Selecting A Screen Size Automatically; Detecting Side Masks; Changing The Brightness At Both Sides Of The Screen (Side Mask) - Pioneer PDP-5080HD Operating Instructions Manual

Adjustments and Settings
11
• You can freely change the screen size while watching HD
broadcasts or enjoying other HD input sources. However,
when you resume the HD programs after having quit them,
"FULL" is automatically selected for the screen size.
• The specifications given for the PC source is for the PDP-
5080HD. For the PDP-4280HD, the number of panel pixels is
different, and thus signal processing and actual viewing
conditions will vary slightly.
• It is not recommended to consistently display signals that do
not completely fill the screen. This may cause temporary or
permanent image retention depending on the frequency and
duration.
AV source
4:3
CINEMA
ZOOM

Selecting a screen size automatically

The plasma display automatically selects an appropriate screen
size when video signals are received from a connected HDMI
device (see page 65). To activate this function, use the following
procedure.
1
Press HOME MENU.
2
Select "Option" ( /
3
Select "Auto Size" ( /
4
Select "Natural" or "Wide-Zoom" ( /
Item Description
Off Deactivates the Auto Size function
Natural
Naturally adjusts the image to the screen
Wide-Zoom
Enlarges and displays only the 4:3 aspect ratio portion in
full and wide screen
5
Press HOME MENU to exit the menu.
Note
• Manually select an appropriate screen size if an image does
not automatically switch to a correct screen format.
• When the video signal contains no aspect ratio information,
the function will not work even with "Natural" or "Wide-Zoom"
selected.
62
En
PC source
4:3
WIDE
FULL
FULL
then ENTER).
then ENTER).
then ENTER).

Detecting side masks

Some HD broadcasts may display 4:3 content with side masks.
The plasma display automatically detects these side masks to
provide gray side masks when "Natural" has been selected for
"Auto Size", or display the image full screen with the side masks
removed when "Wide-Zoom" has been selected. This function
does not operate when "Off" is selected for "Auto Size".
1
Press HOME MENU.
2
Select "Option" ( / then ENTER).
3
Select "Side Mask" ( /
4
Select "Detection" ( / ).
5
Select "On" ( / ).
Item Description
Off Deactivates the Side Mask detection
On
Activates the Side Mask detection
6
Press HOME MENU to exit the menu.
Important
• The "On" setting prevents uneven wear on 4:3 content and side
masks and can reduce the possibility of image retention.
Note
• You cannot set the Side Mask detection to "On" or "Off" when
"Off" is selected in "Auto Size".
• Set the Side Mask detection function to "On". The High
Definition 16:9 aspect ratio images containing side masks will
be detected automatically and side masks will be added or the
image displayed in full screen.
• This Side Mask detection does not operate on 4:3 content
displayed in SD (standard definition) broadcasts.
• "AUTO" will appear on the channel display when this function
is on.
• Detection errors may occur depending on the HD content. In
case a detection error occurs, manually change the screen size
to the desired size.
• Side Mask detection may not operate properly for video signals
that contain no aspect ratio information. If that is the case,
check if "FULL" is selected for the screen size, switch to
another input source, then switch back to the original input
source again.
Changing the brightness at both sides of
the screen (Side Mask)
With the 4:3 screen size, you can change the brightness of the
gray side masks that appear at both sides of the screen.
1
Press HOME MENU.
2
Select "Option" ( / then ENTER).
3
Select "Side Mask" ( /
4
Select "Brightness Sync." ( / ).
5
Select the desired parameter ( / ).
Item Description
Fixed (default) Always sets the same brightness for the gray side masks
Auto
Adjusts the brightness of the gray side masks according to
the brightness of images
then ENTER).
then ENTER).