Renault kangoo storia Driver's Handbook Manual
  1. Manuals
  2. Brands
  3. Renault Manuals
  4. Automobile
  5. kangoo storia
  6. Driver's handbook manual
Renault kangoo storia Driver's Handbook Manual

Renault kangoo storia Driver's Handbook Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
KANGOO STORIA
KANGOO CAMPUS
DRIVER'S HANDBOOK

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the kangoo storia and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Renault kangoo storia

Summary of Contents for Renault kangoo storia

  • Page 1 KANGOO STORIA KANGOO CAMPUS DRIVER’S HANDBOOK...
  • Page 2 RENAULT vehicles. ELF lubricants are a major factor in your vehicle’s performance. RENAULT recommends the approved ELF lubricants for your oil changes and top-ups. Contact your RENAULT representative or visit the site: www.lubricants.elf.com The oil born in Formula One...

  • Page 3: Driving

    Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle. Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from RENAULT, 92 100 Billancourt 2009.

  • Page 5: Table Of Contents

    Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
  • Page 6 TYrE PrESSurE wHEN COlD (in bar) Tyre dimensions 165/70 r 14 C 165/70 r 14 175/70 r 14 175/65 r 14 175/65 r 14 reinf. 85r or S reinf. 88T reinf. 86T Non-motorway use – Front – Rear Full load use and/or motorway driving (1) –...
  • Page 7 Section 1: Getting to know your vehicle Key, radio frequency remote control: general information, use ......Doors .

  • Page 8: Key, Radio Frequency Remote Control: General Information, Use

    KEY/RADIO FREQUENCY REMOTE CONTROL: general information (1/2) 1 Coded key for ignition switch, 2 Key for ignition switch, doors and 3 Key for ignition switch, doors and doors and fuel filler cap. fuel filler cap. fuel filler cap. 4 Battery tell-tale light Advice Avoid leaving the remote control in hot, cold or humid areas.
  • Page 9 KEY/RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the environ- ment. It is therefore important when handling the remote control to ensure For replacement, or if you that you do not lock or unlock the ve- require an additional remote hicle by inadvertently pressing the but- control...
  • Page 10 RADIO FREQUENCY REMOTE CONTROL: use Door locking/unlocking Press remote control 1 for approxi- mately one second to lock (side B) or unlock (side A) the doors. The side indicator lights and hazard warning lights flash twice to indicate that the doors have been locked. Note: depending on the vehicle, if either a door or the luggage compart- ment lid is open or not properly closed,...

  • Page 11: Doors

    DOORS (1/4) Opening from the outside Opening from the inside Closing from the inside Pull handle 5 towards the front of the Pull handle 4 or 6. Opening the front doors from the vehicle until the door is completely outside Lights-on warning buzzer closed.
  • Page 12 DOORS (2/4) Recommendations con- cerning the sliding side door The following precautions must be taken when opening and closing the doors or any other open- ing element: – check that the door will not come into contact with any person, animal or object;...
  • Page 13 DOORS (3/4) Closing manually from the outside First close the small door and then close the large door. Retaining rods 10 will engage automat- ically in their housings. Rear hinged doors To open the rear doors completely To open the doors completely, move Opening manually from the outside aside handle 9 and open the door com- Unlock using the same key as for the...
  • Page 14 DOORS (4/4) Rear hinged doors Tailgate (continued) Opening manually from the outside Opening from the inside To unlock, insert the ignition key into lock 12. The small door can be opened from inside the vehicle by turning handle 11 To open, place your hand behind If the vehicle is parked on downwards.

  • Page 15: Locking/Unlocking The Doors

    LOCKING/UNLOCKING THE DOORS (1/2) Electric central locking Manual locking Sliding side door (right-hand side) This enables all the doors to be locked Front door simultaneously. From outside, insert the key fully into Use the key if outside or, if inside the lock 3 and lock the door.
  • Page 16 LOCKING/UNLOCKING THE DOORS (2/2) Sliding side door (fuel filler When the fuel tank has been filled, refit the cap. The locking button is opera- cap side) tional again. This door does not have a lock on the For vehicles without remote control outside.

  • Page 17: Automatic Locking When Driving

    AUTOMATIC LOCKING WHEN DRIvING (RAID) You must first decide if you want to activate this function. To activate With the ignition on, press button 1 on the locking side (opposite the symbol) for approximately 5 seconds, until you hear the bleep. To deactivate With the ignition on, press button 1 on the unlocking side (symbol) for ap-...

  • Page 18: Engine Immobiliser

    ENGINE IMMOBILISER ê Immobiliser warning Diesel version light If tell-tale light 1 comes on or remains lit after the ignition has been switched This prevents the engine from being on, this indicates that the system is not started by anyone not in possession operating correctly.

  • Page 19: Headrests

    FRONT HEADRESTS To raise or lower the headrest Pull the headrest towards you (i.e. to- wards the front of the vehicle) and slide it up or down at the same time. To remove the headrest First incline the seatback towards the rear.

  • Page 20: Rear Headrests

    REAR HEADRESTS To refit the headrest Insert the rods into the holes, with the notches to the front, and lower the headrest to the desired height by press- ing the tab. Storage position A Press headrest guide tabs 1 and lower the headrest completely.

  • Page 21: Front Seats

    FRONT SEATS To move forwards or backwards To tilt the seatback Stay in your seat and raise bar 1 to Move lever 2 until the seatback is at the unlock it. desired angle. We would advise you not to recline the seatbacks too far to ensure that the effectiveness of the seat belts is not reduced.

  • Page 22: Partition

    SWIvELLING PARTITION Using the swivelling – Release the swivelling section by lift- Note: before returning the swivelling ing catch 5 until it locks in position. section to its original position, check bulkhead that locking point 4 is clean and not ob- –...

  • Page 23: Rear View Mirrors

    REAR vIEW MIRRORS Interior rear view mirror Door mirror Electrically-adjustable door mirrors The interior rear view mirror is adjust- To adjust the mirror, move lever 2. able. When driving at night, tilt small With the ignition on, move button 3: lever 1 to avoid being dazzled by the –...

  • Page 24: Seat Belts

    SEAT BELTS (1/4) Adjusting your driving Always wear your seat belt when trav- elling in your vehicle. You must also position comply with the legislation of the par- (certain adjustments depend on the ve- ticular country you are in. hicle’s equipment level) Before starting, first adjust your driv- –...
  • Page 25 SEAT BELTS (2/4) ç Front seat belt reminder warning light This comes on when the engine is started if the driver’s or front passenger’s seat belt (if the passenger seat is occupied) is not buckled. A beep sounds at a low volume for 30 seconds, then at a high volume for 90 seconds.
  • Page 26 SEAT BELTS (3/4) Rear side seat belts The belts are locked, unlocked and adjusted in the same way as the front belts. Rear centre belt with inertia Rear lap belt with manual reel adjustment Slowly unwind belt 7 until black buckle 8 The belts are fastened and unfastened clicks into catch 9.
  • Page 27 SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. For special operations (e.g. fitting child seats) contact an approved Dealer. –...

  • Page 28: Methods Of Restraint In Addition To The Front Seat Belts

    METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/5) These are: – Have the entire restraint – pretensioners, system checked following an accident. – force limiter, – No operation whatso- – driver’s and passenger air bags. ever is permitted on any part of These systems are designed to act the system (pretensioners, air independently or together when the...
  • Page 29 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/5) Load limiter Above a certain level of impact force, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Air bags for driver and front Each air bag system consists of: passenger...
  • Page 30 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/5) Depending on the vehicle, the passen- ger air bag system is linked to a front passenger air bag deactivation warn- ing light 2 on the instrument panel. This warning light is linked to the passenger air bag deactivation system using the ignition key.
  • Page 31 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/5) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
  • Page 32 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (5/5) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.

  • Page 33: Child Safety: General Information

    CHILD SAFETY: general information Carrying children Using a child seat Set a good example by always fas- The level of protection offered by the Children, and adults, must be correctly tening your seat belt and teaching child seat depends on its ability to re- seated and strapped in for all journeys.
  • Page 34 CHILD SAFETY: Choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need From 15 kg or 4 years, the child can than that of an adult and its neck is very to be protected as a priority.
  • Page 35 CHILD SAFETY: choice of child seat mounting Attachment via the seat belt Do not use the child seat The seat belt must be adjusted to if it may unfasten the seat ensure that it is effective in the event of belt restraining it: the base harsh braking or an impact.

  • Page 36: Fitting A Child Seat

    CHILD SAFETY: Fitting a child seat (1/7) In the front seat Some seats are not suitable for fitting In the rear seat child seats. The diagrams on the fol- The laws concerning children travel- A carrycot can be installed across the lowing pages show you how to attach ling in the front passenger seat differ in vehicle and will take up at least two...
  • Page 37 CHILD SAFETY: Fitting a child seat (2/7) 2-seat versions with folding two-part passenger seat ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. Child seat attached using the belt U = Seat which allows a seat with “uni- versal”...
  • Page 38 CHILD SAFETY: Fitting a child seat (3/7) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. 2-seat version Type of child seat With passenger air bag Without passenger air bag Standard front Standard front...
  • Page 39 CHILD SAFETY: Fitting a child seat (4/7) 4- and 5-seat versions with single section rear bench seat: seat ² installation diagram Seat not suitable for fitting child seats. It is forbidden to carry a passenger or fit a child seat Child seat attached using the belt ³...
  • Page 40 CHILD SAFETY: Fitting a child seat (5/7) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. 4- and 5-seat versions with single section rear bench seat Type of child seat Standard front Rear side seats...
  • Page 41 CHILD SAFETY: Fitting a child seat (6/7) Child seat attached using the belt ³ U = Seat which allows a seat with “uni- Check the status of the air bag versal” approval to be attached using a before fitting a child seat or allowing a belt.
  • Page 42 CHILD SAFETY: Fitting a child seat (7/7) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. 5-seat version with 1/3-2/3 bench seat Type of child seat Standard front Rear side seats Rear centre seat...

  • Page 43: Deactivating/Activating The Front Passenger Air Bag

    CHILD SAFETY: deactivating/activating the front passenger air bag (1/2) Deactivating the front To deactivate the air bags: with the DANGER vehicle stationary and the ignition off, passenger air bags insert the ignition key in lock 1 and turn Since front passenger air (on equipped vehicles) bag triggering and the po- to the OFF position.
  • Page 44 CHILD SAFETY: deactivating/activating the front passenger air bag (2/2) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the air bag activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended.

  • Page 45: Audible And Visual Signals

    AUDIBLE AND vISUAL SIGNALS é Horn Hazard warning lights Direction indicators Press at one of the locations 2. Press switch 3. This device si- Move stalk 1 parallel to the steering multaneously activates the four direc- wheel and in the direction you are going tion indicators and the side indicator to turn it.

  • Page 46: Driving Position

    DRIvING POSITION: LEFT-HAND DRIvE (1/2) 9 10 22 21 1.40...

  • Page 47: Instrument Panel

    DRIvING POSITION: LEFT-HAND DRIvE (2/2) The equipment fitted, described below, DEPENDS ON THE vERSION AND COUNTRY. 1 Side air vent. 10 Storage compartment 21 Hazard warning lights switch. 2 Location for speaker. 11 Passenger air bag location. 22 Ignition switch. 3 Stalk for: 12 Location for speaker.
  • Page 48 INSTRUMENT PANEL: warning lights (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Heated rear screen warning Low fuel level warning light light Front fog light tell-tale light This goes out as soon as the engine starts.
  • Page 49 INSTRUMENT PANEL: warning lights (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ô Coolant temperature warn- Electronic fault and water ing light present in diesel fuel warn- If it comes on while you are driving, ing light (on petrol and diesel stop and let the engine idle for a minute versions) and preheating warning...
  • Page 50 INSTRUMENT PANEL: warning lights (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ä Handbrake “on” warning Warning light for monitoring light and brake circuit inci- exhaust gas dent warning light It comes on when the ignition is switched If it comes on during braking, it indicates on and then goes out.
  • Page 51 INSTRUMENT PANEL: warning lights (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. û Æ STOP light Serious injection fault warn- ing light/Coolant tempera- ture warning light This goes out as soon as the engine starts.

  • Page 52: Coolant Temperature

    INSTRUMENT PANEL: display and indicators (1/2) Rev counter 1 Speedometer 2 Fuel gauge 3 (scale ×100) (km or miles per hour) The number of squares lit shows the fuel level. When it is at minimum, the squares disappear and the low fuel level warning light comes on.
  • Page 53 INSTRUMENT PANEL: display and indicators (2/2) Multifunction key 5 Depending on the vehicle, repeatedly pressing button 5 allows information to be brought up on the display, the trip mileage recorder to be reset (the trip mileage recorder must be selected on the display for this operation) or the clock to be set.

  • Page 54: Clock

    CLOCK Clock 1 Resetting the clock With the ignition on, and display 1 set to total mileage recorder and clock, press and hold button 2, to access “clock setting” mode (clock flashes) If the electrical supply is cut (battery then release the button. disconnected, broken supply wire, etc.), the clock will lose its time set- –...
  • Page 55 ELECTRICAL ADJUSTMENT OF THE DIPPED BEAM HEADLIGHTS Examples of positions for adjusting Load status control A according to the load. Driver only or with passenger All seats occupied Intermediate position According to driver’s judgement Driver only with luggage compartment laden Increased payload version: 4 Control knob A is used to adjust the height of the headlight beams accord-...

  • Page 56: External Lighting And Signals

    EXTERNAL LIGHTING AND SIGNALS (1/2) Main beam headlights With stalk 1 in dipped beam headlights position, move the stalk to- wards you. When the main beam headlights are lit, an indicator light lights up on the instru- ment panel. To return to the dipped beam headlight position, pull the stalk towards you.

  • Page 57: Rear Fog Light

    EXTERNAL LIGHTING AND SIGNALS (2/2) Rear fog light Switching off the lights Turn the centre ring of stalk 1 Bring stalk 1 back to the zero position. until the symbol is opposite mark 3. Operation of the fog lights depends on Lights-on warning buzzer the exterior lighting selected, and an in- dicator light will light up on the instru-...

  • Page 58: Screen Wash/Wipe

    WINDSCREEN WASH/WIPE Special note Windscreen washer When the vehicle is being driven, the wiping speed slows down when- With the ignition on, pull stalk 1 towards ever the vehicle stops. The speed will you. change from fast wipe speed to normal A short press triggers one sweep cycle wipe speed.
  • Page 59 REAR SCREEN WASH/WIPE Rear screen wash/wipe With the ignition on, turn the end of stalk 1 to align the symbol with mark 2. When the stalk is released, it returns to the rear screen wiper position. Check the condition of the wiper blades.

  • Page 60: Fuel Tank

    FUEL TANK (1/2) Fuel grade Fuel filler cap: this is spe- Use a high grade fuel that complies cific to the vehicle type. with the standards currently in force in If you have to replace it, each country. make sure it is identical to the original cap.
  • Page 61 FUEL TANK (2/2) Filling with fuel Petrol and diesel versions System for cutting off the fuel supply in the event of a When the pump cuts out automatically Petrol versions severe impact at the end of the filling procedure, a Use unleaded petrol only.
  • Page 62 1.56...
  • Page 63 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in/Ignition switch ............Starting/stopping the engine .

  • Page 64: Running In/Ignition Switch

    RUNNING IN/IGNItIoN SwItch Petrol version Ignition on position M For the first 600 miles (1,000 km) do The ignition is switched on: not exceed 54 mph (90 km/h) in the – petrol version: you may start the highest gear. engine; You may only expect top performance –...

  • Page 65: Starting/Stopping The Engine

    StARtING/StoPPING thE ENGINE É Starting the engine Diesel injection Stopping the engine With the engine idling, turn the key to Petrol injection Turn the ignition key to ignition on, the “Stop” position St. Engine warm or cold position M, and hold this position until the preheating warning light –...

  • Page 66: Special Features Of Petrol Versions

    SPEcIAl fEAtURES of PEtRol vERSIoNS The following operating conditions If you notice any of the above operating should be avoided: faults, have the necessary repairs car- ried out as soon as possible by an ap- – driving for long periods when the low proved dealer.

  • Page 67: Special Features Of Diesel Versions

    SPEcIAl fEAtURES of DIESEl vERSIoNS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment incorporating a mechanical To avoid any faults in icy weather: regulator which prevents overrevving – make sure that the battery is always of the engine irrespective of the gear fully charged;...

  • Page 68: Advice On Antipollution, Fuel Economy And Driving

    ADvIcE: antipollution, fuel economy and driving (1/3) Maintenance Engine adjustments Your vehicle has been designed to actively strive to reduce the pollutant It should be noted that failure to respect – Ignition: this does not require ad- exhaust gas emissions and to save antipollution regulations may lead to justment.
  • Page 69 ADvIcE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring – Brake as little as possible by suitably anticipating an obstacle or bend and system then simply releasing the accelerator The exhaust gas monitoring system pedal. will detect any operating faults in the –...
  • Page 70 ADvIcE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in city conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.

  • Page 71: Environment

    ENvIRoNMENt Recycling Make your contribution towards pro- Your vehicle has been designed with respect for the environment in mind for tecting the environment too. Your vehicle is 85% recyclable and its entire service life: during production, – Worn parts replaced in the course of 95% recoverable, in line with European use and at the end of its life.

  • Page 72: Gear Lever/Handbrake/Power-Assisted Steering

    GEAR lEvER/hANDBRAKE/PowER-ASSIStED StEERING handbrake Power-assisted steering If you have power-assisted steering to release: fitted, do not leave the steering wheel Pull the lever up slightly, press button 2 at full lock when the vehicle is parked and then lower the lever to the floor. as this may damage the pump.

  • Page 73: Anti-Lock Braking System

    ANtI-locK BRAKING SyStEM: ABS ABS (Anti-lock Braking operating faults: Depending on the vehicle, this is com- posed of: System) – If the warning light on the in- – ABS (anti-lock braking system); strument panel comes on while driv- Under heavy braking, the ABS prevents –...

  • Page 74: Emergency Brake Assist

    EMERGENcy BRAKE ASSISt Emergency brake assist This is an additional system to ABS which helps reduce vehicle stopping distances. operating principle The system detects an emergency braking situation. In this case, the brak- ing assistance immediately develops maximum power and may trigger ABS regulation.

  • Page 75: Your Comfort

    Section 3: Your comfort Air vents............... Rear screen and windscreen de-icing and demisting .
  • Page 76 Air vents, air outlets (1/2 1 Side window demisting and air vents. 5 Front footwell air vents. 2 Centre air vents. 6 Rear footwell air vents. 3 Demisting outlets for the windscreen. 7 Rear screen demisting switch. 4 Control panel.

  • Page 77: Air Vents

    Air vents, air outlets (2/2) To remove bad odours from your ve- hicle, only use the systems designed for this purpose. Consult an approved Dealer. side air vents Front central air vents settings settings Air flow: Air flow: Move the control knob 1 (beyond the Move control knob 3 (beyond the point resistance point).
  • Page 78 De-iCinG/DeMistinG Heated rear screen Demisting the windscreen and side windows With the engine running, press Move control 3 to position button 1 (depending on the vehicle, warning light 2, located on the button or For greater efficiency, close the the instrument panel, comes on). dashboard centre air vents.

  • Page 79: Heating System/Ventilation

    HeAtinG – ventiLAtiOn (1/2) The air flow is mainly distrib- uted between the dashboard vents and the front and rear footwells. The air flow is distributed be- tween all the vents, the front side window demisting vents, the wind- screen demisting vents and the front and rear footwells.
  • Page 80 HeAtinG – ventiLAtiOn (2/2) Adjusting the air temperature Adjusting the amount of air blown into the passenger Turn button B. compartment Turning the control to the right increases Turn control C from 0 to 3. the temperature. The passenger compartment is ven- tilated by blown air.
  • Page 81 HeAtinG - Air COnDitiOninG (1/4) Adjusting the quantity of air Turn control C to the desired position. Turning the control to the right increases the amount of air supplied. If you wish to close the inlet fully and stop the function, move control C to 0 and control D to 0.
  • Page 82 HeAtinG - Air COnDitiOninG (2/4) The air flow is distributed be- tween the air vents, the wind- screen demisting vents and the foot wells. For more effective demist- ing, close the central dash- board vents and direct the side air vents towards the side windows.

  • Page 83: Air Conditioning

    HeAtinG - Air COnDitiOninG (3/4) Position 0 The air conditioning is not operating. In this position, ventilation is the same as for a vehicle without air condition- ing. Ñ the air conditioning is in normal operating mode. Air is taken from outside the vehicle, providing a continuous supply of fresh air.
  • Page 84 HeAtinG - Air COnDitiOninG (4/4) The air conditioning is at max- Prolonged use of the air recirculation imum operation. mode may cause the windows to mist up or lead to odours, as the air is not In this position, air is taken from the pas- renewed.

  • Page 85: Maintenance

    Air COnDitiOninG: information and advice on use Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours). Operating faults there is a risk of damage or of As a general rule, contact your ap- Fuel consumption fire.

  • Page 86: Interior Lighting

    interiOr LiGHtinG special features Depending on the vehicle, remote un- locking of the doors triggers timed light- ing of the passenger compartment. If one of the front or rear doors is opened, the period for which the light is switched on will start again.

  • Page 87: Sun Visor/Mirror/Windscreen

    sun visOr/MirrOr/WinDsCreen sun visor Courtesy mirrors 2 Heat reflecting windscreen Lower sun visor 1. This windscreen reflects the sun and special features on driver’s side limits the infrared rays entering the pas- If the sun visor is fitted with a courtesy senger compartment.

  • Page 88: Windows

    WinDOWs (1/2) Driver’s responsibility Never leave your vehi- cle with the key inside and never leave a child (or a pet) unsupervised, even for a short while. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or by locking the Front electric windows...
  • Page 89 WinDOWs (2/2) Opening the window on the Opening the sliding side sliding side door window To half-open the window, turn handle 4 Press catches 6 and slide the window in the direction of the arrow then lock open. it by pushing the handle to the right. To lock it in an open or closed position, Make sure it is properly latched into po- press button 5 and move the window...

  • Page 90: Ashtrays/Cigar Lighter/Accessories Socket

    AsHtrAys/CiGAr LiGHter/ACCessOries sOCket Accessories socket You can use the cigar lighter socket 1. It is designed for connecting acces- sories with a maximum power rating of 120 watts (voltage: 12V) which have been approved by our Technical Department. Depending on the battery charge, the accessories socket may stop working.

  • Page 91: Passenger Compartment Storage Space And Fittings

    PAssenGer COMPArtMent stOrAGe sPACe AnD FittinGs (1/3) Passenger side storage Cup holder 2 compartment Designed to accommodate cups, cans or the ashtray. To open the glove box, lift catch 1. Central storage compartment 3 When turning corners, accelerating or braking, Ensure that no hard, heavy ensure that the recepta- or pointed objects are...
  • Page 92 PAssenGer COMPArtMent stOrAGe sPACe AnD FittinGs (2/3) Front door storage sliding side door storage side panel storage compartment 4 compartment 5 compartment 6 Nothing should be placed Ensure that no hard, heavy on the floor area in front of or pointed objects are the driver as such objects placed in the “open”...
  • Page 93 PAssenGer COMPArtMent stOrAGe sPACe AnD FittinGs (3/3) upper cab storage Clothes hooks 11 A rail 10 on the right-hand side, fitted with two rings 8, enables objects to be compartment 7 Depending on the vehicle, hooks may secured in the luggage compartment be located in loading area A or on the (refer to the information on “Transporting partitions above the passenger seat.
  • Page 94 reAr BenCH seAt: functions (1/2) We would advise you to move the front seats forward slightly to make it easier to fold the seatback with the headrests in position. Make sure the headrests are in the cor- rect position when the seat is returned to its upright position.

  • Page 95: Rear Bench Seat : Functions

    reAr BenCH seAt functions (2/2) To maintain the rear bench seat in the raised position, attach retainer 4 to rod 3 of the passenger headrest. transporting bulky objects The small section may be folded down completely and yet still leave space to accommodate a maximum of two pas- sengers on the large section.

  • Page 96: Transporting Objects In The Luggage Compartment

    trAnsPOrtinG OBjeCts in tHe LuGGAGe COMPArtMent Always position the objects trans- ported so that the largest surface is against: – The rear bench seatbacks, for normal loads. – The folded bench seat, for maxi- mum loads. Always position the heavi- est items directly on the floor.

  • Page 97: Luggage Compartment Cover

    LuGGAGe COver The luggage compartment cover is B luggage cover in semi-folded posi- C luggage cover removed. made up of two rigid sections. tion. To remove the luggage compartment It can be used in one of three ways: cover, place it in the semi-folded posi- tion, take hold of the end and pull it to- A luggage cover in unfolded position.

  • Page 98: Luggage Net

    LuGGAGe net Luggage net 1 Fitting the net – lower section (behind the front seats, rear bench seat raised): attach the (depending on equipment level) can be – Upper section: attach the hooks 7 to belts 2 in the holes 8 located on the placed behind the front seats or behind the front or rear retractable mount- rear bench seat hinges;...
  • Page 99 Section 4: Maintenance Bonnet ............... . Engine oil level .

  • Page 100: Bonnet

    BOnnet Opening Closing Pull control 1 towards you. Check that nothing has been left in the engine compartment. Lift the bonnet, release stay 3 from its holder 2 and, for your safety, it is very Release the stay and replace it in its important to fix it at 4.
  • Page 101 engIne OIL LeveL: general information (1/2) If the level is at minimum: “ok” will not It is normal for an engine to use oil for Message 1 lubrication and cooling of moving parts appear on the display; dashes and “oil” Level above and it is normal to top up the level be- will flash (message 2) and, depending...
  • Page 102 engIne OIL LeveL: general information (2/2) Reading the level using the dipstick – Remove the dipstick (refer to the following pages for its location) and wipe it with a clean lint-free cloth; – push the dipstick in as far as it will go (for vehicles equipped with “cap-type dipstick”...

  • Page 103: Topping Up/Filling

    engIne OIL LeveL: topping up/filling (1/2) topping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). – Unscrew cap 1; –...

  • Page 104: Engine Oil Change

    engIne OIL LeveL: topping up/filling engIne OIL ChAnge (2/2) Oil change Filling: take care when Service interval: refer topping up the oil that Maintenance Service Booklet for your no oil drips onto engine vehicle. components - risk of fire. Remember to refit the cap securely Approximate capacities including oil as there is a risk of fire if oil splashes filter (for information).

  • Page 105: Brake Fluid Level

    LeveLS (1/3) If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from our network or from the manufacturer’s website. topping up After any operation on the hydraulic cir- cuit, a specialist must replace the fluid.
  • Page 106 LeveLS (2/3) Coolant Level checking intervals Check the level regularly (severe damage is likely to be caused to the engine if there is insufficient coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...

  • Page 107: Level, Filters

    LeveLS /FILteRS (3/3) Filters The replacement of filter elements (air filter, passenger compartment filter, diesel filter, etc.) is scheduled in the maintenance operations for your vehicle. Replacement intervals for filter el- ements: refer to the Maintenance Service Booklet for your vehicle. Power-assisted steering Screen wash reservoir pump (depending on vehicle)

  • Page 108: Battery

    BAtteRy The charge status of your battery can decrease especially if you use your ve- hicle: – for short journeys; – for driving in town; – when the temperature drops; – after extended use of consumers (radio etc.) with the engine switched off.

  • Page 109: Bodywork Maintenance

    BOdywORk MAIntenAnCe (1/2) Protection against the effects you should not: – Use solvents not approved by our Technical Department to remove of corrosive agents – Degrease or clean mechanical com- stains as this could damage the ponents (eg. the engine compart- Although your vehicle has been treated paintwork.
  • Page 110 BOdywORk MAIntenAnCe (2/2) you should – Observe the vehicle stopping dis- – Before going through a roller type tances when driving on gravelled car wash, return the windscreen – Wash your car frequently, with the surfaces to prevent paint damage. wiper stalk to park position (refer to engine off, with cleaning products the information on the “Windscreen...

  • Page 111: Interior Trim Maintenance

    InteRIOR tRIM MAIntenAnCe – Seat belts you should not: Whatever type of stain is on the trim, use soapy water (if possible, warm wa- These must be kept clean. You are strongly advised not to position ter) containing: objects such as deodorants, scents, etc. Use products selected by our –...
  • Page 112 4.14...

  • Page 113: Practical Advice

    Section 5: Practical advice Puncture ..............Wheel trims .

  • Page 114: Puncture

    PuncturE Wheelbrace 1 Emergency spare wheel 3   Jack 6 under the vehicle This is located in the engine compart- This is located in compartment 7 inside ment and is used to remove wheel the emergency spare wheel. This is stored in cradle 4 under the floor bolts, to release the cage 4 which holds at the rear of the vehicle.

  • Page 115: Wheel Trims

    WhEEl trims Wheel trim 1 Wheel trim 3 (concealed wheel bolts) (exposed wheel bolts) Remove it using hubcap tool 2 (located To remove it without removing the under the tool kit), by pushing the hook wheel, press it at the points indicated into the opening located near the valve by the arrows.

  • Page 116: Changing A Wheel

    chAnging A WhEEl Insert wheelbrace end-piece 4 into jack 3 and turn a few times to lift the wheel off the ground. Remove the bolts. Take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub.

  • Page 117: Tyres

    tyrEs  (1/3) tyre and wheel safety When the tyre tread has been worn to the level of the wear indicators, they    The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.
  • Page 118 tyrEs  (2/3) tyre pressures Fitting new tyres Pressures should be checked when the tyres are cold; ignore higher pressures Respect the tyre pressures (including which may be reached in hot weather the emergency spare wheel). Check For safety reasons, this op- or following a fast journey. them at least once a month and before eration must be carried out a long journey (refer to the label on the...
  • Page 119 tyrEs  (3/3) changing wheels around use in winter Chains may only be fitted This practice is not recommended. chains to tyres of the same size as those originally fitted to For  safety  reasons,  fitting  snow    your vehicle. chains to the rear axle is strictly for-  bidden. Only certain chains can be fitted to tyres.

  • Page 120: Changing Bulbs

    FrOnt lights: changing bulbs  (1/2) Dipped beam/main beam   Bulb type: h4, approved by our   technical Department (see box). To comply with local legislation, or headlights as a precaution, you can obtain an Remove the plastic cover by pressing Do not touch the bulb glass. hold it   emergency kit containing a set of tab 1. by its base. spare bulbs and fuses from an ap- Replace the bulb, pointing wider strip 7 proved Dealer.
  • Page 121 FrOnt lights: changing bulbs  (2/2) cleaning the headlights As the headlights are made of plastic glass, use a soft cloth or cotton wool to clean them. If this does not clean it properly, moisten the cloth with soapy water, then wipe clean with a soft damp cloth or cotton wool.
  • Page 122 FOg light: changing bulbs Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved dealer. light A Consult your approved Dealer. Bulb type: h1 Any operation on (or modi- fication to) the electrical system must be performed by an approved dealer since an incorrect connection might damage the electrical equipment The engine may be hot...

  • Page 123: Fog Lights

    rEAr lights: changing bulbs  (1/3) rear lights Unclip the bulb holder by pressing on tab 2. Remove nuts 1 and release the rear light from its housing. 3 side and brake light Pear-shaped, bayonet type bulb with 2 P 21/5 W filaments. 4 indicator P 21 W pear-shaped, bayonet type bulb. 5 reversing ...
  • Page 124 rEAr lights: changing bulbs  (2/3) high-level brake light 7  Bulb type P 21/5 W. Remove nuts 6 and release the brake light from its housing. 5.12...
  • Page 125 rEAr lights: changing bulbs  (3/3) number plate light Release the light to access bulbs 9. Unclip the light at 8 using a flat-blade Bulb type:  W 5 W. screwdriver or similar. 5.13...
  • Page 126 inDicAtOr lights: changing bulbs Unclip indicator light 1 using a flat-blade Turn bulb holder 2 a quarter of a turn screwdriver or similar. and take out the bulb. Bulb type: W5W. 5.14...
  • Page 127 intEriOr lighting: changing bulbs  (1/3) Passenger compartment light map reading light Release bulb 3. (depending on vehicle) – Remove the light support by press- Bulb type: 7 W festoon type bulb. Remove light covers 1 using a tool such ing on tab 2. as a flat-blade screwdriver. Bulb mounting 4 will fall out when re- leased.
  • Page 128 intEriOr lighting: changing bulbs  (2/3) Passenger compartment   map reading light – Remove bulb 9. light 7 – Remove lens 8 using a flat-blade Bulb type: 7 W festoon type bulb. (depending on vehicle) screwdriver or similar. – Tilt lens 7. – Release bulbs 10. – Remove it by hand. Bulb type: 7 W festoon type bulb. 5.16...
  • Page 129 intEriOr lighting: changing bulbs  (3/3) Passenger compartment   Release bulb 12. light 11 Bulb type: 7 W festoon type bulb. (depending on vehicle) – Tilt lens 11. – Remove it by hand. 5.17...
  • Page 130 light FOr luggAgE cOmPArtmEnt: changing bulbs light A light B Press tabs 1 to release the bulb holder. Unclip light B on the side indicated (using a flat-blade screwdriver or simi- Press tab 2 to release the lens and lar). access bulb 3. Bulb type: 10 W festoon type bulb Bulb type: 7 W festoon type bulb. Open flap 4 located at the rear of the light.
  • Page 131 BAttEry: troubleshooting  (1/2) to avoid all risk of sparks: As the battery is specific    – Ensure that any consumers (cour- to the vehicle (presence of tesy lights, etc.) are switched off a ventilation pipe to expel before disconnecting or reconnect- corrosive and explosive ing the battery. gases), make sure that it is replaced with a battery that enables this pipe –...

  • Page 132: Battery: Troubleshooting

    BAttEry: troubleshooting  (2/2) starting the vehicle using the   Connect the positive (+) lead A to (+) terminal 1 of the discharged battery, battery from another vehicle then to (+) terminal 2 of the battery sup- If you have to use the battery from an- plying the current. other vehicle to start, obtain suitable Connect the negative (–) lead B to (–) jump leads (with a large cross section) terminal 3 of the battery supplying the...

  • Page 133: Fuses

    FusEs  (1/3) incOrrEct cOrrEct Fuse box 1 Unclip cover 3 (under the steering Remove the fuse using tweezers 2. wheel). To remove the fuse from the tweez- If an electrical component does not To identify the fuses, refer to fuse allo- ers, slide the fuse in the direction of the work, check the condition of the fuses.
  • Page 134 FusEs  (2/3) Allocation of fuses (the presence of the fuses DEPEnDs On thE VEhiclE’s EQuiPmEnt lEVEl) symbol Allocation symbol Allocation symbol Allocation Instrument panel/ Electric locking/ Electric windows/ Electric door mirrors/ Immobiliser/General General supply Radio/Car phone supply Courtesy light/Luggage ñ Heated seats compartment light Front fog lights ö Rear screen washer/ Consumer cut-out Not used wiper/Reversing lights...
  • Page 135 FusEs  (3/3) Allocation of fuses (the presence of the fuses DEPEnDs On thE VEhiclE’s EQuiPmEnt lEVEl) symbol Allocation symbol Allocation symbol Allocation Cigar lighter/accessories Right-hand side light/ Æ Ä socket Instrument lighting Left-hand main beam Rear fog light/ headlight/Instrument û Instrument panel Not used panel Right-hand main beam Flasher unit headlight Alarm/General supply Left-hand dipped beam Ì...

  • Page 136: Wiper Blades

    WinDscrEEn WiPEr BlADEs  (1/2) replacing windscreen wiper   refitting a front or rear wiper   blades 1 blade Lift wiper arm 3. Proceed in reverse order. Make sure Turn the wiper blade until it is horizon- that the blade is correctly locked in po- tal. sition. Check the condition of the wiper Press tab 2 and slide the wiper blade blades.
  • Page 137 WinDscrEEn WiPEr BlADEs  (2/2) replacing the rear screen   wiper blade (tailgate) – In frosty weather, make Lift wiper arm 8. sure that the wiper blades are not stuck by ice (to Pivot blade 9 until some resistance is avoid the risk of the motor met. overheating). Pull the blade to release it (move- –...

  • Page 138: Towing: Breakdown

    tOWing: breakdown Do not leave the tools unse- cured inside the vehicle as they may come loose under braking. the  steering  wheel  must  be  un-  Only use the front 1 and rear towing    – Use a rigid towing bar. If a locked and the ignition key must be    points 2 (never use the drive shafts). rope or cable is used (where in position m (ignition on) to provide ...
  • Page 139 tOWing: equipment A = 776.5 mm. Permissible  nose  weight,  maxi-  mum permissible towing weight,    braked  and  unbraked:  refer to the information on “Weights” in Section 6. Refer to the manufacturer’s instruc- tions for information on how to fit and operate the towing equipment. Please keep these instructions with the rest of the vehicle documenta- tion.

  • Page 140: Fitting A Radio

    Fitting A rADiO radio location 1 Front speakers rear speakers Unclip and remove the storage com- Unclip grille 2 using a flat-blade screw- Remove the luggage cover to gain partment, the aerial connections, + driver or similar, at the arrows. access to speaker locations 3. and – feed wires, and left and right speaker wires attached to the back of the storage compartment.

  • Page 141: Accessories

    AccEssOriEs Before fitting an electrical or If you are using an anti-theft electronic device (particu- device, only attach it to the larly for transmitters/receiv- brake pedal. ers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle.
  • Page 142 systEm FOr cutting OFF FuEl suPPly in thE EVEnt OF A sEVErE imPAct Your vehicle is equipped with a system for cutting off fuel in the event of a se- vere impact. This system is designed to disable and thus isolate the fuel supply system if a severe impact occurs. Enabling the system If the conditions for restarting the fuel Following an impact, the supply system are met (see box), press system can be reinitialised,...

  • Page 143: Radio Frequency Remote Control: Batteries

    rADiO FrEQuEncy rEmOtE cOntrOl: batteries Unclip remote control cover 1 (using a Replace battery 2 according to the di- coin). rection marked on the cover. note:  It is not advisable to touch the electronic circuit in the key cover when replacing the battery. Batteries can be obtained from your approved Dealer.

  • Page 144: Diesel Filter

    DiEsEl FiltEr repriming the fuel circuit If the vehicle runs out of fuel completely, it is necessary to actuate the manual priming bulb after having refilled. Vehicles with manual priming pump The peripheral components (alter- – If fitted to the vehicle, turn the bleed nator, starter, engine mountings, screw located on the diesel filter.

  • Page 145: Operating Faults

    OPErAting FAults  (1/4) the following advice will enable you to carry out quick, temporary repairs. For safety reasons, you should always contact    an approved Dealer as soon as possible. the starter is activated POssiBlE cAusEs WhAt tO DO Warning lights dim or fail to come on; Battery terminals disconnected, Retighten, reconnect or clean them if they the starter does not run. oxidised or incorrectly secured. are oxidised. Battery discharged or worn. Connect another battery to the faulty bat- tery.
  • Page 146 OPErAting FAults  (2/4) On the road POssiBlE cAusEs WhAt tO DO Vibrations. Tyres not inflated to the correct pres- Check the tyre pressures: if this is not the sure, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer. Abnormal white smoke from the exhaust Mechanical fault: cylinder head Stop the engine.
  • Page 147 OPErAting FAults  (3/4) On the road POssiBlE cAusEs WhAt tO DO Steering becomes heavy. Assistance overheating. Consult an approved Dealer. The engine overheats. The coolant Engine cooling fan not working. Stop the vehicle, switch off the engine and temperature indicator and the STOP contact an approved Dealer. warning light come on.
  • Page 148 OPErAting FAults  (4/4) Electrical equipment POssiBlE cAusEs WhAt tO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved Dealer. The wiper does not stop. Faulty electrical controls. Consult an approved Dealer. Direction indicators flashing more Blown bulb.

  • Page 149: Technical Specifications

    Section 6: Technical specifications Vehicle identification plates ............Engine specifications .

  • Page 150: Vehicle Identification Plates

    Vehicle identification plates (1/2) Quote the details given on the iden- A - Vehicle identification plate 6 Technical specifications of the tification plate A (right-hand side) on vehicle. all letters or orders. 1 Vehicle type and chassis number. 7 Vehicle paint reference. 2 Maximum permissible all-up...
  • Page 151 Vehicle identification plates (2/2) Quote the details given on engine plate B on all letters or orders. B – engine plate or engine label (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.

  • Page 152: Engine Specifications

    engine specifications engines 1.2 16V 1.5 dci engine type (see engine plate) cubic capacity (cc) 1 149 1461 type of fuel Unleaded fuel Diesel octane rating 95 or 98* The label by the filler neck indicates which types of fuel are authorised. spark plugs Only use the spark plugs specified for your vehicle’s engine.

  • Page 153: Weights

    Weights (in kg) (1/2) the weights indicated for a basic vehicle without options: they vary depending on your vehicle’s equipment. contact an approved dealer. Van versions petrol diesel all-terrain Maximum permissible all-Up Weight (MMac) Weights indicated on the identification plate Maximum permissible total Weight (MMta) (refer to the information on the “Vehicle total train Weight (MtR)
  • Page 154 Weights (in kg) (2/2) the weights indicated for a basic vehicle without options: they vary depending on your vehicle’s equipment. contact an approved dealer. coMBi versions petrol/diesel all-terrain Maximum permissible all-Up Weight (MMac) Weights indicated on the identification plate Maximum permissible total Weight (MMta) (refer to the information on the “Vehicle total train Weight (MtR) identification plates”...

  • Page 155: Dimensions

    diMensions (in metres) 2.015 0.730 2.605 0.700 1.405 4.035 2.031 turning circle – between walls: 10.79 1.835 (1) important: if the vehicle is fitted with roof bars, the various height 1.730 (2) measurements, shown opposite, must be increased by 4.3 cm. 1.885 (1) (3) these bars cannot be removed.

  • Page 156: Replacement Parts And Repairs

    ReplaceMent paRts and RepaiRs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.

  • Page 157: Service Sheets

    seRVice sheets (1/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 158 seRVice sheets (2/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 159 seRVice sheets (3/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 160 seRVice sheets (4/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 161 seRVice sheets (5/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
  • Page 162 seRVice sheets (6/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...

  • Page 163: Anticorrosion Check

    anticoRRosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.15...
  • Page 164 anticoRRosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.16...
  • Page 165 anticoRRosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.17...
  • Page 166 anticoRRosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.18...
  • Page 167 anticoRRosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.19...
  • Page 168 anticoRRosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.20...

  • Page 169: Alphabetical Index

    AlphABEtiCAl inDEx (1/2) ABS ................... 2.11 dipstick................ 4.3 – 4.4 accessories................ 5.29 doors................1.5 → 1.11 advice on antipollution ..........2.6 → 2.8 driving .................. 2.4 air bag..............1.22 → 1.26 activating the front passenger air bags ......1.38 electric windows ............. 3.14 – 3.15 deactivating the front passenger air bags ....1.37 emergency brake assist.............
  • Page 170 AlphABEtiCAl inDEx (1/2) direction indicators ............1.42 gear lever................2.10 fog lights ..............1.42 main beam headlights ..........1.42 side lights ..............1.42 handbrake................2.10 lights-on warning buzzer..........1.6, 1.50 hazard warning lights signal ..........1.39 luggage compartment cover ..........3.23 headlight beam adjustment ..........
  • Page 171 ................5.5 → 5.7 rear view mirrors ..............1.17 remote control electric door locking ......1.2 → 1.4 vehicle identification ........... 6.2 – 6.3 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.11 vehicle identification plates ......... 6.2 – 6.3 replacement parts ..............6.8 ventilation ..........3.2 – 3.3, 3.5 → 3.11 running in ................2.2 warning lights............1.42 → 1.45...

  • Page 172: For Your Safety

    4 SIMPLE ACTIONS* FOR YOUR SAFETY • Always fasten • Always secure children • Adjust the height of • Place heavy objects or your seat belt, using devices suitable the seat belt according luggage at the back of the – even for short journeys for their size and weight to your size.
  • Page 173 à8201076126í î í ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Table of Contents