS: changing bulbs (1/2) Dipped beam/main beam Do not touch the bulb glass. Hold it by its base. To comply with local legislation, or headlights as a precaution, you can obtain an To refit it, carry out the above opera- –...
Page 150
LIGHTS: changing bulbs (2/2) Cleaning the headlights As the headlights are made of plastic glass, use a soft cloth or cotton wool to clean them. If this does not clean it properly, moisten the cloth with soapy water, then wipe clean with a soft damp cloth or cotton wool.
FOG LIGHTS: changing bulbs Additional lights If you wish to fit your vehicle with fog lights or long range headlights, consult an approved Dealer. The bulbs are under pres- sure and can break when replaced. Front fog lights 1 Rear fog lights 2 Risk of injury.
REAR LIGHTS: changing bulbs (1/2) Rear lights – unscrew the screws 3 and remove – unscrew the screws 5; cover 4; – unclip the lower section, then the – Open the hinged door; upper section of the light by pulling it –...
Page 153
REAR LIGHTS: changing bulbs (2/2) – Pull the tabs 6 to unclip the bulb Type of bulb: High-level brake light 11 holders 7; 8 Indicator Consult an approved dealer. – replace the bulb, then proceed in the Pear-shaped, bayonet type bulb reverse order to refit the bulb;...
INDICATOR LIGHTS: changing bulbs Unclip indicator light 1 on the door side, Bulb type: WY5W. using a flat-blade screwdriver type tool. Replace the bulb and refit the indicator Turn the bulb holder a quarter of a turn light. and take out the bulb. 5.14...
INTERIOR LIGHTING: changing bulbs Passenger compartment Pull bulbs 2 and 3 downwards to remove them from their housings. lights Remove lens 1 using a tool such as a Bulb type 2: W6W flat-blade screwdriver. Bulb type 3: W5W Replace the bulbs and replace the lens. 5.15...
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: – Ensure that any consumers (cour- tesy lights, etc.) are switched off before disconnecting or reconnect- ing the battery; – when charging, stop the charger before connecting or disconnecting the battery; –...
BATTERY: troubleshooting (2/2) Starting the vehicle using the Connect the positive (+) lead A to (+) terminal 1 of the discharged battery, battery from another vehicle then to (+) terminal 2 of the battery sup- If you have to use the battery from an- plying the current.
FUSES (1/2) Unclip cover 1. To identify the fuses, refer to the fuse allocation label (shown on the following page). It is not advisable to use the free fuse locations. Fuse box Remove the fuse with pliers 2 (depend- ing on vehicle). If any electrical component does not To remove the fuse from the tweez- work, check the condition of the fuses.
Page 159
FUSES (2/2) Allocation of fuses (DEPENDING ON THE EQUIPMENT LEVEL) Some functions are protected by fuses Symbol Allocation Symbol Allocation located in the engine compartment. However, because of their reduced ac- cessibility, you are advised to have Interior lighting, electric Radio, display, heat-...
WIPER BLADES Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...
TOWING: breakdown Only use the front and rear towing points (never use the driveshafts). These towing points may only be used for towing: never use them for lifting the vehicle directly or indirectly. Do not leave the tools unse- cured inside the vehicle as they may come loose under braking.
TOWING: equipment A = 776.5 mm. Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to Section 6 “Weights”. Refer to the manufacturer’s instruc- tions for information on how to fit and operate the towing equipment. Please keep these instructions with the rest of the vehicle documenta- tion.
FITTING A RADIO (1/2) Radio equipment Tweeter speakers 4 Bass speakers 5 Unclip the blanking cover. The connec- tions for the aerial, + and – supply, and speaker wires are found behind the cover. The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle version: 1 offset display (time, exterior temper-...
Page 164
FITTING A RADIO (2/2) Rear speakers 6 – In all cases, it is very important to follow the manufacturer’s instructions care- fully. – The specifications of the brackets and wires vary depending on the equipment level of your vehicle and the type of radio. Consult an approved Dealer to find out the correct part number.
ACCESSORIES Before fitting an electrical or electronic device (particu- larly for transmitters/receiv- ers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle. Contact an approved dealer for this information. Electrical and electronic accessories Use of transmission/ –...
RADIO FREQUENCY REMOTE CONTROL: batteries Replacing the remote control Note: It is not advisable to touch the electronic circuit in the key cover when battery replacing the battery. Undo screw 1 to remove the remote control cover. Replace battery 2 according to the di- rection marked on the cover.
DIESEL FILTER Repriming the fuel circuit If the vehicle runs out of fuel completely, it is necessary to actuate the manual priming bulb after having refilled. Vehicles with manual priming pump The peripheral components (alter- – If fitted to the vehicle, turn the bleed nator, starter, engine mountings, screw located on the diesel filter.
OPERATING FAULTS (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO Warning lights dim or fail to come on; Battery terminals disconnected, Retighten, reconnect or clean them if they the starter does not run.
Page 169
OPERATING FAULTS (2/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to the correct pres- Check the tyre pressures: if this is not the sure, incorrectly balanced or dam- problem, have them checked by an ap- aged.
Page 170
OPERATING FAULTS (3/5) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved Dealer. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and ant temperature indicator and the contact an approved Dealer.
Page 171
OPERATING FAULTS (4/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved Dealer. The wiper does not stop. Faulty electrical controls. Consult an approved Dealer.
Page 172
OPERATING FAULTS (5/5) Rear door and sliding rear POSSIBLE CAUSES WHAT TO DO sunroof Rear door cannot be opened. The rear screen cannot be lowered Consult an approved dealer. using the opening control. The window is open but the door re- Wait a few minutes, then retry.
VEHICLE IDENTIFICATION PLATES The information shown on the ve- 6 Technical specifications of vehicle. hicle identification plate should be 7 Vehicle paint reference. quoted on all correspondence or 8 Equipment level. orders. 9 Vehicle type. 10 Trim code. Vehicle identification plate A 11 Additional equipment specifica- 1 Vehicle type and chassis number.
ENGINE IDENTIFICATION PLATES The information on the engine plate or label A should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
ENGINE SPECIFICATIONS Versions 1.6 16V 1.5 dCi Engine type (see engine plate) Cubic capacity (cc) 1 598 1 461 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap. If not available, for a limited time only, use unleaded fuel: Diesel Type of fuel...
WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact an approved Dealer. Maximum Permissible All-Up Weight (MMAC) Weights are indicated on the vehicle identification plate (refer to Gross Train Weight (MTR) the information on “Vehicle identification plates”...
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 181
SERVICE SHEETS (2/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 182
SERVICE SHEETS (3/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 183
SERVICE SHEETS (4/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 184
SERVICE SHEETS (5/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 185
SERVICE SHEETS (6/6) VIN: .................. Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.14...
Page 187
ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
Page 188
ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
Page 189
ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 190
ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 193
............3.30 remote control door locking batteries ............... 5.26 remote control electric door locking ......1.2, 1.4 maintenance: RENAULT ANTI-INTRUDER DEVICE (RAID) ..... 1.9 bodywork ............4.13 – 4.14 replacement parts ..............6.7 interior trim ............4.15 – 4.16...