1. Manuals
  2. Brands
  3. Renault Manuals
  4. Automobile
  5. KANGOO Z.E.
  6. Driver's handbook manual

Renault KANGOO Z.E Driver's Handbook Manual

Hide thumbs Also See for KANGOO Z.E:
Table of Contents

Advertisement

Quick Links

See also: User Manual
KANGOO
KANGOO
Z.E.
Z.E.
DRIVER'S HANDBOOK
DRIVER'S HANDBOOK

Advertisement

Table of Contents
loading

Related Manuals for Renault KANGOO Z.E

Summary of Contents for Renault KANGOO Z.E

  • Page 1 KANGOO KANGOO Z.E. Z.E. DRIVER’S HANDBOOK DRIVER’S HANDBOOK...

  • Page 3: Driving

    This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.

  • Page 5: Table Of Contents

    Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
  • Page 7 Section 1: Getting to know your vehicle Electric vehicle: introduction ............Important recommendations .

  • Page 8: Electric Vehicle: Introduction

    ELECTRIC VEHICLE: introduction (1/5) 1 Electric motor 2 Fuel filler flap for additional heating 3 Traction battery 4 Orange electrical power cables 5 Secondary 12V battery 6 Electric charging connection...
  • Page 9 ELECTRIC VEHICLE: introduction (2/5) Electric vehicles have special features, but operate in a similar manner to con- ventional vehicles. The main difference in electric vehicles is the exclusive use of electric energy instead of fuel, as used in conventional vehicles. We therefore recommend that you read these instructions describing your elec- tric vehicle carefully.
  • Page 10 ELECTRIC VEHICLE: introduction (3/5) Batteries Traction battery 12 volt battery This battery stores the energy neces- The second battery on your vehicle is Your electric vehicle has two types of sary to operate the motor in your elec- a 12V battery, similar to those used battery: tric vehicle properly.
  • Page 11 ELECTRIC VEHICLE: introduction (4/5) The vehicle drive system in an electric vehicle uses an alternating voltage of ap- proximately 400 volts. This system can get hot during and after switching off the ignition. Respect warning messages given on the The A symbol identifies the electrical 400 volt electrical circuit labels in the vehicle.
  • Page 12 ELECTRIC VEHICLE: introduction (5/5) Driving Noise Bad weather, flooded roads: Electric vehicles are particularly quiet. As with a car with an automatic gear- Do not drive through You will not yet necessarily be used to box, you will have to get used to not floods if the depth of water it, and neither will other road users.

  • Page 13: Important Recommendations

    IMPORTANT RECOMMENDATIONS Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious injury or electric shock which may present a risk to life. In the event of an accident or impact In the event of an accident or an impact to the underside of the vehicle (e.g.: striking a post, raised kerb or other street furni- ture), this may damage the electric circuit or the traction battery.

  • Page 14: Electric Vehicle: Charging

    ELECTRIC VEHICLE: charging (1/7) Charging diagram 1 Specific wall socket or recharging ter- minal If you have any questions regarding the equipment needed for charging, 2 Electric charging connection please ask an authorised dealer. 3 Charging cord...
  • Page 15 ELECTRIC VEHICLE: charging (2/7) Important recommendations for charging your vehicle Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious injury or electric shocks which could result in death. Charging Do not do anything to the vehicle during charging (washing, working in the engine compartment, etc.). In the event of the presence of water, signs of corrosion or foreign bodies in the charging cord connector or in the vehicle charg- ing socket, do not charge the vehicle.
  • Page 16 ELECTRIC VEHICLE: charging (3/7) Charging cord A Charging cord B Always read the charging cord instruc- tions carefully before using it B. This cord, designed for specific wall This cord allows: sockets or public terminals, enables the – standard charge, on a socket used standard charge of the traction battery.
  • Page 17 ELECTRIC VEHICLE: charging (4/7) Important recommendations for charging your vehicle Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious injury or electric shocks which could result in death. Choice of charging cord The standard charging cords supplied with the vehicle have been designed specifically for this vehicle.
  • Page 18 ELECTRIC VEHICLE: charging (5/7) Avoid charging and parking your vehi- Recommendations cle in extreme temperatures (hot or – In extreme heat, favour parking and cold). recharging the vehicle in a shaded/ covered location. When the vehicle is parked in tempera- –...
  • Page 19 ELECTRIC VEHICLE: charging (6/7) Recharging the traction – open the charging flap 6; The charging cord is automatically – open the valve 7; locked with the vehicle. This will make it battery – grab the handle 8; impossible to unplug the cord from your With the ignition off, lever 5 in gear P –...
  • Page 20 ELECTRIC VEHICLE: charging (7/7) Precautions to take when removing – unplug the charging cord from the Note: from the socket vehicle. Warning light goes out Immediately after a long charge of the on the instrument panel; – Press the button 9 on the radio fre- traction battery, the cord may be hot.

  • Page 21: Key, Radio Frequency Remote Control: General Information, Use

    KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Radio frequency remote control unit 1 Locking all the opening elements. 2 Unlocking all opening elements and Driver’s responsibility the charging cord. Never leave your vehicle 3 Coded key for ignition switch, driv- Advice with the card inside the er’s door and fuel filler cap.
  • Page 22 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surround- ings: take care not to lock or unlock the doors by inadvertently pressing the but- tons on the remote control. For replacement, or if you require an additional remote Interference...

  • Page 23: Locking The Doors

    RADIO FREQUENCY REMOTE CONTROL/KEY: use The doors are locked and unlocked using the remote control unit. It is powered by a battery which must be replaced (refer to the information on the “Key, radio frequency remote con- trol: batteries” in Section 5). The key must not be used for any function other than those described in the handbook (removing the cap...

  • Page 24: Doors

    DOORS (1/5) Opening from the outside Lights-on reminder buzzer Child safety (depending on vehicle) Unlock the door and pull handle 1. For If you have left the lights on after switch- information on unlocking the doors, ing off the ignition, a reminder buzzer At the rear, to prevent the side door refer to the information on the “Key, will sound when a door is opened (to...

  • Page 25: Sliding Side Door

    DOORS (2/5) Recommendations con- cerning the sliding side door The following precautions must be taken when opening and closing the doors or any other open- ing element: – Check that the door will not come into contact with any person, animal or object.
  • Page 26 DOORS (3/5) Rear hinged doors Opening the doors to the maximum position Opening from the outside For each door, pull handle 8 to release Unlock the door and pull handle 7. For the door check strap. Open the door as information on unlocking the doors, far as possible.
  • Page 27 DOORS (4/5) Rear hinged doors (continued) Opening from the inside (depending on vehicle) Pull handle 10 and open the door. Pull Driver’s responsibility when parking or stopping the vehicle lever 9 to open the small door. Never leave an animal, child or adult who is not self-sufficient alone on Closing from the inside your vehicle, even for a short time.
  • Page 28 DOORS (5/5) Tailgate Closing Lower the tailgate using interior han- Opening dles 12. Unlock the door and pull handle 11. When the tailgate reaches shoulder For information on unlocking the doors, height, gently push it shut. refer to the information on the “Key, Opening manually from the inside radio frequency remote control: use”...

  • Page 29: Indicator Light

    CENTRAL DOOR LOCKING/UNLOCKING (1/2) Locking the opening elements without the remote control With the engine and ignition off, the sliding side doors closed and a front door open, press switch 1 for more than five seconds. Make sure you have your key with you before you leave your vehicle.

  • Page 30: Manual Control

    CENTRAL DOOR LOCKING/UNLOCKING (2/2) Manual control The doors may then only be opened from inside the vehicle or with the key Using the key for the front doors. Lock or unlock the driver’s door by in- Sliding side door (fuel filler cap serting the key 3 fully into lock 2, and side) turning the key.

  • Page 31: Operating Principle

    AUTOMATIC LOCKING WHEN DRIVING (RAID) Operating principle When the engine is started, the system automatically locks the doors when the vehicle reaches a speed of approxi- mately 4 mph (7 km/h). Operating faults If you notice an operating fault (auto- matic locking impossible), first check that all doors are correctly locked.
  • Page 32 FRONT HEADRESTS (1/3) To refit the headrest First, check that the headrest rods are clean and correctly aligned. Pull the tab 2 forwards. Insert the headrest rods in the holes, with the notches facing forwards (tilt the seat backwards if necessary). Guide the headrest down to the desired height.
  • Page 33 FRONT HEADRESTS (2/3) To remove the headrest Raise it to its highest position. Press button 4 and lift the headrest to release Note: when the headrest is removed, take care not to change the positions of the rods. To refit the headrest If the setting of the rods has been al- tered, pull them fully upwards.
  • Page 34 FRONT HEADRESTS (3/3) To refit the headrest Press tab 5. Insert the headrest rods in the holes with the notches facing forward, and guide the headrest down to the re- quired height. Headrest C To raise the headrest Pull it upwards to the required height. To lower the headrest Press tab 5 and guide the headrest down to the desired height.

  • Page 35: Headrests/Front Seats

    FRONT SEATS (1/2) To move forwards or To tilt the seatback ð Heated seats backwards Depending on the seat, lower or lift With the engine running, activate lever 2 and tilt the seatback until it Depending on the seat, lift bar 1 or switch 5;...

  • Page 36: Front Seats

    FRONT SEATS (2/2) Front seats Operating faults For safety reasons, carry (depending on vehicle) out any adjustments when the vehicle is not being If the sliding side door does not work, driven. lower handle 6, hold it while the seat- back tilts and slide the seat forwards.

  • Page 37: Roof Flap

    ROOF FLAP (1/2) Note: When driving with the roof flap open, you may hear wind noise. To reduce these, open one of the side win- dows slightly. To open: Transverse bar – Unlock the control 2, the roof flap lifts When loading bulky objects, the trans- Driving with the roof flap automatically (make sure that noth-...
  • Page 38 ROOF FLAP (2/2) To close: – Unlock the control 2, the roof flap au- tomatically opens halfway; – pull the handle 1 and lock the roof flap in the closed position. Before starting, always reposition the transverse bar and ensure it is correctly locked.

  • Page 39: Swivelling Partition

    SWIVELLING PARTITION To rotate the partition – unlock the swivelling section by lift- – Pivot the moving section 90 degrees, ing catch 3; lock it at point 5 and lower catch 3. – Unlock the seat base by moving – reposition the seat base, proceeding Note: before refitting the swivelling handle 1 downwards;...

  • Page 40: Seat Belts

    SEAT BELTS (1/4) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
  • Page 41 SEAT BELTS (2/4) Front seat belt reminder ™ warning light It remains on when the engine is started if your seat belt is not fas- tened. When the vehicle reaches a speed of 12 mph (20 km/h), the warn- ing light flashes and a buzzer sounds. Then, the beep sounds at a low volume for 30 seconds, then at a high volume for 90 seconds.
  • Page 42 SEAT BELTS (3/4) Rear side seat belts Unwind the belt slowly and smoothly and ensure that buckle 8 locks into catch 9 (check that it is locked by pull- ing on buckle 8). The belts are adjusted in the same way as the front seat belts.
  • Page 43 SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...

  • Page 44: Methods Of Restraint In Addition To The Front Seat Belts

    METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/3) Depending on the vehicle, they will con- – Have the entire restraint sist of: system checked following – seat belt pretensioners; an accident. – front airbags 1 for driver and –...
  • Page 45 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/3) Airbag for driver and front Operation passenger This system is only operational when the ignition is switched on. It is fitted to the front seats on the driv- er’s side and, depending on the vehicle, In a severe frontal impact, the air bags on the passenger’s side as well.
  • Page 46 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/3) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...

  • Page 47: Side Protection Devices

    SIDE PROTECTION DEVICES Side air bags (depending on vehicle) This air bag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact.

  • Page 48: Additional Methods Of Restraint

    ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.

  • Page 49: Steering Wheel/Power-Assisted Steering

    STEERING WHEEL/POWER-ASSISTED STEERING Power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).

  • Page 50: Child Safety: General Information

    CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
  • Page 51 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
  • Page 52 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
  • Page 53 CHILD SAFETY: choosing a child/baby seat mounting (1/2) The are two ways of attaching child Attachment with the ISOFIX system Do not use the child seat seats: via the seat belt or using the Authorised ISOFIX child seats are ap- if it may unfasten the seat ISOFIX system.
  • Page 54 CHILD SAFETY: choosing a child/baby seat mounting (2/2) The two rings 1 are located between Depending on the vehicle, pass the the seatback and the seat base, behind strap between wheel arch liner 4 and The ISOFIX anchorage the zip fasteners, and are identified by the underside of upper partition 5.

  • Page 55: Fitting A Child Seat

    CHILD SAFETY: fitting a child seat (1/5) Some seats are not suitable for fitting In the front seat In the rear seat child seats. The diagrams on the fol- The laws concerning children travel- A carrycot can be installed across the lowing pages show you how to attach ling in the front passenger seat differ in vehicle and will take up at least two...
  • Page 56 CHILD SAFETY: fitting a child seat (2/5) 2-seat version Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt. ² Seat not suitable for fitting child seats. ³...
  • Page 57 CHILD SAFETY: fitting a child seat (3/5) 5-seat version Child seats attached using the ISOFIX mounting ü Seat which allows an ISOFIX. child seat to be fitted. ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat.
  • Page 58 CHILD SAFETY: fitting a child seat (4/5) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. 5-seat version Seat size Weight of Front passenger Rear side seats Rear centre seat the child seat (1) (2)
  • Page 59 CHILD SAFETY: fitting a child seat (5/5) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal”...

  • Page 60: Deactivating/Activating The Front Passenger Airbag

    CHILD SAFETY: deactivating/activating the front passenger airbag (1/3) DANGER Since front passenger airbag triggering and the position of a rear-facing child seat are incompatible, NEVER use a restraining device for rear- facing children on a seat with an ACTIVATED AIRBAG in front of it. This provides a risk of DEATH or SERIOUS INJURY to the CHILD.
  • Page 61 CHILD SAFETY: deactivating/activating the front passenger airbag (2/3) The markings on the dashboard and labels A on each side of the passen- ger sun visor 3 (for example, the labels shown above) will remind you of these instructions. DANGER Since front passenger airbag triggering and the...
  • Page 62 CHILD SAFETY: deactivating/activating the front passenger airbag (3/3) Activation of the front Operating faults passenger air bag In the event that the front passenger air bag activation/deactivation system is You should reactivate the air bag as faulty, child seats must not be fitted to soon as you remove the child seat from the front seat.

  • Page 63: Rear-View Mirrors

    REAR-VIEW MIRRORS Heated door mirrors When the engine is started, mirror de- icing is activated with the rear screen de-icing/demisting. Folding door mirrors Move button 2 to position D to fold the door mirrors in. To reset them for driv- ing, return to position B.

  • Page 64: Driving Position

    DRIVING POSITION, LEFT-HAND DRIVE (1/2) 1.58...
  • Page 65 DRIVING POSITION, LEFT-HAND DRIVER (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Stalk for: 9 Windscreen demister outlet. 21 Gear lever. – direction indicator lights; – exterior lights; 10 Location for passenger air bag. 22 Remote control/location for radio, –...
  • Page 66 DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 1.60...
  • Page 67 DRIVING POSITION: RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side window demister outlet. 10 – Horn. 20 Location for radio, navigation – Location for driver’s air bag. system. 2 Side air vent. 11 Instrument panel.

  • Page 68: Warning Lights

    WARNING LIGHTS (1/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Main beam headlight tell-tale 12V battery charge warning á Ú light light Dipped beam headlight tell- If it comes on when you are driving, it tale indicates that the circuit is overcharged or has discharged.
  • Page 69 WARNING LIGHTS (2/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Brake circuit fault warning Air bag warning light å light This comes on when the igni- If it comes on during braking and is ac- tion is switched on and goes out after ®...
  • Page 70 WARNING LIGHTS (3/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Electrotechnical system Low fuel level or additional warning light heating warning light When the blue warning light comes on, This comes on when the ignition is this indicates that the traction battery switched on and goes out after a few temperature is too low.

  • Page 71: Displays And Indicators

    DISPLAYS AND INDICATORS (1/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. Charge level 3 The gauge indicates the level of energy remaining. Reserve threshold 5 This indicates that the battery is at ap- proximately 12% charge.
  • Page 72 DISPLAYS AND INDICATORS (2/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. “Consumption” usage zone C The needle tells you the energy con- sumption (vehicle moving on a flat sur- face, for example).
  • Page 73 DISPLAYS AND INDICATORS (3/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. – Display selection Press briefly to move from the total mileage to the trip mileage and vice versa. –...
  • Page 74 TRIP COMPUTER: general information (1/2) a) Total mileage and trip mileage re- corder; b) journey parameters: – Total energy consumption since the last reset; – average energy consumption; – current energy consumption; – Total energy consumption since the vehicle first entered into serv- ice;...

  • Page 75: On-Board Computer

    TRIP COMPUTER: general information (2/2) Automatic resetting of the Interpreting some of the journey parameters values displayed after resetting Resetting occurs automatically when the maximum value of any of the pa- Average energy consumption and rameters is exceeded. speed are all the more stable and reli- able as the distance travelled from the last reset is great.
  • Page 76 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km a) Total mileage and trip mileage recorder. 112,4 km CONSUMPTION 20 kWh b) Journey parameters.
  • Page 77 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected RANGE Estimated range with remaining energy. 118 km DISTANCE 522 km Distance travelled since the last reset. AVERAGE Average speed since the last reset.
  • Page 78 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected c) Service interval. SERVICE IN Distance remaining until the next service (displayed in kilometres), then when the service nears, several scenarios are possible: –...
  • Page 79 TRIP COMPUTER AND WARNING SYSTEM: journey parameters (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected SPEED LIMITER 90 km/h e) Cruise control/speed limiter programmed speed. Refer to the information on the “Speed limiter” and “Cruise control” in Section 2.

  • Page 80: Information Messages

    TRIP COMPUTER AND WARNING SYSTEM: information messages Information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpretation of messages “CHARGE REMAIN 02:10”...
  • Page 81 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an approved Dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
  • Page 82 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages.

  • Page 83: Clock And Exterior Temperature

    CLOCK AND EXTERIOR TEMPERATURE Exterior temperature After two seconds, the hours and min- utes start flashing. On equipped vehicles, the exterior tem- Press and hold the bottom button to perature is displayed at A. If it is be- enter the hour setting mode. tween -3°C and +3°C, the °C charac- ters flash (signalling a risk of ice).

  • Page 84: Audible And Visual Signals

    AUDIBLE AND VISUAL SIGNALS Horn Hazard warning lights Direction indicators é Press one of points 2. Pressing switch 3 illuminates Move stalk 1 parallel to the steering all four direction indicators and the wheel and in the direction you are going side-mounted indicator lights simul- to turn.
  • Page 85 PEDESTRIAN HORN Warning noise selection Electric vehicles are particularly quiet. This system enables you to warn – Keep the switch 1 depressed. people of your presence – especially The various sounds will be played in pedestrians and cyclists. succession; The system is activated automatically –...

  • Page 86: External Lighting And Signals

    EXTERNAL LIGHTING AND SIGNALS (1/3) Dipped beam Main beam headlights á headlights With stalk 1 in dipped beam headlights Manual operation position, move the stalk towards you. Turn the end of stalk 1 until the symbol The indicator light on the instrument is opposite mark 2.
  • Page 87 EXTERNAL LIGHTING AND SIGNALS (2/3) “See-me-home lighting” function (depending on vehicle) This function (useful, for example, when opening a gate, garage, etc.) enables you to switch the dipped headlights on momentarily. With the ignition off and the headlights off, pull stalk 1 towards you: the dipped beam headlights come on for approxi- mately sixty seconds.

  • Page 88: Rear Fog Light

    EXTERNAL LIGHTING AND SIGNALS (3/3) Rear fog light The front fog lights and the side lights or dipped beam headlights must be on. Turn ring 5 on stalk 1 until the symbol is opposite mark 4, then release it. This indicator light on the instrument panel comes on.

  • Page 89: Headlight Beam Adjustment

    HEADLIGHT BEAM ADJUSTMENT (1/2) 50 m 100 m Control knob 1 is used to adjust the A Poor adjustment: the lights are set height of the headlight beams accord- too high and could dazzle other ing to the load. drivers. Turn the control knob downwards to lower the beam.
  • Page 90 HEADLIGHT BEAM ADJUSTMENT (2/2) When driving on the left in a left- hand drive vehicle (or vice versa), you must adjust your lights tempo- rarily during your stay. Temporary adjustment Open the bonnet and identify the mark- ing B next to one of the front headlight projectors.

  • Page 91: Windscreen Wiper

    FRONT WINDSCREEN WASHER/WIPER (1/2) Automatic wiper function (depending on vehicle) With the engine running, move stalk 1. A Park B Automatic wiper function When this position is selected, the system detects the presence of water on the windscreen and trig- gers wiping at a suitable wiping speed.
  • Page 92 FRONT WINDSCREEN WASHER/WIPER (2/2) Windscreen wiper In freezing or snowy weather, ensure they are not stuck to the windscreen With the ignition on, pull stalk 1 to- (including the central area located wards you. behind the interior rear-view mirror) A brief pull will trigger a single sweep and the rear screen before starting of the wipers, in addition to the wind- the wipers (risk of motor overheat-...
  • Page 93 REAR WINDSCREEN WASHER/WIPER Rear screen wash/wipe (depending on vehicle) Turn the end of stalk 1 to position the symbol opposite mark 2. When the stalk is released, it returns to the rear screen wiper position. Check the condition of the wiper blades.

  • Page 94: Additional Heating Tank

    ADDITIONAL HEATING TANK Fuel grade Fuel filling – Insert the nozzle so that the valve Use a high-grade fuel that complies is open and fully insert the nozzle with the legislation in force in each before engaging it in order to fill the country and which must conform to tank (risk of splash-back).
  • Page 95 Section 2: Driving (Advice on use relating to fuel economy and the environment) Starting, stopping the engine ............Gear control .

  • Page 96: Starting/Stopping The Engine

    STARTING/STOPPING THE ENGINE “On” position M Stopping the engine The ignition is switched on: With the engine running, turn the key back to the “Stop” position St. Warning light goes out. Start position D Starting the engine – Move lever 1 to position P only ; –...

  • Page 97: Gear Control

    GEAR CONTROL (1/2) Driving Put lever 1 in position D. Hill start For hill starts, especially after a maxi- mum traction battery charge and for the first few miles, we recommend using the handbrake. While driving, press the accelerator pedal to achieve the desired speed. Reverse Put lever 1 in position R.

  • Page 98: Handbrake

    GEAR CONTROL /HANDBRAKE (2/2) Parking the vehicle Handbrake When the vehicle is stopped, move the To release: lever to position P while keeping your Pull the lever 5 up slightly, press foot on the brake pedal: the gearbox is button 6 and then lower the lever to the in neutral and the drive wheels are me- floor.

  • Page 99: Vehicle Range: Recommendations

    VEHICLE RANGE: recommendations (1/2) The vehicle range is approved for a mixed NEDC cycle (New European Driving Cycle). In real usage, the range of an electric vehicle may vary depending on several factors over which you have partial con- trol, which may make a considerable difference to the vehicle range.

  • Page 100: Vehicle Loading

    VEHICLE RANGE: recommendations (2/2) Vehicle loading Avoid pointlessly overloading your ve- hicle. Heating levels Tyres The use of heating or air conditioning An under-inflated tyre increases energy reduces vehicle range. consumption. Comply with the speci- Before using the vehicle, opt for “pro- fied tyre pressures for your vehicle.

  • Page 101: Environment

    ENVIRONMENT Emissions Your vehicle has been designed with – At the end of the vehicle’s service respect for the environment in mind for life, it should be sent to approved Your vehicle has been designed to its entire service life: during production, centres to ensure that it is recycled.

  • Page 102: Charge Meter

    CHARGE METER The traction battery supplies the elec- Energy recovery features “Recommended trical energy required for the motor to consumption” usage zone C The motor generates a more significant move the vehicle. engine brake than a conventional vehi- Indicates “economical” energy con- When you lift your foot off the accelera- cle.

  • Page 103: Eco" Mode

    “ECO” MODE FUNCTION Disabling the function Press switch 1. Warning light 2 goes out on the instru- ment panel. This function enables vehicle range to While driving, it is possible to leave the be optimised by limiting engine per- ECO mode temporarily in order to im- formance.

  • Page 104: Driver Correction Devices And Aids

    DRIVER CORRECTION DEVICES AND AIDS (1/3) ABS (anti-lock braking Depending on the vehicle, this is com- Operating faults: posed of: system) – If the warning light on the in- – of the ABS (anti-lock braking Under heavy braking, the ABS prevents strument panel comes on while driv- system);...

  • Page 105: Electronic Stability Program

    DRIVER CORRECTION DEVICES AND AIDS (2/3) Electronic stability program Understeer control Operating faults ESC with understeer control This system optimises the action of the When the system detects an operating and traction control ESC in the case of pronounced under- fault the message “CHECK ESC”...

  • Page 106: Emergency Brake Assist

    DRIVER CORRECTION DEVICES AND AIDS (3/3) Emergency brake assist Hill start assistance This is an additional system to ABS This function assists the driver when which helps reduce vehicle stopping starting on hills. It prevents the vehicle distances. from rolling backwards, depending on The hill start assistance the slope, by automatically applying the system cannot completely...
  • Page 107 CRUISE CONTROL, SPEED LIMITER: speed limiter function (1/3) The speed limiter function helps you Controls Switching on stay within the driving speed limit that 1 Main “On/Off” switch. Press the side switch 1 . Warning you choose, known as the limit speed. light comes on, lit orange, and the 2 Speed limiter activation, memory...

  • Page 108: Speed Limiter

    CRUISE CONTROL, SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by re- It is possible to exceed the limit speed peatedly pressing: at any moment. To do this: press the accelerator pedal firmly and fully –...
  • Page 109 CRUISE CONTROL, SPEED LIMITER: speed limiter (3/3) Recalling the limit speed If a speed has been stored, it can be re- called by pressing switch 5 (R). Putting the function on Switching off the function standby The speed limiter function is deacti- vated when you press switch 1.
  • Page 110 CRUISE CONTROL, SPEED LIMITER: cruise control function (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. Therefore, it can under no circum- The cruise control function helps you to Controls stances replace the driver’s respon- maintain your driving speed at a speed...

  • Page 111: Cruise Control

    CRUISE CONTROL, SPEED LIMITER: cruise control function (2/4) Switching on Activating cruise control Driving At a steady speed (above 18 mph (30 Once a cruising speed is memorised Press switch 1 side km/h approximately)) press switch 2 and the cruise control function is active, Indicator light 6 comes on, lit green, and or (+): the function is activated and the you may lift your foot off the accelera-...
  • Page 112 CRUISE CONTROL, SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
  • Page 113 CRUISE CONTROL, SPEED LIMITER: cruise control function (4/4) Recalling the cruising speed If a speed has been stored, it can be re- called by pressing button 5 (R), on con- dition that you are driving faster than approximately 20 mph (30 km/h) and that you are sure that the driving condi- tions are suitable (traffic, road surface condition, weather conditions, etc.).

  • Page 114: Parking Distance Control

    PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the ve- hicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centi- metres from the obstacle.
  • Page 115 PARKING DISTANCE CONTROL (2/2) Prolonged deactivation of the Operating faults When the system detects an operating system fault there will be a 3-second contin- You can deactivate the system perma- uous beep as a warning. Please see an nently by pressing and holding switch 2. authorised dealer.
  • Page 116 2.22...

  • Page 117: Your Comfort

    Section 3: Your comfort Air vents: air outlets ............. . Air conditioning, heating .

  • Page 118: Air Vents: Air Outlets

    AIR VENTS: air outlets (1/2) 1 Demister outlets, side windows. 4 Centre air vents. 2 Side air vents. 5 Footwell vents. 3 Demisting outlets for the windscreen. 6 Control panel...
  • Page 119 AIR VENTS: air outlets (2/2) To remove bad odours from your ve- hicles, only use the systems designed for this purpose. Consult an approved Dealer. Centre air vents Side air vents Settings Settings Air flow: Air flow: Move the control knob 7 (beyond the Move the control knob 10 (beyond the resistance point).
  • Page 120 HEATING, AIR-CONDITIONING (1/3) Switching air conditioning on or off The air conditioning is switched on (in- dicator light illuminated) or off (indicator light extinguished) using button 6. The air conditioning system is used for: – lowering the temperature inside the passenger compartment;...

  • Page 121: Passenger Compartment

    HEATING, AIR-CONDITIONING (2/3) The air flow is directed to the windscreen demisting vents, the side windows and the passenger footwells. This is the recommended position for the best temperature in cold weather. The air flow is directed mainly ó towards the footwells. The air flow is directed to all air vents and the footwells.

  • Page 122: Adjusting The Ventilation Speed

    HEATING, AIR-CONDITIONING (3/3) Adjusting the ventilation speed Normal use Turn control 3 to one of the four posi- tions to start the ventilation system and adjust the power. Select position 1 for minimum ventila- tion and position 4 for maximum ven- tilation.

  • Page 123: Air Conditioning, Heating

    AIR CONDITIONING/HEATING: programming (1/2) Adjusting the programming Operating conditions – the ignition must be switched off; This function enables the electric net- work (and the not the traction battery) – the battery charging must be finished to be used under certain conditions, in for the function to be triggered;...
  • Page 124 AIR CONDITIONING/HEATING: programming (2/2) – hold down button B on stalk 3 - the Activating the function minutes flash; – With the ignition on, control 1 on – press button A to adjust them; – confirm by pressing button B on –...

  • Page 125: Additional Heating

    ADDITIONAL HEATING (1/2) Depending on the vehicle, the addi- Conditions of use tional heating is designed to heat the – The engine must be running; passenger compartment. Powered by a dedicated fuel tank (please see – switch 4 must be engaged; “Additional heating tank”...
  • Page 126 ADDITIONAL HEATING (2/2) Operating fault If the additional heating does not switch – start the vehicle; – switch on the heating by pressing switch 4; – wait for 5 minutes; – turn off the heater; – switch off your vehicle ignition; –...

  • Page 127: Air Conditioning: Information And Advice On Use

    AIR CONDITIONING: information and advice on use. Range Operating faults It is normal to notice an increase in As a general rule, contact your ap- energy usage when the air conditioning proved Dealer in the event of an oper- is operating. ating fault.

  • Page 128: Interior Lighting

    INTERIOR LIGHTING (1/2) Courtesy lights Luggage compartment light A Luggage compartment light B (depending on vehicle) (depending on vehicle) Pressing switch 1 gives: Tilt the switch 2 for permanent lighting. – permanent lighting; – intermittent lighting, which comes on when a door is opened. It goes out when the doors concerned are prop- erly closed;...

  • Page 129: Special Features

    INTERIOR LIGHTING (2/2) Special features Depending on the vehicle, remote un- locking of the doors triggers timed light- ing of the passenger compartment. If one of the front or rear doors is opened, the period for which the light is switched on will start again.

  • Page 130: Sun Visor/Mirror

    SUN VISOR/MIRRORS Front sun visor Courtesy mirror 2 (passenger side) Lower sun visor 1. If the sun visor is fitted with a courtesy The clip can be used to hold motorway mirror, it has a cover. passes, etc.. When driving, ensure the courtesy mirror cover is closed.

  • Page 131: Electric Windows

    ELECTRIC WINDOWS (1/2) Driver’s responsibility Never leave your vehicle Electric windows From the front passenger seat with the remote control unit inside and never leave a Operate switch 3. With the ignition on: child (or a pet) unsupervised, even for a short while. –...

  • Page 132: Half-Opening Window

    ELECTRIC WINDOWS /HALF-OPENING WINDOW (2/2) One-touch electric window Half-opening window (depending on vehicle) To half-open the window, turn handle 4 The one-touch mode works in addition in the direction of the arrow, then lock it to the operation of the electric windows by pushing the handle.

  • Page 133: Cigarette Lighter

    ASHTRAYS, CIGARETTE LIGHTER, ACCESSORIES SOCKETS Accessories sockets You may use the cigarette lighter recess 2 or one of sockets 3 (depend- ing on the vehicle). They are designed for connecting accessories with a maxi- mum power rating of 120 Watts (volt- age: 12V) which have been approved by our Technical Department.
  • Page 134 PASSENGER COMPARTMENT STORAGE, FITTINGS (1/3) Glovebox Dashboard storage compartment 2 To open the glovebox, lift catch 1. Centre console storage compartment 3 To open, lift cover 4. It will store a 1.5 litre bottle. When turning corners, accelerating or braking, ensure that the recepta- cle being held by the cup holder is not dislodged.
  • Page 135 PASSENGER COMPARTMENT STORAGE, FITTINGS (2/3) Front door storage Sliding side door storage Clip 8 compartments 5 compartments 7 This can be used for storing motorway tickets, cards, etc. Bottle holders 6 Sunglasses holder 9 There is a dedicated storage compart- ment in the centre.
  • Page 136 PASSENGER COMPARTMENT STORAGE, FITTINGS (3/3) Clothes hook 10 Depending on the vehicle, a hook may be located on the partition behind the front passenger seat. For safety reasons, this hook may only be used to hang clothes. NB: the maximum permitted load is 4 kg.

  • Page 137: Rear Bench Seat

    REAR BENCH SEAT: functions (1/2) For safety reasons, carry out any adjustments when the vehicle is not being driven. When moving the rear bench seat, make sure the bench seat anchor- age points are clean (they should be free from grit, cloths etc.). To fold down the seatback To raise the seatback Before moving the bench seat, make...
  • Page 138 REAR BENCH SEAT: functions (2/2) Use restriction It is forbidden to drive with a seatback or a front seat folded down when there is a passenger occupying a rear seat. For safety reasons, carry out any adjustments when the vehicle is not being driven.

  • Page 139: Rear Headrests

    REAR HEADRESTS To raise it Storage position 2 Child’s convertible headrest Slide it to the required height. Pull it towards you and lower it com- If fitted to the vehicle, the child head- pletely. rest and booster cushion can only be To lower it The fully lowered headrest position installed on the rear side seats.

  • Page 140: Transporting Objects

    TRANSPORTING OBJECTS IN THE BOOT (1/2) Always position the objects trans- ported so that the largest surface is against: – the rear bench seatbacks, for normal loads; – the front seats for maximum loads. Always position the hea- viest items directly on the floor.
  • Page 141 TRANSPORTING OBJECTS IN THE BOOT /TOWING (2/2) A = 830 mm. Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. For fitting and conditions of use, If the towbar ball obscures the regis- refer to the equipment’s fitting ins- tration plate or the rear fog lights, it tructions.

  • Page 142: Luggage Net

    LUGGAGE NET The luggage net Positioning the net 2 (depending on vehicle) – Upper section: insert the tabs at the This is located in the luggage compart- ends of the net in hooks 1; ment. – lower section: engage belts 3 in lashing rings 4 on the floor.

  • Page 143: Multimedia Equipment

    MULTIMEDIA EQUIPMENT The presence and location of this equipment depends on the vehicle’s multimedia equipment. 1 Multimedia touchscreen; 2 multimedia sockets; 3 radio; 4 steering column control. To operate this equipment: please refer to the instructions for the equip- ment which should be kept with the other vehicle documentation.
  • Page 144 3.28...
  • Page 145 Section 4: Maintenance Bonnet ............... . Levels .

  • Page 146: Bonnet

    BONNET (1/2) To open the bonnet, pull the handle 1. Unlocking the bonnet catch To open, push tab 2 to the left as you open the bonnet. Do not do any work under the bonnet when the vehicle Opening the bonnet is charging or when the igni- Lift the bonnet, helping it up, and it will tion is switched on.

  • Page 147: Closing The Bonnet

    BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and lower it to 30 cm above the closed position, then release it. It will latch automatically under its own weight.

  • Page 148: Levels

    LEVELS (1/2) Replacement intervals Refer to the Maintenance Document for your vehicle. The engine may be hot when carrying out opera- tions in close proximity. In addition, the engine cooling fan can come on at any moment. Coolant Checking intervals Risk of injury.

  • Page 149: Brake Fluid Level

    LEVELS (2/2) Level 3 It is normal for the level to drop as the linings become worn, but it should never drop below the “MINI” warning line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from our network or from the manufacturer’s website.

  • Page 150: Battery

    12 VOLT BATTERY (1/2) Never open the battery cover 1. The charge status of the 12V battery can decrease, especially if you use your vehicle: – when the exterior temperature drops; – after extended use of energy-con- suming devices (radio etc.) with the engine switched off.
  • Page 151 12 VOLT BATTERY (2/2) Label A Observe the indications on the battery: – 2 naked flames and smoking are for- bidden; Do not do any work under – 3 eye protection required; the bonnet when the vehicle – 4 keep away from children; is charging or when the igni- –...

  • Page 152: Tyre Pressure

    TYRE PRESSURE D : tyre pressures for the front wheels (motorway). E : tyre pressures for the rear wheels (motorway). Special note concerning fully laden vehicles (Maximum Permissible All-Up Weight) and towing a trailer: the maxi- mum speed must be limited to 60 mph (80 km/h) and the tyre pressure in- creased by 0.2 bar.

  • Page 153: Bodywork Maintenance

    BODYWORK MAINTENANCE (1/2) What you should not do You should A well-maintained vehicle will last longer. It is therefore recommended to Do not degrease or clean mechani- Wash your car frequently, with the maintain the exterior of the vehicle reg- cal components (e.g.
  • Page 154 BODYWORK MAINTENANCE (2/2) Using a roller type car wash Cleaning the headlights Observe the vehicle stopping distances when driving on gravelled surfaces to Return the windscreen wiper stalk to As the headlights are made of plastic prevent paint damage. the Park position (refer to the informa- “glass”, use a soft cloth or cotton wool Repair, or have repaired quickly, areas tion on the “Windscreen washer, wiper”...

  • Page 155: Interior Trim Maintenance

    INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
  • Page 156 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.

  • Page 157: Practical Advice

    Section 5: Practical advice Puncture ..............Emergency spare wheel .

  • Page 158: Emergency Spare Wheel 2

    PUNCTURE/EMERGENCY SPARE WHEEL In the event of a puncture, there is To access the emergency spare either an emergency spare wheel or wheel tyre inflation kit available, depending on – Open the tailgate. the vehicle (refer to the information in –...

  • Page 159: Tyre Inflation Kit

    TYRE INFLATION KIT (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
  • Page 160 TYRE INFLATION KIT (2/3) With the engine running and the – after a maximum of 15 minutes, stop parking brake applied, inflating and read the pressure (on pressure gauge 5). – unroll the hose from the container; Note: while the container is empty- –...
  • Page 161 TYRE INFLATION KIT (3/3) – Affix the driving recommendation Precautions when using the kit label to the dashboard where it can The kit should not be operated for more easily be seen by the driver; than 15 consecutive minutes. – Put the kit away. –...

  • Page 162: Tool Kit

    TOOL KIT Jack 10 Refer to Section 5 “Changing a wheel”. Retaining belt (depending on vehicle) After use, reposition the strap making sure that it retains all components in the tool kit. Do not leave the tools un- secured inside the vehicle as they may come loose under braking.

  • Page 163: Wheels, Trim

    WHEELS, TRIM Wheel trim 1 Wheel trim 3 (concealed wheel bolts) (exposed wheel bolts) Remove it using hubcap tool 2 (located To remove it without removing the under the tool kit), by pushing the hook wheel, press it at the points indicated into the opening located near the valve by the arrows.

  • Page 164: Changing A Wheel

    CHANGING A WHEEL (1/2) Continue tightening to position the baseplate on the ground correctly. Turn handle 3 on the jack to lift the wheel off the ground. If the vehicle is parked on the hard shoulder, you must warn other road users of If necessary, remove the wheel trim.
  • Page 165 CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. For vehicles fitted with alloy wheels, use the guide bolt located in the tool kit to finish loosening and start tightening the bolts. Fit the emergency spare wheel on the central hub and turn it to align the mounting holes in the wheel and the hub.

  • Page 166: Tyres

    TYRES (1/3) Tyre and wheel safety When the tyre tread has been eroded to the level of the warning strips, they The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.

  • Page 167: Tyre Pressures

    TYRES (2/3) Tyre pressures Fitting new tyres Pressures should be checked when the tyres are cold; ignore higher pressures Respect the tyre pressures (including which may be reached in hot weather the emergency spare wheel). Check or following a fast journey. them at least once a month and before For safety reasons, this op- a long journey (refer to the label on the...
  • Page 168 TYRES (3/3) Use in winter – Snow or winter tyres We would recommend that these be The use of snow tyres, winter tyres or – Chains fitted to all four wheels to ensure studded tyres significantly reduces the For safety reasons, fitting snow that your vehicle retains maximum vehicle range.

  • Page 169: Headlights: Changing Bulbs

    HEADLIGHTS : changing bulbs (1/2) Front side light Open the cover 1. Disconnect the bulb holder wiring 4. Remove bulb holder 4 from its housing. Replace the bulb. Bulb type: W5W To refit it, carry out the above opera- tions in reverse order. Dipped beam/main beam Bulb type: H4 It is essential to use 55W anti UV bulbs...
  • Page 170 HEADLIGHTS : changing bulbs (2/2) Direction indicator lights Turn the bulb holder 5 to release it and remove it from its location without dis- connecting the wiring. Replace the bulb. Bulb type: PY21W To comply with local legislation, or To refit it, carry out the above opera- as a precaution, you can obtain an tions in reverse order.

  • Page 171: Fog Lights: Changing Bulbs

    FOG LIGHTS: changing bulbs Additional lights If you wish to fit your car with fog lights or long range headlights, contact an au- thorised dealer. The bulbs are under pres- Front fog lights 1 Rear fog lights 2 sure and can break when replaced.

  • Page 172: Rear Lights: Changing Bulbs

    REAR LIGHTS: changing bulbs (1/3) Rear lights Bulb type Depending on the vehicle, open the 4 Indicator hinged doors or the tailgate. Pear-shaped, bayonet type bulb Undo bolts 1 using a Torx tool. P Y21W. Unclip the lower section, then the upper 5 Side and brake light section of the light by pulling it towards Pear-shaped, bayonet type bulb...
  • Page 173 REAR LIGHTS: changing bulbs (2/3) High-level brake light Remove the two plastic blanking covers 7 from the inside. Unclip the – Version with tailgate: it is located light using a screwdriver, by pressing in above the rear screen, in the centre. the metal clip housings.
  • Page 174 REAR LIGHTS: changing bulbs (3/3) Number plate light Release the light 10 to access bulbs. Undo two bolts 9 using a Torx tool. Bulb type: W5W. Replace the bulbs, then fit the light in position. 5.18...

  • Page 175: Indicator Lights: Changing Bulbs

    INDICATOR LIGHTS: changing bulbs Unclip indicator light 1 on the door side, Turn the bulb holder 2 a quarter of a using a flat-blade screwdriver type tool. turn and take out the bulb. Bulb type: WY5W. Replace the bulb and refit the indicator light.

  • Page 176: Interior Lights: Changing Bulbs

    INTERIOR LIGHTS: changing bulbs (1/2) Passenger compartment Pull the bulb 2 to remove it from its housing. lights Remove the lens 1 using a tool such as Bulb type 2: W6W a flat-blade screwdriver. Rear courtesy light bulb type: W6W Replace the bulbs and replace the lens.
  • Page 177 INTERIOR LIGHTS: changing bulbs (2/2) Light A Light B or C Remove the lens using a tool such as a Remove the lens using a tool such as a flat-blade screwdriver. flat-blade screwdriver. Pull the bulb to remove it from its hous- Pull the bulb to remove it from its hous- ing.

  • Page 178: Connecting A Battery Charger

    12 VOLT BATTERY: breakdown recovery (1/2) To avoid all risk of sparks: Connecting a battery charger Disconnect the leads connected to both battery terminals, starting with the – Switch off the vehicle ignition. The battery charger must be com- negative terminal. –...
  • Page 179 12 VOLT BATTERY: breakdown recovery (2/2) Starting the vehicle using the Check that there is no contact between the cables A and B and that the (+) battery from another vehicle cable A is not touching any metal parts If you have to use the battery from an- on the vehicle supplying the current.

  • Page 180: Fuses

    FUSES (1/2) To locate the fuses, please see the fol- lowing page. It is not advisable to use the free fuse locations. Some functions are protected by fuses located in the engine compartment. However, because of their reduced ac- cessibility, it is recommended to have these fuses replaced by an autho- rised dealer.
  • Page 181 FUSES (2/2) Number Allocation Number Allocation Traction battery charger Brake lights, additional equipment, navigation, ABS, Electric motor control unit ESP, boot light, interior lights, rain and light sensor, Air conditioning, pedestrian charging warning light horn heating, brake lights, Radio, navigation system, traction battery display, alarm 11 12 13 14...

  • Page 182: Windscreen Wiper Blades

    WINDSCREEN WIPER BLADES (1/2) Replacing windscreen wiper Replacing windscreen wiper blades 2 blades 3 – With the ignition switched off, lift – With the ignition on and the engine wiper arm 2 slightly; switched off, lower the windscreen wiper stalk fully: they stop slightly –...
  • Page 183 WINDSCREEN WIPER BLADES (2/2) Replacing the rear screen Tailgate versions C – In frosty weather, make wiper blade – With the ignition switched off, lift sure that the wiper blades wiper arm 9; are not stuck by ice (to Hinged door versions B avoid the risk of the motor –...

  • Page 184: Towing, Breakdown

    TOWING, BREAKDOWN (1/3) Choice of breakdown service In the event of an energy fault In the event of a fully discharged trac- tion battery, any type of towing is per- mitted: towing on a flatbed truck or towing on the road using the tow eye (please see following pages).
  • Page 185 TOWING, BREAKDOWN (2/3) In the event of an energy Before towing, insert the key in the Bring lever to position N. switch to unlock the steering column. fault: towing Turn it to position M. In the event of a fully discharged trac- The column is unlocked, the acces- tion battery: sory functions are supplied: the vehi-...
  • Page 186 TOWING, BREAKDOWN (3/3) Access to towing points Only use the front and rear towing points (never use the driveshafts). Unclip cover 3 or 5. These towing points may only be used Tighten the tow eye 4 fully: as much for towing: never use them for lifting the as possible by hand at first, then finish vehicle directly or indirectly.

  • Page 187: Fitted Audio Equipment

    FITTED AUDIO EQUIPMENT If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – radio 1; – tweeter speakers 2; – bass speakers 3. To install any equipment, please con- sult an approved dealer.

  • Page 188: Accessories

    ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. To install an accessory requiring intervention with the vehicle’s 12V electrical circuit, please follow these instructions: –...
  • Page 189 RADIO FREQUENCY REMOTE CONTROL: batteries Replacing the remote control Replace battery 2 according to the di- rection marked on the cover. battery Note: It is not advisable to touch the Undo screw 1 to remove the remote electronic circuit in the key cover when control cover.

  • Page 190: Operating Faults

    OPERATING FAULTS (1/4) The following advice will enable you to carry out quick, temporary repairs. For safety reasons, you should always contact an approved Dealer as soon as possible. FAULTS POSSIBLE CAUSES WHAT TO DO Impossible to charge the traction bat- No electrical current in domes- Check your installation (circuit breaker, pro- tery.
  • Page 191 OPERATING FAULTS (2/4) FAULTS POSSIBLE CAUSES WHAT TO DO The additional heating does not work. Fill up the fuel tank. Fill up with fuel – see information on the “Additional heating tank” in Section 1. The programmable heating does not One of the usage conditions is not Refer to the information on “Heating/air work.
  • Page 192 OPERATING FAULTS (3/4) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved Dealer. Vibrations. Tyres not inflated to the correct pres- Check tyre pressures. If this is not the prob- sure, incorrectly balanced or dam- lem, have them checked by an authorised aged.
  • Page 193 OPERATING FAULTS (4/4) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved Dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”.
  • Page 194 5.38...

  • Page 195: Technical Specifications

    Section 6: Technical specifications Vehicle identification plates ............Engine identification plate .

  • Page 196: Vehicle Identification Plates

    VEHICLE IDENTIFICATION PLATES The information shown on the ve- 5 GTW (Gross train weight: vehicle hicle identification plate should be fully loaded, with trailer). quoted on all correspondence or orders. 6 MPAW (Maximim Permissible Weight) for front axle. Vehicle identification plate A 1 Manufacturer name.

  • Page 197: Engine Identification Plate

    ENGINE IDENTIFICATION PLATE/ENGINE SPECIFICATIONS Engine identification plate Engine specification Quote the details given on engine Engine type 1: 5AM plate C on all communication or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.

  • Page 198: Dimensions

    DIMENSIONS (in metres) (1/2)
  • Page 199 DIMENSIONS (in metres) (2/2) 2 seater 5 seater Medium Long H (unladen) Turning circles between kerbs 10.7 11.9 Turning circles between walls 11.2 12.4...

  • Page 200: Weights

    WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact an approved Dealer. Medium long Maximum permissible all-up weight (MMAC) Weights are indicated on the vehicle identification plate (refer to Total train weight (MTR) the information on “Vehicle identification plates”...

  • Page 201: Replacement Parts And Repairs

    REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.

  • Page 202: Service Sheets

    SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 203 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 204 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 205 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 206 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
  • Page 207 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...

  • Page 208: Anticorrosion Check

    ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.14...
  • Page 209 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
  • Page 210 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
  • Page 211 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
  • Page 212 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...

  • Page 213: Alphabetical Index

    ALPHABETICAL INDEX (1/5) ABS ...............2.10 → 2.12 changing a bulb ....... 5.13 → 5.15, 5.19 → 5.21 accessories................ 5.32 changing a wheel..............5.8 accessories socket ............3.17 changing gear ............. 2.3 – 2.4 additional heating fuel............1.88 charge meter ............1.66, 2.5, 2.8 additional heating tank............
  • Page 214 ALPHABETICAL INDEX (2/5) driving position settings ............1.34 → 1.37 faults operating faults ..........5.34 → 5.37 fitting a radio ..............5.31 »ECO» mode function ..........2.5, 2.9 fittings ..............3.18 → 3.20 ECO driving ................. 2.9 fog lights ..............1.82, 5.15 »400 volt» electrical circuit ........1.2 → 1.7 front lights electric vehicle changing bulbs ..........
  • Page 215 ALPHABETICAL INDEX (3/5) hubcap tool ................5.6 fog lights ............ 1.62, 1.82, 5.15 hazard warning ............1.78 main beam headlights ......1.62, 1.80 – 1.81 indicators ............1.78, 5.14, 5.19 number plate lights ............5.18 indicators: reversing lights ............. 5.16 direction indicators ..........
  • Page 216 ............... 5.33 in the event of energy failure ......5.28 → 5.30 remote control electric door locking ......1.15, 1.17 breakdown ............5.28 → 5.30 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.25 towing equipment replacement parts ..............6.7 fitting ................3.25 reverse gear towing hitch............
  • Page 217 ALPHABETICAL INDEX (5/5) trip computer and warning system... 1.62 → 1.64, 1.70 → 1.76 tyre inflation kit............5.3 → 5.5 tyre pressure................ 4.8 tyre pressures ..........4.8, 5.10 → 5.12 tyres ..............4.8, 5.10 → 5.12 unlocking the doors ..........1.23 – 1.24 vehicle identification ............
  • Page 219 Pour ranger les documents de votre nouveau véhicule Z.E., RENAULT a développé pour vous une pochette fabriquée à partir de matières recyclées et recyclables. To store documents in your new vehicle Z.E., RENAULT has developed for you a pocket made from recycled and recyclable materials.
  • Page 220 à999107539Rï ê ô ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Table of Contents