Programming And Option Boards - Motorola GP68 Service Manual

GP68 Portable Radios Service Manual
Receive and Transmit PL/DPL Code
Tables
When selecting a Receive or Transmit PL/DPL code,
Table 4-3, Receive and Transmit PL/DPL Codes, on
rPL.XXX PL FREQ EQUIV. rPL.XXX
tPL.XXX (Hz) PL CODE tPL.XXX
000 CSQ -
001 67.0 XZ
002 69.3 WZ
003 71.9 XA
004 74.4 WA
005 77.0 XB
006 79.7 WB
007 82.5 YZ
008 85.4 YA
009 88.5 YB
010 91.5 ZZ
011 94.8 ZA
012 97.4 ZB
013 100.0 1Z
014 103.5 1A
015 107.2 1B
016 110.9 2Z
017 114.8 2A
018 118.8 2B
019 123.0 3Z
020 127.3 3A
021 131.8 3B

Programming and Option Boards

NOTE
It is not necessary for a Dealer's radio to have
an option board installed in order to perform
the programming.
If no Option Boards were Installed in the
Dealer's Radio
• Select the appropriate option board setting via the
Option Board Setup Mode.
• Perform all necessary channel programming func-
tions, including default radio settings, channel set-
tings, and phone numbers.
March, 1997
Table 4-3 Receive and Transmit PL/DPL Codes
PL FREQ EQUIV.
(Hz) PL CODE
022 136.5 4Z
023 141.3 4A
024 146.2 4B
025 151.4 5Z
026 156.7 5A
027 162.2 5B
028 167.9 6Z
029 173.8 6A
030 179.9 6B
031 186.2 7Z
032 192.8 7A
033 203.5 M1
034 206.5 8Z
035 210.7 M2
036 218.1 M3
037 225.7 M4
038 229.1 9Z
039 233.6 M5
040 241.8 M6
041 250.3 M7
042 254.1 OZ
page 4-9, gives the PL frequencies, equivalent PL codes (if
applicable) and DPL codes corresponding to the display
rPL.XXX or tPL.XXX where XXX is in the range 001 to
126. rPL.000 and tPL.000 represents Carrier squelch (CSQ)
for Receive and Transmit respectively.
rPL.XXX EQUIV. rPL.XXX EQUIV.
tPL.XXX DPL CODE tPL.XXX DPL CODE
043 23 065
044 25 066
045 26 067
046 31 068
047 32 069
048 43 070
049 47 071
050 51 072
051 54 073
052 65 074
053 71 075
054 72 076
055 73 077
056 74 078
057 114 079
058 115 080
059 116 081
060 125 082
061 131 083
062 132 084
063 134 085
064 143 086
• Perform any programming of DTMF Selective Call
IDs (if necessary), and configure SPM defaults.
• Clone the programmed settings over to the user
radios.
If an Option Board is Installed in the
Dealer's Radio
In this procedure, you would not be able to
select Signalling Squelch Mode as a channel
default. However, if you do need to do so,
remove the Option Board and follow the steps
outlined in If no Option Boards were
Installed in the Dealer's Radio.
6881086C09-O
Radio Programming Information
Programming and Option Boards
rPL.XXX EQUIV. rPL.XXX
tPL.XXX DPL CODE tPL.XXX
152 087 343 109
155 088 346 110
156 089 351 111
162 090 364 112
165 091 365 113
172 092 371 114
174 093 411 115
205 094 412 116
223 095 413 117
226 096 423 118
243 097 431 119
244 098 432 120
245 099 445 121
251 100 464 122
261 101 465 123
263 102 466 124
265 103 503 125
271 104 506 126
306 105 516
311 106 532
315 107 546
331 108 565
NOTE
EQUIV.
DPL CODE
606
612
624
627
631
632
645
654
662
664
703
712
723
731
732
734
743
754
4-9