Sony PVM-20M2U Service Manual page 12

......
1\)
I
Using On-Screen Menus
To display the next (or previous) page of the
menus
Select NEXT PAGE on the menu to display the next
page and PREVIOUS PAGE on the menu to display
the previous page.
MENU I
(;OC.OfiiYITEIIIIOII'UY
Ul TM,FHTEII
~U:~~C::~
.. ~:'"~AU
. . . UECTHI
...
+-
MENU2
•PIIEVICUIPAQIE
~T~EWIL
f~;n.uvu
-IUCTIII
-+ :
When selecting NEXT PAGE
+- :
When selecting PREVIOUS PAGE
How to display the next or the previous page
To close the menu (to return to the regular
screen)
Each time you press the MENU/EXIT
<OJ
button, the
on-screen menu returns to the one previously
displayed. Press the MENU/EXIT (0) button
repeatedly until the regular screen appears.
For PVM-14M4E/14M2E/20M4E/20M2E:
For the first time when the monitor is turned on, the
LANGUAGE menu(~) will appear on the screen.
So, select the language you want to use.
•EifGLIIH
DEUTSCH
'""""'"''
ITALIANO
ESPAIIOi.
1
Move the
cursor(~)
to the desired language by
pressing the..,,_ or
tl+
(0,
E))
button.
2
Press the MENU/EXIT
(0)
button.
..
Unless you press the MENU/EXIT (0) button in
the procedure above, the LANGUAGE menu will
always appear whenever you tum on the monitor.
1!2
f.f{!!l,p_!Lon§.~Qf Q~l}:~.9!!~n·. ~',EL!S
..,_j
There are four types of on-screen menus.
Main menu
You can enter another menu such as status menu or
setting menu.
Status menu
You can confirm the current settings.
Setting menu
You can select an item or enter an adjustment
screen on this menu by using the
tl+,
..,,_and
ENTER/SELECT buttons.
Adjustment screen
You can make adjustments on this screen. The
adjustments you made remain unchanged until next
change even if you tum off the power.
([I indicates the factory setting.)
[I]Main menu
Select another menu and press ENTER/SELECT to go
to the menu.
~STATUS 1 menu
Shows the current settings.
~STATUS 2 menu
Shows what optional kit is installed in the monitor.
~CHROMA SET UP menu
Select ON on this menu to activate "chroma" and
"phase" (NTSC signal on!ll adjustments done on the
AUTO ADJUST screen ([lj). [OFF]
@]COLOR TEMP/BAL menu
Select the color temperature from among D65, D93
and USER. USER is set to D65 as the factory setting.
You can adjust or change the color temperature in
USER mode (a measuring instrument is required).
[D65)
[§)CAPTION VISION menu
This menu is provided only for PVM-14M4U/14M2U/
20M4U/20M2U.
The monitor can display the signal with Caption
Vision. To display it, select the caption type in this
menu. [OFF]
~USER CONFIG 1 menu
Select an item to adjust on the menus and screens
(1J11
through~).
To go to the USER CONFIG 2 menu,
select NEXT PAGE.
~USER CONFIG 2 menu
Select an item to adjust on the menus and screens
(~
through ~). To go to the USER CONFIG I menu
select PREVIOUS PAGE.
[l]AUTO ADJUST screen
Select the color bar signal (full, SMPTE, EIA) and
press ENTER/SELECT to start automatic "chroma"
and "phase" (NTSC signal only) adjustments.
To activate these adjustments, select ON on the
CHROMA SET UP menu (~).
(IDADJUST GAIN screen
Adjust GAIN in USER mode.
[IDADJUST BIAS screen
Adjust BIAS in USER mode.
llli!COLOR TEMP RANGE menu
Select the color temperature range in USER mode.
[5000K-IOOOOK]
!!]USER COPY menu
Store the factory setting of D65 or D93 as the value for
USER mode.
IJ1ICOLOR SYSTEM DISPLAY menu
Select the color system type. When AUTO is selected,
the color system type being used appears on the screen
each time you change the signal input. [AUTO]
~358
TRAP FIL TEA menu
Color spill or color noise may be eliminated if you
select ON (NTSC signal only).
Normally select OFF. [OFF]
IH]SUB CONTROL menu
Select an item (CONTRAST, BRIGHT, CHROMA
and PHASE controls on the front panel) to finely
adjust on the SUB CONTROL screen (11]) .
[§]SUB CONTROL screen
Finely adjust the selected item on the SUB CONTROL
menu (IH]). Each control (CONTRAST, BRIGHT,
CHROMA and PHASE control) has a click position at
the center of its adjustment range. You can adjust the
setting of the click position with this feature.
[§]USER PRESET menu
If you select ON on this menu, the REMOTE indicator
lights up and the controls on the front panel do not
work. The monitor operates with the user preset
settings.
To adjust the use!:_P.reset settings, select the PRESET
ADJUST menu (111J). [OFF]
111!PRESET ADJUST menu
You can preset the BRIGHT, CHROMA, PHASE,
CONTRAST, VOLUME, and APERTURE controls to
a desired level and can use these settings by selecting
ON on the USER PRESET menu ([§]).
imPRESET ADJUST screen
Adjust the selected item (BRIGHT, CHROMA,
PHASE, CONTRAST, VOLUME, and APERTURE
control) on the PRESET ADJUST menu (111!).
~V
HOLD screen
Adjust the vertical hold if the picture rolls vertically.
When you cannot read the display, select the input that
is not connected.
~COMPONENT
LEVEL menu
Select the component level from among three modes.
N I 0/SMPTE for I 00/01100/0 signal
BETA 7.5
for IOOn.5n5n.5 signal
BETA 0 for IOO/On5/0 signal
For PVM-14M4U/14M2U/20M4U/20M2U
[BETA 7.5)
For PVM-14M4E/14M2E/20M4E/20M2E
[NIO/SMPTE)
13